2 * New driver for Marvell Yukon 2 chipset.
3 * Based on earlier sk98lin, and skge driver.
5 * This driver intentionally does not support all the features
6 * of the original driver such as link fail-over and link management because
7 * those should be done at higher levels.
9 * Copyright (C) 2005 Stephen Hemminger <shemminger@osdl.org>
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License as published by
13 * the Free Software Foundation; either version 2 of the License.
15 * This program is distributed in the hope that it will be useful,
16 * but WITHOUT ANY WARRANTY; without even the implied warranty of
17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
18 * GNU General Public License for more details.
20 * You should have received a copy of the GNU General Public License
21 * along with this program; if not, write to the Free Software
22 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
25 #include <linux/crc32.h>
26 #include <linux/kernel.h>
27 #include <linux/version.h>
28 #include <linux/module.h>
29 #include <linux/netdevice.h>
30 #include <linux/dma-mapping.h>
31 #include <linux/etherdevice.h>
32 #include <linux/ethtool.h>
33 #include <linux/pci.h>
36 #include <linux/tcp.h>
38 #include <linux/delay.h>
39 #include <linux/workqueue.h>
40 #include <linux/if_vlan.h>
41 #include <linux/prefetch.h>
42 #include <linux/debugfs.h>
43 #include <linux/mii.h>
47 #if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
48 #define SKY2_VLAN_TAG_USED 1
53 #define DRV_NAME "sky2"
54 #define DRV_VERSION "1.15"
55 #define PFX DRV_NAME " "
58 * The Yukon II chipset takes 64 bit command blocks (called list elements)
59 * that are organized into three (receive, transmit, status) different rings
63 #define RX_LE_SIZE 1024
64 #define RX_LE_BYTES (RX_LE_SIZE*sizeof(struct sky2_rx_le))
65 #define RX_MAX_PENDING (RX_LE_SIZE/6 - 2)
66 #define RX_DEF_PENDING RX_MAX_PENDING
67 #define RX_SKB_ALIGN 8
69 #define TX_RING_SIZE 512
70 #define TX_DEF_PENDING (TX_RING_SIZE - 1)
71 #define TX_MIN_PENDING 64
72 #define MAX_SKB_TX_LE (4 + (sizeof(dma_addr_t)/sizeof(u32))*MAX_SKB_FRAGS)
74 #define STATUS_RING_SIZE 2048 /* 2 ports * (TX + 2*RX) */
75 #define STATUS_LE_BYTES (STATUS_RING_SIZE*sizeof(struct sky2_status_le))
76 #define TX_WATCHDOG (5 * HZ)
77 #define NAPI_WEIGHT 64
78 #define PHY_RETRIES 1000
80 #define SKY2_EEPROM_MAGIC 0x9955aabb
83 #define RING_NEXT(x,s) (((x)+1) & ((s)-1))
85 static const u32 default_msg
=
86 NETIF_MSG_DRV
| NETIF_MSG_PROBE
| NETIF_MSG_LINK
87 | NETIF_MSG_TIMER
| NETIF_MSG_TX_ERR
| NETIF_MSG_RX_ERR
88 | NETIF_MSG_IFUP
| NETIF_MSG_IFDOWN
;
90 static int debug
= -1; /* defaults above */
91 module_param(debug
, int, 0);
92 MODULE_PARM_DESC(debug
, "Debug level (0=none,...,16=all)");
94 static int copybreak __read_mostly
= 128;
95 module_param(copybreak
, int, 0);
96 MODULE_PARM_DESC(copybreak
, "Receive copy threshold");
98 static int disable_msi
= 0;
99 module_param(disable_msi
, int, 0);
100 MODULE_PARM_DESC(disable_msi
, "Disable Message Signaled Interrupt (MSI)");
102 static int idle_timeout
= 100;
103 module_param(idle_timeout
, int, 0);
104 MODULE_PARM_DESC(idle_timeout
, "Watchdog timer for lost interrupts (ms)");
106 static const struct pci_device_id sky2_id_table
[] = {
107 { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT
, 0x9000) }, /* SK-9Sxx */
108 { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT
, 0x9E00) }, /* SK-9Exx */
109 { PCI_DEVICE(PCI_VENDOR_ID_DLINK
, 0x4b00) }, /* DGE-560T */
110 { PCI_DEVICE(PCI_VENDOR_ID_DLINK
, 0x4001) }, /* DGE-550SX */
111 { PCI_DEVICE(PCI_VENDOR_ID_DLINK
, 0x4B02) }, /* DGE-560SX */
112 { PCI_DEVICE(PCI_VENDOR_ID_DLINK
, 0x4B03) }, /* DGE-550T */
113 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4340) }, /* 88E8021 */
114 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4341) }, /* 88E8022 */
115 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4342) }, /* 88E8061 */
116 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4343) }, /* 88E8062 */
117 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4344) }, /* 88E8021 */
118 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4345) }, /* 88E8022 */
119 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4346) }, /* 88E8061 */
120 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4347) }, /* 88E8062 */
121 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4350) }, /* 88E8035 */
122 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4351) }, /* 88E8036 */
123 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4352) }, /* 88E8038 */
124 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4353) }, /* 88E8039 */
125 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4356) }, /* 88EC033 */
126 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4360) }, /* 88E8052 */
127 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4361) }, /* 88E8050 */
128 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4362) }, /* 88E8053 */
129 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4363) }, /* 88E8055 */
130 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4364) }, /* 88E8056 */
131 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4366) }, /* 88EC036 */
132 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4367) }, /* 88EC032 */
133 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4368) }, /* 88EC034 */
134 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x4369) }, /* 88EC042 */
135 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x436A) }, /* 88E8058 */
136 { PCI_DEVICE(PCI_VENDOR_ID_MARVELL
, 0x436B) }, /* 88E8071 */
140 MODULE_DEVICE_TABLE(pci
, sky2_id_table
);
142 /* Avoid conditionals by using array */
143 static const unsigned txqaddr
[] = { Q_XA1
, Q_XA2
};
144 static const unsigned rxqaddr
[] = { Q_R1
, Q_R2
};
145 static const u32 portirq_msk
[] = { Y2_IS_PORT_1
, Y2_IS_PORT_2
};
147 /* This driver supports yukon2 chipset only */
148 static const char *yukon2_name
[] = {
150 "EC Ultra", /* 0xb4 */
151 "Extreme", /* 0xb5 */
156 /* Access to external PHY */
157 static int gm_phy_write(struct sky2_hw
*hw
, unsigned port
, u16 reg
, u16 val
)
161 gma_write16(hw
, port
, GM_SMI_DATA
, val
);
162 gma_write16(hw
, port
, GM_SMI_CTRL
,
163 GM_SMI_CT_PHY_AD(PHY_ADDR_MARV
) | GM_SMI_CT_REG_AD(reg
));
165 for (i
= 0; i
< PHY_RETRIES
; i
++) {
166 if (!(gma_read16(hw
, port
, GM_SMI_CTRL
) & GM_SMI_CT_BUSY
))
171 printk(KERN_WARNING PFX
"%s: phy write timeout\n", hw
->dev
[port
]->name
);
175 static int __gm_phy_read(struct sky2_hw
*hw
, unsigned port
, u16 reg
, u16
*val
)
179 gma_write16(hw
, port
, GM_SMI_CTRL
, GM_SMI_CT_PHY_AD(PHY_ADDR_MARV
)
180 | GM_SMI_CT_REG_AD(reg
) | GM_SMI_CT_OP_RD
);
182 for (i
= 0; i
< PHY_RETRIES
; i
++) {
183 if (gma_read16(hw
, port
, GM_SMI_CTRL
) & GM_SMI_CT_RD_VAL
) {
184 *val
= gma_read16(hw
, port
, GM_SMI_DATA
);
194 static u16
gm_phy_read(struct sky2_hw
*hw
, unsigned port
, u16 reg
)
198 if (__gm_phy_read(hw
, port
, reg
, &v
) != 0)
199 printk(KERN_WARNING PFX
"%s: phy read timeout\n", hw
->dev
[port
]->name
);
204 static void sky2_power_on(struct sky2_hw
*hw
)
206 /* switch power to VCC (WA for VAUX problem) */
207 sky2_write8(hw
, B0_POWER_CTRL
,
208 PC_VAUX_ENA
| PC_VCC_ENA
| PC_VAUX_OFF
| PC_VCC_ON
);
210 /* disable Core Clock Division, */
211 sky2_write32(hw
, B2_Y2_CLK_CTRL
, Y2_CLK_DIV_DIS
);
213 if (hw
->chip_id
== CHIP_ID_YUKON_XL
&& hw
->chip_rev
> 1)
214 /* enable bits are inverted */
215 sky2_write8(hw
, B2_Y2_CLK_GATE
,
216 Y2_PCI_CLK_LNK1_DIS
| Y2_COR_CLK_LNK1_DIS
|
217 Y2_CLK_GAT_LNK1_DIS
| Y2_PCI_CLK_LNK2_DIS
|
218 Y2_COR_CLK_LNK2_DIS
| Y2_CLK_GAT_LNK2_DIS
);
220 sky2_write8(hw
, B2_Y2_CLK_GATE
, 0);
222 if (hw
->chip_id
== CHIP_ID_YUKON_EC_U
|| hw
->chip_id
== CHIP_ID_YUKON_EX
) {
225 reg
= sky2_pci_read32(hw
, PCI_DEV_REG4
);
226 /* set all bits to 0 except bits 15..12 and 8 */
227 reg
&= P_ASPM_CONTROL_MSK
;
228 sky2_pci_write32(hw
, PCI_DEV_REG4
, reg
);
230 reg
= sky2_pci_read32(hw
, PCI_DEV_REG5
);
231 /* set all bits to 0 except bits 28 & 27 */
232 reg
&= P_CTL_TIM_VMAIN_AV_MSK
;
233 sky2_pci_write32(hw
, PCI_DEV_REG5
, reg
);
235 sky2_pci_write32(hw
, PCI_CFG_REG_1
, 0);
237 /* Enable workaround for dev 4.107 on Yukon-Ultra & Extreme */
238 reg
= sky2_read32(hw
, B2_GP_IO
);
239 reg
|= GLB_GPIO_STAT_RACE_DIS
;
240 sky2_write32(hw
, B2_GP_IO
, reg
);
244 static void sky2_power_aux(struct sky2_hw
*hw
)
246 if (hw
->chip_id
== CHIP_ID_YUKON_XL
&& hw
->chip_rev
> 1)
247 sky2_write8(hw
, B2_Y2_CLK_GATE
, 0);
249 /* enable bits are inverted */
250 sky2_write8(hw
, B2_Y2_CLK_GATE
,
251 Y2_PCI_CLK_LNK1_DIS
| Y2_COR_CLK_LNK1_DIS
|
252 Y2_CLK_GAT_LNK1_DIS
| Y2_PCI_CLK_LNK2_DIS
|
253 Y2_COR_CLK_LNK2_DIS
| Y2_CLK_GAT_LNK2_DIS
);
255 /* switch power to VAUX */
256 if (sky2_read16(hw
, B0_CTST
) & Y2_VAUX_AVAIL
)
257 sky2_write8(hw
, B0_POWER_CTRL
,
258 (PC_VAUX_ENA
| PC_VCC_ENA
|
259 PC_VAUX_ON
| PC_VCC_OFF
));
262 static void sky2_gmac_reset(struct sky2_hw
*hw
, unsigned port
)
266 /* disable all GMAC IRQ's */
267 sky2_write8(hw
, SK_REG(port
, GMAC_IRQ_MSK
), 0);
268 /* disable PHY IRQs */
269 gm_phy_write(hw
, port
, PHY_MARV_INT_MASK
, 0);
271 gma_write16(hw
, port
, GM_MC_ADDR_H1
, 0); /* clear MC hash */
272 gma_write16(hw
, port
, GM_MC_ADDR_H2
, 0);
273 gma_write16(hw
, port
, GM_MC_ADDR_H3
, 0);
274 gma_write16(hw
, port
, GM_MC_ADDR_H4
, 0);
276 reg
= gma_read16(hw
, port
, GM_RX_CTRL
);
277 reg
|= GM_RXCR_UCF_ENA
| GM_RXCR_MCF_ENA
;
278 gma_write16(hw
, port
, GM_RX_CTRL
, reg
);
281 /* flow control to advertise bits */
282 static const u16 copper_fc_adv
[] = {
284 [FC_TX
] = PHY_M_AN_ASP
,
285 [FC_RX
] = PHY_M_AN_PC
,
286 [FC_BOTH
] = PHY_M_AN_PC
| PHY_M_AN_ASP
,
289 /* flow control to advertise bits when using 1000BaseX */
290 static const u16 fiber_fc_adv
[] = {
291 [FC_BOTH
] = PHY_M_P_BOTH_MD_X
,
292 [FC_TX
] = PHY_M_P_ASYM_MD_X
,
293 [FC_RX
] = PHY_M_P_SYM_MD_X
,
294 [FC_NONE
] = PHY_M_P_NO_PAUSE_X
,
297 /* flow control to GMA disable bits */
298 static const u16 gm_fc_disable
[] = {
299 [FC_NONE
] = GM_GPCR_FC_RX_DIS
| GM_GPCR_FC_TX_DIS
,
300 [FC_TX
] = GM_GPCR_FC_RX_DIS
,
301 [FC_RX
] = GM_GPCR_FC_TX_DIS
,
306 static void sky2_phy_init(struct sky2_hw
*hw
, unsigned port
)
308 struct sky2_port
*sky2
= netdev_priv(hw
->dev
[port
]);
309 u16 ctrl
, ct1000
, adv
, pg
, ledctrl
, ledover
, reg
;
311 if (sky2
->autoneg
== AUTONEG_ENABLE
312 && !(hw
->chip_id
== CHIP_ID_YUKON_XL
313 || hw
->chip_id
== CHIP_ID_YUKON_EC_U
314 || hw
->chip_id
== CHIP_ID_YUKON_EX
)) {
315 u16 ectrl
= gm_phy_read(hw
, port
, PHY_MARV_EXT_CTRL
);
317 ectrl
&= ~(PHY_M_EC_M_DSC_MSK
| PHY_M_EC_S_DSC_MSK
|
319 ectrl
|= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ
);
321 /* on PHY 88E1040 Rev.D0 (and newer) downshift control changed */
322 if (hw
->chip_id
== CHIP_ID_YUKON_EC
)
323 /* set downshift counter to 3x and enable downshift */
324 ectrl
|= PHY_M_EC_DSC_2(2) | PHY_M_EC_DOWN_S_ENA
;
326 /* set master & slave downshift counter to 1x */
327 ectrl
|= PHY_M_EC_M_DSC(0) | PHY_M_EC_S_DSC(1);
329 gm_phy_write(hw
, port
, PHY_MARV_EXT_CTRL
, ectrl
);
332 ctrl
= gm_phy_read(hw
, port
, PHY_MARV_PHY_CTRL
);
333 if (sky2_is_copper(hw
)) {
334 if (hw
->chip_id
== CHIP_ID_YUKON_FE
) {
335 /* enable automatic crossover */
336 ctrl
|= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO
) >> 1;
338 /* disable energy detect */
339 ctrl
&= ~PHY_M_PC_EN_DET_MSK
;
341 /* enable automatic crossover */
342 ctrl
|= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO
);
344 /* downshift on PHY 88E1112 and 88E1149 is changed */
345 if (sky2
->autoneg
== AUTONEG_ENABLE
346 && (hw
->chip_id
== CHIP_ID_YUKON_XL
347 || hw
->chip_id
== CHIP_ID_YUKON_EC_U
348 || hw
->chip_id
== CHIP_ID_YUKON_EX
)) {
349 /* set downshift counter to 3x and enable downshift */
350 ctrl
&= ~PHY_M_PC_DSC_MSK
;
351 ctrl
|= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA
;
355 /* workaround for deviation #4.88 (CRC errors) */
356 /* disable Automatic Crossover */
358 ctrl
&= ~PHY_M_PC_MDIX_MSK
;
361 gm_phy_write(hw
, port
, PHY_MARV_PHY_CTRL
, ctrl
);
363 /* special setup for PHY 88E1112 Fiber */
364 if (hw
->chip_id
== CHIP_ID_YUKON_XL
&& !sky2_is_copper(hw
)) {
365 pg
= gm_phy_read(hw
, port
, PHY_MARV_EXT_ADR
);
367 /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */
368 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, 2);
369 ctrl
= gm_phy_read(hw
, port
, PHY_MARV_PHY_CTRL
);
370 ctrl
&= ~PHY_M_MAC_MD_MSK
;
371 ctrl
|= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX
);
372 gm_phy_write(hw
, port
, PHY_MARV_PHY_CTRL
, ctrl
);
374 if (hw
->pmd_type
== 'P') {
375 /* select page 1 to access Fiber registers */
376 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, 1);
378 /* for SFP-module set SIGDET polarity to low */
379 ctrl
= gm_phy_read(hw
, port
, PHY_MARV_PHY_CTRL
);
380 ctrl
|= PHY_M_FIB_SIGD_POL
;
381 gm_phy_write(hw
, port
, PHY_MARV_PHY_CTRL
, ctrl
);
384 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, pg
);
392 if (sky2
->autoneg
== AUTONEG_ENABLE
) {
393 if (sky2_is_copper(hw
)) {
394 if (sky2
->advertising
& ADVERTISED_1000baseT_Full
)
395 ct1000
|= PHY_M_1000C_AFD
;
396 if (sky2
->advertising
& ADVERTISED_1000baseT_Half
)
397 ct1000
|= PHY_M_1000C_AHD
;
398 if (sky2
->advertising
& ADVERTISED_100baseT_Full
)
399 adv
|= PHY_M_AN_100_FD
;
400 if (sky2
->advertising
& ADVERTISED_100baseT_Half
)
401 adv
|= PHY_M_AN_100_HD
;
402 if (sky2
->advertising
& ADVERTISED_10baseT_Full
)
403 adv
|= PHY_M_AN_10_FD
;
404 if (sky2
->advertising
& ADVERTISED_10baseT_Half
)
405 adv
|= PHY_M_AN_10_HD
;
407 adv
|= copper_fc_adv
[sky2
->flow_mode
];
408 } else { /* special defines for FIBER (88E1040S only) */
409 if (sky2
->advertising
& ADVERTISED_1000baseT_Full
)
410 adv
|= PHY_M_AN_1000X_AFD
;
411 if (sky2
->advertising
& ADVERTISED_1000baseT_Half
)
412 adv
|= PHY_M_AN_1000X_AHD
;
414 adv
|= fiber_fc_adv
[sky2
->flow_mode
];
417 /* Restart Auto-negotiation */
418 ctrl
|= PHY_CT_ANE
| PHY_CT_RE_CFG
;
420 /* forced speed/duplex settings */
421 ct1000
= PHY_M_1000C_MSE
;
423 /* Disable auto update for duplex flow control and speed */
424 reg
|= GM_GPCR_AU_ALL_DIS
;
426 switch (sky2
->speed
) {
428 ctrl
|= PHY_CT_SP1000
;
429 reg
|= GM_GPCR_SPEED_1000
;
432 ctrl
|= PHY_CT_SP100
;
433 reg
|= GM_GPCR_SPEED_100
;
437 if (sky2
->duplex
== DUPLEX_FULL
) {
438 reg
|= GM_GPCR_DUP_FULL
;
439 ctrl
|= PHY_CT_DUP_MD
;
440 } else if (sky2
->speed
< SPEED_1000
)
441 sky2
->flow_mode
= FC_NONE
;
444 reg
|= gm_fc_disable
[sky2
->flow_mode
];
446 /* Forward pause packets to GMAC? */
447 if (sky2
->flow_mode
& FC_RX
)
448 sky2_write8(hw
, SK_REG(port
, GMAC_CTRL
), GMC_PAUSE_ON
);
450 sky2_write8(hw
, SK_REG(port
, GMAC_CTRL
), GMC_PAUSE_OFF
);
453 gma_write16(hw
, port
, GM_GP_CTRL
, reg
);
455 if (hw
->chip_id
!= CHIP_ID_YUKON_FE
)
456 gm_phy_write(hw
, port
, PHY_MARV_1000T_CTRL
, ct1000
);
458 gm_phy_write(hw
, port
, PHY_MARV_AUNE_ADV
, adv
);
459 gm_phy_write(hw
, port
, PHY_MARV_CTRL
, ctrl
);
461 /* Setup Phy LED's */
462 ledctrl
= PHY_M_LED_PULS_DUR(PULS_170MS
);
465 switch (hw
->chip_id
) {
466 case CHIP_ID_YUKON_FE
:
467 /* on 88E3082 these bits are at 11..9 (shifted left) */
468 ledctrl
|= PHY_M_LED_BLINK_RT(BLINK_84MS
) << 1;
470 ctrl
= gm_phy_read(hw
, port
, PHY_MARV_FE_LED_PAR
);
472 /* delete ACT LED control bits */
473 ctrl
&= ~PHY_M_FELP_LED1_MSK
;
474 /* change ACT LED control to blink mode */
475 ctrl
|= PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_ACT_BL
);
476 gm_phy_write(hw
, port
, PHY_MARV_FE_LED_PAR
, ctrl
);
479 case CHIP_ID_YUKON_XL
:
480 pg
= gm_phy_read(hw
, port
, PHY_MARV_EXT_ADR
);
482 /* select page 3 to access LED control register */
483 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, 3);
485 /* set LED Function Control register */
486 gm_phy_write(hw
, port
, PHY_MARV_PHY_CTRL
,
487 (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
488 PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */
489 PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */
490 PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */
492 /* set Polarity Control register */
493 gm_phy_write(hw
, port
, PHY_MARV_PHY_STAT
,
494 (PHY_M_POLC_LS1_P_MIX(4) |
495 PHY_M_POLC_IS0_P_MIX(4) |
496 PHY_M_POLC_LOS_CTRL(2) |
497 PHY_M_POLC_INIT_CTRL(2) |
498 PHY_M_POLC_STA1_CTRL(2) |
499 PHY_M_POLC_STA0_CTRL(2)));
501 /* restore page register */
502 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, pg
);
505 case CHIP_ID_YUKON_EC_U
:
506 case CHIP_ID_YUKON_EX
:
507 pg
= gm_phy_read(hw
, port
, PHY_MARV_EXT_ADR
);
509 /* select page 3 to access LED control register */
510 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, 3);
512 /* set LED Function Control register */
513 gm_phy_write(hw
, port
, PHY_MARV_PHY_CTRL
,
514 (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
515 PHY_M_LEDC_INIT_CTRL(8) | /* 10 Mbps */
516 PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */
517 PHY_M_LEDC_STA0_CTRL(7)));/* 1000 Mbps */
519 /* set Blink Rate in LED Timer Control Register */
520 gm_phy_write(hw
, port
, PHY_MARV_INT_MASK
,
521 ledctrl
| PHY_M_LED_BLINK_RT(BLINK_84MS
));
522 /* restore page register */
523 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, pg
);
527 /* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */
528 ledctrl
|= PHY_M_LED_BLINK_RT(BLINK_84MS
) | PHY_M_LEDC_TX_CTRL
;
529 /* turn off the Rx LED (LED_RX) */
530 ledover
&= ~PHY_M_LED_MO_RX
;
533 if (hw
->chip_id
== CHIP_ID_YUKON_EC_U
&&
534 hw
->chip_rev
== CHIP_REV_YU_EC_U_A1
) {
535 /* apply fixes in PHY AFE */
536 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, 255);
538 /* increase differential signal amplitude in 10BASE-T */
539 gm_phy_write(hw
, port
, 0x18, 0xaa99);
540 gm_phy_write(hw
, port
, 0x17, 0x2011);
542 /* fix for IEEE A/B Symmetry failure in 1000BASE-T */
543 gm_phy_write(hw
, port
, 0x18, 0xa204);
544 gm_phy_write(hw
, port
, 0x17, 0x2002);
546 /* set page register to 0 */
547 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, 0);
548 } else if (hw
->chip_id
!= CHIP_ID_YUKON_EX
) {
549 gm_phy_write(hw
, port
, PHY_MARV_LED_CTRL
, ledctrl
);
551 if (sky2
->autoneg
== AUTONEG_DISABLE
|| sky2
->speed
== SPEED_100
) {
552 /* turn on 100 Mbps LED (LED_LINK100) */
553 ledover
|= PHY_M_LED_MO_100
;
557 gm_phy_write(hw
, port
, PHY_MARV_LED_OVER
, ledover
);
561 /* Enable phy interrupt on auto-negotiation complete (or link up) */
562 if (sky2
->autoneg
== AUTONEG_ENABLE
)
563 gm_phy_write(hw
, port
, PHY_MARV_INT_MASK
, PHY_M_IS_AN_COMPL
);
565 gm_phy_write(hw
, port
, PHY_MARV_INT_MASK
, PHY_M_DEF_MSK
);
568 static void sky2_phy_power(struct sky2_hw
*hw
, unsigned port
, int onoff
)
571 static const u32 phy_power
[]
572 = { PCI_Y2_PHY1_POWD
, PCI_Y2_PHY2_POWD
};
574 /* looks like this XL is back asswards .. */
575 if (hw
->chip_id
== CHIP_ID_YUKON_XL
&& hw
->chip_rev
> 1)
578 sky2_write8(hw
, B2_TST_CTRL1
, TST_CFG_WRITE_ON
);
579 reg1
= sky2_pci_read32(hw
, PCI_DEV_REG1
);
581 /* Turn off phy power saving */
582 reg1
&= ~phy_power
[port
];
584 reg1
|= phy_power
[port
];
586 sky2_pci_write32(hw
, PCI_DEV_REG1
, reg1
);
587 sky2_pci_read32(hw
, PCI_DEV_REG1
);
588 sky2_write8(hw
, B2_TST_CTRL1
, TST_CFG_WRITE_OFF
);
592 /* Force a renegotiation */
593 static void sky2_phy_reinit(struct sky2_port
*sky2
)
595 spin_lock_bh(&sky2
->phy_lock
);
596 sky2_phy_init(sky2
->hw
, sky2
->port
);
597 spin_unlock_bh(&sky2
->phy_lock
);
600 /* Put device in state to listen for Wake On Lan */
601 static void sky2_wol_init(struct sky2_port
*sky2
)
603 struct sky2_hw
*hw
= sky2
->hw
;
604 unsigned port
= sky2
->port
;
605 enum flow_control save_mode
;
609 /* Bring hardware out of reset */
610 sky2_write16(hw
, B0_CTST
, CS_RST_CLR
);
611 sky2_write16(hw
, SK_REG(port
, GMAC_LINK_CTRL
), GMLC_RST_CLR
);
613 sky2_write8(hw
, SK_REG(port
, GPHY_CTRL
), GPC_RST_CLR
);
614 sky2_write8(hw
, SK_REG(port
, GMAC_CTRL
), GMC_RST_CLR
);
617 * sky2_reset will re-enable on resume
619 save_mode
= sky2
->flow_mode
;
620 ctrl
= sky2
->advertising
;
622 sky2
->advertising
&= ~(ADVERTISED_1000baseT_Half
|ADVERTISED_1000baseT_Full
);
623 sky2
->flow_mode
= FC_NONE
;
624 sky2_phy_power(hw
, port
, 1);
625 sky2_phy_reinit(sky2
);
627 sky2
->flow_mode
= save_mode
;
628 sky2
->advertising
= ctrl
;
630 /* Set GMAC to no flow control and auto update for speed/duplex */
631 gma_write16(hw
, port
, GM_GP_CTRL
,
632 GM_GPCR_FC_TX_DIS
|GM_GPCR_TX_ENA
|GM_GPCR_RX_ENA
|
633 GM_GPCR_DUP_FULL
|GM_GPCR_FC_RX_DIS
|GM_GPCR_AU_FCT_DIS
);
635 /* Set WOL address */
636 memcpy_toio(hw
->regs
+ WOL_REGS(port
, WOL_MAC_ADDR
),
637 sky2
->netdev
->dev_addr
, ETH_ALEN
);
639 /* Turn on appropriate WOL control bits */
640 sky2_write16(hw
, WOL_REGS(port
, WOL_CTRL_STAT
), WOL_CTL_CLEAR_RESULT
);
642 if (sky2
->wol
& WAKE_PHY
)
643 ctrl
|= WOL_CTL_ENA_PME_ON_LINK_CHG
|WOL_CTL_ENA_LINK_CHG_UNIT
;
645 ctrl
|= WOL_CTL_DIS_PME_ON_LINK_CHG
|WOL_CTL_DIS_LINK_CHG_UNIT
;
647 if (sky2
->wol
& WAKE_MAGIC
)
648 ctrl
|= WOL_CTL_ENA_PME_ON_MAGIC_PKT
|WOL_CTL_ENA_MAGIC_PKT_UNIT
;
650 ctrl
|= WOL_CTL_DIS_PME_ON_MAGIC_PKT
|WOL_CTL_DIS_MAGIC_PKT_UNIT
;;
652 ctrl
|= WOL_CTL_DIS_PME_ON_PATTERN
|WOL_CTL_DIS_PATTERN_UNIT
;
653 sky2_write16(hw
, WOL_REGS(port
, WOL_CTRL_STAT
), ctrl
);
655 /* Turn on legacy PCI-Express PME mode */
656 sky2_write8(hw
, B2_TST_CTRL1
, TST_CFG_WRITE_ON
);
657 reg1
= sky2_pci_read32(hw
, PCI_DEV_REG1
);
658 reg1
|= PCI_Y2_PME_LEGACY
;
659 sky2_pci_write32(hw
, PCI_DEV_REG1
, reg1
);
660 sky2_write8(hw
, B2_TST_CTRL1
, TST_CFG_WRITE_OFF
);
663 sky2_write8(hw
, SK_REG(port
, RX_GMF_CTRL_T
), GMF_RST_SET
);
667 static void sky2_set_tx_stfwd(struct sky2_hw
*hw
, unsigned port
)
669 if (hw
->chip_id
== CHIP_ID_YUKON_EX
&& hw
->chip_rev
!= CHIP_REV_YU_EX_A0
) {
670 sky2_write32(hw
, SK_REG(port
, TX_GMF_CTRL_T
),
672 (hw
->dev
[port
]->mtu
> ETH_DATA_LEN
) ? TX_JUMBO_ENA
: TX_JUMBO_DIS
);
674 if (hw
->dev
[port
]->mtu
> ETH_DATA_LEN
) {
675 /* set Tx GMAC FIFO Almost Empty Threshold */
676 sky2_write32(hw
, SK_REG(port
, TX_GMF_AE_THR
),
677 (ECU_JUMBO_WM
<< 16) | ECU_AE_THR
);
679 sky2_write32(hw
, SK_REG(port
, TX_GMF_CTRL_T
),
680 TX_JUMBO_ENA
| TX_STFW_DIS
);
682 /* Can't do offload because of lack of store/forward */
683 hw
->dev
[port
]->features
&= ~(NETIF_F_TSO
| NETIF_F_SG
686 sky2_write32(hw
, SK_REG(port
, TX_GMF_CTRL_T
),
687 TX_JUMBO_DIS
| TX_STFW_ENA
);
691 static void sky2_mac_init(struct sky2_hw
*hw
, unsigned port
)
693 struct sky2_port
*sky2
= netdev_priv(hw
->dev
[port
]);
696 const u8
*addr
= hw
->dev
[port
]->dev_addr
;
698 sky2_write32(hw
, SK_REG(port
, GPHY_CTRL
), GPC_RST_SET
);
699 sky2_write32(hw
, SK_REG(port
, GPHY_CTRL
), GPC_RST_CLR
);
701 sky2_write8(hw
, SK_REG(port
, GMAC_CTRL
), GMC_RST_CLR
);
703 if (hw
->chip_id
== CHIP_ID_YUKON_XL
&& hw
->chip_rev
== 0 && port
== 1) {
704 /* WA DEV_472 -- looks like crossed wires on port 2 */
705 /* clear GMAC 1 Control reset */
706 sky2_write8(hw
, SK_REG(0, GMAC_CTRL
), GMC_RST_CLR
);
708 sky2_write8(hw
, SK_REG(1, GMAC_CTRL
), GMC_RST_SET
);
709 sky2_write8(hw
, SK_REG(1, GMAC_CTRL
), GMC_RST_CLR
);
710 } while (gm_phy_read(hw
, 1, PHY_MARV_ID0
) != PHY_MARV_ID0_VAL
||
711 gm_phy_read(hw
, 1, PHY_MARV_ID1
) != PHY_MARV_ID1_Y2
||
712 gm_phy_read(hw
, 1, PHY_MARV_INT_MASK
) != 0);
715 sky2_read16(hw
, SK_REG(port
, GMAC_IRQ_SRC
));
717 /* Enable Transmit FIFO Underrun */
718 sky2_write8(hw
, SK_REG(port
, GMAC_IRQ_MSK
), GMAC_DEF_MSK
);
720 spin_lock_bh(&sky2
->phy_lock
);
721 sky2_phy_init(hw
, port
);
722 spin_unlock_bh(&sky2
->phy_lock
);
725 reg
= gma_read16(hw
, port
, GM_PHY_ADDR
);
726 gma_write16(hw
, port
, GM_PHY_ADDR
, reg
| GM_PAR_MIB_CLR
);
728 for (i
= GM_MIB_CNT_BASE
; i
<= GM_MIB_CNT_END
; i
+= 4)
729 gma_read16(hw
, port
, i
);
730 gma_write16(hw
, port
, GM_PHY_ADDR
, reg
);
732 /* transmit control */
733 gma_write16(hw
, port
, GM_TX_CTRL
, TX_COL_THR(TX_COL_DEF
));
735 /* receive control reg: unicast + multicast + no FCS */
736 gma_write16(hw
, port
, GM_RX_CTRL
,
737 GM_RXCR_UCF_ENA
| GM_RXCR_CRC_DIS
| GM_RXCR_MCF_ENA
);
739 /* transmit flow control */
740 gma_write16(hw
, port
, GM_TX_FLOW_CTRL
, 0xffff);
742 /* transmit parameter */
743 gma_write16(hw
, port
, GM_TX_PARAM
,
744 TX_JAM_LEN_VAL(TX_JAM_LEN_DEF
) |
745 TX_JAM_IPG_VAL(TX_JAM_IPG_DEF
) |
746 TX_IPG_JAM_DATA(TX_IPG_JAM_DEF
) |
747 TX_BACK_OFF_LIM(TX_BOF_LIM_DEF
));
749 /* serial mode register */
750 reg
= DATA_BLIND_VAL(DATA_BLIND_DEF
) |
751 GM_SMOD_VLAN_ENA
| IPG_DATA_VAL(IPG_DATA_DEF
);
753 if (hw
->dev
[port
]->mtu
> ETH_DATA_LEN
)
754 reg
|= GM_SMOD_JUMBO_ENA
;
756 gma_write16(hw
, port
, GM_SERIAL_MODE
, reg
);
758 /* virtual address for data */
759 gma_set_addr(hw
, port
, GM_SRC_ADDR_2L
, addr
);
761 /* physical address: used for pause frames */
762 gma_set_addr(hw
, port
, GM_SRC_ADDR_1L
, addr
);
764 /* ignore counter overflows */
765 gma_write16(hw
, port
, GM_TX_IRQ_MSK
, 0);
766 gma_write16(hw
, port
, GM_RX_IRQ_MSK
, 0);
767 gma_write16(hw
, port
, GM_TR_IRQ_MSK
, 0);
769 /* Configure Rx MAC FIFO */
770 sky2_write8(hw
, SK_REG(port
, RX_GMF_CTRL_T
), GMF_RST_CLR
);
771 reg
= GMF_OPER_ON
| GMF_RX_F_FL_ON
;
772 if (hw
->chip_id
== CHIP_ID_YUKON_EX
)
773 reg
|= GMF_RX_OVER_ON
;
775 sky2_write32(hw
, SK_REG(port
, RX_GMF_CTRL_T
), reg
);
777 /* Flush Rx MAC FIFO on any flow control or error */
778 sky2_write16(hw
, SK_REG(port
, RX_GMF_FL_MSK
), GMR_FS_ANY_ERR
);
780 /* Set threshold to 0xa (64 bytes) + 1 to workaround pause bug */
781 sky2_write16(hw
, SK_REG(port
, RX_GMF_FL_THR
), RX_GMF_FL_THR_DEF
+1);
783 /* Configure Tx MAC FIFO */
784 sky2_write8(hw
, SK_REG(port
, TX_GMF_CTRL_T
), GMF_RST_CLR
);
785 sky2_write16(hw
, SK_REG(port
, TX_GMF_CTRL_T
), GMF_OPER_ON
);
787 if (hw
->chip_id
== CHIP_ID_YUKON_EC_U
|| hw
->chip_id
== CHIP_ID_YUKON_EX
) {
788 sky2_write8(hw
, SK_REG(port
, RX_GMF_LP_THR
), 768/8);
789 sky2_write8(hw
, SK_REG(port
, RX_GMF_UP_THR
), 1024/8);
791 sky2_set_tx_stfwd(hw
, port
);
796 /* Assign Ram Buffer allocation to queue */
797 static void sky2_ramset(struct sky2_hw
*hw
, u16 q
, u32 start
, u32 space
)
801 /* convert from K bytes to qwords used for hw register */
804 end
= start
+ space
- 1;
806 sky2_write8(hw
, RB_ADDR(q
, RB_CTRL
), RB_RST_CLR
);
807 sky2_write32(hw
, RB_ADDR(q
, RB_START
), start
);
808 sky2_write32(hw
, RB_ADDR(q
, RB_END
), end
);
809 sky2_write32(hw
, RB_ADDR(q
, RB_WP
), start
);
810 sky2_write32(hw
, RB_ADDR(q
, RB_RP
), start
);
812 if (q
== Q_R1
|| q
== Q_R2
) {
813 u32 tp
= space
- space
/4;
815 /* On receive queue's set the thresholds
816 * give receiver priority when > 3/4 full
817 * send pause when down to 2K
819 sky2_write32(hw
, RB_ADDR(q
, RB_RX_UTHP
), tp
);
820 sky2_write32(hw
, RB_ADDR(q
, RB_RX_LTHP
), space
/2);
823 sky2_write32(hw
, RB_ADDR(q
, RB_RX_UTPP
), tp
);
824 sky2_write32(hw
, RB_ADDR(q
, RB_RX_LTPP
), space
/4);
826 /* Enable store & forward on Tx queue's because
827 * Tx FIFO is only 1K on Yukon
829 sky2_write8(hw
, RB_ADDR(q
, RB_CTRL
), RB_ENA_STFWD
);
832 sky2_write8(hw
, RB_ADDR(q
, RB_CTRL
), RB_ENA_OP_MD
);
833 sky2_read8(hw
, RB_ADDR(q
, RB_CTRL
));
836 /* Setup Bus Memory Interface */
837 static void sky2_qset(struct sky2_hw
*hw
, u16 q
)
839 sky2_write32(hw
, Q_ADDR(q
, Q_CSR
), BMU_CLR_RESET
);
840 sky2_write32(hw
, Q_ADDR(q
, Q_CSR
), BMU_OPER_INIT
);
841 sky2_write32(hw
, Q_ADDR(q
, Q_CSR
), BMU_FIFO_OP_ON
);
842 sky2_write32(hw
, Q_ADDR(q
, Q_WM
), BMU_WM_DEFAULT
);
845 /* Setup prefetch unit registers. This is the interface between
846 * hardware and driver list elements
848 static void sky2_prefetch_init(struct sky2_hw
*hw
, u32 qaddr
,
851 sky2_write32(hw
, Y2_QADDR(qaddr
, PREF_UNIT_CTRL
), PREF_UNIT_RST_SET
);
852 sky2_write32(hw
, Y2_QADDR(qaddr
, PREF_UNIT_CTRL
), PREF_UNIT_RST_CLR
);
853 sky2_write32(hw
, Y2_QADDR(qaddr
, PREF_UNIT_ADDR_HI
), addr
>> 32);
854 sky2_write32(hw
, Y2_QADDR(qaddr
, PREF_UNIT_ADDR_LO
), (u32
) addr
);
855 sky2_write16(hw
, Y2_QADDR(qaddr
, PREF_UNIT_LAST_IDX
), last
);
856 sky2_write32(hw
, Y2_QADDR(qaddr
, PREF_UNIT_CTRL
), PREF_UNIT_OP_ON
);
858 sky2_read32(hw
, Y2_QADDR(qaddr
, PREF_UNIT_CTRL
));
861 static inline struct sky2_tx_le
*get_tx_le(struct sky2_port
*sky2
)
863 struct sky2_tx_le
*le
= sky2
->tx_le
+ sky2
->tx_prod
;
865 sky2
->tx_prod
= RING_NEXT(sky2
->tx_prod
, TX_RING_SIZE
);
870 static inline struct tx_ring_info
*tx_le_re(struct sky2_port
*sky2
,
871 struct sky2_tx_le
*le
)
873 return sky2
->tx_ring
+ (le
- sky2
->tx_le
);
876 /* Update chip's next pointer */
877 static inline void sky2_put_idx(struct sky2_hw
*hw
, unsigned q
, u16 idx
)
879 /* Make sure write' to descriptors are complete before we tell hardware */
881 sky2_write16(hw
, Y2_QADDR(q
, PREF_UNIT_PUT_IDX
), idx
);
883 /* Synchronize I/O on since next processor may write to tail */
888 static inline struct sky2_rx_le
*sky2_next_rx(struct sky2_port
*sky2
)
890 struct sky2_rx_le
*le
= sky2
->rx_le
+ sky2
->rx_put
;
891 sky2
->rx_put
= RING_NEXT(sky2
->rx_put
, RX_LE_SIZE
);
896 /* Return high part of DMA address (could be 32 or 64 bit) */
897 static inline u32
high32(dma_addr_t a
)
899 return sizeof(a
) > sizeof(u32
) ? (a
>> 16) >> 16 : 0;
902 /* Build description to hardware for one receive segment */
903 static void sky2_rx_add(struct sky2_port
*sky2
, u8 op
,
904 dma_addr_t map
, unsigned len
)
906 struct sky2_rx_le
*le
;
907 u32 hi
= high32(map
);
909 if (sky2
->rx_addr64
!= hi
) {
910 le
= sky2_next_rx(sky2
);
911 le
->addr
= cpu_to_le32(hi
);
912 le
->opcode
= OP_ADDR64
| HW_OWNER
;
913 sky2
->rx_addr64
= high32(map
+ len
);
916 le
= sky2_next_rx(sky2
);
917 le
->addr
= cpu_to_le32((u32
) map
);
918 le
->length
= cpu_to_le16(len
);
919 le
->opcode
= op
| HW_OWNER
;
922 /* Build description to hardware for one possibly fragmented skb */
923 static void sky2_rx_submit(struct sky2_port
*sky2
,
924 const struct rx_ring_info
*re
)
928 sky2_rx_add(sky2
, OP_PACKET
, re
->data_addr
, sky2
->rx_data_size
);
930 for (i
= 0; i
< skb_shinfo(re
->skb
)->nr_frags
; i
++)
931 sky2_rx_add(sky2
, OP_BUFFER
, re
->frag_addr
[i
], PAGE_SIZE
);
935 static void sky2_rx_map_skb(struct pci_dev
*pdev
, struct rx_ring_info
*re
,
938 struct sk_buff
*skb
= re
->skb
;
941 re
->data_addr
= pci_map_single(pdev
, skb
->data
, size
, PCI_DMA_FROMDEVICE
);
942 pci_unmap_len_set(re
, data_size
, size
);
944 for (i
= 0; i
< skb_shinfo(skb
)->nr_frags
; i
++)
945 re
->frag_addr
[i
] = pci_map_page(pdev
,
946 skb_shinfo(skb
)->frags
[i
].page
,
947 skb_shinfo(skb
)->frags
[i
].page_offset
,
948 skb_shinfo(skb
)->frags
[i
].size
,
952 static void sky2_rx_unmap_skb(struct pci_dev
*pdev
, struct rx_ring_info
*re
)
954 struct sk_buff
*skb
= re
->skb
;
957 pci_unmap_single(pdev
, re
->data_addr
, pci_unmap_len(re
, data_size
),
960 for (i
= 0; i
< skb_shinfo(skb
)->nr_frags
; i
++)
961 pci_unmap_page(pdev
, re
->frag_addr
[i
],
962 skb_shinfo(skb
)->frags
[i
].size
,
966 /* Tell chip where to start receive checksum.
967 * Actually has two checksums, but set both same to avoid possible byte
970 static void rx_set_checksum(struct sky2_port
*sky2
)
972 struct sky2_rx_le
*le
;
974 if (sky2
->hw
->chip_id
!= CHIP_ID_YUKON_EX
) {
975 le
= sky2_next_rx(sky2
);
976 le
->addr
= cpu_to_le32((ETH_HLEN
<< 16) | ETH_HLEN
);
978 le
->opcode
= OP_TCPSTART
| HW_OWNER
;
980 sky2_write32(sky2
->hw
,
981 Q_ADDR(rxqaddr
[sky2
->port
], Q_CSR
),
982 sky2
->rx_csum
? BMU_ENA_RX_CHKSUM
: BMU_DIS_RX_CHKSUM
);
988 * The RX Stop command will not work for Yukon-2 if the BMU does not
989 * reach the end of packet and since we can't make sure that we have
990 * incoming data, we must reset the BMU while it is not doing a DMA
991 * transfer. Since it is possible that the RX path is still active,
992 * the RX RAM buffer will be stopped first, so any possible incoming
993 * data will not trigger a DMA. After the RAM buffer is stopped, the
994 * BMU is polled until any DMA in progress is ended and only then it
997 static void sky2_rx_stop(struct sky2_port
*sky2
)
999 struct sky2_hw
*hw
= sky2
->hw
;
1000 unsigned rxq
= rxqaddr
[sky2
->port
];
1003 /* disable the RAM Buffer receive queue */
1004 sky2_write8(hw
, RB_ADDR(rxq
, RB_CTRL
), RB_DIS_OP_MD
);
1006 for (i
= 0; i
< 0xffff; i
++)
1007 if (sky2_read8(hw
, RB_ADDR(rxq
, Q_RSL
))
1008 == sky2_read8(hw
, RB_ADDR(rxq
, Q_RL
)))
1011 printk(KERN_WARNING PFX
"%s: receiver stop failed\n",
1012 sky2
->netdev
->name
);
1014 sky2_write32(hw
, Q_ADDR(rxq
, Q_CSR
), BMU_RST_SET
| BMU_FIFO_RST
);
1016 /* reset the Rx prefetch unit */
1017 sky2_write32(hw
, Y2_QADDR(rxq
, PREF_UNIT_CTRL
), PREF_UNIT_RST_SET
);
1021 /* Clean out receive buffer area, assumes receiver hardware stopped */
1022 static void sky2_rx_clean(struct sky2_port
*sky2
)
1026 memset(sky2
->rx_le
, 0, RX_LE_BYTES
);
1027 for (i
= 0; i
< sky2
->rx_pending
; i
++) {
1028 struct rx_ring_info
*re
= sky2
->rx_ring
+ i
;
1031 sky2_rx_unmap_skb(sky2
->hw
->pdev
, re
);
1038 /* Basic MII support */
1039 static int sky2_ioctl(struct net_device
*dev
, struct ifreq
*ifr
, int cmd
)
1041 struct mii_ioctl_data
*data
= if_mii(ifr
);
1042 struct sky2_port
*sky2
= netdev_priv(dev
);
1043 struct sky2_hw
*hw
= sky2
->hw
;
1044 int err
= -EOPNOTSUPP
;
1046 if (!netif_running(dev
))
1047 return -ENODEV
; /* Phy still in reset */
1051 data
->phy_id
= PHY_ADDR_MARV
;
1057 spin_lock_bh(&sky2
->phy_lock
);
1058 err
= __gm_phy_read(hw
, sky2
->port
, data
->reg_num
& 0x1f, &val
);
1059 spin_unlock_bh(&sky2
->phy_lock
);
1061 data
->val_out
= val
;
1066 if (!capable(CAP_NET_ADMIN
))
1069 spin_lock_bh(&sky2
->phy_lock
);
1070 err
= gm_phy_write(hw
, sky2
->port
, data
->reg_num
& 0x1f,
1072 spin_unlock_bh(&sky2
->phy_lock
);
1078 #ifdef SKY2_VLAN_TAG_USED
1079 static void sky2_vlan_rx_register(struct net_device
*dev
, struct vlan_group
*grp
)
1081 struct sky2_port
*sky2
= netdev_priv(dev
);
1082 struct sky2_hw
*hw
= sky2
->hw
;
1083 u16 port
= sky2
->port
;
1085 netif_tx_lock_bh(dev
);
1086 netif_poll_disable(sky2
->hw
->dev
[0]);
1090 sky2_write32(hw
, SK_REG(port
, RX_GMF_CTRL_T
),
1092 sky2_write32(hw
, SK_REG(port
, TX_GMF_CTRL_T
),
1095 sky2_write32(hw
, SK_REG(port
, RX_GMF_CTRL_T
),
1097 sky2_write32(hw
, SK_REG(port
, TX_GMF_CTRL_T
),
1101 netif_poll_enable(sky2
->hw
->dev
[0]);
1102 netif_tx_unlock_bh(dev
);
1107 * Allocate an skb for receiving. If the MTU is large enough
1108 * make the skb non-linear with a fragment list of pages.
1110 * It appears the hardware has a bug in the FIFO logic that
1111 * cause it to hang if the FIFO gets overrun and the receive buffer
1112 * is not 64 byte aligned. The buffer returned from netdev_alloc_skb is
1113 * aligned except if slab debugging is enabled.
1115 static struct sk_buff
*sky2_rx_alloc(struct sky2_port
*sky2
)
1117 struct sk_buff
*skb
;
1121 skb
= netdev_alloc_skb(sky2
->netdev
, sky2
->rx_data_size
+ RX_SKB_ALIGN
);
1125 p
= (unsigned long) skb
->data
;
1126 skb_reserve(skb
, ALIGN(p
, RX_SKB_ALIGN
) - p
);
1128 for (i
= 0; i
< sky2
->rx_nfrags
; i
++) {
1129 struct page
*page
= alloc_page(GFP_ATOMIC
);
1133 skb_fill_page_desc(skb
, i
, page
, 0, PAGE_SIZE
);
1143 static inline void sky2_rx_update(struct sky2_port
*sky2
, unsigned rxq
)
1145 sky2_put_idx(sky2
->hw
, rxq
, sky2
->rx_put
);
1149 * Allocate and setup receiver buffer pool.
1150 * Normal case this ends up creating one list element for skb
1151 * in the receive ring. Worst case if using large MTU and each
1152 * allocation falls on a different 64 bit region, that results
1153 * in 6 list elements per ring entry.
1154 * One element is used for checksum enable/disable, and one
1155 * extra to avoid wrap.
1157 static int sky2_rx_start(struct sky2_port
*sky2
)
1159 struct sky2_hw
*hw
= sky2
->hw
;
1160 struct rx_ring_info
*re
;
1161 unsigned rxq
= rxqaddr
[sky2
->port
];
1162 unsigned i
, size
, space
, thresh
;
1164 sky2
->rx_put
= sky2
->rx_next
= 0;
1167 /* On PCI express lowering the watermark gives better performance */
1168 if (pci_find_capability(hw
->pdev
, PCI_CAP_ID_EXP
))
1169 sky2_write32(hw
, Q_ADDR(rxq
, Q_WM
), BMU_WM_PEX
);
1171 /* These chips have no ram buffer?
1172 * MAC Rx RAM Read is controlled by hardware */
1173 if (hw
->chip_id
== CHIP_ID_YUKON_EC_U
&&
1174 (hw
->chip_rev
== CHIP_REV_YU_EC_U_A1
1175 || hw
->chip_rev
== CHIP_REV_YU_EC_U_B0
))
1176 sky2_write32(hw
, Q_ADDR(rxq
, Q_TEST
), F_M_RX_RAM_DIS
);
1178 sky2_prefetch_init(hw
, rxq
, sky2
->rx_le_map
, RX_LE_SIZE
- 1);
1180 rx_set_checksum(sky2
);
1182 /* Space needed for frame data + headers rounded up */
1183 size
= ALIGN(sky2
->netdev
->mtu
+ ETH_HLEN
+ VLAN_HLEN
, 8)
1186 /* Stopping point for hardware truncation */
1187 thresh
= (size
- 8) / sizeof(u32
);
1189 /* Account for overhead of skb - to avoid order > 0 allocation */
1190 space
= SKB_DATA_ALIGN(size
) + NET_SKB_PAD
1191 + sizeof(struct skb_shared_info
);
1193 sky2
->rx_nfrags
= space
>> PAGE_SHIFT
;
1194 BUG_ON(sky2
->rx_nfrags
> ARRAY_SIZE(re
->frag_addr
));
1196 if (sky2
->rx_nfrags
!= 0) {
1197 /* Compute residue after pages */
1198 space
= sky2
->rx_nfrags
<< PAGE_SHIFT
;
1205 /* Optimize to handle small packets and headers */
1206 if (size
< copybreak
)
1208 if (size
< ETH_HLEN
)
1211 sky2
->rx_data_size
= size
;
1214 for (i
= 0; i
< sky2
->rx_pending
; i
++) {
1215 re
= sky2
->rx_ring
+ i
;
1217 re
->skb
= sky2_rx_alloc(sky2
);
1221 sky2_rx_map_skb(hw
->pdev
, re
, sky2
->rx_data_size
);
1222 sky2_rx_submit(sky2
, re
);
1226 * The receiver hangs if it receives frames larger than the
1227 * packet buffer. As a workaround, truncate oversize frames, but
1228 * the register is limited to 9 bits, so if you do frames > 2052
1229 * you better get the MTU right!
1232 sky2_write32(hw
, SK_REG(sky2
->port
, RX_GMF_CTRL_T
), RX_TRUNC_OFF
);
1234 sky2_write16(hw
, SK_REG(sky2
->port
, RX_GMF_TR_THR
), thresh
);
1235 sky2_write32(hw
, SK_REG(sky2
->port
, RX_GMF_CTRL_T
), RX_TRUNC_ON
);
1238 /* Tell chip about available buffers */
1239 sky2_rx_update(sky2
, rxq
);
1242 sky2_rx_clean(sky2
);
1246 /* Bring up network interface. */
1247 static int sky2_up(struct net_device
*dev
)
1249 struct sky2_port
*sky2
= netdev_priv(dev
);
1250 struct sky2_hw
*hw
= sky2
->hw
;
1251 unsigned port
= sky2
->port
;
1253 int cap
, err
= -ENOMEM
;
1254 struct net_device
*otherdev
= hw
->dev
[sky2
->port
^1];
1257 * On dual port PCI-X card, there is an problem where status
1258 * can be received out of order due to split transactions
1260 if (otherdev
&& netif_running(otherdev
) &&
1261 (cap
= pci_find_capability(hw
->pdev
, PCI_CAP_ID_PCIX
))) {
1262 struct sky2_port
*osky2
= netdev_priv(otherdev
);
1265 cmd
= sky2_pci_read16(hw
, cap
+ PCI_X_CMD
);
1266 cmd
&= ~PCI_X_CMD_MAX_SPLIT
;
1267 sky2_pci_write16(hw
, cap
+ PCI_X_CMD
, cmd
);
1273 if (netif_msg_ifup(sky2
))
1274 printk(KERN_INFO PFX
"%s: enabling interface\n", dev
->name
);
1276 netif_carrier_off(dev
);
1278 /* must be power of 2 */
1279 sky2
->tx_le
= pci_alloc_consistent(hw
->pdev
,
1281 sizeof(struct sky2_tx_le
),
1286 sky2
->tx_ring
= kcalloc(TX_RING_SIZE
, sizeof(struct tx_ring_info
),
1290 sky2
->tx_prod
= sky2
->tx_cons
= 0;
1292 sky2
->rx_le
= pci_alloc_consistent(hw
->pdev
, RX_LE_BYTES
,
1296 memset(sky2
->rx_le
, 0, RX_LE_BYTES
);
1298 sky2
->rx_ring
= kcalloc(sky2
->rx_pending
, sizeof(struct rx_ring_info
),
1303 sky2_phy_power(hw
, port
, 1);
1305 sky2_mac_init(hw
, port
);
1307 /* Register is number of 4K blocks on internal RAM buffer. */
1308 ramsize
= sky2_read8(hw
, B2_E_0
) * 4;
1309 printk(KERN_INFO PFX
"%s: ram buffer %dK\n", dev
->name
, ramsize
);
1315 rxspace
= ramsize
/ 2;
1317 rxspace
= 8 + (2*(ramsize
- 16))/3;
1319 sky2_ramset(hw
, rxqaddr
[port
], 0, rxspace
);
1320 sky2_ramset(hw
, txqaddr
[port
], rxspace
, ramsize
- rxspace
);
1322 /* Make sure SyncQ is disabled */
1323 sky2_write8(hw
, RB_ADDR(port
== 0 ? Q_XS1
: Q_XS2
, RB_CTRL
),
1327 sky2_qset(hw
, txqaddr
[port
]);
1329 /* This is copied from sk98lin 10.0.5.3; no one tells me about erratta's */
1330 if (hw
->chip_id
== CHIP_ID_YUKON_EX
&& hw
->chip_rev
== CHIP_REV_YU_EX_B0
)
1331 sky2_write32(hw
, Q_ADDR(txqaddr
[port
], Q_TEST
), F_TX_CHK_AUTO_OFF
);
1333 /* Set almost empty threshold */
1334 if (hw
->chip_id
== CHIP_ID_YUKON_EC_U
1335 && hw
->chip_rev
== CHIP_REV_YU_EC_U_A0
)
1336 sky2_write16(hw
, Q_ADDR(txqaddr
[port
], Q_AL
), ECU_TXFF_LEV
);
1338 sky2_prefetch_init(hw
, txqaddr
[port
], sky2
->tx_le_map
,
1341 err
= sky2_rx_start(sky2
);
1345 /* Enable interrupts from phy/mac for port */
1346 imask
= sky2_read32(hw
, B0_IMSK
);
1347 imask
|= portirq_msk
[port
];
1348 sky2_write32(hw
, B0_IMSK
, imask
);
1354 pci_free_consistent(hw
->pdev
, RX_LE_BYTES
,
1355 sky2
->rx_le
, sky2
->rx_le_map
);
1359 pci_free_consistent(hw
->pdev
,
1360 TX_RING_SIZE
* sizeof(struct sky2_tx_le
),
1361 sky2
->tx_le
, sky2
->tx_le_map
);
1364 kfree(sky2
->tx_ring
);
1365 kfree(sky2
->rx_ring
);
1367 sky2
->tx_ring
= NULL
;
1368 sky2
->rx_ring
= NULL
;
1372 /* Modular subtraction in ring */
1373 static inline int tx_dist(unsigned tail
, unsigned head
)
1375 return (head
- tail
) & (TX_RING_SIZE
- 1);
1378 /* Number of list elements available for next tx */
1379 static inline int tx_avail(const struct sky2_port
*sky2
)
1381 return sky2
->tx_pending
- tx_dist(sky2
->tx_cons
, sky2
->tx_prod
);
1384 /* Estimate of number of transmit list elements required */
1385 static unsigned tx_le_req(const struct sk_buff
*skb
)
1389 count
= sizeof(dma_addr_t
) / sizeof(u32
);
1390 count
+= skb_shinfo(skb
)->nr_frags
* count
;
1392 if (skb_is_gso(skb
))
1395 if (skb
->ip_summed
== CHECKSUM_PARTIAL
)
1402 * Put one packet in ring for transmit.
1403 * A single packet can generate multiple list elements, and
1404 * the number of ring elements will probably be less than the number
1405 * of list elements used.
1407 static int sky2_xmit_frame(struct sk_buff
*skb
, struct net_device
*dev
)
1409 struct sky2_port
*sky2
= netdev_priv(dev
);
1410 struct sky2_hw
*hw
= sky2
->hw
;
1411 struct sky2_tx_le
*le
= NULL
;
1412 struct tx_ring_info
*re
;
1419 if (unlikely(tx_avail(sky2
) < tx_le_req(skb
)))
1420 return NETDEV_TX_BUSY
;
1422 if (unlikely(netif_msg_tx_queued(sky2
)))
1423 printk(KERN_DEBUG
"%s: tx queued, slot %u, len %d\n",
1424 dev
->name
, sky2
->tx_prod
, skb
->len
);
1426 len
= skb_headlen(skb
);
1427 mapping
= pci_map_single(hw
->pdev
, skb
->data
, len
, PCI_DMA_TODEVICE
);
1428 addr64
= high32(mapping
);
1430 /* Send high bits if changed or crosses boundary */
1431 if (addr64
!= sky2
->tx_addr64
|| high32(mapping
+ len
) != sky2
->tx_addr64
) {
1432 le
= get_tx_le(sky2
);
1433 le
->addr
= cpu_to_le32(addr64
);
1434 le
->opcode
= OP_ADDR64
| HW_OWNER
;
1435 sky2
->tx_addr64
= high32(mapping
+ len
);
1438 /* Check for TCP Segmentation Offload */
1439 mss
= skb_shinfo(skb
)->gso_size
;
1441 if (hw
->chip_id
!= CHIP_ID_YUKON_EX
)
1442 mss
+= ETH_HLEN
+ ip_hdrlen(skb
) + tcp_hdrlen(skb
);
1444 if (mss
!= sky2
->tx_last_mss
) {
1445 le
= get_tx_le(sky2
);
1446 le
->addr
= cpu_to_le32(mss
);
1447 if (hw
->chip_id
== CHIP_ID_YUKON_EX
)
1448 le
->opcode
= OP_MSS
| HW_OWNER
;
1450 le
->opcode
= OP_LRGLEN
| HW_OWNER
;
1451 sky2
->tx_last_mss
= mss
;
1456 #ifdef SKY2_VLAN_TAG_USED
1457 /* Add VLAN tag, can piggyback on LRGLEN or ADDR64 */
1458 if (sky2
->vlgrp
&& vlan_tx_tag_present(skb
)) {
1460 le
= get_tx_le(sky2
);
1462 le
->opcode
= OP_VLAN
|HW_OWNER
;
1464 le
->opcode
|= OP_VLAN
;
1465 le
->length
= cpu_to_be16(vlan_tx_tag_get(skb
));
1470 /* Handle TCP checksum offload */
1471 if (skb
->ip_summed
== CHECKSUM_PARTIAL
) {
1472 /* On Yukon EX (some versions) encoding change. */
1473 if (hw
->chip_id
== CHIP_ID_YUKON_EX
1474 && hw
->chip_rev
!= CHIP_REV_YU_EX_B0
)
1475 ctrl
|= CALSUM
; /* auto checksum */
1477 const unsigned offset
= skb_transport_offset(skb
);
1480 tcpsum
= offset
<< 16; /* sum start */
1481 tcpsum
|= offset
+ skb
->csum_offset
; /* sum write */
1483 ctrl
|= CALSUM
| WR_SUM
| INIT_SUM
| LOCK_SUM
;
1484 if (ip_hdr(skb
)->protocol
== IPPROTO_UDP
)
1487 if (tcpsum
!= sky2
->tx_tcpsum
) {
1488 sky2
->tx_tcpsum
= tcpsum
;
1490 le
= get_tx_le(sky2
);
1491 le
->addr
= cpu_to_le32(tcpsum
);
1492 le
->length
= 0; /* initial checksum value */
1493 le
->ctrl
= 1; /* one packet */
1494 le
->opcode
= OP_TCPLISW
| HW_OWNER
;
1499 le
= get_tx_le(sky2
);
1500 le
->addr
= cpu_to_le32((u32
) mapping
);
1501 le
->length
= cpu_to_le16(len
);
1503 le
->opcode
= mss
? (OP_LARGESEND
| HW_OWNER
) : (OP_PACKET
| HW_OWNER
);
1505 re
= tx_le_re(sky2
, le
);
1507 pci_unmap_addr_set(re
, mapaddr
, mapping
);
1508 pci_unmap_len_set(re
, maplen
, len
);
1510 for (i
= 0; i
< skb_shinfo(skb
)->nr_frags
; i
++) {
1511 const skb_frag_t
*frag
= &skb_shinfo(skb
)->frags
[i
];
1513 mapping
= pci_map_page(hw
->pdev
, frag
->page
, frag
->page_offset
,
1514 frag
->size
, PCI_DMA_TODEVICE
);
1515 addr64
= high32(mapping
);
1516 if (addr64
!= sky2
->tx_addr64
) {
1517 le
= get_tx_le(sky2
);
1518 le
->addr
= cpu_to_le32(addr64
);
1520 le
->opcode
= OP_ADDR64
| HW_OWNER
;
1521 sky2
->tx_addr64
= addr64
;
1524 le
= get_tx_le(sky2
);
1525 le
->addr
= cpu_to_le32((u32
) mapping
);
1526 le
->length
= cpu_to_le16(frag
->size
);
1528 le
->opcode
= OP_BUFFER
| HW_OWNER
;
1530 re
= tx_le_re(sky2
, le
);
1532 pci_unmap_addr_set(re
, mapaddr
, mapping
);
1533 pci_unmap_len_set(re
, maplen
, frag
->size
);
1538 if (tx_avail(sky2
) <= MAX_SKB_TX_LE
)
1539 netif_stop_queue(dev
);
1541 sky2_put_idx(hw
, txqaddr
[sky2
->port
], sky2
->tx_prod
);
1543 dev
->trans_start
= jiffies
;
1544 return NETDEV_TX_OK
;
1548 * Free ring elements from starting at tx_cons until "done"
1550 * NB: the hardware will tell us about partial completion of multi-part
1551 * buffers so make sure not to free skb to early.
1553 static void sky2_tx_complete(struct sky2_port
*sky2
, u16 done
)
1555 struct net_device
*dev
= sky2
->netdev
;
1556 struct pci_dev
*pdev
= sky2
->hw
->pdev
;
1559 BUG_ON(done
>= TX_RING_SIZE
);
1561 for (idx
= sky2
->tx_cons
; idx
!= done
;
1562 idx
= RING_NEXT(idx
, TX_RING_SIZE
)) {
1563 struct sky2_tx_le
*le
= sky2
->tx_le
+ idx
;
1564 struct tx_ring_info
*re
= sky2
->tx_ring
+ idx
;
1566 switch(le
->opcode
& ~HW_OWNER
) {
1569 pci_unmap_single(pdev
,
1570 pci_unmap_addr(re
, mapaddr
),
1571 pci_unmap_len(re
, maplen
),
1575 pci_unmap_page(pdev
, pci_unmap_addr(re
, mapaddr
),
1576 pci_unmap_len(re
, maplen
),
1581 if (le
->ctrl
& EOP
) {
1582 if (unlikely(netif_msg_tx_done(sky2
)))
1583 printk(KERN_DEBUG
"%s: tx done %u\n",
1586 sky2
->net_stats
.tx_packets
++;
1587 sky2
->net_stats
.tx_bytes
+= re
->skb
->len
;
1589 dev_kfree_skb_any(re
->skb
);
1590 sky2
->tx_next
= RING_NEXT(idx
, TX_RING_SIZE
);
1594 sky2
->tx_cons
= idx
;
1597 if (tx_avail(sky2
) > MAX_SKB_TX_LE
+ 4)
1598 netif_wake_queue(dev
);
1601 /* Cleanup all untransmitted buffers, assume transmitter not running */
1602 static void sky2_tx_clean(struct net_device
*dev
)
1604 struct sky2_port
*sky2
= netdev_priv(dev
);
1606 netif_tx_lock_bh(dev
);
1607 sky2_tx_complete(sky2
, sky2
->tx_prod
);
1608 netif_tx_unlock_bh(dev
);
1611 /* Network shutdown */
1612 static int sky2_down(struct net_device
*dev
)
1614 struct sky2_port
*sky2
= netdev_priv(dev
);
1615 struct sky2_hw
*hw
= sky2
->hw
;
1616 unsigned port
= sky2
->port
;
1620 /* Never really got started! */
1624 if (netif_msg_ifdown(sky2
))
1625 printk(KERN_INFO PFX
"%s: disabling interface\n", dev
->name
);
1627 /* Stop more packets from being queued */
1628 netif_stop_queue(dev
);
1630 /* Disable port IRQ */
1631 imask
= sky2_read32(hw
, B0_IMSK
);
1632 imask
&= ~portirq_msk
[port
];
1633 sky2_write32(hw
, B0_IMSK
, imask
);
1635 sky2_gmac_reset(hw
, port
);
1637 /* Stop transmitter */
1638 sky2_write32(hw
, Q_ADDR(txqaddr
[port
], Q_CSR
), BMU_STOP
);
1639 sky2_read32(hw
, Q_ADDR(txqaddr
[port
], Q_CSR
));
1641 sky2_write32(hw
, RB_ADDR(txqaddr
[port
], RB_CTRL
),
1642 RB_RST_SET
| RB_DIS_OP_MD
);
1644 ctrl
= gma_read16(hw
, port
, GM_GP_CTRL
);
1645 ctrl
&= ~(GM_GPCR_TX_ENA
| GM_GPCR_RX_ENA
);
1646 gma_write16(hw
, port
, GM_GP_CTRL
, ctrl
);
1648 sky2_write8(hw
, SK_REG(port
, GPHY_CTRL
), GPC_RST_SET
);
1650 /* Workaround shared GMAC reset */
1651 if (!(hw
->chip_id
== CHIP_ID_YUKON_XL
&& hw
->chip_rev
== 0
1652 && port
== 0 && hw
->dev
[1] && netif_running(hw
->dev
[1])))
1653 sky2_write8(hw
, SK_REG(port
, GMAC_CTRL
), GMC_RST_SET
);
1655 /* Disable Force Sync bit and Enable Alloc bit */
1656 sky2_write8(hw
, SK_REG(port
, TXA_CTRL
),
1657 TXA_DIS_FSYNC
| TXA_DIS_ALLOC
| TXA_STOP_RC
);
1659 /* Stop Interval Timer and Limit Counter of Tx Arbiter */
1660 sky2_write32(hw
, SK_REG(port
, TXA_ITI_INI
), 0L);
1661 sky2_write32(hw
, SK_REG(port
, TXA_LIM_INI
), 0L);
1663 /* Reset the PCI FIFO of the async Tx queue */
1664 sky2_write32(hw
, Q_ADDR(txqaddr
[port
], Q_CSR
),
1665 BMU_RST_SET
| BMU_FIFO_RST
);
1667 /* Reset the Tx prefetch units */
1668 sky2_write32(hw
, Y2_QADDR(txqaddr
[port
], PREF_UNIT_CTRL
),
1671 sky2_write32(hw
, RB_ADDR(txqaddr
[port
], RB_CTRL
), RB_RST_SET
);
1675 sky2_write8(hw
, SK_REG(port
, RX_GMF_CTRL_T
), GMF_RST_SET
);
1676 sky2_write8(hw
, SK_REG(port
, TX_GMF_CTRL_T
), GMF_RST_SET
);
1678 sky2_phy_power(hw
, port
, 0);
1680 netif_carrier_off(dev
);
1682 /* turn off LED's */
1683 sky2_write16(hw
, B0_Y2LED
, LED_STAT_OFF
);
1685 synchronize_irq(hw
->pdev
->irq
);
1688 sky2_rx_clean(sky2
);
1690 pci_free_consistent(hw
->pdev
, RX_LE_BYTES
,
1691 sky2
->rx_le
, sky2
->rx_le_map
);
1692 kfree(sky2
->rx_ring
);
1694 pci_free_consistent(hw
->pdev
,
1695 TX_RING_SIZE
* sizeof(struct sky2_tx_le
),
1696 sky2
->tx_le
, sky2
->tx_le_map
);
1697 kfree(sky2
->tx_ring
);
1702 sky2
->rx_ring
= NULL
;
1703 sky2
->tx_ring
= NULL
;
1708 static u16
sky2_phy_speed(const struct sky2_hw
*hw
, u16 aux
)
1710 if (!sky2_is_copper(hw
))
1713 if (hw
->chip_id
== CHIP_ID_YUKON_FE
)
1714 return (aux
& PHY_M_PS_SPEED_100
) ? SPEED_100
: SPEED_10
;
1716 switch (aux
& PHY_M_PS_SPEED_MSK
) {
1717 case PHY_M_PS_SPEED_1000
:
1719 case PHY_M_PS_SPEED_100
:
1726 static void sky2_link_up(struct sky2_port
*sky2
)
1728 struct sky2_hw
*hw
= sky2
->hw
;
1729 unsigned port
= sky2
->port
;
1731 static const char *fc_name
[] = {
1739 reg
= gma_read16(hw
, port
, GM_GP_CTRL
);
1740 reg
|= GM_GPCR_RX_ENA
| GM_GPCR_TX_ENA
;
1741 gma_write16(hw
, port
, GM_GP_CTRL
, reg
);
1743 gm_phy_write(hw
, port
, PHY_MARV_INT_MASK
, PHY_M_DEF_MSK
);
1745 netif_carrier_on(sky2
->netdev
);
1747 /* Turn on link LED */
1748 sky2_write8(hw
, SK_REG(port
, LNK_LED_REG
),
1749 LINKLED_ON
| LINKLED_BLINK_OFF
| LINKLED_LINKSYNC_OFF
);
1751 if (hw
->chip_id
== CHIP_ID_YUKON_XL
1752 || hw
->chip_id
== CHIP_ID_YUKON_EC_U
1753 || hw
->chip_id
== CHIP_ID_YUKON_EX
) {
1754 u16 pg
= gm_phy_read(hw
, port
, PHY_MARV_EXT_ADR
);
1755 u16 led
= PHY_M_LEDC_LOS_CTRL(1); /* link active */
1757 switch(sky2
->speed
) {
1759 led
|= PHY_M_LEDC_INIT_CTRL(7);
1763 led
|= PHY_M_LEDC_STA1_CTRL(7);
1767 led
|= PHY_M_LEDC_STA0_CTRL(7);
1771 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, 3);
1772 gm_phy_write(hw
, port
, PHY_MARV_PHY_CTRL
, led
);
1773 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, pg
);
1776 if (netif_msg_link(sky2
))
1777 printk(KERN_INFO PFX
1778 "%s: Link is up at %d Mbps, %s duplex, flow control %s\n",
1779 sky2
->netdev
->name
, sky2
->speed
,
1780 sky2
->duplex
== DUPLEX_FULL
? "full" : "half",
1781 fc_name
[sky2
->flow_status
]);
1784 static void sky2_link_down(struct sky2_port
*sky2
)
1786 struct sky2_hw
*hw
= sky2
->hw
;
1787 unsigned port
= sky2
->port
;
1790 gm_phy_write(hw
, port
, PHY_MARV_INT_MASK
, 0);
1792 reg
= gma_read16(hw
, port
, GM_GP_CTRL
);
1793 reg
&= ~(GM_GPCR_RX_ENA
| GM_GPCR_TX_ENA
);
1794 gma_write16(hw
, port
, GM_GP_CTRL
, reg
);
1796 netif_carrier_off(sky2
->netdev
);
1798 /* Turn on link LED */
1799 sky2_write8(hw
, SK_REG(port
, LNK_LED_REG
), LINKLED_OFF
);
1801 if (netif_msg_link(sky2
))
1802 printk(KERN_INFO PFX
"%s: Link is down.\n", sky2
->netdev
->name
);
1804 sky2_phy_init(hw
, port
);
1807 static enum flow_control
sky2_flow(int rx
, int tx
)
1810 return tx
? FC_BOTH
: FC_RX
;
1812 return tx
? FC_TX
: FC_NONE
;
1815 static int sky2_autoneg_done(struct sky2_port
*sky2
, u16 aux
)
1817 struct sky2_hw
*hw
= sky2
->hw
;
1818 unsigned port
= sky2
->port
;
1821 advert
= gm_phy_read(hw
, port
, PHY_MARV_AUNE_ADV
);
1822 lpa
= gm_phy_read(hw
, port
, PHY_MARV_AUNE_LP
);
1823 if (lpa
& PHY_M_AN_RF
) {
1824 printk(KERN_ERR PFX
"%s: remote fault", sky2
->netdev
->name
);
1828 if (!(aux
& PHY_M_PS_SPDUP_RES
)) {
1829 printk(KERN_ERR PFX
"%s: speed/duplex mismatch",
1830 sky2
->netdev
->name
);
1834 sky2
->speed
= sky2_phy_speed(hw
, aux
);
1835 sky2
->duplex
= (aux
& PHY_M_PS_FULL_DUP
) ? DUPLEX_FULL
: DUPLEX_HALF
;
1837 /* Since the pause result bits seem to in different positions on
1838 * different chips. look at registers.
1840 if (!sky2_is_copper(hw
)) {
1841 /* Shift for bits in fiber PHY */
1842 advert
&= ~(ADVERTISE_PAUSE_CAP
|ADVERTISE_PAUSE_ASYM
);
1843 lpa
&= ~(LPA_PAUSE_CAP
|LPA_PAUSE_ASYM
);
1845 if (advert
& ADVERTISE_1000XPAUSE
)
1846 advert
|= ADVERTISE_PAUSE_CAP
;
1847 if (advert
& ADVERTISE_1000XPSE_ASYM
)
1848 advert
|= ADVERTISE_PAUSE_ASYM
;
1849 if (lpa
& LPA_1000XPAUSE
)
1850 lpa
|= LPA_PAUSE_CAP
;
1851 if (lpa
& LPA_1000XPAUSE_ASYM
)
1852 lpa
|= LPA_PAUSE_ASYM
;
1855 sky2
->flow_status
= FC_NONE
;
1856 if (advert
& ADVERTISE_PAUSE_CAP
) {
1857 if (lpa
& LPA_PAUSE_CAP
)
1858 sky2
->flow_status
= FC_BOTH
;
1859 else if (advert
& ADVERTISE_PAUSE_ASYM
)
1860 sky2
->flow_status
= FC_RX
;
1861 } else if (advert
& ADVERTISE_PAUSE_ASYM
) {
1862 if ((lpa
& LPA_PAUSE_CAP
) && (lpa
& LPA_PAUSE_ASYM
))
1863 sky2
->flow_status
= FC_TX
;
1866 if (sky2
->duplex
== DUPLEX_HALF
&& sky2
->speed
< SPEED_1000
1867 && !(hw
->chip_id
== CHIP_ID_YUKON_EC_U
|| hw
->chip_id
== CHIP_ID_YUKON_EX
))
1868 sky2
->flow_status
= FC_NONE
;
1870 if (sky2
->flow_status
& FC_TX
)
1871 sky2_write8(hw
, SK_REG(port
, GMAC_CTRL
), GMC_PAUSE_ON
);
1873 sky2_write8(hw
, SK_REG(port
, GMAC_CTRL
), GMC_PAUSE_OFF
);
1878 /* Interrupt from PHY */
1879 static void sky2_phy_intr(struct sky2_hw
*hw
, unsigned port
)
1881 struct net_device
*dev
= hw
->dev
[port
];
1882 struct sky2_port
*sky2
= netdev_priv(dev
);
1883 u16 istatus
, phystat
;
1885 if (!netif_running(dev
))
1888 spin_lock(&sky2
->phy_lock
);
1889 istatus
= gm_phy_read(hw
, port
, PHY_MARV_INT_STAT
);
1890 phystat
= gm_phy_read(hw
, port
, PHY_MARV_PHY_STAT
);
1892 if (netif_msg_intr(sky2
))
1893 printk(KERN_INFO PFX
"%s: phy interrupt status 0x%x 0x%x\n",
1894 sky2
->netdev
->name
, istatus
, phystat
);
1896 if (sky2
->autoneg
== AUTONEG_ENABLE
&& (istatus
& PHY_M_IS_AN_COMPL
)) {
1897 if (sky2_autoneg_done(sky2
, phystat
) == 0)
1902 if (istatus
& PHY_M_IS_LSP_CHANGE
)
1903 sky2
->speed
= sky2_phy_speed(hw
, phystat
);
1905 if (istatus
& PHY_M_IS_DUP_CHANGE
)
1907 (phystat
& PHY_M_PS_FULL_DUP
) ? DUPLEX_FULL
: DUPLEX_HALF
;
1909 if (istatus
& PHY_M_IS_LST_CHANGE
) {
1910 if (phystat
& PHY_M_PS_LINK_UP
)
1913 sky2_link_down(sky2
);
1916 spin_unlock(&sky2
->phy_lock
);
1919 /* Transmit timeout is only called if we are running, carrier is up
1920 * and tx queue is full (stopped).
1922 static void sky2_tx_timeout(struct net_device
*dev
)
1924 struct sky2_port
*sky2
= netdev_priv(dev
);
1925 struct sky2_hw
*hw
= sky2
->hw
;
1927 if (netif_msg_timer(sky2
))
1928 printk(KERN_ERR PFX
"%s: tx timeout\n", dev
->name
);
1930 printk(KERN_DEBUG PFX
"%s: transmit ring %u .. %u report=%u done=%u\n",
1931 dev
->name
, sky2
->tx_cons
, sky2
->tx_prod
,
1932 sky2_read16(hw
, sky2
->port
== 0 ? STAT_TXA1_RIDX
: STAT_TXA2_RIDX
),
1933 sky2_read16(hw
, Q_ADDR(txqaddr
[sky2
->port
], Q_DONE
)));
1935 /* can't restart safely under softirq */
1936 schedule_work(&hw
->restart_work
);
1939 static int sky2_change_mtu(struct net_device
*dev
, int new_mtu
)
1941 struct sky2_port
*sky2
= netdev_priv(dev
);
1942 struct sky2_hw
*hw
= sky2
->hw
;
1943 unsigned port
= sky2
->port
;
1948 if (new_mtu
< ETH_ZLEN
|| new_mtu
> ETH_JUMBO_MTU
)
1951 if (new_mtu
> ETH_DATA_LEN
&& hw
->chip_id
== CHIP_ID_YUKON_FE
)
1954 if (!netif_running(dev
)) {
1959 imask
= sky2_read32(hw
, B0_IMSK
);
1960 sky2_write32(hw
, B0_IMSK
, 0);
1962 dev
->trans_start
= jiffies
; /* prevent tx timeout */
1963 netif_stop_queue(dev
);
1964 netif_poll_disable(hw
->dev
[0]);
1966 synchronize_irq(hw
->pdev
->irq
);
1968 if (hw
->chip_id
== CHIP_ID_YUKON_EC_U
|| hw
->chip_id
== CHIP_ID_YUKON_EX
)
1969 sky2_set_tx_stfwd(hw
, port
);
1971 ctl
= gma_read16(hw
, port
, GM_GP_CTRL
);
1972 gma_write16(hw
, port
, GM_GP_CTRL
, ctl
& ~GM_GPCR_RX_ENA
);
1974 sky2_rx_clean(sky2
);
1978 mode
= DATA_BLIND_VAL(DATA_BLIND_DEF
) |
1979 GM_SMOD_VLAN_ENA
| IPG_DATA_VAL(IPG_DATA_DEF
);
1981 if (dev
->mtu
> ETH_DATA_LEN
)
1982 mode
|= GM_SMOD_JUMBO_ENA
;
1984 gma_write16(hw
, port
, GM_SERIAL_MODE
, mode
);
1986 sky2_write8(hw
, RB_ADDR(rxqaddr
[port
], RB_CTRL
), RB_ENA_OP_MD
);
1988 err
= sky2_rx_start(sky2
);
1989 sky2_write32(hw
, B0_IMSK
, imask
);
1994 gma_write16(hw
, port
, GM_GP_CTRL
, ctl
);
1996 netif_poll_enable(hw
->dev
[0]);
1997 netif_wake_queue(dev
);
2003 /* For small just reuse existing skb for next receive */
2004 static struct sk_buff
*receive_copy(struct sky2_port
*sky2
,
2005 const struct rx_ring_info
*re
,
2008 struct sk_buff
*skb
;
2010 skb
= netdev_alloc_skb(sky2
->netdev
, length
+ 2);
2012 skb_reserve(skb
, 2);
2013 pci_dma_sync_single_for_cpu(sky2
->hw
->pdev
, re
->data_addr
,
2014 length
, PCI_DMA_FROMDEVICE
);
2015 skb_copy_from_linear_data(re
->skb
, skb
->data
, length
);
2016 skb
->ip_summed
= re
->skb
->ip_summed
;
2017 skb
->csum
= re
->skb
->csum
;
2018 pci_dma_sync_single_for_device(sky2
->hw
->pdev
, re
->data_addr
,
2019 length
, PCI_DMA_FROMDEVICE
);
2020 re
->skb
->ip_summed
= CHECKSUM_NONE
;
2021 skb_put(skb
, length
);
2026 /* Adjust length of skb with fragments to match received data */
2027 static void skb_put_frags(struct sk_buff
*skb
, unsigned int hdr_space
,
2028 unsigned int length
)
2033 /* put header into skb */
2034 size
= min(length
, hdr_space
);
2039 num_frags
= skb_shinfo(skb
)->nr_frags
;
2040 for (i
= 0; i
< num_frags
; i
++) {
2041 skb_frag_t
*frag
= &skb_shinfo(skb
)->frags
[i
];
2044 /* don't need this page */
2045 __free_page(frag
->page
);
2046 --skb_shinfo(skb
)->nr_frags
;
2048 size
= min(length
, (unsigned) PAGE_SIZE
);
2051 skb
->data_len
+= size
;
2052 skb
->truesize
+= size
;
2059 /* Normal packet - take skb from ring element and put in a new one */
2060 static struct sk_buff
*receive_new(struct sky2_port
*sky2
,
2061 struct rx_ring_info
*re
,
2062 unsigned int length
)
2064 struct sk_buff
*skb
, *nskb
;
2065 unsigned hdr_space
= sky2
->rx_data_size
;
2067 pr_debug(PFX
"receive new length=%d\n", length
);
2069 /* Don't be tricky about reusing pages (yet) */
2070 nskb
= sky2_rx_alloc(sky2
);
2071 if (unlikely(!nskb
))
2075 sky2_rx_unmap_skb(sky2
->hw
->pdev
, re
);
2077 prefetch(skb
->data
);
2079 sky2_rx_map_skb(sky2
->hw
->pdev
, re
, hdr_space
);
2081 if (skb_shinfo(skb
)->nr_frags
)
2082 skb_put_frags(skb
, hdr_space
, length
);
2084 skb_put(skb
, length
);
2089 * Receive one packet.
2090 * For larger packets, get new buffer.
2092 static struct sk_buff
*sky2_receive(struct net_device
*dev
,
2093 u16 length
, u32 status
)
2095 struct sky2_port
*sky2
= netdev_priv(dev
);
2096 struct rx_ring_info
*re
= sky2
->rx_ring
+ sky2
->rx_next
;
2097 struct sk_buff
*skb
= NULL
;
2099 if (unlikely(netif_msg_rx_status(sky2
)))
2100 printk(KERN_DEBUG PFX
"%s: rx slot %u status 0x%x len %d\n",
2101 dev
->name
, sky2
->rx_next
, status
, length
);
2103 sky2
->rx_next
= (sky2
->rx_next
+ 1) % sky2
->rx_pending
;
2104 prefetch(sky2
->rx_ring
+ sky2
->rx_next
);
2106 if (status
& GMR_FS_ANY_ERR
)
2109 if (!(status
& GMR_FS_RX_OK
))
2112 if (status
>> 16 != length
)
2115 if (length
< copybreak
)
2116 skb
= receive_copy(sky2
, re
, length
);
2118 skb
= receive_new(sky2
, re
, length
);
2120 sky2_rx_submit(sky2
, re
);
2125 /* Truncation of overlength packets
2126 causes PHY length to not match MAC length */
2127 ++sky2
->net_stats
.rx_length_errors
;
2130 ++sky2
->net_stats
.rx_errors
;
2131 if (status
& GMR_FS_RX_FF_OV
) {
2132 sky2
->net_stats
.rx_over_errors
++;
2136 if (netif_msg_rx_err(sky2
) && net_ratelimit())
2137 printk(KERN_INFO PFX
"%s: rx error, status 0x%x length %d\n",
2138 dev
->name
, status
, length
);
2140 if (status
& (GMR_FS_LONG_ERR
| GMR_FS_UN_SIZE
))
2141 sky2
->net_stats
.rx_length_errors
++;
2142 if (status
& GMR_FS_FRAGMENT
)
2143 sky2
->net_stats
.rx_frame_errors
++;
2144 if (status
& GMR_FS_CRC_ERR
)
2145 sky2
->net_stats
.rx_crc_errors
++;
2150 /* Transmit complete */
2151 static inline void sky2_tx_done(struct net_device
*dev
, u16 last
)
2153 struct sky2_port
*sky2
= netdev_priv(dev
);
2155 if (netif_running(dev
)) {
2157 sky2_tx_complete(sky2
, last
);
2158 netif_tx_unlock(dev
);
2162 /* Process status response ring */
2163 static int sky2_status_intr(struct sky2_hw
*hw
, int to_do
)
2166 unsigned rx
[2] = { 0, 0 };
2167 u16 hwidx
= sky2_read16(hw
, STAT_PUT_IDX
);
2171 while (hw
->st_idx
!= hwidx
) {
2172 struct sky2_port
*sky2
;
2173 struct sky2_status_le
*le
= hw
->st_le
+ hw
->st_idx
;
2174 unsigned port
= le
->css
& CSS_LINK_BIT
;
2175 struct net_device
*dev
;
2176 struct sk_buff
*skb
;
2180 hw
->st_idx
= RING_NEXT(hw
->st_idx
, STATUS_RING_SIZE
);
2182 dev
= hw
->dev
[port
];
2183 sky2
= netdev_priv(dev
);
2184 length
= le16_to_cpu(le
->length
);
2185 status
= le32_to_cpu(le
->status
);
2187 switch (le
->opcode
& ~HW_OWNER
) {
2190 skb
= sky2_receive(dev
, length
, status
);
2191 if (unlikely(!skb
)) {
2192 sky2
->net_stats
.rx_dropped
++;
2196 /* This chip reports checksum status differently */
2197 if (hw
->chip_id
== CHIP_ID_YUKON_EX
) {
2198 if (sky2
->rx_csum
&&
2199 (le
->css
& (CSS_ISIPV4
| CSS_ISIPV6
)) &&
2200 (le
->css
& CSS_TCPUDPCSOK
))
2201 skb
->ip_summed
= CHECKSUM_UNNECESSARY
;
2203 skb
->ip_summed
= CHECKSUM_NONE
;
2206 skb
->protocol
= eth_type_trans(skb
, dev
);
2207 sky2
->net_stats
.rx_packets
++;
2208 sky2
->net_stats
.rx_bytes
+= skb
->len
;
2209 dev
->last_rx
= jiffies
;
2211 #ifdef SKY2_VLAN_TAG_USED
2212 if (sky2
->vlgrp
&& (status
& GMR_FS_VLAN
)) {
2213 vlan_hwaccel_receive_skb(skb
,
2215 be16_to_cpu(sky2
->rx_tag
));
2218 netif_receive_skb(skb
);
2220 /* Stop after net poll weight */
2221 if (++work_done
>= to_do
)
2225 #ifdef SKY2_VLAN_TAG_USED
2227 sky2
->rx_tag
= length
;
2231 sky2
->rx_tag
= length
;
2238 if (hw
->chip_id
== CHIP_ID_YUKON_EX
)
2241 /* Both checksum counters are programmed to start at
2242 * the same offset, so unless there is a problem they
2243 * should match. This failure is an early indication that
2244 * hardware receive checksumming won't work.
2246 if (likely(status
>> 16 == (status
& 0xffff))) {
2247 skb
= sky2
->rx_ring
[sky2
->rx_next
].skb
;
2248 skb
->ip_summed
= CHECKSUM_COMPLETE
;
2249 skb
->csum
= status
& 0xffff;
2251 printk(KERN_NOTICE PFX
"%s: hardware receive "
2252 "checksum problem (status = %#x)\n",
2255 sky2_write32(sky2
->hw
,
2256 Q_ADDR(rxqaddr
[port
], Q_CSR
),
2262 /* TX index reports status for both ports */
2263 BUILD_BUG_ON(TX_RING_SIZE
> 0x1000);
2264 sky2_tx_done(hw
->dev
[0], status
& 0xfff);
2266 sky2_tx_done(hw
->dev
[1],
2267 ((status
>> 24) & 0xff)
2268 | (u16
)(length
& 0xf) << 8);
2272 if (net_ratelimit())
2273 printk(KERN_WARNING PFX
2274 "unknown status opcode 0x%x\n", le
->opcode
);
2278 /* Fully processed status ring so clear irq */
2279 sky2_write32(hw
, STAT_CTRL
, SC_STAT_CLR_IRQ
);
2283 sky2_rx_update(netdev_priv(hw
->dev
[0]), Q_R1
);
2286 sky2_rx_update(netdev_priv(hw
->dev
[1]), Q_R2
);
2291 static void sky2_hw_error(struct sky2_hw
*hw
, unsigned port
, u32 status
)
2293 struct net_device
*dev
= hw
->dev
[port
];
2295 if (net_ratelimit())
2296 printk(KERN_INFO PFX
"%s: hw error interrupt status 0x%x\n",
2299 if (status
& Y2_IS_PAR_RD1
) {
2300 if (net_ratelimit())
2301 printk(KERN_ERR PFX
"%s: ram data read parity error\n",
2304 sky2_write16(hw
, RAM_BUFFER(port
, B3_RI_CTRL
), RI_CLR_RD_PERR
);
2307 if (status
& Y2_IS_PAR_WR1
) {
2308 if (net_ratelimit())
2309 printk(KERN_ERR PFX
"%s: ram data write parity error\n",
2312 sky2_write16(hw
, RAM_BUFFER(port
, B3_RI_CTRL
), RI_CLR_WR_PERR
);
2315 if (status
& Y2_IS_PAR_MAC1
) {
2316 if (net_ratelimit())
2317 printk(KERN_ERR PFX
"%s: MAC parity error\n", dev
->name
);
2318 sky2_write8(hw
, SK_REG(port
, TX_GMF_CTRL_T
), GMF_CLI_TX_PE
);
2321 if (status
& Y2_IS_PAR_RX1
) {
2322 if (net_ratelimit())
2323 printk(KERN_ERR PFX
"%s: RX parity error\n", dev
->name
);
2324 sky2_write32(hw
, Q_ADDR(rxqaddr
[port
], Q_CSR
), BMU_CLR_IRQ_PAR
);
2327 if (status
& Y2_IS_TCP_TXA1
) {
2328 if (net_ratelimit())
2329 printk(KERN_ERR PFX
"%s: TCP segmentation error\n",
2331 sky2_write32(hw
, Q_ADDR(txqaddr
[port
], Q_CSR
), BMU_CLR_IRQ_TCP
);
2335 static void sky2_hw_intr(struct sky2_hw
*hw
)
2337 u32 status
= sky2_read32(hw
, B0_HWE_ISRC
);
2339 if (status
& Y2_IS_TIST_OV
)
2340 sky2_write8(hw
, GMAC_TI_ST_CTRL
, GMT_ST_CLR_IRQ
);
2342 if (status
& (Y2_IS_MST_ERR
| Y2_IS_IRQ_STAT
)) {
2345 pci_err
= sky2_pci_read16(hw
, PCI_STATUS
);
2346 if (net_ratelimit())
2347 dev_err(&hw
->pdev
->dev
, "PCI hardware error (0x%x)\n",
2350 sky2_write8(hw
, B2_TST_CTRL1
, TST_CFG_WRITE_ON
);
2351 sky2_pci_write16(hw
, PCI_STATUS
,
2352 pci_err
| PCI_STATUS_ERROR_BITS
);
2353 sky2_write8(hw
, B2_TST_CTRL1
, TST_CFG_WRITE_OFF
);
2356 if (status
& Y2_IS_PCI_EXP
) {
2357 /* PCI-Express uncorrectable Error occurred */
2360 pex_err
= sky2_pci_read32(hw
, PEX_UNC_ERR_STAT
);
2362 if (net_ratelimit())
2363 dev_err(&hw
->pdev
->dev
, "PCI Express error (0x%x)\n",
2366 /* clear the interrupt */
2367 sky2_write32(hw
, B2_TST_CTRL1
, TST_CFG_WRITE_ON
);
2368 sky2_pci_write32(hw
, PEX_UNC_ERR_STAT
,
2370 sky2_write32(hw
, B2_TST_CTRL1
, TST_CFG_WRITE_OFF
);
2372 if (pex_err
& PEX_FATAL_ERRORS
) {
2373 u32 hwmsk
= sky2_read32(hw
, B0_HWE_IMSK
);
2374 hwmsk
&= ~Y2_IS_PCI_EXP
;
2375 sky2_write32(hw
, B0_HWE_IMSK
, hwmsk
);
2379 if (status
& Y2_HWE_L1_MASK
)
2380 sky2_hw_error(hw
, 0, status
);
2382 if (status
& Y2_HWE_L1_MASK
)
2383 sky2_hw_error(hw
, 1, status
);
2386 static void sky2_mac_intr(struct sky2_hw
*hw
, unsigned port
)
2388 struct net_device
*dev
= hw
->dev
[port
];
2389 struct sky2_port
*sky2
= netdev_priv(dev
);
2390 u8 status
= sky2_read8(hw
, SK_REG(port
, GMAC_IRQ_SRC
));
2392 if (netif_msg_intr(sky2
))
2393 printk(KERN_INFO PFX
"%s: mac interrupt status 0x%x\n",
2396 if (status
& GM_IS_RX_CO_OV
)
2397 gma_read16(hw
, port
, GM_RX_IRQ_SRC
);
2399 if (status
& GM_IS_TX_CO_OV
)
2400 gma_read16(hw
, port
, GM_TX_IRQ_SRC
);
2402 if (status
& GM_IS_RX_FF_OR
) {
2403 ++sky2
->net_stats
.rx_fifo_errors
;
2404 sky2_write8(hw
, SK_REG(port
, RX_GMF_CTRL_T
), GMF_CLI_RX_FO
);
2407 if (status
& GM_IS_TX_FF_UR
) {
2408 ++sky2
->net_stats
.tx_fifo_errors
;
2409 sky2_write8(hw
, SK_REG(port
, TX_GMF_CTRL_T
), GMF_CLI_TX_FU
);
2413 /* This should never happen it is a bug. */
2414 static void sky2_le_error(struct sky2_hw
*hw
, unsigned port
,
2415 u16 q
, unsigned ring_size
)
2417 struct net_device
*dev
= hw
->dev
[port
];
2418 struct sky2_port
*sky2
= netdev_priv(dev
);
2420 const u64
*le
= (q
== Q_R1
|| q
== Q_R2
)
2421 ? (u64
*) sky2
->rx_le
: (u64
*) sky2
->tx_le
;
2423 idx
= sky2_read16(hw
, Y2_QADDR(q
, PREF_UNIT_GET_IDX
));
2424 printk(KERN_ERR PFX
"%s: descriptor error q=%#x get=%u [%llx] put=%u\n",
2425 dev
->name
, (unsigned) q
, idx
, (unsigned long long) le
[idx
],
2426 (unsigned) sky2_read16(hw
, Y2_QADDR(q
, PREF_UNIT_PUT_IDX
)));
2428 sky2_write32(hw
, Q_ADDR(q
, Q_CSR
), BMU_CLR_IRQ_CHK
);
2431 /* If idle then force a fake soft NAPI poll once a second
2432 * to work around cases where sharing an edge triggered interrupt.
2434 static inline void sky2_idle_start(struct sky2_hw
*hw
)
2436 if (idle_timeout
> 0)
2437 mod_timer(&hw
->idle_timer
,
2438 jiffies
+ msecs_to_jiffies(idle_timeout
));
2441 static void sky2_idle(unsigned long arg
)
2443 struct sky2_hw
*hw
= (struct sky2_hw
*) arg
;
2444 struct net_device
*dev
= hw
->dev
[0];
2446 if (__netif_rx_schedule_prep(dev
))
2447 __netif_rx_schedule(dev
);
2449 mod_timer(&hw
->idle_timer
, jiffies
+ msecs_to_jiffies(idle_timeout
));
2452 /* Hardware/software error handling */
2453 static void sky2_err_intr(struct sky2_hw
*hw
, u32 status
)
2455 if (net_ratelimit())
2456 dev_warn(&hw
->pdev
->dev
, "error interrupt status=%#x\n", status
);
2458 if (status
& Y2_IS_HW_ERR
)
2461 if (status
& Y2_IS_IRQ_MAC1
)
2462 sky2_mac_intr(hw
, 0);
2464 if (status
& Y2_IS_IRQ_MAC2
)
2465 sky2_mac_intr(hw
, 1);
2467 if (status
& Y2_IS_CHK_RX1
)
2468 sky2_le_error(hw
, 0, Q_R1
, RX_LE_SIZE
);
2470 if (status
& Y2_IS_CHK_RX2
)
2471 sky2_le_error(hw
, 1, Q_R2
, RX_LE_SIZE
);
2473 if (status
& Y2_IS_CHK_TXA1
)
2474 sky2_le_error(hw
, 0, Q_XA1
, TX_RING_SIZE
);
2476 if (status
& Y2_IS_CHK_TXA2
)
2477 sky2_le_error(hw
, 1, Q_XA2
, TX_RING_SIZE
);
2480 static int sky2_poll(struct net_device
*dev0
, int *budget
)
2482 struct sky2_hw
*hw
= ((struct sky2_port
*) netdev_priv(dev0
))->hw
;
2484 u32 status
= sky2_read32(hw
, B0_Y2_SP_EISR
);
2486 if (unlikely(status
& Y2_IS_ERROR
))
2487 sky2_err_intr(hw
, status
);
2489 if (status
& Y2_IS_IRQ_PHY1
)
2490 sky2_phy_intr(hw
, 0);
2492 if (status
& Y2_IS_IRQ_PHY2
)
2493 sky2_phy_intr(hw
, 1);
2495 work_done
= sky2_status_intr(hw
, min(dev0
->quota
, *budget
));
2496 *budget
-= work_done
;
2497 dev0
->quota
-= work_done
;
2500 if (hw
->st_idx
!= sky2_read16(hw
, STAT_PUT_IDX
))
2503 /* Bug/Errata workaround?
2504 * Need to kick the TX irq moderation timer.
2506 if (sky2_read8(hw
, STAT_TX_TIMER_CTRL
) == TIM_START
) {
2507 sky2_write8(hw
, STAT_TX_TIMER_CTRL
, TIM_STOP
);
2508 sky2_write8(hw
, STAT_TX_TIMER_CTRL
, TIM_START
);
2510 netif_rx_complete(dev0
);
2512 sky2_read32(hw
, B0_Y2_SP_LISR
);
2516 static irqreturn_t
sky2_intr(int irq
, void *dev_id
)
2518 struct sky2_hw
*hw
= dev_id
;
2519 struct net_device
*dev0
= hw
->dev
[0];
2522 /* Reading this mask interrupts as side effect */
2523 status
= sky2_read32(hw
, B0_Y2_SP_ISRC2
);
2524 if (status
== 0 || status
== ~0)
2527 prefetch(&hw
->st_le
[hw
->st_idx
]);
2528 if (likely(__netif_rx_schedule_prep(dev0
)))
2529 __netif_rx_schedule(dev0
);
2534 #ifdef CONFIG_NET_POLL_CONTROLLER
2535 static void sky2_netpoll(struct net_device
*dev
)
2537 struct sky2_port
*sky2
= netdev_priv(dev
);
2538 struct net_device
*dev0
= sky2
->hw
->dev
[0];
2540 if (netif_running(dev
) && __netif_rx_schedule_prep(dev0
))
2541 __netif_rx_schedule(dev0
);
2545 /* Chip internal frequency for clock calculations */
2546 static inline u32
sky2_mhz(const struct sky2_hw
*hw
)
2548 switch (hw
->chip_id
) {
2549 case CHIP_ID_YUKON_EC
:
2550 case CHIP_ID_YUKON_EC_U
:
2551 case CHIP_ID_YUKON_EX
:
2552 return 125; /* 125 Mhz */
2553 case CHIP_ID_YUKON_FE
:
2554 return 100; /* 100 Mhz */
2555 default: /* YUKON_XL */
2556 return 156; /* 156 Mhz */
2560 static inline u32
sky2_us2clk(const struct sky2_hw
*hw
, u32 us
)
2562 return sky2_mhz(hw
) * us
;
2565 static inline u32
sky2_clk2us(const struct sky2_hw
*hw
, u32 clk
)
2567 return clk
/ sky2_mhz(hw
);
2571 static int __devinit
sky2_init(struct sky2_hw
*hw
)
2575 /* Enable all clocks */
2576 sky2_pci_write32(hw
, PCI_DEV_REG3
, 0);
2578 sky2_write8(hw
, B0_CTST
, CS_RST_CLR
);
2580 hw
->chip_id
= sky2_read8(hw
, B2_CHIP_ID
);
2581 if (hw
->chip_id
< CHIP_ID_YUKON_XL
|| hw
->chip_id
> CHIP_ID_YUKON_FE
) {
2582 dev_err(&hw
->pdev
->dev
, "unsupported chip type 0x%x\n",
2587 hw
->chip_rev
= (sky2_read8(hw
, B2_MAC_CFG
) & CFG_CHIP_R_MSK
) >> 4;
2589 /* This rev is really old, and requires untested workarounds */
2590 if (hw
->chip_id
== CHIP_ID_YUKON_EC
&& hw
->chip_rev
== CHIP_REV_YU_EC_A1
) {
2591 dev_err(&hw
->pdev
->dev
, "unsupported revision Yukon-%s (0x%x) rev %d\n",
2592 yukon2_name
[hw
->chip_id
- CHIP_ID_YUKON_XL
],
2593 hw
->chip_id
, hw
->chip_rev
);
2597 hw
->pmd_type
= sky2_read8(hw
, B2_PMD_TYP
);
2599 t8
= sky2_read8(hw
, B2_Y2_HW_RES
);
2600 if ((t8
& CFG_DUAL_MAC_MSK
) == CFG_DUAL_MAC_MSK
) {
2601 if (!(sky2_read8(hw
, B2_Y2_CLK_GATE
) & Y2_STATUS_LNK2_INAC
))
2608 static void sky2_reset(struct sky2_hw
*hw
)
2614 if (hw
->chip_id
== CHIP_ID_YUKON_EX
) {
2615 status
= sky2_read16(hw
, HCU_CCSR
);
2616 status
&= ~(HCU_CCSR_AHB_RST
| HCU_CCSR_CPU_RST_MODE
|
2617 HCU_CCSR_UC_STATE_MSK
);
2618 sky2_write16(hw
, HCU_CCSR
, status
);
2620 sky2_write8(hw
, B28_Y2_ASF_STAT_CMD
, Y2_ASF_RESET
);
2621 sky2_write16(hw
, B0_CTST
, Y2_ASF_DISABLE
);
2624 sky2_write8(hw
, B0_CTST
, CS_RST_SET
);
2625 sky2_write8(hw
, B0_CTST
, CS_RST_CLR
);
2627 /* clear PCI errors, if any */
2628 status
= sky2_pci_read16(hw
, PCI_STATUS
);
2630 sky2_write8(hw
, B2_TST_CTRL1
, TST_CFG_WRITE_ON
);
2631 sky2_pci_write16(hw
, PCI_STATUS
, status
| PCI_STATUS_ERROR_BITS
);
2634 sky2_write8(hw
, B0_CTST
, CS_MRST_CLR
);
2636 /* clear any PEX errors */
2637 if (pci_find_capability(hw
->pdev
, PCI_CAP_ID_EXP
))
2638 sky2_pci_write32(hw
, PEX_UNC_ERR_STAT
, 0xffffffffUL
);
2643 for (i
= 0; i
< hw
->ports
; i
++) {
2644 sky2_write8(hw
, SK_REG(i
, GMAC_LINK_CTRL
), GMLC_RST_SET
);
2645 sky2_write8(hw
, SK_REG(i
, GMAC_LINK_CTRL
), GMLC_RST_CLR
);
2647 if (hw
->chip_id
== CHIP_ID_YUKON_EX
)
2648 sky2_write16(hw
, SK_REG(i
, GMAC_CTRL
),
2649 GMC_BYP_MACSECRX_ON
| GMC_BYP_MACSECTX_ON
2653 sky2_write8(hw
, B2_TST_CTRL1
, TST_CFG_WRITE_OFF
);
2655 /* Clear I2C IRQ noise */
2656 sky2_write32(hw
, B2_I2C_IRQ
, 1);
2658 /* turn off hardware timer (unused) */
2659 sky2_write8(hw
, B2_TI_CTRL
, TIM_STOP
);
2660 sky2_write8(hw
, B2_TI_CTRL
, TIM_CLR_IRQ
);
2662 sky2_write8(hw
, B0_Y2LED
, LED_STAT_ON
);
2664 /* Turn off descriptor polling */
2665 sky2_write32(hw
, B28_DPT_CTRL
, DPT_STOP
);
2667 /* Turn off receive timestamp */
2668 sky2_write8(hw
, GMAC_TI_ST_CTRL
, GMT_ST_STOP
);
2669 sky2_write8(hw
, GMAC_TI_ST_CTRL
, GMT_ST_CLR_IRQ
);
2671 /* enable the Tx Arbiters */
2672 for (i
= 0; i
< hw
->ports
; i
++)
2673 sky2_write8(hw
, SK_REG(i
, TXA_CTRL
), TXA_ENA_ARB
);
2675 /* Initialize ram interface */
2676 for (i
= 0; i
< hw
->ports
; i
++) {
2677 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_CTRL
), RI_RST_CLR
);
2679 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_WTO_R1
), SK_RI_TO_53
);
2680 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_WTO_XA1
), SK_RI_TO_53
);
2681 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_WTO_XS1
), SK_RI_TO_53
);
2682 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_RTO_R1
), SK_RI_TO_53
);
2683 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_RTO_XA1
), SK_RI_TO_53
);
2684 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_RTO_XS1
), SK_RI_TO_53
);
2685 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_WTO_R2
), SK_RI_TO_53
);
2686 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_WTO_XA2
), SK_RI_TO_53
);
2687 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_WTO_XS2
), SK_RI_TO_53
);
2688 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_RTO_R2
), SK_RI_TO_53
);
2689 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_RTO_XA2
), SK_RI_TO_53
);
2690 sky2_write8(hw
, RAM_BUFFER(i
, B3_RI_RTO_XS2
), SK_RI_TO_53
);
2693 sky2_write32(hw
, B0_HWE_IMSK
, Y2_HWE_ALL_MASK
);
2695 for (i
= 0; i
< hw
->ports
; i
++)
2696 sky2_gmac_reset(hw
, i
);
2698 memset(hw
->st_le
, 0, STATUS_LE_BYTES
);
2701 sky2_write32(hw
, STAT_CTRL
, SC_STAT_RST_SET
);
2702 sky2_write32(hw
, STAT_CTRL
, SC_STAT_RST_CLR
);
2704 sky2_write32(hw
, STAT_LIST_ADDR_LO
, hw
->st_dma
);
2705 sky2_write32(hw
, STAT_LIST_ADDR_HI
, (u64
) hw
->st_dma
>> 32);
2707 /* Set the list last index */
2708 sky2_write16(hw
, STAT_LAST_IDX
, STATUS_RING_SIZE
- 1);
2710 sky2_write16(hw
, STAT_TX_IDX_TH
, 10);
2711 sky2_write8(hw
, STAT_FIFO_WM
, 16);
2713 /* set Status-FIFO ISR watermark */
2714 if (hw
->chip_id
== CHIP_ID_YUKON_XL
&& hw
->chip_rev
== 0)
2715 sky2_write8(hw
, STAT_FIFO_ISR_WM
, 4);
2717 sky2_write8(hw
, STAT_FIFO_ISR_WM
, 16);
2719 sky2_write32(hw
, STAT_TX_TIMER_INI
, sky2_us2clk(hw
, 1000));
2720 sky2_write32(hw
, STAT_ISR_TIMER_INI
, sky2_us2clk(hw
, 20));
2721 sky2_write32(hw
, STAT_LEV_TIMER_INI
, sky2_us2clk(hw
, 100));
2723 /* enable status unit */
2724 sky2_write32(hw
, STAT_CTRL
, SC_STAT_OP_ON
);
2726 sky2_write8(hw
, STAT_TX_TIMER_CTRL
, TIM_START
);
2727 sky2_write8(hw
, STAT_LEV_TIMER_CTRL
, TIM_START
);
2728 sky2_write8(hw
, STAT_ISR_TIMER_CTRL
, TIM_START
);
2731 static void sky2_restart(struct work_struct
*work
)
2733 struct sky2_hw
*hw
= container_of(work
, struct sky2_hw
, restart_work
);
2734 struct net_device
*dev
;
2737 dev_dbg(&hw
->pdev
->dev
, "restarting\n");
2739 del_timer_sync(&hw
->idle_timer
);
2742 sky2_write32(hw
, B0_IMSK
, 0);
2743 sky2_read32(hw
, B0_IMSK
);
2745 netif_poll_disable(hw
->dev
[0]);
2747 for (i
= 0; i
< hw
->ports
; i
++) {
2749 if (netif_running(dev
))
2754 sky2_write32(hw
, B0_IMSK
, Y2_IS_BASE
);
2755 netif_poll_enable(hw
->dev
[0]);
2757 for (i
= 0; i
< hw
->ports
; i
++) {
2759 if (netif_running(dev
)) {
2762 printk(KERN_INFO PFX
"%s: could not restart %d\n",
2769 sky2_idle_start(hw
);
2774 static inline u8
sky2_wol_supported(const struct sky2_hw
*hw
)
2776 return sky2_is_copper(hw
) ? (WAKE_PHY
| WAKE_MAGIC
) : 0;
2779 static void sky2_get_wol(struct net_device
*dev
, struct ethtool_wolinfo
*wol
)
2781 const struct sky2_port
*sky2
= netdev_priv(dev
);
2783 wol
->supported
= sky2_wol_supported(sky2
->hw
);
2784 wol
->wolopts
= sky2
->wol
;
2787 static int sky2_set_wol(struct net_device
*dev
, struct ethtool_wolinfo
*wol
)
2789 struct sky2_port
*sky2
= netdev_priv(dev
);
2790 struct sky2_hw
*hw
= sky2
->hw
;
2792 if (wol
->wolopts
& ~sky2_wol_supported(sky2
->hw
))
2795 sky2
->wol
= wol
->wolopts
;
2797 if (hw
->chip_id
== CHIP_ID_YUKON_EC_U
|| hw
->chip_id
== CHIP_ID_YUKON_EX
)
2798 sky2_write32(hw
, B0_CTST
, sky2
->wol
2799 ? Y2_HW_WOL_ON
: Y2_HW_WOL_OFF
);
2801 if (!netif_running(dev
))
2802 sky2_wol_init(sky2
);
2806 static u32
sky2_supported_modes(const struct sky2_hw
*hw
)
2808 if (sky2_is_copper(hw
)) {
2809 u32 modes
= SUPPORTED_10baseT_Half
2810 | SUPPORTED_10baseT_Full
2811 | SUPPORTED_100baseT_Half
2812 | SUPPORTED_100baseT_Full
2813 | SUPPORTED_Autoneg
| SUPPORTED_TP
;
2815 if (hw
->chip_id
!= CHIP_ID_YUKON_FE
)
2816 modes
|= SUPPORTED_1000baseT_Half
2817 | SUPPORTED_1000baseT_Full
;
2820 return SUPPORTED_1000baseT_Half
2821 | SUPPORTED_1000baseT_Full
2826 static int sky2_get_settings(struct net_device
*dev
, struct ethtool_cmd
*ecmd
)
2828 struct sky2_port
*sky2
= netdev_priv(dev
);
2829 struct sky2_hw
*hw
= sky2
->hw
;
2831 ecmd
->transceiver
= XCVR_INTERNAL
;
2832 ecmd
->supported
= sky2_supported_modes(hw
);
2833 ecmd
->phy_address
= PHY_ADDR_MARV
;
2834 if (sky2_is_copper(hw
)) {
2835 ecmd
->supported
= SUPPORTED_10baseT_Half
2836 | SUPPORTED_10baseT_Full
2837 | SUPPORTED_100baseT_Half
2838 | SUPPORTED_100baseT_Full
2839 | SUPPORTED_1000baseT_Half
2840 | SUPPORTED_1000baseT_Full
2841 | SUPPORTED_Autoneg
| SUPPORTED_TP
;
2842 ecmd
->port
= PORT_TP
;
2843 ecmd
->speed
= sky2
->speed
;
2845 ecmd
->speed
= SPEED_1000
;
2846 ecmd
->port
= PORT_FIBRE
;
2849 ecmd
->advertising
= sky2
->advertising
;
2850 ecmd
->autoneg
= sky2
->autoneg
;
2851 ecmd
->duplex
= sky2
->duplex
;
2855 static int sky2_set_settings(struct net_device
*dev
, struct ethtool_cmd
*ecmd
)
2857 struct sky2_port
*sky2
= netdev_priv(dev
);
2858 const struct sky2_hw
*hw
= sky2
->hw
;
2859 u32 supported
= sky2_supported_modes(hw
);
2861 if (ecmd
->autoneg
== AUTONEG_ENABLE
) {
2862 ecmd
->advertising
= supported
;
2868 switch (ecmd
->speed
) {
2870 if (ecmd
->duplex
== DUPLEX_FULL
)
2871 setting
= SUPPORTED_1000baseT_Full
;
2872 else if (ecmd
->duplex
== DUPLEX_HALF
)
2873 setting
= SUPPORTED_1000baseT_Half
;
2878 if (ecmd
->duplex
== DUPLEX_FULL
)
2879 setting
= SUPPORTED_100baseT_Full
;
2880 else if (ecmd
->duplex
== DUPLEX_HALF
)
2881 setting
= SUPPORTED_100baseT_Half
;
2887 if (ecmd
->duplex
== DUPLEX_FULL
)
2888 setting
= SUPPORTED_10baseT_Full
;
2889 else if (ecmd
->duplex
== DUPLEX_HALF
)
2890 setting
= SUPPORTED_10baseT_Half
;
2898 if ((setting
& supported
) == 0)
2901 sky2
->speed
= ecmd
->speed
;
2902 sky2
->duplex
= ecmd
->duplex
;
2905 sky2
->autoneg
= ecmd
->autoneg
;
2906 sky2
->advertising
= ecmd
->advertising
;
2908 if (netif_running(dev
))
2909 sky2_phy_reinit(sky2
);
2914 static void sky2_get_drvinfo(struct net_device
*dev
,
2915 struct ethtool_drvinfo
*info
)
2917 struct sky2_port
*sky2
= netdev_priv(dev
);
2919 strcpy(info
->driver
, DRV_NAME
);
2920 strcpy(info
->version
, DRV_VERSION
);
2921 strcpy(info
->fw_version
, "N/A");
2922 strcpy(info
->bus_info
, pci_name(sky2
->hw
->pdev
));
2925 static const struct sky2_stat
{
2926 char name
[ETH_GSTRING_LEN
];
2929 { "tx_bytes", GM_TXO_OK_HI
},
2930 { "rx_bytes", GM_RXO_OK_HI
},
2931 { "tx_broadcast", GM_TXF_BC_OK
},
2932 { "rx_broadcast", GM_RXF_BC_OK
},
2933 { "tx_multicast", GM_TXF_MC_OK
},
2934 { "rx_multicast", GM_RXF_MC_OK
},
2935 { "tx_unicast", GM_TXF_UC_OK
},
2936 { "rx_unicast", GM_RXF_UC_OK
},
2937 { "tx_mac_pause", GM_TXF_MPAUSE
},
2938 { "rx_mac_pause", GM_RXF_MPAUSE
},
2939 { "collisions", GM_TXF_COL
},
2940 { "late_collision",GM_TXF_LAT_COL
},
2941 { "aborted", GM_TXF_ABO_COL
},
2942 { "single_collisions", GM_TXF_SNG_COL
},
2943 { "multi_collisions", GM_TXF_MUL_COL
},
2945 { "rx_short", GM_RXF_SHT
},
2946 { "rx_runt", GM_RXE_FRAG
},
2947 { "rx_64_byte_packets", GM_RXF_64B
},
2948 { "rx_65_to_127_byte_packets", GM_RXF_127B
},
2949 { "rx_128_to_255_byte_packets", GM_RXF_255B
},
2950 { "rx_256_to_511_byte_packets", GM_RXF_511B
},
2951 { "rx_512_to_1023_byte_packets", GM_RXF_1023B
},
2952 { "rx_1024_to_1518_byte_packets", GM_RXF_1518B
},
2953 { "rx_1518_to_max_byte_packets", GM_RXF_MAX_SZ
},
2954 { "rx_too_long", GM_RXF_LNG_ERR
},
2955 { "rx_fifo_overflow", GM_RXE_FIFO_OV
},
2956 { "rx_jabber", GM_RXF_JAB_PKT
},
2957 { "rx_fcs_error", GM_RXF_FCS_ERR
},
2959 { "tx_64_byte_packets", GM_TXF_64B
},
2960 { "tx_65_to_127_byte_packets", GM_TXF_127B
},
2961 { "tx_128_to_255_byte_packets", GM_TXF_255B
},
2962 { "tx_256_to_511_byte_packets", GM_TXF_511B
},
2963 { "tx_512_to_1023_byte_packets", GM_TXF_1023B
},
2964 { "tx_1024_to_1518_byte_packets", GM_TXF_1518B
},
2965 { "tx_1519_to_max_byte_packets", GM_TXF_MAX_SZ
},
2966 { "tx_fifo_underrun", GM_TXE_FIFO_UR
},
2969 static u32
sky2_get_rx_csum(struct net_device
*dev
)
2971 struct sky2_port
*sky2
= netdev_priv(dev
);
2973 return sky2
->rx_csum
;
2976 static int sky2_set_rx_csum(struct net_device
*dev
, u32 data
)
2978 struct sky2_port
*sky2
= netdev_priv(dev
);
2980 sky2
->rx_csum
= data
;
2982 sky2_write32(sky2
->hw
, Q_ADDR(rxqaddr
[sky2
->port
], Q_CSR
),
2983 data
? BMU_ENA_RX_CHKSUM
: BMU_DIS_RX_CHKSUM
);
2988 static u32
sky2_get_msglevel(struct net_device
*netdev
)
2990 struct sky2_port
*sky2
= netdev_priv(netdev
);
2991 return sky2
->msg_enable
;
2994 static int sky2_nway_reset(struct net_device
*dev
)
2996 struct sky2_port
*sky2
= netdev_priv(dev
);
2998 if (!netif_running(dev
) || sky2
->autoneg
!= AUTONEG_ENABLE
)
3001 sky2_phy_reinit(sky2
);
3006 static void sky2_phy_stats(struct sky2_port
*sky2
, u64
* data
, unsigned count
)
3008 struct sky2_hw
*hw
= sky2
->hw
;
3009 unsigned port
= sky2
->port
;
3012 data
[0] = (u64
) gma_read32(hw
, port
, GM_TXO_OK_HI
) << 32
3013 | (u64
) gma_read32(hw
, port
, GM_TXO_OK_LO
);
3014 data
[1] = (u64
) gma_read32(hw
, port
, GM_RXO_OK_HI
) << 32
3015 | (u64
) gma_read32(hw
, port
, GM_RXO_OK_LO
);
3017 for (i
= 2; i
< count
; i
++)
3018 data
[i
] = (u64
) gma_read32(hw
, port
, sky2_stats
[i
].offset
);
3021 static void sky2_set_msglevel(struct net_device
*netdev
, u32 value
)
3023 struct sky2_port
*sky2
= netdev_priv(netdev
);
3024 sky2
->msg_enable
= value
;
3027 static int sky2_get_stats_count(struct net_device
*dev
)
3029 return ARRAY_SIZE(sky2_stats
);
3032 static void sky2_get_ethtool_stats(struct net_device
*dev
,
3033 struct ethtool_stats
*stats
, u64
* data
)
3035 struct sky2_port
*sky2
= netdev_priv(dev
);
3037 sky2_phy_stats(sky2
, data
, ARRAY_SIZE(sky2_stats
));
3040 static void sky2_get_strings(struct net_device
*dev
, u32 stringset
, u8
* data
)
3044 switch (stringset
) {
3046 for (i
= 0; i
< ARRAY_SIZE(sky2_stats
); i
++)
3047 memcpy(data
+ i
* ETH_GSTRING_LEN
,
3048 sky2_stats
[i
].name
, ETH_GSTRING_LEN
);
3053 static struct net_device_stats
*sky2_get_stats(struct net_device
*dev
)
3055 struct sky2_port
*sky2
= netdev_priv(dev
);
3056 return &sky2
->net_stats
;
3059 static int sky2_set_mac_address(struct net_device
*dev
, void *p
)
3061 struct sky2_port
*sky2
= netdev_priv(dev
);
3062 struct sky2_hw
*hw
= sky2
->hw
;
3063 unsigned port
= sky2
->port
;
3064 const struct sockaddr
*addr
= p
;
3066 if (!is_valid_ether_addr(addr
->sa_data
))
3067 return -EADDRNOTAVAIL
;
3069 memcpy(dev
->dev_addr
, addr
->sa_data
, ETH_ALEN
);
3070 memcpy_toio(hw
->regs
+ B2_MAC_1
+ port
* 8,
3071 dev
->dev_addr
, ETH_ALEN
);
3072 memcpy_toio(hw
->regs
+ B2_MAC_2
+ port
* 8,
3073 dev
->dev_addr
, ETH_ALEN
);
3075 /* virtual address for data */
3076 gma_set_addr(hw
, port
, GM_SRC_ADDR_2L
, dev
->dev_addr
);
3078 /* physical address: used for pause frames */
3079 gma_set_addr(hw
, port
, GM_SRC_ADDR_1L
, dev
->dev_addr
);
3084 static void inline sky2_add_filter(u8 filter
[8], const u8
*addr
)
3088 bit
= ether_crc(ETH_ALEN
, addr
) & 63;
3089 filter
[bit
>> 3] |= 1 << (bit
& 7);
3092 static void sky2_set_multicast(struct net_device
*dev
)
3094 struct sky2_port
*sky2
= netdev_priv(dev
);
3095 struct sky2_hw
*hw
= sky2
->hw
;
3096 unsigned port
= sky2
->port
;
3097 struct dev_mc_list
*list
= dev
->mc_list
;
3101 static const u8 pause_mc_addr
[ETH_ALEN
] = { 0x1, 0x80, 0xc2, 0x0, 0x0, 0x1 };
3103 rx_pause
= (sky2
->flow_status
== FC_RX
|| sky2
->flow_status
== FC_BOTH
);
3104 memset(filter
, 0, sizeof(filter
));
3106 reg
= gma_read16(hw
, port
, GM_RX_CTRL
);
3107 reg
|= GM_RXCR_UCF_ENA
;
3109 if (dev
->flags
& IFF_PROMISC
) /* promiscuous */
3110 reg
&= ~(GM_RXCR_UCF_ENA
| GM_RXCR_MCF_ENA
);
3111 else if (dev
->flags
& IFF_ALLMULTI
)
3112 memset(filter
, 0xff, sizeof(filter
));
3113 else if (dev
->mc_count
== 0 && !rx_pause
)
3114 reg
&= ~GM_RXCR_MCF_ENA
;
3117 reg
|= GM_RXCR_MCF_ENA
;
3120 sky2_add_filter(filter
, pause_mc_addr
);
3122 for (i
= 0; list
&& i
< dev
->mc_count
; i
++, list
= list
->next
)
3123 sky2_add_filter(filter
, list
->dmi_addr
);
3126 gma_write16(hw
, port
, GM_MC_ADDR_H1
,
3127 (u16
) filter
[0] | ((u16
) filter
[1] << 8));
3128 gma_write16(hw
, port
, GM_MC_ADDR_H2
,
3129 (u16
) filter
[2] | ((u16
) filter
[3] << 8));
3130 gma_write16(hw
, port
, GM_MC_ADDR_H3
,
3131 (u16
) filter
[4] | ((u16
) filter
[5] << 8));
3132 gma_write16(hw
, port
, GM_MC_ADDR_H4
,
3133 (u16
) filter
[6] | ((u16
) filter
[7] << 8));
3135 gma_write16(hw
, port
, GM_RX_CTRL
, reg
);
3138 /* Can have one global because blinking is controlled by
3139 * ethtool and that is always under RTNL mutex
3141 static void sky2_led(struct sky2_hw
*hw
, unsigned port
, int on
)
3145 switch (hw
->chip_id
) {
3146 case CHIP_ID_YUKON_XL
:
3147 pg
= gm_phy_read(hw
, port
, PHY_MARV_EXT_ADR
);
3148 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, 3);
3149 gm_phy_write(hw
, port
, PHY_MARV_PHY_CTRL
,
3150 on
? (PHY_M_LEDC_LOS_CTRL(1) |
3151 PHY_M_LEDC_INIT_CTRL(7) |
3152 PHY_M_LEDC_STA1_CTRL(7) |
3153 PHY_M_LEDC_STA0_CTRL(7))
3156 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, pg
);
3160 gm_phy_write(hw
, port
, PHY_MARV_LED_CTRL
, 0);
3161 gm_phy_write(hw
, port
, PHY_MARV_LED_OVER
,
3162 on
? PHY_M_LED_ALL
: 0);
3166 /* blink LED's for finding board */
3167 static int sky2_phys_id(struct net_device
*dev
, u32 data
)
3169 struct sky2_port
*sky2
= netdev_priv(dev
);
3170 struct sky2_hw
*hw
= sky2
->hw
;
3171 unsigned port
= sky2
->port
;
3172 u16 ledctrl
, ledover
= 0;
3177 if (!data
|| data
> (u32
) (MAX_SCHEDULE_TIMEOUT
/ HZ
))
3178 ms
= jiffies_to_msecs(MAX_SCHEDULE_TIMEOUT
);
3182 /* save initial values */
3183 spin_lock_bh(&sky2
->phy_lock
);
3184 if (hw
->chip_id
== CHIP_ID_YUKON_XL
) {
3185 u16 pg
= gm_phy_read(hw
, port
, PHY_MARV_EXT_ADR
);
3186 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, 3);
3187 ledctrl
= gm_phy_read(hw
, port
, PHY_MARV_PHY_CTRL
);
3188 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, pg
);
3190 ledctrl
= gm_phy_read(hw
, port
, PHY_MARV_LED_CTRL
);
3191 ledover
= gm_phy_read(hw
, port
, PHY_MARV_LED_OVER
);
3195 while (!interrupted
&& ms
> 0) {
3196 sky2_led(hw
, port
, onoff
);
3199 spin_unlock_bh(&sky2
->phy_lock
);
3200 interrupted
= msleep_interruptible(250);
3201 spin_lock_bh(&sky2
->phy_lock
);
3206 /* resume regularly scheduled programming */
3207 if (hw
->chip_id
== CHIP_ID_YUKON_XL
) {
3208 u16 pg
= gm_phy_read(hw
, port
, PHY_MARV_EXT_ADR
);
3209 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, 3);
3210 gm_phy_write(hw
, port
, PHY_MARV_PHY_CTRL
, ledctrl
);
3211 gm_phy_write(hw
, port
, PHY_MARV_EXT_ADR
, pg
);
3213 gm_phy_write(hw
, port
, PHY_MARV_LED_CTRL
, ledctrl
);
3214 gm_phy_write(hw
, port
, PHY_MARV_LED_OVER
, ledover
);
3216 spin_unlock_bh(&sky2
->phy_lock
);
3221 static void sky2_get_pauseparam(struct net_device
*dev
,
3222 struct ethtool_pauseparam
*ecmd
)
3224 struct sky2_port
*sky2
= netdev_priv(dev
);
3226 switch (sky2
->flow_mode
) {
3228 ecmd
->tx_pause
= ecmd
->rx_pause
= 0;
3231 ecmd
->tx_pause
= 1, ecmd
->rx_pause
= 0;
3234 ecmd
->tx_pause
= 0, ecmd
->rx_pause
= 1;
3237 ecmd
->tx_pause
= ecmd
->rx_pause
= 1;
3240 ecmd
->autoneg
= sky2
->autoneg
;
3243 static int sky2_set_pauseparam(struct net_device
*dev
,
3244 struct ethtool_pauseparam
*ecmd
)
3246 struct sky2_port
*sky2
= netdev_priv(dev
);
3248 sky2
->autoneg
= ecmd
->autoneg
;
3249 sky2
->flow_mode
= sky2_flow(ecmd
->rx_pause
, ecmd
->tx_pause
);
3251 if (netif_running(dev
))
3252 sky2_phy_reinit(sky2
);
3257 static int sky2_get_coalesce(struct net_device
*dev
,
3258 struct ethtool_coalesce
*ecmd
)
3260 struct sky2_port
*sky2
= netdev_priv(dev
);
3261 struct sky2_hw
*hw
= sky2
->hw
;
3263 if (sky2_read8(hw
, STAT_TX_TIMER_CTRL
) == TIM_STOP
)
3264 ecmd
->tx_coalesce_usecs
= 0;
3266 u32 clks
= sky2_read32(hw
, STAT_TX_TIMER_INI
);
3267 ecmd
->tx_coalesce_usecs
= sky2_clk2us(hw
, clks
);
3269 ecmd
->tx_max_coalesced_frames
= sky2_read16(hw
, STAT_TX_IDX_TH
);
3271 if (sky2_read8(hw
, STAT_LEV_TIMER_CTRL
) == TIM_STOP
)
3272 ecmd
->rx_coalesce_usecs
= 0;
3274 u32 clks
= sky2_read32(hw
, STAT_LEV_TIMER_INI
);
3275 ecmd
->rx_coalesce_usecs
= sky2_clk2us(hw
, clks
);
3277 ecmd
->rx_max_coalesced_frames
= sky2_read8(hw
, STAT_FIFO_WM
);
3279 if (sky2_read8(hw
, STAT_ISR_TIMER_CTRL
) == TIM_STOP
)
3280 ecmd
->rx_coalesce_usecs_irq
= 0;
3282 u32 clks
= sky2_read32(hw
, STAT_ISR_TIMER_INI
);
3283 ecmd
->rx_coalesce_usecs_irq
= sky2_clk2us(hw
, clks
);
3286 ecmd
->rx_max_coalesced_frames_irq
= sky2_read8(hw
, STAT_FIFO_ISR_WM
);
3291 /* Note: this affect both ports */
3292 static int sky2_set_coalesce(struct net_device
*dev
,
3293 struct ethtool_coalesce
*ecmd
)
3295 struct sky2_port
*sky2
= netdev_priv(dev
);
3296 struct sky2_hw
*hw
= sky2
->hw
;
3297 const u32 tmax
= sky2_clk2us(hw
, 0x0ffffff);
3299 if (ecmd
->tx_coalesce_usecs
> tmax
||
3300 ecmd
->rx_coalesce_usecs
> tmax
||
3301 ecmd
->rx_coalesce_usecs_irq
> tmax
)
3304 if (ecmd
->tx_max_coalesced_frames
>= TX_RING_SIZE
-1)
3306 if (ecmd
->rx_max_coalesced_frames
> RX_MAX_PENDING
)
3308 if (ecmd
->rx_max_coalesced_frames_irq
>RX_MAX_PENDING
)
3311 if (ecmd
->tx_coalesce_usecs
== 0)
3312 sky2_write8(hw
, STAT_TX_TIMER_CTRL
, TIM_STOP
);
3314 sky2_write32(hw
, STAT_TX_TIMER_INI
,
3315 sky2_us2clk(hw
, ecmd
->tx_coalesce_usecs
));
3316 sky2_write8(hw
, STAT_TX_TIMER_CTRL
, TIM_START
);
3318 sky2_write16(hw
, STAT_TX_IDX_TH
, ecmd
->tx_max_coalesced_frames
);
3320 if (ecmd
->rx_coalesce_usecs
== 0)
3321 sky2_write8(hw
, STAT_LEV_TIMER_CTRL
, TIM_STOP
);
3323 sky2_write32(hw
, STAT_LEV_TIMER_INI
,
3324 sky2_us2clk(hw
, ecmd
->rx_coalesce_usecs
));
3325 sky2_write8(hw
, STAT_LEV_TIMER_CTRL
, TIM_START
);
3327 sky2_write8(hw
, STAT_FIFO_WM
, ecmd
->rx_max_coalesced_frames
);
3329 if (ecmd
->rx_coalesce_usecs_irq
== 0)
3330 sky2_write8(hw
, STAT_ISR_TIMER_CTRL
, TIM_STOP
);
3332 sky2_write32(hw
, STAT_ISR_TIMER_INI
,
3333 sky2_us2clk(hw
, ecmd
->rx_coalesce_usecs_irq
));
3334 sky2_write8(hw
, STAT_ISR_TIMER_CTRL
, TIM_START
);
3336 sky2_write8(hw
, STAT_FIFO_ISR_WM
, ecmd
->rx_max_coalesced_frames_irq
);
3340 static void sky2_get_ringparam(struct net_device
*dev
,
3341 struct ethtool_ringparam
*ering
)
3343 struct sky2_port
*sky2
= netdev_priv(dev
);
3345 ering
->rx_max_pending
= RX_MAX_PENDING
;
3346 ering
->rx_mini_max_pending
= 0;
3347 ering
->rx_jumbo_max_pending
= 0;
3348 ering
->tx_max_pending
= TX_RING_SIZE
- 1;
3350 ering
->rx_pending
= sky2
->rx_pending
;
3351 ering
->rx_mini_pending
= 0;
3352 ering
->rx_jumbo_pending
= 0;
3353 ering
->tx_pending
= sky2
->tx_pending
;
3356 static int sky2_set_ringparam(struct net_device
*dev
,
3357 struct ethtool_ringparam
*ering
)
3359 struct sky2_port
*sky2
= netdev_priv(dev
);
3362 if (ering
->rx_pending
> RX_MAX_PENDING
||
3363 ering
->rx_pending
< 8 ||
3364 ering
->tx_pending
< MAX_SKB_TX_LE
||
3365 ering
->tx_pending
> TX_RING_SIZE
- 1)
3368 if (netif_running(dev
))
3371 sky2
->rx_pending
= ering
->rx_pending
;
3372 sky2
->tx_pending
= ering
->tx_pending
;
3374 if (netif_running(dev
)) {
3379 sky2_set_multicast(dev
);
3385 static int sky2_get_regs_len(struct net_device
*dev
)
3391 * Returns copy of control register region
3392 * Note: ethtool_get_regs always provides full size (16k) buffer
3394 static void sky2_get_regs(struct net_device
*dev
, struct ethtool_regs
*regs
,
3397 const struct sky2_port
*sky2
= netdev_priv(dev
);
3398 const void __iomem
*io
= sky2
->hw
->regs
;
3401 memset(p
, 0, regs
->len
);
3403 memcpy_fromio(p
, io
, B3_RAM_ADDR
);
3405 /* skip diagnostic ram region */
3406 memcpy_fromio(p
+ B3_RI_WTO_R1
, io
+ B3_RI_WTO_R1
, 0x2000 - B3_RI_WTO_R1
);
3408 /* copy GMAC registers */
3409 memcpy_fromio(p
+ BASE_GMAC_1
, io
+ BASE_GMAC_1
, 0x1000);
3410 if (sky2
->hw
->ports
> 1)
3411 memcpy_fromio(p
+ BASE_GMAC_2
, io
+ BASE_GMAC_2
, 0x1000);
3415 /* In order to do Jumbo packets on these chips, need to turn off the
3416 * transmit store/forward. Therefore checksum offload won't work.
3418 static int no_tx_offload(struct net_device
*dev
)
3420 const struct sky2_port
*sky2
= netdev_priv(dev
);
3421 const struct sky2_hw
*hw
= sky2
->hw
;
3423 return dev
->mtu
> ETH_DATA_LEN
&& hw
->chip_id
== CHIP_ID_YUKON_EC_U
;
3426 static int sky2_set_tx_csum(struct net_device
*dev
, u32 data
)
3428 if (data
&& no_tx_offload(dev
))
3431 return ethtool_op_set_tx_csum(dev
, data
);
3435 static int sky2_set_tso(struct net_device
*dev
, u32 data
)
3437 if (data
&& no_tx_offload(dev
))
3440 return ethtool_op_set_tso(dev
, data
);
3443 static int sky2_get_eeprom_len(struct net_device
*dev
)
3445 struct sky2_port
*sky2
= netdev_priv(dev
);
3448 reg2
= sky2_pci_read32(sky2
->hw
, PCI_DEV_REG2
);
3449 return 1 << ( ((reg2
& PCI_VPD_ROM_SZ
) >> 14) + 8);
3452 static u32
sky2_vpd_read(struct sky2_hw
*hw
, int cap
, u16 offset
)
3454 sky2_pci_write16(hw
, cap
+ PCI_VPD_ADDR
, offset
);
3456 while (!(sky2_pci_read16(hw
, cap
+ PCI_VPD_ADDR
) & PCI_VPD_ADDR_F
))
3458 return sky2_pci_read32(hw
, cap
+ PCI_VPD_DATA
);
3461 static void sky2_vpd_write(struct sky2_hw
*hw
, int cap
, u16 offset
, u32 val
)
3463 sky2_pci_write32(hw
, cap
+ PCI_VPD_DATA
, val
);
3464 sky2_pci_write16(hw
, cap
+ PCI_VPD_ADDR
, offset
| PCI_VPD_ADDR_F
);
3467 } while (sky2_pci_read16(hw
, cap
+ PCI_VPD_ADDR
) & PCI_VPD_ADDR_F
);
3470 static int sky2_get_eeprom(struct net_device
*dev
, struct ethtool_eeprom
*eeprom
,
3473 struct sky2_port
*sky2
= netdev_priv(dev
);
3474 int cap
= pci_find_capability(sky2
->hw
->pdev
, PCI_CAP_ID_VPD
);
3475 int length
= eeprom
->len
;
3476 u16 offset
= eeprom
->offset
;
3481 eeprom
->magic
= SKY2_EEPROM_MAGIC
;
3483 while (length
> 0) {
3484 u32 val
= sky2_vpd_read(sky2
->hw
, cap
, offset
);
3485 int n
= min_t(int, length
, sizeof(val
));
3487 memcpy(data
, &val
, n
);
3495 static int sky2_set_eeprom(struct net_device
*dev
, struct ethtool_eeprom
*eeprom
,
3498 struct sky2_port
*sky2
= netdev_priv(dev
);
3499 int cap
= pci_find_capability(sky2
->hw
->pdev
, PCI_CAP_ID_VPD
);
3500 int length
= eeprom
->len
;
3501 u16 offset
= eeprom
->offset
;
3506 if (eeprom
->magic
!= SKY2_EEPROM_MAGIC
)
3509 while (length
> 0) {
3511 int n
= min_t(int, length
, sizeof(val
));
3513 if (n
< sizeof(val
))
3514 val
= sky2_vpd_read(sky2
->hw
, cap
, offset
);
3515 memcpy(&val
, data
, n
);
3517 sky2_vpd_write(sky2
->hw
, cap
, offset
, val
);
3527 static const struct ethtool_ops sky2_ethtool_ops
= {
3528 .get_settings
= sky2_get_settings
,
3529 .set_settings
= sky2_set_settings
,
3530 .get_drvinfo
= sky2_get_drvinfo
,
3531 .get_wol
= sky2_get_wol
,
3532 .set_wol
= sky2_set_wol
,
3533 .get_msglevel
= sky2_get_msglevel
,
3534 .set_msglevel
= sky2_set_msglevel
,
3535 .nway_reset
= sky2_nway_reset
,
3536 .get_regs_len
= sky2_get_regs_len
,
3537 .get_regs
= sky2_get_regs
,
3538 .get_link
= ethtool_op_get_link
,
3539 .get_eeprom_len
= sky2_get_eeprom_len
,
3540 .get_eeprom
= sky2_get_eeprom
,
3541 .set_eeprom
= sky2_set_eeprom
,
3542 .get_sg
= ethtool_op_get_sg
,
3543 .set_sg
= ethtool_op_set_sg
,
3544 .get_tx_csum
= ethtool_op_get_tx_csum
,
3545 .set_tx_csum
= sky2_set_tx_csum
,
3546 .get_tso
= ethtool_op_get_tso
,
3547 .set_tso
= sky2_set_tso
,
3548 .get_rx_csum
= sky2_get_rx_csum
,
3549 .set_rx_csum
= sky2_set_rx_csum
,
3550 .get_strings
= sky2_get_strings
,
3551 .get_coalesce
= sky2_get_coalesce
,
3552 .set_coalesce
= sky2_set_coalesce
,
3553 .get_ringparam
= sky2_get_ringparam
,
3554 .set_ringparam
= sky2_set_ringparam
,
3555 .get_pauseparam
= sky2_get_pauseparam
,
3556 .set_pauseparam
= sky2_set_pauseparam
,
3557 .phys_id
= sky2_phys_id
,
3558 .get_stats_count
= sky2_get_stats_count
,
3559 .get_ethtool_stats
= sky2_get_ethtool_stats
,
3560 .get_perm_addr
= ethtool_op_get_perm_addr
,
3563 #ifdef CONFIG_SKY2_DEBUG
3565 static struct dentry
*sky2_debug
;
3567 static int sky2_debug_show(struct seq_file
*seq
, void *v
)
3569 struct net_device
*dev
= seq
->private;
3570 const struct sky2_port
*sky2
= netdev_priv(dev
);
3571 const struct sky2_hw
*hw
= sky2
->hw
;
3572 unsigned port
= sky2
->port
;
3576 if (!netif_running(dev
))
3579 seq_printf(seq
, "IRQ src=%x mask=%x control=%x\n",
3580 sky2_read32(hw
, B0_ISRC
),
3581 sky2_read32(hw
, B0_IMSK
),
3582 sky2_read32(hw
, B0_Y2_SP_ICR
));
3584 netif_poll_disable(hw
->dev
[0]);
3585 last
= sky2_read16(hw
, STAT_PUT_IDX
);
3587 if (hw
->st_idx
== last
)
3588 seq_puts(seq
, "Status ring (empty)\n");
3590 seq_puts(seq
, "Status ring\n");
3591 for (idx
= hw
->st_idx
; idx
!= last
&& idx
< STATUS_RING_SIZE
;
3592 idx
= RING_NEXT(idx
, STATUS_RING_SIZE
)) {
3593 const struct sky2_status_le
*le
= hw
->st_le
+ idx
;
3594 seq_printf(seq
, "[%d] %#x %d %#x\n",
3595 idx
, le
->opcode
, le
->length
, le
->status
);
3597 seq_puts(seq
, "\n");
3600 seq_printf(seq
, "Tx ring pending=%u...%u report=%d done=%d\n",
3601 sky2
->tx_cons
, sky2
->tx_prod
,
3602 sky2_read16(hw
, port
== 0 ? STAT_TXA1_RIDX
: STAT_TXA2_RIDX
),
3603 sky2_read16(hw
, Q_ADDR(txqaddr
[port
], Q_DONE
)));
3605 /* Dump contents of tx ring */
3607 for (idx
= sky2
->tx_next
; idx
!= sky2
->tx_prod
&& idx
< TX_RING_SIZE
;
3608 idx
= RING_NEXT(idx
, TX_RING_SIZE
)) {
3609 const struct sky2_tx_le
*le
= sky2
->tx_le
+ idx
;
3610 u32 a
= le32_to_cpu(le
->addr
);
3613 seq_printf(seq
, "%u:", idx
);
3616 switch(le
->opcode
& ~HW_OWNER
) {
3618 seq_printf(seq
, " %#x:", a
);
3621 seq_printf(seq
, " mtu=%d", a
);
3624 seq_printf(seq
, " vlan=%d", be16_to_cpu(le
->length
));
3627 seq_printf(seq
, " csum=%#x", a
);
3630 seq_printf(seq
, " tso=%#x(%d)", a
, le16_to_cpu(le
->length
));
3633 seq_printf(seq
, " %#x(%d)", a
, le16_to_cpu(le
->length
));
3636 seq_printf(seq
, " frag=%#x(%d)", a
, le16_to_cpu(le
->length
));
3639 seq_printf(seq
, " op=%#x,%#x(%d)", le
->opcode
,
3640 a
, le16_to_cpu(le
->length
));
3643 if (le
->ctrl
& EOP
) {
3644 seq_putc(seq
, '\n');
3649 seq_printf(seq
, "\nRx ring hw get=%d put=%d last=%d\n",
3650 sky2_read16(hw
, Y2_QADDR(rxqaddr
[port
], PREF_UNIT_GET_IDX
)),
3651 last
= sky2_read16(hw
, Y2_QADDR(rxqaddr
[port
], PREF_UNIT_PUT_IDX
)),
3652 sky2_read16(hw
, Y2_QADDR(rxqaddr
[port
], PREF_UNIT_LAST_IDX
)));
3654 netif_poll_enable(hw
->dev
[0]);
3658 static int sky2_debug_open(struct inode
*inode
, struct file
*file
)
3660 return single_open(file
, sky2_debug_show
, inode
->i_private
);
3663 static const struct file_operations sky2_debug_fops
= {
3664 .owner
= THIS_MODULE
,
3665 .open
= sky2_debug_open
,
3667 .llseek
= seq_lseek
,
3668 .release
= single_release
,
3672 * Use network device events to create/remove/rename
3673 * debugfs file entries
3675 static int sky2_device_event(struct notifier_block
*unused
,
3676 unsigned long event
, void *ptr
)
3678 struct net_device
*dev
= ptr
;
3680 if (dev
->open
== sky2_up
) {
3681 struct sky2_port
*sky2
= netdev_priv(dev
);
3684 case NETDEV_CHANGENAME
:
3685 if (!netif_running(dev
))
3689 case NETDEV_GOING_DOWN
:
3690 if (sky2
->debugfs
) {
3691 printk(KERN_DEBUG PFX
"%s: remove debugfs\n",
3693 debugfs_remove(sky2
->debugfs
);
3694 sky2
->debugfs
= NULL
;
3697 if (event
!= NETDEV_CHANGENAME
)
3699 /* fallthrough for changename */
3703 d
= debugfs_create_file(dev
->name
, S_IRUGO
,
3706 if (d
== NULL
|| IS_ERR(d
))
3707 printk(KERN_INFO PFX
3708 "%s: debugfs create failed\n",
3720 static struct notifier_block sky2_notifier
= {
3721 .notifier_call
= sky2_device_event
,
3725 static __init
void sky2_debug_init(void)
3729 ent
= debugfs_create_dir("sky2", NULL
);
3730 if (!ent
|| IS_ERR(ent
))
3734 register_netdevice_notifier(&sky2_notifier
);
3737 static __exit
void sky2_debug_cleanup(void)
3740 unregister_netdevice_notifier(&sky2_notifier
);
3741 debugfs_remove(sky2_debug
);
3747 #define sky2_debug_init()
3748 #define sky2_debug_cleanup()
3752 /* Initialize network device */
3753 static __devinit
struct net_device
*sky2_init_netdev(struct sky2_hw
*hw
,
3755 int highmem
, int wol
)
3757 struct sky2_port
*sky2
;
3758 struct net_device
*dev
= alloc_etherdev(sizeof(*sky2
));
3761 dev_err(&hw
->pdev
->dev
, "etherdev alloc failed");
3765 SET_MODULE_OWNER(dev
);
3766 SET_NETDEV_DEV(dev
, &hw
->pdev
->dev
);
3767 dev
->irq
= hw
->pdev
->irq
;
3768 dev
->open
= sky2_up
;
3769 dev
->stop
= sky2_down
;
3770 dev
->do_ioctl
= sky2_ioctl
;
3771 dev
->hard_start_xmit
= sky2_xmit_frame
;
3772 dev
->get_stats
= sky2_get_stats
;
3773 dev
->set_multicast_list
= sky2_set_multicast
;
3774 dev
->set_mac_address
= sky2_set_mac_address
;
3775 dev
->change_mtu
= sky2_change_mtu
;
3776 SET_ETHTOOL_OPS(dev
, &sky2_ethtool_ops
);
3777 dev
->tx_timeout
= sky2_tx_timeout
;
3778 dev
->watchdog_timeo
= TX_WATCHDOG
;
3780 dev
->poll
= sky2_poll
;
3781 dev
->weight
= NAPI_WEIGHT
;
3782 #ifdef CONFIG_NET_POLL_CONTROLLER
3783 /* Network console (only works on port 0)
3784 * because netpoll makes assumptions about NAPI
3787 dev
->poll_controller
= sky2_netpoll
;
3790 sky2
= netdev_priv(dev
);
3793 sky2
->msg_enable
= netif_msg_init(debug
, default_msg
);
3795 /* Auto speed and flow control */
3796 sky2
->autoneg
= AUTONEG_ENABLE
;
3797 sky2
->flow_mode
= FC_BOTH
;
3801 sky2
->advertising
= sky2_supported_modes(hw
);
3805 spin_lock_init(&sky2
->phy_lock
);
3806 sky2
->tx_pending
= TX_DEF_PENDING
;
3807 sky2
->rx_pending
= RX_DEF_PENDING
;
3809 hw
->dev
[port
] = dev
;
3813 dev
->features
|= NETIF_F_TSO
| NETIF_F_IP_CSUM
| NETIF_F_SG
;
3815 dev
->features
|= NETIF_F_HIGHDMA
;
3817 #ifdef SKY2_VLAN_TAG_USED
3818 dev
->features
|= NETIF_F_HW_VLAN_TX
| NETIF_F_HW_VLAN_RX
;
3819 dev
->vlan_rx_register
= sky2_vlan_rx_register
;
3822 /* read the mac address */
3823 memcpy_fromio(dev
->dev_addr
, hw
->regs
+ B2_MAC_1
+ port
* 8, ETH_ALEN
);
3824 memcpy(dev
->perm_addr
, dev
->dev_addr
, dev
->addr_len
);
3829 static void __devinit
sky2_show_addr(struct net_device
*dev
)
3831 const struct sky2_port
*sky2
= netdev_priv(dev
);
3833 if (netif_msg_probe(sky2
))
3834 printk(KERN_INFO PFX
"%s: addr %02x:%02x:%02x:%02x:%02x:%02x\n",
3836 dev
->dev_addr
[0], dev
->dev_addr
[1], dev
->dev_addr
[2],
3837 dev
->dev_addr
[3], dev
->dev_addr
[4], dev
->dev_addr
[5]);
3840 /* Handle software interrupt used during MSI test */
3841 static irqreturn_t __devinit
sky2_test_intr(int irq
, void *dev_id
)
3843 struct sky2_hw
*hw
= dev_id
;
3844 u32 status
= sky2_read32(hw
, B0_Y2_SP_ISRC2
);
3849 if (status
& Y2_IS_IRQ_SW
) {
3851 wake_up(&hw
->msi_wait
);
3852 sky2_write8(hw
, B0_CTST
, CS_CL_SW_IRQ
);
3854 sky2_write32(hw
, B0_Y2_SP_ICR
, 2);
3859 /* Test interrupt path by forcing a a software IRQ */
3860 static int __devinit
sky2_test_msi(struct sky2_hw
*hw
)
3862 struct pci_dev
*pdev
= hw
->pdev
;
3865 init_waitqueue_head (&hw
->msi_wait
);
3867 sky2_write32(hw
, B0_IMSK
, Y2_IS_IRQ_SW
);
3869 err
= request_irq(pdev
->irq
, sky2_test_intr
, 0, DRV_NAME
, hw
);
3871 dev_err(&pdev
->dev
, "cannot assign irq %d\n", pdev
->irq
);
3875 sky2_write8(hw
, B0_CTST
, CS_ST_SW_IRQ
);
3876 sky2_read8(hw
, B0_CTST
);
3878 wait_event_timeout(hw
->msi_wait
, hw
->msi
, HZ
/10);
3881 /* MSI test failed, go back to INTx mode */
3882 dev_info(&pdev
->dev
, "No interrupt generated using MSI, "
3883 "switching to INTx mode.\n");
3886 sky2_write8(hw
, B0_CTST
, CS_CL_SW_IRQ
);
3889 sky2_write32(hw
, B0_IMSK
, 0);
3890 sky2_read32(hw
, B0_IMSK
);
3892 free_irq(pdev
->irq
, hw
);
3897 static int __devinit
pci_wake_enabled(struct pci_dev
*dev
)
3899 int pm
= pci_find_capability(dev
, PCI_CAP_ID_PM
);
3904 if (pci_read_config_word(dev
, pm
+ PCI_PM_CTRL
, &value
))
3906 return value
& PCI_PM_CTRL_PME_ENABLE
;
3909 static int __devinit
sky2_probe(struct pci_dev
*pdev
,
3910 const struct pci_device_id
*ent
)
3912 struct net_device
*dev
;
3914 int err
, using_dac
= 0, wol_default
;
3916 err
= pci_enable_device(pdev
);
3918 dev_err(&pdev
->dev
, "cannot enable PCI device\n");
3922 err
= pci_request_regions(pdev
, DRV_NAME
);
3924 dev_err(&pdev
->dev
, "cannot obtain PCI resources\n");
3925 goto err_out_disable
;
3928 pci_set_master(pdev
);
3930 if (sizeof(dma_addr_t
) > sizeof(u32
) &&
3931 !(err
= pci_set_dma_mask(pdev
, DMA_64BIT_MASK
))) {
3933 err
= pci_set_consistent_dma_mask(pdev
, DMA_64BIT_MASK
);
3935 dev_err(&pdev
->dev
, "unable to obtain 64 bit DMA "
3936 "for consistent allocations\n");
3937 goto err_out_free_regions
;
3940 err
= pci_set_dma_mask(pdev
, DMA_32BIT_MASK
);
3942 dev_err(&pdev
->dev
, "no usable DMA configuration\n");
3943 goto err_out_free_regions
;
3947 wol_default
= pci_wake_enabled(pdev
) ? WAKE_MAGIC
: 0;
3950 hw
= kzalloc(sizeof(*hw
), GFP_KERNEL
);
3952 dev_err(&pdev
->dev
, "cannot allocate hardware struct\n");
3953 goto err_out_free_regions
;
3958 hw
->regs
= ioremap_nocache(pci_resource_start(pdev
, 0), 0x4000);
3960 dev_err(&pdev
->dev
, "cannot map device registers\n");
3961 goto err_out_free_hw
;
3965 /* The sk98lin vendor driver uses hardware byte swapping but
3966 * this driver uses software swapping.
3970 reg
= sky2_pci_read32(hw
, PCI_DEV_REG2
);
3971 reg
&= ~PCI_REV_DESC
;
3972 sky2_pci_write32(hw
, PCI_DEV_REG2
, reg
);
3976 /* ring for status responses */
3977 hw
->st_le
= pci_alloc_consistent(hw
->pdev
, STATUS_LE_BYTES
,
3980 goto err_out_iounmap
;
3982 err
= sky2_init(hw
);
3984 goto err_out_iounmap
;
3986 dev_info(&pdev
->dev
, "v%s addr 0x%llx irq %d Yukon-%s (0x%x) rev %d\n",
3987 DRV_VERSION
, (unsigned long long)pci_resource_start(pdev
, 0),
3988 pdev
->irq
, yukon2_name
[hw
->chip_id
- CHIP_ID_YUKON_XL
],
3989 hw
->chip_id
, hw
->chip_rev
);
3993 dev
= sky2_init_netdev(hw
, 0, using_dac
, wol_default
);
3996 goto err_out_free_pci
;
3999 if (!disable_msi
&& pci_enable_msi(pdev
) == 0) {
4000 err
= sky2_test_msi(hw
);
4001 if (err
== -EOPNOTSUPP
)
4002 pci_disable_msi(pdev
);
4004 goto err_out_free_netdev
;
4007 err
= register_netdev(dev
);
4009 dev_err(&pdev
->dev
, "cannot register net device\n");
4010 goto err_out_free_netdev
;
4013 err
= request_irq(pdev
->irq
, sky2_intr
, hw
->msi
? 0 : IRQF_SHARED
,
4016 dev_err(&pdev
->dev
, "cannot assign irq %d\n", pdev
->irq
);
4017 goto err_out_unregister
;
4019 sky2_write32(hw
, B0_IMSK
, Y2_IS_BASE
);
4021 sky2_show_addr(dev
);
4023 if (hw
->ports
> 1) {
4024 struct net_device
*dev1
;
4026 dev1
= sky2_init_netdev(hw
, 1, using_dac
, wol_default
);
4028 dev_warn(&pdev
->dev
, "allocation for second device failed\n");
4029 else if ((err
= register_netdev(dev1
))) {
4030 dev_warn(&pdev
->dev
,
4031 "register of second port failed (%d)\n", err
);
4035 sky2_show_addr(dev1
);
4038 setup_timer(&hw
->idle_timer
, sky2_idle
, (unsigned long) hw
);
4039 INIT_WORK(&hw
->restart_work
, sky2_restart
);
4041 sky2_idle_start(hw
);
4043 pci_set_drvdata(pdev
, hw
);
4049 pci_disable_msi(pdev
);
4050 unregister_netdev(dev
);
4051 err_out_free_netdev
:
4054 sky2_write8(hw
, B0_CTST
, CS_RST_SET
);
4055 pci_free_consistent(hw
->pdev
, STATUS_LE_BYTES
, hw
->st_le
, hw
->st_dma
);
4060 err_out_free_regions
:
4061 pci_release_regions(pdev
);
4063 pci_disable_device(pdev
);
4065 pci_set_drvdata(pdev
, NULL
);
4069 static void __devexit
sky2_remove(struct pci_dev
*pdev
)
4071 struct sky2_hw
*hw
= pci_get_drvdata(pdev
);
4072 struct net_device
*dev0
, *dev1
;
4077 del_timer_sync(&hw
->idle_timer
);
4079 flush_scheduled_work();
4081 sky2_write32(hw
, B0_IMSK
, 0);
4082 synchronize_irq(hw
->pdev
->irq
);
4087 unregister_netdev(dev1
);
4088 unregister_netdev(dev0
);
4092 sky2_write16(hw
, B0_Y2LED
, LED_STAT_OFF
);
4093 sky2_write8(hw
, B0_CTST
, CS_RST_SET
);
4094 sky2_read8(hw
, B0_CTST
);
4096 free_irq(pdev
->irq
, hw
);
4098 pci_disable_msi(pdev
);
4099 pci_free_consistent(pdev
, STATUS_LE_BYTES
, hw
->st_le
, hw
->st_dma
);
4100 pci_release_regions(pdev
);
4101 pci_disable_device(pdev
);
4109 pci_set_drvdata(pdev
, NULL
);
4113 static int sky2_suspend(struct pci_dev
*pdev
, pm_message_t state
)
4115 struct sky2_hw
*hw
= pci_get_drvdata(pdev
);
4121 del_timer_sync(&hw
->idle_timer
);
4122 netif_poll_disable(hw
->dev
[0]);
4124 for (i
= 0; i
< hw
->ports
; i
++) {
4125 struct net_device
*dev
= hw
->dev
[i
];
4126 struct sky2_port
*sky2
= netdev_priv(dev
);
4128 if (netif_running(dev
))
4132 sky2_wol_init(sky2
);
4137 sky2_write32(hw
, B0_IMSK
, 0);
4140 pci_save_state(pdev
);
4141 pci_enable_wake(pdev
, pci_choose_state(pdev
, state
), wol
);
4142 pci_set_power_state(pdev
, pci_choose_state(pdev
, state
));
4147 static int sky2_resume(struct pci_dev
*pdev
)
4149 struct sky2_hw
*hw
= pci_get_drvdata(pdev
);
4155 err
= pci_set_power_state(pdev
, PCI_D0
);
4159 err
= pci_restore_state(pdev
);
4163 pci_enable_wake(pdev
, PCI_D0
, 0);
4165 /* Re-enable all clocks */
4166 if (hw
->chip_id
== CHIP_ID_YUKON_EX
|| hw
->chip_id
== CHIP_ID_YUKON_EC_U
)
4167 sky2_pci_write32(hw
, PCI_DEV_REG3
, 0);
4171 sky2_write32(hw
, B0_IMSK
, Y2_IS_BASE
);
4173 for (i
= 0; i
< hw
->ports
; i
++) {
4174 struct net_device
*dev
= hw
->dev
[i
];
4175 if (netif_running(dev
)) {
4178 printk(KERN_ERR PFX
"%s: could not up: %d\n",
4186 netif_poll_enable(hw
->dev
[0]);
4187 sky2_idle_start(hw
);
4190 dev_err(&pdev
->dev
, "resume failed (%d)\n", err
);
4191 pci_disable_device(pdev
);
4196 static void sky2_shutdown(struct pci_dev
*pdev
)
4198 struct sky2_hw
*hw
= pci_get_drvdata(pdev
);
4204 del_timer_sync(&hw
->idle_timer
);
4205 netif_poll_disable(hw
->dev
[0]);
4207 for (i
= 0; i
< hw
->ports
; i
++) {
4208 struct net_device
*dev
= hw
->dev
[i
];
4209 struct sky2_port
*sky2
= netdev_priv(dev
);
4213 sky2_wol_init(sky2
);
4220 pci_enable_wake(pdev
, PCI_D3hot
, wol
);
4221 pci_enable_wake(pdev
, PCI_D3cold
, wol
);
4223 pci_disable_device(pdev
);
4224 pci_set_power_state(pdev
, PCI_D3hot
);
4228 static struct pci_driver sky2_driver
= {
4230 .id_table
= sky2_id_table
,
4231 .probe
= sky2_probe
,
4232 .remove
= __devexit_p(sky2_remove
),
4234 .suspend
= sky2_suspend
,
4235 .resume
= sky2_resume
,
4237 .shutdown
= sky2_shutdown
,
4240 static int __init
sky2_init_module(void)
4243 return pci_register_driver(&sky2_driver
);
4246 static void __exit
sky2_cleanup_module(void)
4248 pci_unregister_driver(&sky2_driver
);
4249 sky2_debug_cleanup();
4252 module_init(sky2_init_module
);
4253 module_exit(sky2_cleanup_module
);
4255 MODULE_DESCRIPTION("Marvell Yukon 2 Gigabit Ethernet driver");
4256 MODULE_AUTHOR("Stephen Hemminger <shemminger@linux-foundation.org>");
4257 MODULE_LICENSE("GPL");
4258 MODULE_VERSION(DRV_VERSION
);