4 * Copyright (c) 2004-2007 Reyk Floeter <reyk@openbsd.org>
5 * Copyright (c) 2006-2009 Nick Kossifidis <mickflemm@gmail.com>
6 * Copyright (c) 2007-2008 Jiri Slaby <jirislaby@gmail.com>
7 * Copyright (c) 2008-2009 Felix Fietkau <nbd@openwrt.org>
9 * Permission to use, copy, modify, and distribute this software for any
10 * purpose with or without fee is hereby granted, provided that the above
11 * copyright notice and this permission notice appear in all copies.
13 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
14 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
15 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
16 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
17 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
18 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
19 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
23 #include <linux/delay.h>
24 #include <linux/slab.h>
38 * Get the PHY Chip revision
40 u16
ath5k_hw_radio_revision(struct ath5k_hw
*ah
, unsigned int chan
)
47 * Set the radio chip access register
51 ath5k_hw_reg_write(ah
, AR5K_PHY_SHIFT_2GHZ
, AR5K_PHY(0));
54 ath5k_hw_reg_write(ah
, AR5K_PHY_SHIFT_5GHZ
, AR5K_PHY(0));
62 /* ...wait until PHY is ready and read the selected radio revision */
63 ath5k_hw_reg_write(ah
, 0x00001c16, AR5K_PHY(0x34));
65 for (i
= 0; i
< 8; i
++)
66 ath5k_hw_reg_write(ah
, 0x00010000, AR5K_PHY(0x20));
68 if (ah
->ah_version
== AR5K_AR5210
) {
69 srev
= ath5k_hw_reg_read(ah
, AR5K_PHY(256) >> 28) & 0xf;
70 ret
= (u16
)ath5k_hw_bitswap(srev
, 4) + 1;
72 srev
= (ath5k_hw_reg_read(ah
, AR5K_PHY(0x100)) >> 24) & 0xff;
73 ret
= (u16
)ath5k_hw_bitswap(((srev
& 0xf0) >> 4) |
74 ((srev
& 0x0f) << 4), 8);
77 /* Reset to the 5GHz mode */
78 ath5k_hw_reg_write(ah
, AR5K_PHY_SHIFT_5GHZ
, AR5K_PHY(0));
84 * Check if a channel is supported
86 bool ath5k_channel_ok(struct ath5k_hw
*ah
, u16 freq
, unsigned int flags
)
88 /* Check if the channel is in our supported range */
89 if (flags
& CHANNEL_2GHZ
) {
90 if ((freq
>= ah
->ah_capabilities
.cap_range
.range_2ghz_min
) &&
91 (freq
<= ah
->ah_capabilities
.cap_range
.range_2ghz_max
))
93 } else if (flags
& CHANNEL_5GHZ
)
94 if ((freq
>= ah
->ah_capabilities
.cap_range
.range_5ghz_min
) &&
95 (freq
<= ah
->ah_capabilities
.cap_range
.range_5ghz_max
))
101 bool ath5k_hw_chan_has_spur_noise(struct ath5k_hw
*ah
,
102 struct ieee80211_channel
*channel
)
106 if ((ah
->ah_radio
== AR5K_RF5112
) ||
107 (ah
->ah_radio
== AR5K_RF5413
) ||
108 (ah
->ah_mac_version
== (AR5K_SREV_AR2417
>> 4)))
113 if ((channel
->center_freq
% refclk_freq
!= 0) &&
114 ((channel
->center_freq
% refclk_freq
< 10) ||
115 (channel
->center_freq
% refclk_freq
> 22)))
122 * Used to modify RF Banks before writing them to AR5K_RF_BUFFER
124 static unsigned int ath5k_hw_rfb_op(struct ath5k_hw
*ah
,
125 const struct ath5k_rf_reg
*rf_regs
,
126 u32 val
, u8 reg_id
, bool set
)
128 const struct ath5k_rf_reg
*rfreg
= NULL
;
129 u8 offset
, bank
, num_bits
, col
, position
;
131 u32 mask
, data
, last_bit
, bits_shifted
, first_bit
;
137 rfb
= ah
->ah_rf_banks
;
139 for (i
= 0; i
< ah
->ah_rf_regs_count
; i
++) {
140 if (rf_regs
[i
].index
== reg_id
) {
146 if (rfb
== NULL
|| rfreg
== NULL
) {
147 ATH5K_PRINTF("Rf register not found!\n");
148 /* should not happen */
153 num_bits
= rfreg
->field
.len
;
154 first_bit
= rfreg
->field
.pos
;
155 col
= rfreg
->field
.col
;
157 /* first_bit is an offset from bank's
158 * start. Since we have all banks on
159 * the same array, we use this offset
160 * to mark each bank's start */
161 offset
= ah
->ah_offset
[bank
];
164 if (!(col
<= 3 && num_bits
<= 32 && first_bit
+ num_bits
<= 319)) {
165 ATH5K_PRINTF("invalid values at offset %u\n", offset
);
169 entry
= ((first_bit
- 1) / 8) + offset
;
170 position
= (first_bit
- 1) % 8;
173 data
= ath5k_hw_bitswap(val
, num_bits
);
175 for (bits_shifted
= 0, bits_left
= num_bits
; bits_left
> 0;
176 position
= 0, entry
++) {
178 last_bit
= (position
+ bits_left
> 8) ? 8 :
179 position
+ bits_left
;
181 mask
= (((1 << last_bit
) - 1) ^ ((1 << position
) - 1)) <<
186 rfb
[entry
] |= ((data
<< position
) << (col
* 8)) & mask
;
187 data
>>= (8 - position
);
189 data
|= (((rfb
[entry
] & mask
) >> (col
* 8)) >> position
)
191 bits_shifted
+= last_bit
- position
;
194 bits_left
-= 8 - position
;
197 data
= set
? 1 : ath5k_hw_bitswap(data
, num_bits
);
203 * ath5k_hw_write_ofdm_timings - set OFDM timings on AR5212
205 * @ah: the &struct ath5k_hw
206 * @channel: the currently set channel upon reset
208 * Write the delta slope coefficient (used on pilot tracking ?) for OFDM
209 * operation on the AR5212 upon reset. This is a helper for ath5k_hw_phy_init.
211 * Since delta slope is floating point we split it on its exponent and
212 * mantissa and provide these values on hw.
214 * For more infos i think this patent is related
215 * http://www.freepatentsonline.com/7184495.html
217 static inline int ath5k_hw_write_ofdm_timings(struct ath5k_hw
*ah
,
218 struct ieee80211_channel
*channel
)
220 /* Get exponent and mantissa and set it */
221 u32 coef_scaled
, coef_exp
, coef_man
,
222 ds_coef_exp
, ds_coef_man
, clock
;
224 BUG_ON(!(ah
->ah_version
== AR5K_AR5212
) ||
225 !(channel
->hw_value
& CHANNEL_OFDM
));
228 * ALGO: coef = (5 * clock / carrier_freq) / 2
229 * we scale coef by shifting clock value by 24 for
230 * better precision since we use integers */
231 switch (ah
->ah_bwmode
) {
232 case AR5K_BWMODE_40MHZ
:
235 case AR5K_BWMODE_10MHZ
:
238 case AR5K_BWMODE_5MHZ
:
245 coef_scaled
= ((5 * (clock
<< 24)) / 2) / channel
->center_freq
;
248 * ALGO: coef_exp = 14 - highest set bit position */
249 coef_exp
= ilog2(coef_scaled
);
251 /* Doesn't make sense if it's zero*/
252 if (!coef_scaled
|| !coef_exp
)
255 /* Note: we've shifted coef_scaled by 24 */
256 coef_exp
= 14 - (coef_exp
- 24);
259 /* Get mantissa (significant digits)
260 * ALGO: coef_mant = floor(coef_scaled* 2^coef_exp+0.5) */
261 coef_man
= coef_scaled
+
262 (1 << (24 - coef_exp
- 1));
264 /* Calculate delta slope coefficient exponent
265 * and mantissa (remove scaling) and set them on hw */
266 ds_coef_man
= coef_man
>> (24 - coef_exp
);
267 ds_coef_exp
= coef_exp
- 16;
269 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_TIMING_3
,
270 AR5K_PHY_TIMING_3_DSC_MAN
, ds_coef_man
);
271 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_TIMING_3
,
272 AR5K_PHY_TIMING_3_DSC_EXP
, ds_coef_exp
);
277 int ath5k_hw_phy_disable(struct ath5k_hw
*ah
)
280 ath5k_hw_reg_write(ah
, AR5K_PHY_ACT_DISABLE
, AR5K_PHY_ACT
);
286 * Wait for synth to settle
288 static void ath5k_hw_wait_for_synth(struct ath5k_hw
*ah
,
289 struct ieee80211_channel
*channel
)
292 * On 5211+ read activation -> rx delay
293 * and use it (100ns steps).
295 if (ah
->ah_version
!= AR5K_AR5210
) {
297 delay
= ath5k_hw_reg_read(ah
, AR5K_PHY_RX_DELAY
) &
299 delay
= (channel
->hw_value
& CHANNEL_CCK
) ?
300 ((delay
<< 2) / 22) : (delay
/ 10);
301 if (ah
->ah_bwmode
== AR5K_BWMODE_10MHZ
)
303 if (ah
->ah_bwmode
== AR5K_BWMODE_5MHZ
)
305 /* XXX: /2 on turbo ? Let's be safe
314 /**********************\
315 * RF Gain optimization *
316 \**********************/
319 * This code is used to optimize RF gain on different environments
320 * (temperature mostly) based on feedback from a power detector.
322 * It's only used on RF5111 and RF5112, later RF chips seem to have
323 * auto adjustment on hw -notice they have a much smaller BANK 7 and
324 * no gain optimization ladder-.
326 * For more infos check out this patent doc
327 * http://www.freepatentsonline.com/7400691.html
329 * This paper describes power drops as seen on the receiver due to
331 * http://www.cnri.dit.ie/publications/ICT08%20-%20Practical%20Issues
332 * %20of%20Power%20Control.pdf
334 * And this is the MadWiFi bug entry related to the above
335 * http://madwifi-project.org/ticket/1659
336 * with various measurements and diagrams
338 * TODO: Deal with power drops due to probes by setting an appropriate
339 * tx power on the probe packets ! Make this part of the calibration process.
342 /* Initialize ah_gain during attach */
343 int ath5k_hw_rfgain_opt_init(struct ath5k_hw
*ah
)
345 /* Initialize the gain optimization values */
346 switch (ah
->ah_radio
) {
348 ah
->ah_gain
.g_step_idx
= rfgain_opt_5111
.go_default
;
349 ah
->ah_gain
.g_low
= 20;
350 ah
->ah_gain
.g_high
= 35;
351 ah
->ah_gain
.g_state
= AR5K_RFGAIN_ACTIVE
;
354 ah
->ah_gain
.g_step_idx
= rfgain_opt_5112
.go_default
;
355 ah
->ah_gain
.g_low
= 20;
356 ah
->ah_gain
.g_high
= 85;
357 ah
->ah_gain
.g_state
= AR5K_RFGAIN_ACTIVE
;
366 /* Schedule a gain probe check on the next transmitted packet.
367 * That means our next packet is going to be sent with lower
368 * tx power and a Peak to Average Power Detector (PAPD) will try
369 * to measure the gain.
371 * XXX: How about forcing a tx packet (bypassing PCU arbitrator etc)
372 * just after we enable the probe so that we don't mess with
373 * standard traffic ? Maybe it's time to use sw interrupts and
374 * a probe tasklet !!!
376 static void ath5k_hw_request_rfgain_probe(struct ath5k_hw
*ah
)
379 /* Skip if gain calibration is inactive or
380 * we already handle a probe request */
381 if (ah
->ah_gain
.g_state
!= AR5K_RFGAIN_ACTIVE
)
384 /* Send the packet with 2dB below max power as
385 * patent doc suggest */
386 ath5k_hw_reg_write(ah
, AR5K_REG_SM(ah
->ah_txpower
.txp_ofdm
- 4,
387 AR5K_PHY_PAPD_PROBE_TXPOWER
) |
388 AR5K_PHY_PAPD_PROBE_TX_NEXT
, AR5K_PHY_PAPD_PROBE
);
390 ah
->ah_gain
.g_state
= AR5K_RFGAIN_READ_REQUESTED
;
394 /* Calculate gain_F measurement correction
395 * based on the current step for RF5112 rev. 2 */
396 static u32
ath5k_hw_rf_gainf_corr(struct ath5k_hw
*ah
)
400 const struct ath5k_gain_opt
*go
;
401 const struct ath5k_gain_opt_step
*g_step
;
402 const struct ath5k_rf_reg
*rf_regs
;
404 /* Only RF5112 Rev. 2 supports it */
405 if ((ah
->ah_radio
!= AR5K_RF5112
) ||
406 (ah
->ah_radio_5ghz_revision
<= AR5K_SREV_RAD_5112A
))
409 go
= &rfgain_opt_5112
;
410 rf_regs
= rf_regs_5112a
;
411 ah
->ah_rf_regs_count
= ARRAY_SIZE(rf_regs_5112a
);
413 g_step
= &go
->go_step
[ah
->ah_gain
.g_step_idx
];
415 if (ah
->ah_rf_banks
== NULL
)
418 rf
= ah
->ah_rf_banks
;
419 ah
->ah_gain
.g_f_corr
= 0;
421 /* No VGA (Variable Gain Amplifier) override, skip */
422 if (ath5k_hw_rfb_op(ah
, rf_regs
, 0, AR5K_RF_MIXVGA_OVR
, false) != 1)
425 /* Mix gain stepping */
426 step
= ath5k_hw_rfb_op(ah
, rf_regs
, 0, AR5K_RF_MIXGAIN_STEP
, false);
428 /* Mix gain override */
429 mix
= g_step
->gos_param
[0];
433 ah
->ah_gain
.g_f_corr
= step
* 2;
436 ah
->ah_gain
.g_f_corr
= (step
- 5) * 2;
439 ah
->ah_gain
.g_f_corr
= step
;
442 ah
->ah_gain
.g_f_corr
= 0;
446 return ah
->ah_gain
.g_f_corr
;
449 /* Check if current gain_F measurement is in the range of our
450 * power detector windows. If we get a measurement outside range
451 * we know it's not accurate (detectors can't measure anything outside
452 * their detection window) so we must ignore it */
453 static bool ath5k_hw_rf_check_gainf_readback(struct ath5k_hw
*ah
)
455 const struct ath5k_rf_reg
*rf_regs
;
456 u32 step
, mix_ovr
, level
[4];
459 if (ah
->ah_rf_banks
== NULL
)
462 rf
= ah
->ah_rf_banks
;
464 if (ah
->ah_radio
== AR5K_RF5111
) {
466 rf_regs
= rf_regs_5111
;
467 ah
->ah_rf_regs_count
= ARRAY_SIZE(rf_regs_5111
);
469 step
= ath5k_hw_rfb_op(ah
, rf_regs
, 0, AR5K_RF_RFGAIN_STEP
,
473 level
[1] = (step
== 63) ? 50 : step
+ 4;
474 level
[2] = (step
!= 63) ? 64 : level
[0];
475 level
[3] = level
[2] + 50;
477 ah
->ah_gain
.g_high
= level
[3] -
478 (step
== 63 ? AR5K_GAIN_DYN_ADJUST_HI_MARGIN
: -5);
479 ah
->ah_gain
.g_low
= level
[0] +
480 (step
== 63 ? AR5K_GAIN_DYN_ADJUST_LO_MARGIN
: 0);
483 rf_regs
= rf_regs_5112
;
484 ah
->ah_rf_regs_count
= ARRAY_SIZE(rf_regs_5112
);
486 mix_ovr
= ath5k_hw_rfb_op(ah
, rf_regs
, 0, AR5K_RF_MIXVGA_OVR
,
489 level
[0] = level
[2] = 0;
492 level
[1] = level
[3] = 83;
494 level
[1] = level
[3] = 107;
495 ah
->ah_gain
.g_high
= 55;
499 return (ah
->ah_gain
.g_current
>= level
[0] &&
500 ah
->ah_gain
.g_current
<= level
[1]) ||
501 (ah
->ah_gain
.g_current
>= level
[2] &&
502 ah
->ah_gain
.g_current
<= level
[3]);
505 /* Perform gain_F adjustment by choosing the right set
506 * of parameters from RF gain optimization ladder */
507 static s8
ath5k_hw_rf_gainf_adjust(struct ath5k_hw
*ah
)
509 const struct ath5k_gain_opt
*go
;
510 const struct ath5k_gain_opt_step
*g_step
;
513 switch (ah
->ah_radio
) {
515 go
= &rfgain_opt_5111
;
518 go
= &rfgain_opt_5112
;
524 g_step
= &go
->go_step
[ah
->ah_gain
.g_step_idx
];
526 if (ah
->ah_gain
.g_current
>= ah
->ah_gain
.g_high
) {
528 /* Reached maximum */
529 if (ah
->ah_gain
.g_step_idx
== 0)
532 for (ah
->ah_gain
.g_target
= ah
->ah_gain
.g_current
;
533 ah
->ah_gain
.g_target
>= ah
->ah_gain
.g_high
&&
534 ah
->ah_gain
.g_step_idx
> 0;
535 g_step
= &go
->go_step
[ah
->ah_gain
.g_step_idx
])
536 ah
->ah_gain
.g_target
-= 2 *
537 (go
->go_step
[--(ah
->ah_gain
.g_step_idx
)].gos_gain
-
544 if (ah
->ah_gain
.g_current
<= ah
->ah_gain
.g_low
) {
546 /* Reached minimum */
547 if (ah
->ah_gain
.g_step_idx
== (go
->go_steps_count
- 1))
550 for (ah
->ah_gain
.g_target
= ah
->ah_gain
.g_current
;
551 ah
->ah_gain
.g_target
<= ah
->ah_gain
.g_low
&&
552 ah
->ah_gain
.g_step_idx
< go
->go_steps_count
- 1;
553 g_step
= &go
->go_step
[ah
->ah_gain
.g_step_idx
])
554 ah
->ah_gain
.g_target
-= 2 *
555 (go
->go_step
[++ah
->ah_gain
.g_step_idx
].gos_gain
-
563 ATH5K_DBG(ah
->ah_sc
, ATH5K_DEBUG_CALIBRATE
,
564 "ret %d, gain step %u, current gain %u, target gain %u\n",
565 ret
, ah
->ah_gain
.g_step_idx
, ah
->ah_gain
.g_current
,
566 ah
->ah_gain
.g_target
);
571 /* Main callback for thermal RF gain calibration engine
572 * Check for a new gain reading and schedule an adjustment
575 * TODO: Use sw interrupt to schedule reset if gain_F needs
577 enum ath5k_rfgain
ath5k_hw_gainf_calibrate(struct ath5k_hw
*ah
)
580 struct ath5k_eeprom_info
*ee
= &ah
->ah_capabilities
.cap_eeprom
;
582 if (ah
->ah_rf_banks
== NULL
||
583 ah
->ah_gain
.g_state
== AR5K_RFGAIN_INACTIVE
)
584 return AR5K_RFGAIN_INACTIVE
;
586 /* No check requested, either engine is inactive
587 * or an adjustment is already requested */
588 if (ah
->ah_gain
.g_state
!= AR5K_RFGAIN_READ_REQUESTED
)
591 /* Read the PAPD (Peak to Average Power Detector)
593 data
= ath5k_hw_reg_read(ah
, AR5K_PHY_PAPD_PROBE
);
595 /* No probe is scheduled, read gain_F measurement */
596 if (!(data
& AR5K_PHY_PAPD_PROBE_TX_NEXT
)) {
597 ah
->ah_gain
.g_current
= data
>> AR5K_PHY_PAPD_PROBE_GAINF_S
;
598 type
= AR5K_REG_MS(data
, AR5K_PHY_PAPD_PROBE_TYPE
);
600 /* If tx packet is CCK correct the gain_F measurement
601 * by cck ofdm gain delta */
602 if (type
== AR5K_PHY_PAPD_PROBE_TYPE_CCK
) {
603 if (ah
->ah_radio_5ghz_revision
>= AR5K_SREV_RAD_5112A
)
604 ah
->ah_gain
.g_current
+=
605 ee
->ee_cck_ofdm_gain_delta
;
607 ah
->ah_gain
.g_current
+=
608 AR5K_GAIN_CCK_PROBE_CORR
;
611 /* Further correct gain_F measurement for
613 if (ah
->ah_radio_5ghz_revision
>= AR5K_SREV_RAD_5112A
) {
614 ath5k_hw_rf_gainf_corr(ah
);
615 ah
->ah_gain
.g_current
=
616 ah
->ah_gain
.g_current
>= ah
->ah_gain
.g_f_corr
?
617 (ah
->ah_gain
.g_current
- ah
->ah_gain
.g_f_corr
) :
621 /* Check if measurement is ok and if we need
622 * to adjust gain, schedule a gain adjustment,
623 * else switch back to the active state */
624 if (ath5k_hw_rf_check_gainf_readback(ah
) &&
625 AR5K_GAIN_CHECK_ADJUST(&ah
->ah_gain
) &&
626 ath5k_hw_rf_gainf_adjust(ah
)) {
627 ah
->ah_gain
.g_state
= AR5K_RFGAIN_NEED_CHANGE
;
629 ah
->ah_gain
.g_state
= AR5K_RFGAIN_ACTIVE
;
634 return ah
->ah_gain
.g_state
;
637 /* Write initial RF gain table to set the RF sensitivity
638 * this one works on all RF chips and has nothing to do
639 * with gain_F calibration */
640 static int ath5k_hw_rfgain_init(struct ath5k_hw
*ah
, enum ieee80211_band band
)
642 const struct ath5k_ini_rfgain
*ath5k_rfg
;
643 unsigned int i
, size
, index
;
645 switch (ah
->ah_radio
) {
647 ath5k_rfg
= rfgain_5111
;
648 size
= ARRAY_SIZE(rfgain_5111
);
651 ath5k_rfg
= rfgain_5112
;
652 size
= ARRAY_SIZE(rfgain_5112
);
655 ath5k_rfg
= rfgain_2413
;
656 size
= ARRAY_SIZE(rfgain_2413
);
659 ath5k_rfg
= rfgain_2316
;
660 size
= ARRAY_SIZE(rfgain_2316
);
663 ath5k_rfg
= rfgain_5413
;
664 size
= ARRAY_SIZE(rfgain_5413
);
668 ath5k_rfg
= rfgain_2425
;
669 size
= ARRAY_SIZE(rfgain_2425
);
675 index
= (band
== IEEE80211_BAND_2GHZ
) ? 1 : 0;
677 for (i
= 0; i
< size
; i
++) {
679 ath5k_hw_reg_write(ah
, ath5k_rfg
[i
].rfg_value
[index
],
680 (u32
)ath5k_rfg
[i
].rfg_register
);
688 /********************\
689 * RF Registers setup *
690 \********************/
693 * Setup RF registers by writing RF buffer on hw
695 static int ath5k_hw_rfregs_init(struct ath5k_hw
*ah
,
696 struct ieee80211_channel
*channel
, unsigned int mode
)
698 const struct ath5k_rf_reg
*rf_regs
;
699 const struct ath5k_ini_rfbuffer
*ini_rfb
;
700 const struct ath5k_gain_opt
*go
= NULL
;
701 const struct ath5k_gain_opt_step
*g_step
;
702 struct ath5k_eeprom_info
*ee
= &ah
->ah_capabilities
.cap_eeprom
;
705 int i
, obdb
= -1, bank
= -1;
707 switch (ah
->ah_radio
) {
709 rf_regs
= rf_regs_5111
;
710 ah
->ah_rf_regs_count
= ARRAY_SIZE(rf_regs_5111
);
712 ah
->ah_rf_banks_size
= ARRAY_SIZE(rfb_5111
);
713 go
= &rfgain_opt_5111
;
716 if (ah
->ah_radio_5ghz_revision
>= AR5K_SREV_RAD_5112A
) {
717 rf_regs
= rf_regs_5112a
;
718 ah
->ah_rf_regs_count
= ARRAY_SIZE(rf_regs_5112a
);
720 ah
->ah_rf_banks_size
= ARRAY_SIZE(rfb_5112a
);
722 rf_regs
= rf_regs_5112
;
723 ah
->ah_rf_regs_count
= ARRAY_SIZE(rf_regs_5112
);
725 ah
->ah_rf_banks_size
= ARRAY_SIZE(rfb_5112
);
727 go
= &rfgain_opt_5112
;
730 rf_regs
= rf_regs_2413
;
731 ah
->ah_rf_regs_count
= ARRAY_SIZE(rf_regs_2413
);
733 ah
->ah_rf_banks_size
= ARRAY_SIZE(rfb_2413
);
736 rf_regs
= rf_regs_2316
;
737 ah
->ah_rf_regs_count
= ARRAY_SIZE(rf_regs_2316
);
739 ah
->ah_rf_banks_size
= ARRAY_SIZE(rfb_2316
);
742 rf_regs
= rf_regs_5413
;
743 ah
->ah_rf_regs_count
= ARRAY_SIZE(rf_regs_5413
);
745 ah
->ah_rf_banks_size
= ARRAY_SIZE(rfb_5413
);
748 rf_regs
= rf_regs_2425
;
749 ah
->ah_rf_regs_count
= ARRAY_SIZE(rf_regs_2425
);
751 ah
->ah_rf_banks_size
= ARRAY_SIZE(rfb_2317
);
754 rf_regs
= rf_regs_2425
;
755 ah
->ah_rf_regs_count
= ARRAY_SIZE(rf_regs_2425
);
756 if (ah
->ah_mac_srev
< AR5K_SREV_AR2417
) {
758 ah
->ah_rf_banks_size
= ARRAY_SIZE(rfb_2425
);
761 ah
->ah_rf_banks_size
= ARRAY_SIZE(rfb_2417
);
768 /* If it's the first time we set RF buffer, allocate
769 * ah->ah_rf_banks based on ah->ah_rf_banks_size
771 if (ah
->ah_rf_banks
== NULL
) {
772 ah
->ah_rf_banks
= kmalloc(sizeof(u32
) * ah
->ah_rf_banks_size
,
774 if (ah
->ah_rf_banks
== NULL
) {
775 ATH5K_ERR(ah
->ah_sc
, "out of memory\n");
780 /* Copy values to modify them */
781 rfb
= ah
->ah_rf_banks
;
783 for (i
= 0; i
< ah
->ah_rf_banks_size
; i
++) {
784 if (ini_rfb
[i
].rfb_bank
>= AR5K_MAX_RF_BANKS
) {
785 ATH5K_ERR(ah
->ah_sc
, "invalid bank\n");
789 /* Bank changed, write down the offset */
790 if (bank
!= ini_rfb
[i
].rfb_bank
) {
791 bank
= ini_rfb
[i
].rfb_bank
;
792 ah
->ah_offset
[bank
] = i
;
795 rfb
[i
] = ini_rfb
[i
].rfb_mode_data
[mode
];
798 /* Set Output and Driver bias current (OB/DB) */
799 if (channel
->hw_value
& CHANNEL_2GHZ
) {
801 if (channel
->hw_value
& CHANNEL_CCK
)
802 ee_mode
= AR5K_EEPROM_MODE_11B
;
804 ee_mode
= AR5K_EEPROM_MODE_11G
;
806 /* For RF511X/RF211X combination we
807 * use b_OB and b_DB parameters stored
808 * in eeprom on ee->ee_ob[ee_mode][0]
810 * For all other chips we use OB/DB for 2GHz
811 * stored in the b/g modal section just like
812 * 802.11a on ee->ee_ob[ee_mode][1] */
813 if ((ah
->ah_radio
== AR5K_RF5111
) ||
814 (ah
->ah_radio
== AR5K_RF5112
))
819 ath5k_hw_rfb_op(ah
, rf_regs
, ee
->ee_ob
[ee_mode
][obdb
],
820 AR5K_RF_OB_2GHZ
, true);
822 ath5k_hw_rfb_op(ah
, rf_regs
, ee
->ee_db
[ee_mode
][obdb
],
823 AR5K_RF_DB_2GHZ
, true);
825 /* RF5111 always needs OB/DB for 5GHz, even if we use 2GHz */
826 } else if ((channel
->hw_value
& CHANNEL_5GHZ
) ||
827 (ah
->ah_radio
== AR5K_RF5111
)) {
829 /* For 11a, Turbo and XR we need to choose
830 * OB/DB based on frequency range */
831 ee_mode
= AR5K_EEPROM_MODE_11A
;
832 obdb
= channel
->center_freq
>= 5725 ? 3 :
833 (channel
->center_freq
>= 5500 ? 2 :
834 (channel
->center_freq
>= 5260 ? 1 :
835 (channel
->center_freq
> 4000 ? 0 : -1)));
840 ath5k_hw_rfb_op(ah
, rf_regs
, ee
->ee_ob
[ee_mode
][obdb
],
841 AR5K_RF_OB_5GHZ
, true);
843 ath5k_hw_rfb_op(ah
, rf_regs
, ee
->ee_db
[ee_mode
][obdb
],
844 AR5K_RF_DB_5GHZ
, true);
847 g_step
= &go
->go_step
[ah
->ah_gain
.g_step_idx
];
849 /* Set turbo mode (N/A on RF5413) */
850 if ((ah
->ah_bwmode
== AR5K_BWMODE_40MHZ
) &&
851 (ah
->ah_radio
!= AR5K_RF5413
))
852 ath5k_hw_rfb_op(ah
, rf_regs
, 1, AR5K_RF_TURBO
, false);
854 /* Bank Modifications (chip-specific) */
855 if (ah
->ah_radio
== AR5K_RF5111
) {
857 /* Set gain_F settings according to current step */
858 if (channel
->hw_value
& CHANNEL_OFDM
) {
860 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_FRAME_CTL
,
861 AR5K_PHY_FRAME_CTL_TX_CLIP
,
862 g_step
->gos_param
[0]);
864 ath5k_hw_rfb_op(ah
, rf_regs
, g_step
->gos_param
[1],
865 AR5K_RF_PWD_90
, true);
867 ath5k_hw_rfb_op(ah
, rf_regs
, g_step
->gos_param
[2],
868 AR5K_RF_PWD_84
, true);
870 ath5k_hw_rfb_op(ah
, rf_regs
, g_step
->gos_param
[3],
871 AR5K_RF_RFGAIN_SEL
, true);
873 /* We programmed gain_F parameters, switch back
875 ah
->ah_gain
.g_state
= AR5K_RFGAIN_ACTIVE
;
881 ath5k_hw_rfb_op(ah
, rf_regs
, !ee
->ee_xpd
[ee_mode
],
882 AR5K_RF_PWD_XPD
, true);
884 ath5k_hw_rfb_op(ah
, rf_regs
, ee
->ee_x_gain
[ee_mode
],
885 AR5K_RF_XPD_GAIN
, true);
887 ath5k_hw_rfb_op(ah
, rf_regs
, ee
->ee_i_gain
[ee_mode
],
888 AR5K_RF_GAIN_I
, true);
890 ath5k_hw_rfb_op(ah
, rf_regs
, ee
->ee_xpd
[ee_mode
],
891 AR5K_RF_PLO_SEL
, true);
893 /* Tweak power detectors for half/quarter rate support */
894 if (ah
->ah_bwmode
== AR5K_BWMODE_5MHZ
||
895 ah
->ah_bwmode
== AR5K_BWMODE_10MHZ
) {
898 ath5k_hw_rfb_op(ah
, rf_regs
, 0x1f,
899 AR5K_RF_WAIT_S
, true);
901 wait_i
= (ah
->ah_bwmode
== AR5K_BWMODE_5MHZ
) ?
904 ath5k_hw_rfb_op(ah
, rf_regs
, wait_i
,
905 AR5K_RF_WAIT_I
, true);
906 ath5k_hw_rfb_op(ah
, rf_regs
, 3,
907 AR5K_RF_MAX_TIME
, true);
912 if (ah
->ah_radio
== AR5K_RF5112
) {
914 /* Set gain_F settings according to current step */
915 if (channel
->hw_value
& CHANNEL_OFDM
) {
917 ath5k_hw_rfb_op(ah
, rf_regs
, g_step
->gos_param
[0],
918 AR5K_RF_MIXGAIN_OVR
, true);
920 ath5k_hw_rfb_op(ah
, rf_regs
, g_step
->gos_param
[1],
921 AR5K_RF_PWD_138
, true);
923 ath5k_hw_rfb_op(ah
, rf_regs
, g_step
->gos_param
[2],
924 AR5K_RF_PWD_137
, true);
926 ath5k_hw_rfb_op(ah
, rf_regs
, g_step
->gos_param
[3],
927 AR5K_RF_PWD_136
, true);
929 ath5k_hw_rfb_op(ah
, rf_regs
, g_step
->gos_param
[4],
930 AR5K_RF_PWD_132
, true);
932 ath5k_hw_rfb_op(ah
, rf_regs
, g_step
->gos_param
[5],
933 AR5K_RF_PWD_131
, true);
935 ath5k_hw_rfb_op(ah
, rf_regs
, g_step
->gos_param
[6],
936 AR5K_RF_PWD_130
, true);
938 /* We programmed gain_F parameters, switch back
940 ah
->ah_gain
.g_state
= AR5K_RFGAIN_ACTIVE
;
945 ath5k_hw_rfb_op(ah
, rf_regs
, ee
->ee_xpd
[ee_mode
],
946 AR5K_RF_XPD_SEL
, true);
948 if (ah
->ah_radio_5ghz_revision
< AR5K_SREV_RAD_5112A
) {
949 /* Rev. 1 supports only one xpd */
950 ath5k_hw_rfb_op(ah
, rf_regs
,
951 ee
->ee_x_gain
[ee_mode
],
952 AR5K_RF_XPD_GAIN
, true);
955 u8
*pdg_curve_to_idx
= ee
->ee_pdc_to_idx
[ee_mode
];
956 if (ee
->ee_pd_gains
[ee_mode
] > 1) {
957 ath5k_hw_rfb_op(ah
, rf_regs
,
959 AR5K_RF_PD_GAIN_LO
, true);
960 ath5k_hw_rfb_op(ah
, rf_regs
,
962 AR5K_RF_PD_GAIN_HI
, true);
964 ath5k_hw_rfb_op(ah
, rf_regs
,
966 AR5K_RF_PD_GAIN_LO
, true);
967 ath5k_hw_rfb_op(ah
, rf_regs
,
969 AR5K_RF_PD_GAIN_HI
, true);
972 /* Lower synth voltage on Rev 2 */
973 ath5k_hw_rfb_op(ah
, rf_regs
, 2,
974 AR5K_RF_HIGH_VC_CP
, true);
976 ath5k_hw_rfb_op(ah
, rf_regs
, 2,
977 AR5K_RF_MID_VC_CP
, true);
979 ath5k_hw_rfb_op(ah
, rf_regs
, 2,
980 AR5K_RF_LOW_VC_CP
, true);
982 ath5k_hw_rfb_op(ah
, rf_regs
, 2,
983 AR5K_RF_PUSH_UP
, true);
985 /* Decrease power consumption on 5213+ BaseBand */
986 if (ah
->ah_phy_revision
>= AR5K_SREV_PHY_5212A
) {
987 ath5k_hw_rfb_op(ah
, rf_regs
, 1,
988 AR5K_RF_PAD2GND
, true);
990 ath5k_hw_rfb_op(ah
, rf_regs
, 1,
991 AR5K_RF_XB2_LVL
, true);
993 ath5k_hw_rfb_op(ah
, rf_regs
, 1,
994 AR5K_RF_XB5_LVL
, true);
996 ath5k_hw_rfb_op(ah
, rf_regs
, 1,
997 AR5K_RF_PWD_167
, true);
999 ath5k_hw_rfb_op(ah
, rf_regs
, 1,
1000 AR5K_RF_PWD_166
, true);
1004 ath5k_hw_rfb_op(ah
, rf_regs
, ee
->ee_i_gain
[ee_mode
],
1005 AR5K_RF_GAIN_I
, true);
1007 /* Tweak power detector for half/quarter rates */
1008 if (ah
->ah_bwmode
== AR5K_BWMODE_5MHZ
||
1009 ah
->ah_bwmode
== AR5K_BWMODE_10MHZ
) {
1012 pd_delay
= (ah
->ah_bwmode
== AR5K_BWMODE_5MHZ
) ?
1015 ath5k_hw_rfb_op(ah
, rf_regs
, pd_delay
,
1016 AR5K_RF_PD_PERIOD_A
, true);
1017 ath5k_hw_rfb_op(ah
, rf_regs
, 0xf,
1018 AR5K_RF_PD_DELAY_A
, true);
1023 if (ah
->ah_radio
== AR5K_RF5413
&&
1024 channel
->hw_value
& CHANNEL_2GHZ
) {
1026 ath5k_hw_rfb_op(ah
, rf_regs
, 1, AR5K_RF_DERBY_CHAN_SEL_MODE
,
1029 /* Set optimum value for early revisions (on pci-e chips) */
1030 if (ah
->ah_mac_srev
>= AR5K_SREV_AR5424
&&
1031 ah
->ah_mac_srev
< AR5K_SREV_AR5413
)
1032 ath5k_hw_rfb_op(ah
, rf_regs
, ath5k_hw_bitswap(6, 3),
1033 AR5K_RF_PWD_ICLOBUF_2G
, true);
1037 /* Write RF banks on hw */
1038 for (i
= 0; i
< ah
->ah_rf_banks_size
; i
++) {
1040 ath5k_hw_reg_write(ah
, rfb
[i
], ini_rfb
[i
].rfb_ctrl_register
);
1047 /**************************\
1048 PHY/RF channel functions
1049 \**************************/
1052 * Conversion needed for RF5110
1054 static u32
ath5k_hw_rf5110_chan2athchan(struct ieee80211_channel
*channel
)
1059 * Convert IEEE channel/MHz to an internal channel value used
1060 * by the AR5210 chipset. This has not been verified with
1061 * newer chipsets like the AR5212A who have a completely
1062 * different RF/PHY part.
1064 athchan
= (ath5k_hw_bitswap(
1065 (ieee80211_frequency_to_channel(
1066 channel
->center_freq
) - 24) / 2, 5)
1067 << 1) | (1 << 6) | 0x1;
1072 * Set channel on RF5110
1074 static int ath5k_hw_rf5110_channel(struct ath5k_hw
*ah
,
1075 struct ieee80211_channel
*channel
)
1080 * Set the channel and wait
1082 data
= ath5k_hw_rf5110_chan2athchan(channel
);
1083 ath5k_hw_reg_write(ah
, data
, AR5K_RF_BUFFER
);
1084 ath5k_hw_reg_write(ah
, 0, AR5K_RF_BUFFER_CONTROL_0
);
1091 * Conversion needed for 5111
1093 static int ath5k_hw_rf5111_chan2athchan(unsigned int ieee
,
1094 struct ath5k_athchan_2ghz
*athchan
)
1098 /* Cast this value to catch negative channel numbers (>= -19) */
1099 channel
= (int)ieee
;
1102 * Map 2GHz IEEE channel to 5GHz Atheros channel
1104 if (channel
<= 13) {
1105 athchan
->a2_athchan
= 115 + channel
;
1106 athchan
->a2_flags
= 0x46;
1107 } else if (channel
== 14) {
1108 athchan
->a2_athchan
= 124;
1109 athchan
->a2_flags
= 0x44;
1110 } else if (channel
>= 15 && channel
<= 26) {
1111 athchan
->a2_athchan
= ((channel
- 14) * 4) + 132;
1112 athchan
->a2_flags
= 0x46;
1120 * Set channel on 5111
1122 static int ath5k_hw_rf5111_channel(struct ath5k_hw
*ah
,
1123 struct ieee80211_channel
*channel
)
1125 struct ath5k_athchan_2ghz ath5k_channel_2ghz
;
1126 unsigned int ath5k_channel
=
1127 ieee80211_frequency_to_channel(channel
->center_freq
);
1128 u32 data0
, data1
, clock
;
1132 * Set the channel on the RF5111 radio
1136 if (channel
->hw_value
& CHANNEL_2GHZ
) {
1137 /* Map 2GHz channel to 5GHz Atheros channel ID */
1138 ret
= ath5k_hw_rf5111_chan2athchan(
1139 ieee80211_frequency_to_channel(channel
->center_freq
),
1140 &ath5k_channel_2ghz
);
1144 ath5k_channel
= ath5k_channel_2ghz
.a2_athchan
;
1145 data0
= ((ath5k_hw_bitswap(ath5k_channel_2ghz
.a2_flags
, 8) & 0xff)
1149 if (ath5k_channel
< 145 || !(ath5k_channel
& 1)) {
1151 data1
= ((ath5k_hw_bitswap(ath5k_channel
- 24, 8) & 0xff) << 2) |
1152 (clock
<< 1) | (1 << 10) | 1;
1155 data1
= ((ath5k_hw_bitswap((ath5k_channel
- 24) / 2, 8) & 0xff)
1156 << 2) | (clock
<< 1) | (1 << 10) | 1;
1159 ath5k_hw_reg_write(ah
, (data1
& 0xff) | ((data0
& 0xff) << 8),
1161 ath5k_hw_reg_write(ah
, ((data1
>> 8) & 0xff) | (data0
& 0xff00),
1162 AR5K_RF_BUFFER_CONTROL_3
);
1168 * Set channel on 5112 and newer
1170 static int ath5k_hw_rf5112_channel(struct ath5k_hw
*ah
,
1171 struct ieee80211_channel
*channel
)
1173 u32 data
, data0
, data1
, data2
;
1176 data
= data0
= data1
= data2
= 0;
1177 c
= channel
->center_freq
;
1180 if (!((c
- 2224) % 5)) {
1181 data0
= ((2 * (c
- 704)) - 3040) / 10;
1183 } else if (!((c
- 2192) % 5)) {
1184 data0
= ((2 * (c
- 672)) - 3040) / 10;
1189 data0
= ath5k_hw_bitswap((data0
<< 2) & 0xff, 8);
1190 } else if ((c
% 5) != 2 || c
> 5435) {
1191 if (!(c
% 20) && c
>= 5120) {
1192 data0
= ath5k_hw_bitswap(((c
- 4800) / 20 << 2), 8);
1193 data2
= ath5k_hw_bitswap(3, 2);
1194 } else if (!(c
% 10)) {
1195 data0
= ath5k_hw_bitswap(((c
- 4800) / 10 << 1), 8);
1196 data2
= ath5k_hw_bitswap(2, 2);
1197 } else if (!(c
% 5)) {
1198 data0
= ath5k_hw_bitswap((c
- 4800) / 5, 8);
1199 data2
= ath5k_hw_bitswap(1, 2);
1203 data0
= ath5k_hw_bitswap((10 * (c
- 2 - 4800)) / 25 + 1, 8);
1204 data2
= ath5k_hw_bitswap(0, 2);
1207 data
= (data0
<< 4) | (data1
<< 1) | (data2
<< 2) | 0x1001;
1209 ath5k_hw_reg_write(ah
, data
& 0xff, AR5K_RF_BUFFER
);
1210 ath5k_hw_reg_write(ah
, (data
>> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5
);
1216 * Set the channel on the RF2425
1218 static int ath5k_hw_rf2425_channel(struct ath5k_hw
*ah
,
1219 struct ieee80211_channel
*channel
)
1221 u32 data
, data0
, data2
;
1224 data
= data0
= data2
= 0;
1225 c
= channel
->center_freq
;
1228 data0
= ath5k_hw_bitswap((c
- 2272), 8);
1231 } else if ((c
% 5) != 2 || c
> 5435) {
1232 if (!(c
% 20) && c
< 5120)
1233 data0
= ath5k_hw_bitswap(((c
- 4800) / 20 << 2), 8);
1235 data0
= ath5k_hw_bitswap(((c
- 4800) / 10 << 1), 8);
1237 data0
= ath5k_hw_bitswap((c
- 4800) / 5, 8);
1240 data2
= ath5k_hw_bitswap(1, 2);
1242 data0
= ath5k_hw_bitswap((10 * (c
- 2 - 4800)) / 25 + 1, 8);
1243 data2
= ath5k_hw_bitswap(0, 2);
1246 data
= (data0
<< 4) | data2
<< 2 | 0x1001;
1248 ath5k_hw_reg_write(ah
, data
& 0xff, AR5K_RF_BUFFER
);
1249 ath5k_hw_reg_write(ah
, (data
>> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5
);
1255 * Set a channel on the radio chip
1257 static int ath5k_hw_channel(struct ath5k_hw
*ah
,
1258 struct ieee80211_channel
*channel
)
1262 * Check bounds supported by the PHY (we don't care about regulatory
1263 * restrictions at this point). Note: hw_value already has the band
1264 * (CHANNEL_2GHZ, or CHANNEL_5GHZ) so we inform ath5k_channel_ok()
1265 * of the band by that */
1266 if (!ath5k_channel_ok(ah
, channel
->center_freq
, channel
->hw_value
)) {
1267 ATH5K_ERR(ah
->ah_sc
,
1268 "channel frequency (%u MHz) out of supported "
1270 channel
->center_freq
);
1275 * Set the channel and wait
1277 switch (ah
->ah_radio
) {
1279 ret
= ath5k_hw_rf5110_channel(ah
, channel
);
1282 ret
= ath5k_hw_rf5111_channel(ah
, channel
);
1286 ret
= ath5k_hw_rf2425_channel(ah
, channel
);
1289 ret
= ath5k_hw_rf5112_channel(ah
, channel
);
1296 /* Set JAPAN setting for channel 14 */
1297 if (channel
->center_freq
== 2484) {
1298 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_CCKTXCTL
,
1299 AR5K_PHY_CCKTXCTL_JAPAN
);
1301 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_CCKTXCTL
,
1302 AR5K_PHY_CCKTXCTL_WORLD
);
1305 ah
->ah_current_channel
= channel
;
1314 static s32
ath5k_hw_read_measured_noise_floor(struct ath5k_hw
*ah
)
1318 val
= ath5k_hw_reg_read(ah
, AR5K_PHY_NF
);
1319 return sign_extend32(AR5K_REG_MS(val
, AR5K_PHY_NF_MINCCA_PWR
), 8);
1322 void ath5k_hw_init_nfcal_hist(struct ath5k_hw
*ah
)
1326 ah
->ah_nfcal_hist
.index
= 0;
1327 for (i
= 0; i
< ATH5K_NF_CAL_HIST_MAX
; i
++)
1328 ah
->ah_nfcal_hist
.nfval
[i
] = AR5K_TUNE_CCA_MAX_GOOD_VALUE
;
1331 static void ath5k_hw_update_nfcal_hist(struct ath5k_hw
*ah
, s16 noise_floor
)
1333 struct ath5k_nfcal_hist
*hist
= &ah
->ah_nfcal_hist
;
1334 hist
->index
= (hist
->index
+ 1) & (ATH5K_NF_CAL_HIST_MAX
- 1);
1335 hist
->nfval
[hist
->index
] = noise_floor
;
1338 static s16
ath5k_hw_get_median_noise_floor(struct ath5k_hw
*ah
)
1340 s16 sort
[ATH5K_NF_CAL_HIST_MAX
];
1344 memcpy(sort
, ah
->ah_nfcal_hist
.nfval
, sizeof(sort
));
1345 for (i
= 0; i
< ATH5K_NF_CAL_HIST_MAX
- 1; i
++) {
1346 for (j
= 1; j
< ATH5K_NF_CAL_HIST_MAX
- i
; j
++) {
1347 if (sort
[j
] > sort
[j
- 1]) {
1349 sort
[j
] = sort
[j
- 1];
1354 for (i
= 0; i
< ATH5K_NF_CAL_HIST_MAX
; i
++) {
1355 ATH5K_DBG(ah
->ah_sc
, ATH5K_DEBUG_CALIBRATE
,
1356 "cal %d:%d\n", i
, sort
[i
]);
1358 return sort
[(ATH5K_NF_CAL_HIST_MAX
- 1) / 2];
1362 * When we tell the hardware to perform a noise floor calibration
1363 * by setting the AR5K_PHY_AGCCTL_NF bit, it will periodically
1364 * sample-and-hold the minimum noise level seen at the antennas.
1365 * This value is then stored in a ring buffer of recently measured
1366 * noise floor values so we have a moving window of the last few
1369 * The median of the values in the history is then loaded into the
1370 * hardware for its own use for RSSI and CCA measurements.
1372 void ath5k_hw_update_noise_floor(struct ath5k_hw
*ah
)
1374 struct ath5k_eeprom_info
*ee
= &ah
->ah_capabilities
.cap_eeprom
;
1379 /* keep last value if calibration hasn't completed */
1380 if (ath5k_hw_reg_read(ah
, AR5K_PHY_AGCCTL
) & AR5K_PHY_AGCCTL_NF
) {
1381 ATH5K_DBG(ah
->ah_sc
, ATH5K_DEBUG_CALIBRATE
,
1382 "NF did not complete in calibration window\n");
1387 ee_mode
= ath5k_eeprom_mode_from_channel(ah
->ah_current_channel
);
1389 /* completed NF calibration, test threshold */
1390 nf
= ath5k_hw_read_measured_noise_floor(ah
);
1391 threshold
= ee
->ee_noise_floor_thr
[ee_mode
];
1393 if (nf
> threshold
) {
1394 ATH5K_DBG(ah
->ah_sc
, ATH5K_DEBUG_CALIBRATE
,
1395 "noise floor failure detected; "
1396 "read %d, threshold %d\n",
1399 nf
= AR5K_TUNE_CCA_MAX_GOOD_VALUE
;
1402 ath5k_hw_update_nfcal_hist(ah
, nf
);
1403 nf
= ath5k_hw_get_median_noise_floor(ah
);
1405 /* load noise floor (in .5 dBm) so the hardware will use it */
1406 val
= ath5k_hw_reg_read(ah
, AR5K_PHY_NF
) & ~AR5K_PHY_NF_M
;
1407 val
|= (nf
* 2) & AR5K_PHY_NF_M
;
1408 ath5k_hw_reg_write(ah
, val
, AR5K_PHY_NF
);
1410 AR5K_REG_MASKED_BITS(ah
, AR5K_PHY_AGCCTL
, AR5K_PHY_AGCCTL_NF
,
1411 ~(AR5K_PHY_AGCCTL_NF_EN
| AR5K_PHY_AGCCTL_NF_NOUPDATE
));
1413 ath5k_hw_register_timeout(ah
, AR5K_PHY_AGCCTL
, AR5K_PHY_AGCCTL_NF
,
1417 * Load a high max CCA Power value (-50 dBm in .5 dBm units)
1418 * so that we're not capped by the median we just loaded.
1419 * This will be used as the initial value for the next noise
1420 * floor calibration.
1422 val
= (val
& ~AR5K_PHY_NF_M
) | ((-50 * 2) & AR5K_PHY_NF_M
);
1423 ath5k_hw_reg_write(ah
, val
, AR5K_PHY_NF
);
1424 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_AGCCTL
,
1425 AR5K_PHY_AGCCTL_NF_EN
|
1426 AR5K_PHY_AGCCTL_NF_NOUPDATE
|
1427 AR5K_PHY_AGCCTL_NF
);
1429 ah
->ah_noise_floor
= nf
;
1431 ATH5K_DBG(ah
->ah_sc
, ATH5K_DEBUG_CALIBRATE
,
1432 "noise floor calibrated: %d\n", nf
);
1436 * Perform a PHY calibration on RF5110
1437 * -Fix BPSK/QAM Constellation (I/Q correction)
1439 static int ath5k_hw_rf5110_calibrate(struct ath5k_hw
*ah
,
1440 struct ieee80211_channel
*channel
)
1442 u32 phy_sig
, phy_agc
, phy_sat
, beacon
;
1446 * Disable beacons and RX/TX queues, wait
1448 AR5K_REG_ENABLE_BITS(ah
, AR5K_DIAG_SW_5210
,
1449 AR5K_DIAG_SW_DIS_TX_5210
| AR5K_DIAG_SW_DIS_RX_5210
);
1450 beacon
= ath5k_hw_reg_read(ah
, AR5K_BEACON_5210
);
1451 ath5k_hw_reg_write(ah
, beacon
& ~AR5K_BEACON_ENABLE
, AR5K_BEACON_5210
);
1456 * Set the channel (with AGC turned off)
1458 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_AGC
, AR5K_PHY_AGC_DISABLE
);
1460 ret
= ath5k_hw_channel(ah
, channel
);
1463 * Activate PHY and wait
1465 ath5k_hw_reg_write(ah
, AR5K_PHY_ACT_ENABLE
, AR5K_PHY_ACT
);
1468 AR5K_REG_DISABLE_BITS(ah
, AR5K_PHY_AGC
, AR5K_PHY_AGC_DISABLE
);
1474 * Calibrate the radio chip
1477 /* Remember normal state */
1478 phy_sig
= ath5k_hw_reg_read(ah
, AR5K_PHY_SIG
);
1479 phy_agc
= ath5k_hw_reg_read(ah
, AR5K_PHY_AGCCOARSE
);
1480 phy_sat
= ath5k_hw_reg_read(ah
, AR5K_PHY_ADCSAT
);
1482 /* Update radio registers */
1483 ath5k_hw_reg_write(ah
, (phy_sig
& ~(AR5K_PHY_SIG_FIRPWR
)) |
1484 AR5K_REG_SM(-1, AR5K_PHY_SIG_FIRPWR
), AR5K_PHY_SIG
);
1486 ath5k_hw_reg_write(ah
, (phy_agc
& ~(AR5K_PHY_AGCCOARSE_HI
|
1487 AR5K_PHY_AGCCOARSE_LO
)) |
1488 AR5K_REG_SM(-1, AR5K_PHY_AGCCOARSE_HI
) |
1489 AR5K_REG_SM(-127, AR5K_PHY_AGCCOARSE_LO
), AR5K_PHY_AGCCOARSE
);
1491 ath5k_hw_reg_write(ah
, (phy_sat
& ~(AR5K_PHY_ADCSAT_ICNT
|
1492 AR5K_PHY_ADCSAT_THR
)) |
1493 AR5K_REG_SM(2, AR5K_PHY_ADCSAT_ICNT
) |
1494 AR5K_REG_SM(12, AR5K_PHY_ADCSAT_THR
), AR5K_PHY_ADCSAT
);
1498 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_AGC
, AR5K_PHY_AGC_DISABLE
);
1500 ath5k_hw_reg_write(ah
, AR5K_PHY_RFSTG_DISABLE
, AR5K_PHY_RFSTG
);
1501 AR5K_REG_DISABLE_BITS(ah
, AR5K_PHY_AGC
, AR5K_PHY_AGC_DISABLE
);
1506 * Enable calibration and wait until completion
1508 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_AGCCTL
, AR5K_PHY_AGCCTL_CAL
);
1510 ret
= ath5k_hw_register_timeout(ah
, AR5K_PHY_AGCCTL
,
1511 AR5K_PHY_AGCCTL_CAL
, 0, false);
1513 /* Reset to normal state */
1514 ath5k_hw_reg_write(ah
, phy_sig
, AR5K_PHY_SIG
);
1515 ath5k_hw_reg_write(ah
, phy_agc
, AR5K_PHY_AGCCOARSE
);
1516 ath5k_hw_reg_write(ah
, phy_sat
, AR5K_PHY_ADCSAT
);
1519 ATH5K_ERR(ah
->ah_sc
, "calibration timeout (%uMHz)\n",
1520 channel
->center_freq
);
1525 * Re-enable RX/TX and beacons
1527 AR5K_REG_DISABLE_BITS(ah
, AR5K_DIAG_SW_5210
,
1528 AR5K_DIAG_SW_DIS_TX_5210
| AR5K_DIAG_SW_DIS_RX_5210
);
1529 ath5k_hw_reg_write(ah
, beacon
, AR5K_BEACON_5210
);
1535 * Perform I/Q calibration on RF5111/5112 and newer chips
1538 ath5k_hw_rf511x_iq_calibrate(struct ath5k_hw
*ah
)
1541 s32 iq_corr
, i_coff
, i_coffd
, q_coff
, q_coffd
;
1544 if (!ah
->ah_calibration
||
1545 ath5k_hw_reg_read(ah
, AR5K_PHY_IQ
) & AR5K_PHY_IQ_RUN
)
1548 /* Calibration has finished, get the results and re-run */
1549 /* work around empty results which can apparently happen on 5212 */
1550 for (i
= 0; i
<= 10; i
++) {
1551 iq_corr
= ath5k_hw_reg_read(ah
, AR5K_PHY_IQRES_CAL_CORR
);
1552 i_pwr
= ath5k_hw_reg_read(ah
, AR5K_PHY_IQRES_CAL_PWR_I
);
1553 q_pwr
= ath5k_hw_reg_read(ah
, AR5K_PHY_IQRES_CAL_PWR_Q
);
1554 ATH5K_DBG_UNLIMIT(ah
->ah_sc
, ATH5K_DEBUG_CALIBRATE
,
1555 "iq_corr:%x i_pwr:%x q_pwr:%x", iq_corr
, i_pwr
, q_pwr
);
1560 i_coffd
= ((i_pwr
>> 1) + (q_pwr
>> 1)) >> 7;
1562 if (ah
->ah_version
== AR5K_AR5211
)
1563 q_coffd
= q_pwr
>> 6;
1565 q_coffd
= q_pwr
>> 7;
1567 /* protect against divide by 0 and loss of sign bits */
1568 if (i_coffd
== 0 || q_coffd
< 2)
1571 i_coff
= (-iq_corr
) / i_coffd
;
1572 i_coff
= clamp(i_coff
, -32, 31); /* signed 6 bit */
1574 if (ah
->ah_version
== AR5K_AR5211
)
1575 q_coff
= (i_pwr
/ q_coffd
) - 64;
1577 q_coff
= (i_pwr
/ q_coffd
) - 128;
1578 q_coff
= clamp(q_coff
, -16, 15); /* signed 5 bit */
1580 ATH5K_DBG_UNLIMIT(ah
->ah_sc
, ATH5K_DEBUG_CALIBRATE
,
1581 "new I:%d Q:%d (i_coffd:%x q_coffd:%x)",
1582 i_coff
, q_coff
, i_coffd
, q_coffd
);
1584 /* Commit new I/Q values (set enable bit last to match HAL sources) */
1585 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_IQ
, AR5K_PHY_IQ_CORR_Q_I_COFF
, i_coff
);
1586 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_IQ
, AR5K_PHY_IQ_CORR_Q_Q_COFF
, q_coff
);
1587 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_IQ
, AR5K_PHY_IQ_CORR_ENABLE
);
1589 /* Re-enable calibration -if we don't we'll commit
1590 * the same values again and again */
1591 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_IQ
,
1592 AR5K_PHY_IQ_CAL_NUM_LOG_MAX
, 15);
1593 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_IQ
, AR5K_PHY_IQ_RUN
);
1599 * Perform a PHY calibration
1601 int ath5k_hw_phy_calibrate(struct ath5k_hw
*ah
,
1602 struct ieee80211_channel
*channel
)
1606 if (ah
->ah_radio
== AR5K_RF5110
)
1607 ret
= ath5k_hw_rf5110_calibrate(ah
, channel
);
1609 ret
= ath5k_hw_rf511x_iq_calibrate(ah
);
1610 ath5k_hw_request_rfgain_probe(ah
);
1617 /***************************\
1618 * Spur mitigation functions *
1619 \***************************/
1622 ath5k_hw_set_spur_mitigation_filter(struct ath5k_hw
*ah
,
1623 struct ieee80211_channel
*channel
)
1625 struct ath5k_eeprom_info
*ee
= &ah
->ah_capabilities
.cap_eeprom
;
1626 u32 mag_mask
[4] = {0, 0, 0, 0};
1627 u32 pilot_mask
[2] = {0, 0};
1628 /* Note: fbin values are scaled up by 2 */
1629 u16 spur_chan_fbin
, chan_fbin
, symbol_width
, spur_detection_window
;
1630 s32 spur_delta_phase
, spur_freq_sigma_delta
;
1631 s32 spur_offset
, num_symbols_x16
;
1632 u8 num_symbol_offsets
, i
, freq_band
;
1634 /* Convert current frequency to fbin value (the same way channels
1635 * are stored on EEPROM, check out ath5k_eeprom_bin2freq) and scale
1636 * up by 2 so we can compare it later */
1637 if (channel
->hw_value
& CHANNEL_2GHZ
) {
1638 chan_fbin
= (channel
->center_freq
- 2300) * 10;
1639 freq_band
= AR5K_EEPROM_BAND_2GHZ
;
1641 chan_fbin
= (channel
->center_freq
- 4900) * 10;
1642 freq_band
= AR5K_EEPROM_BAND_5GHZ
;
1645 /* Check if any spur_chan_fbin from EEPROM is
1646 * within our current channel's spur detection range */
1647 spur_chan_fbin
= AR5K_EEPROM_NO_SPUR
;
1648 spur_detection_window
= AR5K_SPUR_CHAN_WIDTH
;
1649 /* XXX: Half/Quarter channels ?*/
1650 if (ah
->ah_bwmode
== AR5K_BWMODE_40MHZ
)
1651 spur_detection_window
*= 2;
1653 for (i
= 0; i
< AR5K_EEPROM_N_SPUR_CHANS
; i
++) {
1654 spur_chan_fbin
= ee
->ee_spur_chans
[i
][freq_band
];
1656 /* Note: mask cleans AR5K_EEPROM_NO_SPUR flag
1657 * so it's zero if we got nothing from EEPROM */
1658 if (spur_chan_fbin
== AR5K_EEPROM_NO_SPUR
) {
1659 spur_chan_fbin
&= AR5K_EEPROM_SPUR_CHAN_MASK
;
1663 if ((chan_fbin
- spur_detection_window
<=
1664 (spur_chan_fbin
& AR5K_EEPROM_SPUR_CHAN_MASK
)) &&
1665 (chan_fbin
+ spur_detection_window
>=
1666 (spur_chan_fbin
& AR5K_EEPROM_SPUR_CHAN_MASK
))) {
1667 spur_chan_fbin
&= AR5K_EEPROM_SPUR_CHAN_MASK
;
1672 /* We need to enable spur filter for this channel */
1673 if (spur_chan_fbin
) {
1674 spur_offset
= spur_chan_fbin
- chan_fbin
;
1677 * spur_freq_sigma_delta -> spur_offset / sample_freq << 21
1678 * spur_delta_phase -> spur_offset / chip_freq << 11
1679 * Note: Both values have 100Hz resolution
1681 switch (ah
->ah_bwmode
) {
1682 case AR5K_BWMODE_40MHZ
:
1683 /* Both sample_freq and chip_freq are 80MHz */
1684 spur_delta_phase
= (spur_offset
<< 16) / 25;
1685 spur_freq_sigma_delta
= (spur_delta_phase
>> 10);
1686 symbol_width
= AR5K_SPUR_SYMBOL_WIDTH_BASE_100Hz
* 2;
1688 case AR5K_BWMODE_10MHZ
:
1689 /* Both sample_freq and chip_freq are 20MHz (?) */
1690 spur_delta_phase
= (spur_offset
<< 18) / 25;
1691 spur_freq_sigma_delta
= (spur_delta_phase
>> 10);
1692 symbol_width
= AR5K_SPUR_SYMBOL_WIDTH_BASE_100Hz
/ 2;
1693 case AR5K_BWMODE_5MHZ
:
1694 /* Both sample_freq and chip_freq are 10MHz (?) */
1695 spur_delta_phase
= (spur_offset
<< 19) / 25;
1696 spur_freq_sigma_delta
= (spur_delta_phase
>> 10);
1697 symbol_width
= AR5K_SPUR_SYMBOL_WIDTH_BASE_100Hz
/ 4;
1699 if (channel
->hw_value
== CHANNEL_A
) {
1700 /* Both sample_freq and chip_freq are 40MHz */
1701 spur_delta_phase
= (spur_offset
<< 17) / 25;
1702 spur_freq_sigma_delta
=
1703 (spur_delta_phase
>> 10);
1705 AR5K_SPUR_SYMBOL_WIDTH_BASE_100Hz
;
1707 /* sample_freq -> 40MHz chip_freq -> 44MHz
1708 * (for b compatibility) */
1709 spur_delta_phase
= (spur_offset
<< 17) / 25;
1710 spur_freq_sigma_delta
=
1711 (spur_offset
<< 8) / 55;
1713 AR5K_SPUR_SYMBOL_WIDTH_BASE_100Hz
;
1718 /* Calculate pilot and magnitude masks */
1720 /* Scale up spur_offset by 1000 to switch to 100HZ resolution
1721 * and divide by symbol_width to find how many symbols we have
1722 * Note: number of symbols is scaled up by 16 */
1723 num_symbols_x16
= ((spur_offset
* 1000) << 4) / symbol_width
;
1725 /* Spur is on a symbol if num_symbols_x16 % 16 is zero */
1726 if (!(num_symbols_x16
& 0xF))
1728 num_symbol_offsets
= 3;
1731 num_symbol_offsets
= 4;
1733 for (i
= 0; i
< num_symbol_offsets
; i
++) {
1735 /* Calculate pilot mask */
1737 (num_symbols_x16
/ 16) + i
+ 25;
1739 /* Pilot magnitude mask seems to be a way to
1740 * declare the boundaries for our detection
1741 * window or something, it's 2 for the middle
1742 * value(s) where the symbol is expected to be
1743 * and 1 on the boundary values */
1745 (i
== 0 || i
== (num_symbol_offsets
- 1))
1748 if (curr_sym_off
>= 0 && curr_sym_off
<= 32) {
1749 if (curr_sym_off
<= 25)
1750 pilot_mask
[0] |= 1 << curr_sym_off
;
1751 else if (curr_sym_off
>= 27)
1752 pilot_mask
[0] |= 1 << (curr_sym_off
- 1);
1753 } else if (curr_sym_off
>= 33 && curr_sym_off
<= 52)
1754 pilot_mask
[1] |= 1 << (curr_sym_off
- 33);
1756 /* Calculate magnitude mask (for viterbi decoder) */
1757 if (curr_sym_off
>= -1 && curr_sym_off
<= 14)
1759 plt_mag_map
<< (curr_sym_off
+ 1) * 2;
1760 else if (curr_sym_off
>= 15 && curr_sym_off
<= 30)
1762 plt_mag_map
<< (curr_sym_off
- 15) * 2;
1763 else if (curr_sym_off
>= 31 && curr_sym_off
<= 46)
1765 plt_mag_map
<< (curr_sym_off
- 31) * 2;
1766 else if (curr_sym_off
>= 47 && curr_sym_off
<= 53)
1768 plt_mag_map
<< (curr_sym_off
- 47) * 2;
1772 /* Write settings on hw to enable spur filter */
1773 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_BIN_MASK_CTL
,
1774 AR5K_PHY_BIN_MASK_CTL_RATE
, 0xff);
1775 /* XXX: Self correlator also ? */
1776 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_IQ
,
1777 AR5K_PHY_IQ_PILOT_MASK_EN
|
1778 AR5K_PHY_IQ_CHAN_MASK_EN
|
1779 AR5K_PHY_IQ_SPUR_FILT_EN
);
1781 /* Set delta phase and freq sigma delta */
1782 ath5k_hw_reg_write(ah
,
1783 AR5K_REG_SM(spur_delta_phase
,
1784 AR5K_PHY_TIMING_11_SPUR_DELTA_PHASE
) |
1785 AR5K_REG_SM(spur_freq_sigma_delta
,
1786 AR5K_PHY_TIMING_11_SPUR_FREQ_SD
) |
1787 AR5K_PHY_TIMING_11_USE_SPUR_IN_AGC
,
1788 AR5K_PHY_TIMING_11
);
1790 /* Write pilot masks */
1791 ath5k_hw_reg_write(ah
, pilot_mask
[0], AR5K_PHY_TIMING_7
);
1792 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_TIMING_8
,
1793 AR5K_PHY_TIMING_8_PILOT_MASK_2
,
1796 ath5k_hw_reg_write(ah
, pilot_mask
[0], AR5K_PHY_TIMING_9
);
1797 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_TIMING_10
,
1798 AR5K_PHY_TIMING_10_PILOT_MASK_2
,
1801 /* Write magnitude masks */
1802 ath5k_hw_reg_write(ah
, mag_mask
[0], AR5K_PHY_BIN_MASK_1
);
1803 ath5k_hw_reg_write(ah
, mag_mask
[1], AR5K_PHY_BIN_MASK_2
);
1804 ath5k_hw_reg_write(ah
, mag_mask
[2], AR5K_PHY_BIN_MASK_3
);
1805 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_BIN_MASK_CTL
,
1806 AR5K_PHY_BIN_MASK_CTL_MASK_4
,
1809 ath5k_hw_reg_write(ah
, mag_mask
[0], AR5K_PHY_BIN_MASK2_1
);
1810 ath5k_hw_reg_write(ah
, mag_mask
[1], AR5K_PHY_BIN_MASK2_2
);
1811 ath5k_hw_reg_write(ah
, mag_mask
[2], AR5K_PHY_BIN_MASK2_3
);
1812 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_BIN_MASK2_4
,
1813 AR5K_PHY_BIN_MASK2_4_MASK_4
,
1816 } else if (ath5k_hw_reg_read(ah
, AR5K_PHY_IQ
) &
1817 AR5K_PHY_IQ_SPUR_FILT_EN
) {
1818 /* Clean up spur mitigation settings and disable filter */
1819 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_BIN_MASK_CTL
,
1820 AR5K_PHY_BIN_MASK_CTL_RATE
, 0);
1821 AR5K_REG_DISABLE_BITS(ah
, AR5K_PHY_IQ
,
1822 AR5K_PHY_IQ_PILOT_MASK_EN
|
1823 AR5K_PHY_IQ_CHAN_MASK_EN
|
1824 AR5K_PHY_IQ_SPUR_FILT_EN
);
1825 ath5k_hw_reg_write(ah
, 0, AR5K_PHY_TIMING_11
);
1827 /* Clear pilot masks */
1828 ath5k_hw_reg_write(ah
, 0, AR5K_PHY_TIMING_7
);
1829 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_TIMING_8
,
1830 AR5K_PHY_TIMING_8_PILOT_MASK_2
,
1833 ath5k_hw_reg_write(ah
, 0, AR5K_PHY_TIMING_9
);
1834 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_TIMING_10
,
1835 AR5K_PHY_TIMING_10_PILOT_MASK_2
,
1838 /* Clear magnitude masks */
1839 ath5k_hw_reg_write(ah
, 0, AR5K_PHY_BIN_MASK_1
);
1840 ath5k_hw_reg_write(ah
, 0, AR5K_PHY_BIN_MASK_2
);
1841 ath5k_hw_reg_write(ah
, 0, AR5K_PHY_BIN_MASK_3
);
1842 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_BIN_MASK_CTL
,
1843 AR5K_PHY_BIN_MASK_CTL_MASK_4
,
1846 ath5k_hw_reg_write(ah
, 0, AR5K_PHY_BIN_MASK2_1
);
1847 ath5k_hw_reg_write(ah
, 0, AR5K_PHY_BIN_MASK2_2
);
1848 ath5k_hw_reg_write(ah
, 0, AR5K_PHY_BIN_MASK2_3
);
1849 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_BIN_MASK2_4
,
1850 AR5K_PHY_BIN_MASK2_4_MASK_4
,
1860 static void /*TODO:Boundary check*/
1861 ath5k_hw_set_def_antenna(struct ath5k_hw
*ah
, u8 ant
)
1863 if (ah
->ah_version
!= AR5K_AR5210
)
1864 ath5k_hw_reg_write(ah
, ant
& 0x7, AR5K_DEFAULT_ANTENNA
);
1868 * Enable/disable fast rx antenna diversity
1871 ath5k_hw_set_fast_div(struct ath5k_hw
*ah
, u8 ee_mode
, bool enable
)
1874 case AR5K_EEPROM_MODE_11G
:
1875 /* XXX: This is set to
1876 * disabled on initvals !!! */
1877 case AR5K_EEPROM_MODE_11A
:
1879 AR5K_REG_DISABLE_BITS(ah
, AR5K_PHY_AGCCTL
,
1880 AR5K_PHY_AGCCTL_OFDM_DIV_DIS
);
1882 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_AGCCTL
,
1883 AR5K_PHY_AGCCTL_OFDM_DIV_DIS
);
1885 case AR5K_EEPROM_MODE_11B
:
1886 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_AGCCTL
,
1887 AR5K_PHY_AGCCTL_OFDM_DIV_DIS
);
1894 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_RESTART
,
1895 AR5K_PHY_RESTART_DIV_GC
, 4);
1897 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_FAST_ANT_DIV
,
1898 AR5K_PHY_FAST_ANT_DIV_EN
);
1900 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_RESTART
,
1901 AR5K_PHY_RESTART_DIV_GC
, 0);
1903 AR5K_REG_DISABLE_BITS(ah
, AR5K_PHY_FAST_ANT_DIV
,
1904 AR5K_PHY_FAST_ANT_DIV_EN
);
1909 ath5k_hw_set_antenna_switch(struct ath5k_hw
*ah
, u8 ee_mode
)
1914 * In case a fixed antenna was set as default
1915 * use the same switch table twice.
1917 if (ah
->ah_ant_mode
== AR5K_ANTMODE_FIXED_A
)
1918 ant0
= ant1
= AR5K_ANT_SWTABLE_A
;
1919 else if (ah
->ah_ant_mode
== AR5K_ANTMODE_FIXED_B
)
1920 ant0
= ant1
= AR5K_ANT_SWTABLE_B
;
1922 ant0
= AR5K_ANT_SWTABLE_A
;
1923 ant1
= AR5K_ANT_SWTABLE_B
;
1926 /* Set antenna idle switch table */
1927 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_ANT_CTL
,
1928 AR5K_PHY_ANT_CTL_SWTABLE_IDLE
,
1929 (ah
->ah_ant_ctl
[ee_mode
][AR5K_ANT_CTL
] |
1930 AR5K_PHY_ANT_CTL_TXRX_EN
));
1932 /* Set antenna switch tables */
1933 ath5k_hw_reg_write(ah
, ah
->ah_ant_ctl
[ee_mode
][ant0
],
1934 AR5K_PHY_ANT_SWITCH_TABLE_0
);
1935 ath5k_hw_reg_write(ah
, ah
->ah_ant_ctl
[ee_mode
][ant1
],
1936 AR5K_PHY_ANT_SWITCH_TABLE_1
);
1940 * Set antenna operating mode
1943 ath5k_hw_set_antenna_mode(struct ath5k_hw
*ah
, u8 ant_mode
)
1945 struct ieee80211_channel
*channel
= ah
->ah_current_channel
;
1946 bool use_def_for_tx
, update_def_on_tx
, use_def_for_rts
, fast_div
;
1947 bool use_def_for_sg
;
1952 /* if channel is not initialized yet we can't set the antennas
1953 * so just store the mode. it will be set on the next reset */
1954 if (channel
== NULL
) {
1955 ah
->ah_ant_mode
= ant_mode
;
1959 def_ant
= ah
->ah_def_ant
;
1961 ee_mode
= ath5k_eeprom_mode_from_channel(channel
);
1963 ATH5K_ERR(ah
->ah_sc
,
1964 "invalid channel: %d\n", channel
->center_freq
);
1969 case AR5K_ANTMODE_DEFAULT
:
1971 use_def_for_tx
= false;
1972 update_def_on_tx
= false;
1973 use_def_for_rts
= false;
1974 use_def_for_sg
= false;
1977 case AR5K_ANTMODE_FIXED_A
:
1980 use_def_for_tx
= true;
1981 update_def_on_tx
= false;
1982 use_def_for_rts
= true;
1983 use_def_for_sg
= true;
1986 case AR5K_ANTMODE_FIXED_B
:
1989 use_def_for_tx
= true;
1990 update_def_on_tx
= false;
1991 use_def_for_rts
= true;
1992 use_def_for_sg
= true;
1995 case AR5K_ANTMODE_SINGLE_AP
:
1996 def_ant
= 1; /* updated on tx */
1998 use_def_for_tx
= true;
1999 update_def_on_tx
= true;
2000 use_def_for_rts
= true;
2001 use_def_for_sg
= true;
2004 case AR5K_ANTMODE_SECTOR_AP
:
2005 tx_ant
= 1; /* variable */
2006 use_def_for_tx
= false;
2007 update_def_on_tx
= false;
2008 use_def_for_rts
= true;
2009 use_def_for_sg
= false;
2012 case AR5K_ANTMODE_SECTOR_STA
:
2013 tx_ant
= 1; /* variable */
2014 use_def_for_tx
= true;
2015 update_def_on_tx
= false;
2016 use_def_for_rts
= true;
2017 use_def_for_sg
= false;
2020 case AR5K_ANTMODE_DEBUG
:
2023 use_def_for_tx
= false;
2024 update_def_on_tx
= false;
2025 use_def_for_rts
= false;
2026 use_def_for_sg
= false;
2033 ah
->ah_tx_ant
= tx_ant
;
2034 ah
->ah_ant_mode
= ant_mode
;
2035 ah
->ah_def_ant
= def_ant
;
2037 sta_id1
|= use_def_for_tx
? AR5K_STA_ID1_DEFAULT_ANTENNA
: 0;
2038 sta_id1
|= update_def_on_tx
? AR5K_STA_ID1_DESC_ANTENNA
: 0;
2039 sta_id1
|= use_def_for_rts
? AR5K_STA_ID1_RTS_DEF_ANTENNA
: 0;
2040 sta_id1
|= use_def_for_sg
? AR5K_STA_ID1_SELFGEN_DEF_ANT
: 0;
2042 AR5K_REG_DISABLE_BITS(ah
, AR5K_STA_ID1
, AR5K_STA_ID1_ANTENNA_SETTINGS
);
2045 AR5K_REG_ENABLE_BITS(ah
, AR5K_STA_ID1
, sta_id1
);
2047 ath5k_hw_set_antenna_switch(ah
, ee_mode
);
2048 /* Note: set diversity before default antenna
2049 * because it won't work correctly */
2050 ath5k_hw_set_fast_div(ah
, ee_mode
, fast_div
);
2051 ath5k_hw_set_def_antenna(ah
, def_ant
);
2064 * Do linear interpolation between two given (x, y) points
2067 ath5k_get_interpolated_value(s16 target
, s16 x_left
, s16 x_right
,
2068 s16 y_left
, s16 y_right
)
2072 /* Avoid divide by zero and skip interpolation
2073 * if we have the same point */
2074 if ((x_left
== x_right
) || (y_left
== y_right
))
2078 * Since we use ints and not fps, we need to scale up in
2079 * order to get a sane ratio value (or else we 'll eg. get
2080 * always 1 instead of 1.25, 1.75 etc). We scale up by 100
2081 * to have some accuracy both for 0.5 and 0.25 steps.
2083 ratio
= ((100 * y_right
- 100 * y_left
) / (x_right
- x_left
));
2085 /* Now scale down to be in range */
2086 result
= y_left
+ (ratio
* (target
- x_left
) / 100);
2092 * Find vertical boundary (min pwr) for the linear PCDAC curve.
2094 * Since we have the top of the curve and we draw the line below
2095 * until we reach 1 (1 pcdac step) we need to know which point
2096 * (x value) that is so that we don't go below y axis and have negative
2097 * pcdac values when creating the curve, or fill the table with zeroes.
2100 ath5k_get_linear_pcdac_min(const u8
*stepL
, const u8
*stepR
,
2101 const s16
*pwrL
, const s16
*pwrR
)
2104 s16 min_pwrL
, min_pwrR
;
2107 /* Some vendors write the same pcdac value twice !!! */
2108 if (stepL
[0] == stepL
[1] || stepR
[0] == stepR
[1])
2109 return max(pwrL
[0], pwrR
[0]);
2111 if (pwrL
[0] == pwrL
[1])
2117 tmp
= (s8
) ath5k_get_interpolated_value(pwr_i
,
2119 stepL
[0], stepL
[1]);
2125 if (pwrR
[0] == pwrR
[1])
2131 tmp
= (s8
) ath5k_get_interpolated_value(pwr_i
,
2133 stepR
[0], stepR
[1]);
2139 /* Keep the right boundary so that it works for both curves */
2140 return max(min_pwrL
, min_pwrR
);
2144 * Interpolate (pwr,vpd) points to create a Power to PDADC or a
2145 * Power to PCDAC curve.
2147 * Each curve has power on x axis (in 0.5dB units) and PCDAC/PDADC
2148 * steps (offsets) on y axis. Power can go up to 31.5dB and max
2149 * PCDAC/PDADC step for each curve is 64 but we can write more than
2150 * one curves on hw so we can go up to 128 (which is the max step we
2151 * can write on the final table).
2153 * We write y values (PCDAC/PDADC steps) on hw.
2156 ath5k_create_power_curve(s16 pmin
, s16 pmax
,
2157 const s16
*pwr
, const u8
*vpd
,
2159 u8
*vpd_table
, u8 type
)
2161 u8 idx
[2] = { 0, 1 };
2162 s16 pwr_i
= 2 * pmin
;
2168 /* We want the whole line, so adjust boundaries
2169 * to cover the entire power range. Note that
2170 * power values are already 0.25dB so no need
2171 * to multiply pwr_i by 2 */
2172 if (type
== AR5K_PWRTABLE_LINEAR_PCDAC
) {
2178 /* Find surrounding turning points (TPs)
2179 * and interpolate between them */
2180 for (i
= 0; (i
<= (u16
) (pmax
- pmin
)) &&
2181 (i
< AR5K_EEPROM_POWER_TABLE_SIZE
); i
++) {
2183 /* We passed the right TP, move to the next set of TPs
2184 * if we pass the last TP, extrapolate above using the last
2185 * two TPs for ratio */
2186 if ((pwr_i
> pwr
[idx
[1]]) && (idx
[1] < num_points
- 1)) {
2191 vpd_table
[i
] = (u8
) ath5k_get_interpolated_value(pwr_i
,
2192 pwr
[idx
[0]], pwr
[idx
[1]],
2193 vpd
[idx
[0]], vpd
[idx
[1]]);
2195 /* Increase by 0.5dB
2196 * (0.25 dB units) */
2202 * Get the surrounding per-channel power calibration piers
2203 * for a given frequency so that we can interpolate between
2204 * them and come up with an appropriate dataset for our current
2208 ath5k_get_chan_pcal_surrounding_piers(struct ath5k_hw
*ah
,
2209 struct ieee80211_channel
*channel
,
2210 struct ath5k_chan_pcal_info
**pcinfo_l
,
2211 struct ath5k_chan_pcal_info
**pcinfo_r
)
2213 struct ath5k_eeprom_info
*ee
= &ah
->ah_capabilities
.cap_eeprom
;
2214 struct ath5k_chan_pcal_info
*pcinfo
;
2217 u32 target
= channel
->center_freq
;
2222 if (!(channel
->hw_value
& CHANNEL_OFDM
)) {
2223 pcinfo
= ee
->ee_pwr_cal_b
;
2224 mode
= AR5K_EEPROM_MODE_11B
;
2225 } else if (channel
->hw_value
& CHANNEL_2GHZ
) {
2226 pcinfo
= ee
->ee_pwr_cal_g
;
2227 mode
= AR5K_EEPROM_MODE_11G
;
2229 pcinfo
= ee
->ee_pwr_cal_a
;
2230 mode
= AR5K_EEPROM_MODE_11A
;
2232 max
= ee
->ee_n_piers
[mode
] - 1;
2234 /* Frequency is below our calibrated
2235 * range. Use the lowest power curve
2237 if (target
< pcinfo
[0].freq
) {
2242 /* Frequency is above our calibrated
2243 * range. Use the highest power curve
2245 if (target
> pcinfo
[max
].freq
) {
2246 idx_l
= idx_r
= max
;
2250 /* Frequency is inside our calibrated
2251 * channel range. Pick the surrounding
2252 * calibration piers so that we can
2254 for (i
= 0; i
<= max
; i
++) {
2256 /* Frequency matches one of our calibration
2257 * piers, no need to interpolate, just use
2258 * that calibration pier */
2259 if (pcinfo
[i
].freq
== target
) {
2264 /* We found a calibration pier that's above
2265 * frequency, use this pier and the previous
2266 * one to interpolate */
2267 if (target
< pcinfo
[i
].freq
) {
2275 *pcinfo_l
= &pcinfo
[idx_l
];
2276 *pcinfo_r
= &pcinfo
[idx_r
];
2280 * Get the surrounding per-rate power calibration data
2281 * for a given frequency and interpolate between power
2282 * values to set max target power supported by hw for
2286 ath5k_get_rate_pcal_data(struct ath5k_hw
*ah
,
2287 struct ieee80211_channel
*channel
,
2288 struct ath5k_rate_pcal_info
*rates
)
2290 struct ath5k_eeprom_info
*ee
= &ah
->ah_capabilities
.cap_eeprom
;
2291 struct ath5k_rate_pcal_info
*rpinfo
;
2294 u32 target
= channel
->center_freq
;
2299 if (!(channel
->hw_value
& CHANNEL_OFDM
)) {
2300 rpinfo
= ee
->ee_rate_tpwr_b
;
2301 mode
= AR5K_EEPROM_MODE_11B
;
2302 } else if (channel
->hw_value
& CHANNEL_2GHZ
) {
2303 rpinfo
= ee
->ee_rate_tpwr_g
;
2304 mode
= AR5K_EEPROM_MODE_11G
;
2306 rpinfo
= ee
->ee_rate_tpwr_a
;
2307 mode
= AR5K_EEPROM_MODE_11A
;
2309 max
= ee
->ee_rate_target_pwr_num
[mode
] - 1;
2311 /* Get the surrounding calibration
2312 * piers - same as above */
2313 if (target
< rpinfo
[0].freq
) {
2318 if (target
> rpinfo
[max
].freq
) {
2319 idx_l
= idx_r
= max
;
2323 for (i
= 0; i
<= max
; i
++) {
2325 if (rpinfo
[i
].freq
== target
) {
2330 if (target
< rpinfo
[i
].freq
) {
2338 /* Now interpolate power value, based on the frequency */
2339 rates
->freq
= target
;
2341 rates
->target_power_6to24
=
2342 ath5k_get_interpolated_value(target
, rpinfo
[idx_l
].freq
,
2344 rpinfo
[idx_l
].target_power_6to24
,
2345 rpinfo
[idx_r
].target_power_6to24
);
2347 rates
->target_power_36
=
2348 ath5k_get_interpolated_value(target
, rpinfo
[idx_l
].freq
,
2350 rpinfo
[idx_l
].target_power_36
,
2351 rpinfo
[idx_r
].target_power_36
);
2353 rates
->target_power_48
=
2354 ath5k_get_interpolated_value(target
, rpinfo
[idx_l
].freq
,
2356 rpinfo
[idx_l
].target_power_48
,
2357 rpinfo
[idx_r
].target_power_48
);
2359 rates
->target_power_54
=
2360 ath5k_get_interpolated_value(target
, rpinfo
[idx_l
].freq
,
2362 rpinfo
[idx_l
].target_power_54
,
2363 rpinfo
[idx_r
].target_power_54
);
2367 * Get the max edge power for this channel if
2368 * we have such data from EEPROM's Conformance Test
2369 * Limits (CTL), and limit max power if needed.
2372 ath5k_get_max_ctl_power(struct ath5k_hw
*ah
,
2373 struct ieee80211_channel
*channel
)
2375 struct ath_regulatory
*regulatory
= ath5k_hw_regulatory(ah
);
2376 struct ath5k_eeprom_info
*ee
= &ah
->ah_capabilities
.cap_eeprom
;
2377 struct ath5k_edge_power
*rep
= ee
->ee_ctl_pwr
;
2378 u8
*ctl_val
= ee
->ee_ctl
;
2379 s16 max_chan_pwr
= ah
->ah_txpower
.txp_max_pwr
/ 4;
2384 u32 target
= channel
->center_freq
;
2386 ctl_mode
= ath_regd_get_band_ctl(regulatory
, channel
->band
);
2388 switch (channel
->hw_value
& CHANNEL_MODES
) {
2390 if (ah
->ah_bwmode
== AR5K_BWMODE_40MHZ
)
2391 ctl_mode
|= AR5K_CTL_TURBO
;
2393 ctl_mode
|= AR5K_CTL_11A
;
2396 if (ah
->ah_bwmode
== AR5K_BWMODE_40MHZ
)
2397 ctl_mode
|= AR5K_CTL_TURBOG
;
2399 ctl_mode
|= AR5K_CTL_11G
;
2402 ctl_mode
|= AR5K_CTL_11B
;
2410 for (i
= 0; i
< ee
->ee_ctls
; i
++) {
2411 if (ctl_val
[i
] == ctl_mode
) {
2417 /* If we have a CTL dataset available grab it and find the
2418 * edge power for our frequency */
2419 if (ctl_idx
== 0xFF)
2422 /* Edge powers are sorted by frequency from lower
2423 * to higher. Each CTL corresponds to 8 edge power
2425 rep_idx
= ctl_idx
* AR5K_EEPROM_N_EDGES
;
2427 /* Don't do boundaries check because we
2428 * might have more that one bands defined
2431 /* Get the edge power that's closer to our
2433 for (i
= 0; i
< AR5K_EEPROM_N_EDGES
; i
++) {
2435 if (target
<= rep
[rep_idx
].freq
)
2436 edge_pwr
= (s16
) rep
[rep_idx
].edge
;
2440 ah
->ah_txpower
.txp_max_pwr
= 4 * min(edge_pwr
, max_chan_pwr
);
2445 * Power to PCDAC table functions
2449 * Fill Power to PCDAC table on RF5111
2451 * No further processing is needed for RF5111, the only thing we have to
2452 * do is fill the values below and above calibration range since eeprom data
2453 * may not cover the entire PCDAC table.
2456 ath5k_fill_pwr_to_pcdac_table(struct ath5k_hw
*ah
, s16
* table_min
,
2459 u8
*pcdac_out
= ah
->ah_txpower
.txp_pd_table
;
2460 u8
*pcdac_tmp
= ah
->ah_txpower
.tmpL
[0];
2461 u8 pcdac_0
, pcdac_n
, pcdac_i
, pwr_idx
, i
;
2462 s16 min_pwr
, max_pwr
;
2464 /* Get table boundaries */
2465 min_pwr
= table_min
[0];
2466 pcdac_0
= pcdac_tmp
[0];
2468 max_pwr
= table_max
[0];
2469 pcdac_n
= pcdac_tmp
[table_max
[0] - table_min
[0]];
2471 /* Extrapolate below minimum using pcdac_0 */
2473 for (i
= 0; i
< min_pwr
; i
++)
2474 pcdac_out
[pcdac_i
++] = pcdac_0
;
2476 /* Copy values from pcdac_tmp */
2478 for (i
= 0; pwr_idx
<= max_pwr
&&
2479 pcdac_i
< AR5K_EEPROM_POWER_TABLE_SIZE
; i
++) {
2480 pcdac_out
[pcdac_i
++] = pcdac_tmp
[i
];
2484 /* Extrapolate above maximum */
2485 while (pcdac_i
< AR5K_EEPROM_POWER_TABLE_SIZE
)
2486 pcdac_out
[pcdac_i
++] = pcdac_n
;
2491 * Combine available XPD Curves and fill Linear Power to PCDAC table
2494 * RFX112 can have up to 2 curves (one for low txpower range and one for
2495 * higher txpower range). We need to put them both on pcdac_out and place
2496 * them in the correct location. In case we only have one curve available
2497 * just fit it on pcdac_out (it's supposed to cover the entire range of
2498 * available pwr levels since it's always the higher power curve). Extrapolate
2499 * below and above final table if needed.
2502 ath5k_combine_linear_pcdac_curves(struct ath5k_hw
*ah
, s16
* table_min
,
2503 s16
*table_max
, u8 pdcurves
)
2505 u8
*pcdac_out
= ah
->ah_txpower
.txp_pd_table
;
2512 s16 mid_pwr_idx
= 0;
2513 /* Edge flag turns on the 7nth bit on the PCDAC
2514 * to declare the higher power curve (force values
2515 * to be greater than 64). If we only have one curve
2516 * we don't need to set this, if we have 2 curves and
2517 * fill the table backwards this can also be used to
2518 * switch from higher power curve to lower power curve */
2522 /* When we have only one curve available
2523 * that's the higher power curve. If we have
2524 * two curves the first is the high power curve
2525 * and the next is the low power curve. */
2527 pcdac_low_pwr
= ah
->ah_txpower
.tmpL
[1];
2528 pcdac_high_pwr
= ah
->ah_txpower
.tmpL
[0];
2529 mid_pwr_idx
= table_max
[1] - table_min
[1] - 1;
2530 max_pwr_idx
= (table_max
[0] - table_min
[0]) / 2;
2532 /* If table size goes beyond 31.5dB, keep the
2533 * upper 31.5dB range when setting tx power.
2534 * Note: 126 = 31.5 dB in quarter dB steps */
2535 if (table_max
[0] - table_min
[1] > 126)
2536 min_pwr_idx
= table_max
[0] - 126;
2538 min_pwr_idx
= table_min
[1];
2540 /* Since we fill table backwards
2541 * start from high power curve */
2542 pcdac_tmp
= pcdac_high_pwr
;
2546 pcdac_low_pwr
= ah
->ah_txpower
.tmpL
[1]; /* Zeroed */
2547 pcdac_high_pwr
= ah
->ah_txpower
.tmpL
[0];
2548 min_pwr_idx
= table_min
[0];
2549 max_pwr_idx
= (table_max
[0] - table_min
[0]) / 2;
2550 pcdac_tmp
= pcdac_high_pwr
;
2554 /* This is used when setting tx power*/
2555 ah
->ah_txpower
.txp_min_idx
= min_pwr_idx
/ 2;
2557 /* Fill Power to PCDAC table backwards */
2559 for (i
= 63; i
>= 0; i
--) {
2560 /* Entering lower power range, reset
2561 * edge flag and set pcdac_tmp to lower
2563 if (edge_flag
== 0x40 &&
2564 (2 * pwr
<= (table_max
[1] - table_min
[0]) || pwr
== 0)) {
2566 pcdac_tmp
= pcdac_low_pwr
;
2567 pwr
= mid_pwr_idx
/ 2;
2570 /* Don't go below 1, extrapolate below if we have
2571 * already switched to the lower power curve -or
2572 * we only have one curve and edge_flag is zero
2574 if (pcdac_tmp
[pwr
] < 1 && (edge_flag
== 0x00)) {
2576 pcdac_out
[i
] = pcdac_out
[i
+ 1];
2582 pcdac_out
[i
] = pcdac_tmp
[pwr
] | edge_flag
;
2584 /* Extrapolate above if pcdac is greater than
2585 * 126 -this can happen because we OR pcdac_out
2586 * value with edge_flag on high power curve */
2587 if (pcdac_out
[i
] > 126)
2590 /* Decrease by a 0.5dB step */
2595 /* Write PCDAC values on hw */
2597 ath5k_write_pcdac_table(struct ath5k_hw
*ah
)
2599 u8
*pcdac_out
= ah
->ah_txpower
.txp_pd_table
;
2603 * Write TX power values
2605 for (i
= 0; i
< (AR5K_EEPROM_POWER_TABLE_SIZE
/ 2); i
++) {
2606 ath5k_hw_reg_write(ah
,
2607 (((pcdac_out
[2 * i
+ 0] << 8 | 0xff) & 0xffff) << 0) |
2608 (((pcdac_out
[2 * i
+ 1] << 8 | 0xff) & 0xffff) << 16),
2609 AR5K_PHY_PCDAC_TXPOWER(i
));
2615 * Power to PDADC table functions
2619 * Set the gain boundaries and create final Power to PDADC table
2621 * We can have up to 4 pd curves, we need to do a similar process
2622 * as we do for RF5112. This time we don't have an edge_flag but we
2623 * set the gain boundaries on a separate register.
2626 ath5k_combine_pwr_to_pdadc_curves(struct ath5k_hw
*ah
,
2627 s16
*pwr_min
, s16
*pwr_max
, u8 pdcurves
)
2629 u8 gain_boundaries
[AR5K_EEPROM_N_PD_GAINS
];
2630 u8
*pdadc_out
= ah
->ah_txpower
.txp_pd_table
;
2633 u8 pdadc_i
, pdadc_n
, pwr_step
, pdg
, max_idx
, table_size
;
2636 /* Note: Register value is initialized on initvals
2637 * there is no feedback from hw.
2638 * XXX: What about pd_gain_overlap from EEPROM ? */
2639 pd_gain_overlap
= (u8
) ath5k_hw_reg_read(ah
, AR5K_PHY_TPC_RG5
) &
2640 AR5K_PHY_TPC_RG5_PD_GAIN_OVERLAP
;
2642 /* Create final PDADC table */
2643 for (pdg
= 0, pdadc_i
= 0; pdg
< pdcurves
; pdg
++) {
2644 pdadc_tmp
= ah
->ah_txpower
.tmpL
[pdg
];
2646 if (pdg
== pdcurves
- 1)
2647 /* 2 dB boundary stretch for last
2648 * (higher power) curve */
2649 gain_boundaries
[pdg
] = pwr_max
[pdg
] + 4;
2651 /* Set gain boundary in the middle
2652 * between this curve and the next one */
2653 gain_boundaries
[pdg
] =
2654 (pwr_max
[pdg
] + pwr_min
[pdg
+ 1]) / 2;
2656 /* Sanity check in case our 2 db stretch got out of
2658 if (gain_boundaries
[pdg
] > AR5K_TUNE_MAX_TXPOWER
)
2659 gain_boundaries
[pdg
] = AR5K_TUNE_MAX_TXPOWER
;
2661 /* For the first curve (lower power)
2662 * start from 0 dB */
2666 /* For the other curves use the gain overlap */
2667 pdadc_0
= (gain_boundaries
[pdg
- 1] - pwr_min
[pdg
]) -
2670 /* Force each power step to be at least 0.5 dB */
2671 if ((pdadc_tmp
[1] - pdadc_tmp
[0]) > 1)
2672 pwr_step
= pdadc_tmp
[1] - pdadc_tmp
[0];
2676 /* If pdadc_0 is negative, we need to extrapolate
2677 * below this pdgain by a number of pwr_steps */
2678 while ((pdadc_0
< 0) && (pdadc_i
< 128)) {
2679 s16 tmp
= pdadc_tmp
[0] + pdadc_0
* pwr_step
;
2680 pdadc_out
[pdadc_i
++] = (tmp
< 0) ? 0 : (u8
) tmp
;
2684 /* Set last pwr level, using gain boundaries */
2685 pdadc_n
= gain_boundaries
[pdg
] + pd_gain_overlap
- pwr_min
[pdg
];
2686 /* Limit it to be inside pwr range */
2687 table_size
= pwr_max
[pdg
] - pwr_min
[pdg
];
2688 max_idx
= (pdadc_n
< table_size
) ? pdadc_n
: table_size
;
2690 /* Fill pdadc_out table */
2691 while (pdadc_0
< max_idx
&& pdadc_i
< 128)
2692 pdadc_out
[pdadc_i
++] = pdadc_tmp
[pdadc_0
++];
2694 /* Need to extrapolate above this pdgain? */
2695 if (pdadc_n
<= max_idx
)
2698 /* Force each power step to be at least 0.5 dB */
2699 if ((pdadc_tmp
[table_size
- 1] - pdadc_tmp
[table_size
- 2]) > 1)
2700 pwr_step
= pdadc_tmp
[table_size
- 1] -
2701 pdadc_tmp
[table_size
- 2];
2705 /* Extrapolate above */
2706 while ((pdadc_0
< (s16
) pdadc_n
) &&
2707 (pdadc_i
< AR5K_EEPROM_POWER_TABLE_SIZE
* 2)) {
2708 s16 tmp
= pdadc_tmp
[table_size
- 1] +
2709 (pdadc_0
- max_idx
) * pwr_step
;
2710 pdadc_out
[pdadc_i
++] = (tmp
> 127) ? 127 : (u8
) tmp
;
2715 while (pdg
< AR5K_EEPROM_N_PD_GAINS
) {
2716 gain_boundaries
[pdg
] = gain_boundaries
[pdg
- 1];
2720 while (pdadc_i
< AR5K_EEPROM_POWER_TABLE_SIZE
* 2) {
2721 pdadc_out
[pdadc_i
] = pdadc_out
[pdadc_i
- 1];
2725 /* Set gain boundaries */
2726 ath5k_hw_reg_write(ah
,
2727 AR5K_REG_SM(pd_gain_overlap
,
2728 AR5K_PHY_TPC_RG5_PD_GAIN_OVERLAP
) |
2729 AR5K_REG_SM(gain_boundaries
[0],
2730 AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_1
) |
2731 AR5K_REG_SM(gain_boundaries
[1],
2732 AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_2
) |
2733 AR5K_REG_SM(gain_boundaries
[2],
2734 AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_3
) |
2735 AR5K_REG_SM(gain_boundaries
[3],
2736 AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_4
),
2739 /* Used for setting rate power table */
2740 ah
->ah_txpower
.txp_min_idx
= pwr_min
[0];
2744 /* Write PDADC values on hw */
2746 ath5k_write_pwr_to_pdadc_table(struct ath5k_hw
*ah
, u8 ee_mode
)
2748 struct ath5k_eeprom_info
*ee
= &ah
->ah_capabilities
.cap_eeprom
;
2749 u8
*pdadc_out
= ah
->ah_txpower
.txp_pd_table
;
2750 u8
*pdg_to_idx
= ee
->ee_pdc_to_idx
[ee_mode
];
2751 u8 pdcurves
= ee
->ee_pd_gains
[ee_mode
];
2755 /* Select the right pdgain curves */
2757 /* Clear current settings */
2758 reg
= ath5k_hw_reg_read(ah
, AR5K_PHY_TPC_RG1
);
2759 reg
&= ~(AR5K_PHY_TPC_RG1_PDGAIN_1
|
2760 AR5K_PHY_TPC_RG1_PDGAIN_2
|
2761 AR5K_PHY_TPC_RG1_PDGAIN_3
|
2762 AR5K_PHY_TPC_RG1_NUM_PD_GAIN
);
2765 * Use pd_gains curve from eeprom
2767 * This overrides the default setting from initvals
2768 * in case some vendors (e.g. Zcomax) don't use the default
2769 * curves. If we don't honor their settings we 'll get a
2770 * 5dB (1 * gain overlap ?) drop.
2772 reg
|= AR5K_REG_SM(pdcurves
, AR5K_PHY_TPC_RG1_NUM_PD_GAIN
);
2776 reg
|= AR5K_REG_SM(pdg_to_idx
[2], AR5K_PHY_TPC_RG1_PDGAIN_3
);
2779 reg
|= AR5K_REG_SM(pdg_to_idx
[1], AR5K_PHY_TPC_RG1_PDGAIN_2
);
2782 reg
|= AR5K_REG_SM(pdg_to_idx
[0], AR5K_PHY_TPC_RG1_PDGAIN_1
);
2785 ath5k_hw_reg_write(ah
, reg
, AR5K_PHY_TPC_RG1
);
2788 * Write TX power values
2790 for (i
= 0; i
< (AR5K_EEPROM_POWER_TABLE_SIZE
/ 2); i
++) {
2791 ath5k_hw_reg_write(ah
,
2792 ((pdadc_out
[4 * i
+ 0] & 0xff) << 0) |
2793 ((pdadc_out
[4 * i
+ 1] & 0xff) << 8) |
2794 ((pdadc_out
[4 * i
+ 2] & 0xff) << 16) |
2795 ((pdadc_out
[4 * i
+ 3] & 0xff) << 24),
2796 AR5K_PHY_PDADC_TXPOWER(i
));
2802 * Common code for PCDAC/PDADC tables
2806 * This is the main function that uses all of the above
2807 * to set PCDAC/PDADC table on hw for the current channel.
2808 * This table is used for tx power calibration on the baseband,
2809 * without it we get weird tx power levels and in some cases
2810 * distorted spectral mask
2813 ath5k_setup_channel_powertable(struct ath5k_hw
*ah
,
2814 struct ieee80211_channel
*channel
,
2815 u8 ee_mode
, u8 type
)
2817 struct ath5k_pdgain_info
*pdg_L
, *pdg_R
;
2818 struct ath5k_chan_pcal_info
*pcinfo_L
;
2819 struct ath5k_chan_pcal_info
*pcinfo_R
;
2820 struct ath5k_eeprom_info
*ee
= &ah
->ah_capabilities
.cap_eeprom
;
2821 u8
*pdg_curve_to_idx
= ee
->ee_pdc_to_idx
[ee_mode
];
2822 s16 table_min
[AR5K_EEPROM_N_PD_GAINS
];
2823 s16 table_max
[AR5K_EEPROM_N_PD_GAINS
];
2826 u32 target
= channel
->center_freq
;
2829 /* Get surrounding freq piers for this channel */
2830 ath5k_get_chan_pcal_surrounding_piers(ah
, channel
,
2834 /* Loop over pd gain curves on
2835 * surrounding freq piers by index */
2836 for (pdg
= 0; pdg
< ee
->ee_pd_gains
[ee_mode
]; pdg
++) {
2838 /* Fill curves in reverse order
2839 * from lower power (max gain)
2840 * to higher power. Use curve -> idx
2841 * backmapping we did on eeprom init */
2842 u8 idx
= pdg_curve_to_idx
[pdg
];
2844 /* Grab the needed curves by index */
2845 pdg_L
= &pcinfo_L
->pd_curves
[idx
];
2846 pdg_R
= &pcinfo_R
->pd_curves
[idx
];
2848 /* Initialize the temp tables */
2849 tmpL
= ah
->ah_txpower
.tmpL
[pdg
];
2850 tmpR
= ah
->ah_txpower
.tmpR
[pdg
];
2852 /* Set curve's x boundaries and create
2853 * curves so that they cover the same
2854 * range (if we don't do that one table
2855 * will have values on some range and the
2856 * other one won't have any so interpolation
2858 table_min
[pdg
] = min(pdg_L
->pd_pwr
[0],
2859 pdg_R
->pd_pwr
[0]) / 2;
2861 table_max
[pdg
] = max(pdg_L
->pd_pwr
[pdg_L
->pd_points
- 1],
2862 pdg_R
->pd_pwr
[pdg_R
->pd_points
- 1]) / 2;
2864 /* Now create the curves on surrounding channels
2865 * and interpolate if needed to get the final
2866 * curve for this gain on this channel */
2868 case AR5K_PWRTABLE_LINEAR_PCDAC
:
2869 /* Override min/max so that we don't loose
2870 * accuracy (don't divide by 2) */
2871 table_min
[pdg
] = min(pdg_L
->pd_pwr
[0],
2875 max(pdg_L
->pd_pwr
[pdg_L
->pd_points
- 1],
2876 pdg_R
->pd_pwr
[pdg_R
->pd_points
- 1]);
2878 /* Override minimum so that we don't get
2879 * out of bounds while extrapolating
2880 * below. Don't do this when we have 2
2881 * curves and we are on the high power curve
2882 * because table_min is ok in this case */
2883 if (!(ee
->ee_pd_gains
[ee_mode
] > 1 && pdg
== 0)) {
2886 ath5k_get_linear_pcdac_min(pdg_L
->pd_step
,
2891 /* Don't go too low because we will
2892 * miss the upper part of the curve.
2893 * Note: 126 = 31.5dB (max power supported)
2894 * in 0.25dB units */
2895 if (table_max
[pdg
] - table_min
[pdg
] > 126)
2896 table_min
[pdg
] = table_max
[pdg
] - 126;
2900 case AR5K_PWRTABLE_PWR_TO_PCDAC
:
2901 case AR5K_PWRTABLE_PWR_TO_PDADC
:
2903 ath5k_create_power_curve(table_min
[pdg
],
2907 pdg_L
->pd_points
, tmpL
, type
);
2909 /* We are in a calibration
2910 * pier, no need to interpolate
2911 * between freq piers */
2912 if (pcinfo_L
== pcinfo_R
)
2915 ath5k_create_power_curve(table_min
[pdg
],
2919 pdg_R
->pd_points
, tmpR
, type
);
2925 /* Interpolate between curves
2926 * of surrounding freq piers to
2927 * get the final curve for this
2928 * pd gain. Re-use tmpL for interpolation
2930 for (i
= 0; (i
< (u16
) (table_max
[pdg
] - table_min
[pdg
])) &&
2931 (i
< AR5K_EEPROM_POWER_TABLE_SIZE
); i
++) {
2932 tmpL
[i
] = (u8
) ath5k_get_interpolated_value(target
,
2933 (s16
) pcinfo_L
->freq
,
2934 (s16
) pcinfo_R
->freq
,
2940 /* Now we have a set of curves for this
2941 * channel on tmpL (x range is table_max - table_min
2942 * and y values are tmpL[pdg][]) sorted in the same
2943 * order as EEPROM (because we've used the backmapping).
2944 * So for RF5112 it's from higher power to lower power
2945 * and for RF2413 it's from lower power to higher power.
2946 * For RF5111 we only have one curve. */
2948 /* Fill min and max power levels for this
2949 * channel by interpolating the values on
2950 * surrounding channels to complete the dataset */
2951 ah
->ah_txpower
.txp_min_pwr
= ath5k_get_interpolated_value(target
,
2952 (s16
) pcinfo_L
->freq
,
2953 (s16
) pcinfo_R
->freq
,
2954 pcinfo_L
->min_pwr
, pcinfo_R
->min_pwr
);
2956 ah
->ah_txpower
.txp_max_pwr
= ath5k_get_interpolated_value(target
,
2957 (s16
) pcinfo_L
->freq
,
2958 (s16
) pcinfo_R
->freq
,
2959 pcinfo_L
->max_pwr
, pcinfo_R
->max_pwr
);
2961 /* Fill PCDAC/PDADC table */
2963 case AR5K_PWRTABLE_LINEAR_PCDAC
:
2964 /* For RF5112 we can have one or two curves
2965 * and each curve covers a certain power lvl
2966 * range so we need to do some more processing */
2967 ath5k_combine_linear_pcdac_curves(ah
, table_min
, table_max
,
2968 ee
->ee_pd_gains
[ee_mode
]);
2970 /* Set txp.offset so that we can
2971 * match max power value with max
2973 ah
->ah_txpower
.txp_offset
= 64 - (table_max
[0] / 2);
2975 case AR5K_PWRTABLE_PWR_TO_PCDAC
:
2976 /* We are done for RF5111 since it has only
2977 * one curve, just fit the curve on the table */
2978 ath5k_fill_pwr_to_pcdac_table(ah
, table_min
, table_max
);
2980 /* No rate powertable adjustment for RF5111 */
2981 ah
->ah_txpower
.txp_min_idx
= 0;
2982 ah
->ah_txpower
.txp_offset
= 0;
2984 case AR5K_PWRTABLE_PWR_TO_PDADC
:
2985 /* Set PDADC boundaries and fill
2986 * final PDADC table */
2987 ath5k_combine_pwr_to_pdadc_curves(ah
, table_min
, table_max
,
2988 ee
->ee_pd_gains
[ee_mode
]);
2990 /* Set txp.offset, note that table_min
2991 * can be negative */
2992 ah
->ah_txpower
.txp_offset
= table_min
[0];
2998 ah
->ah_txpower
.txp_setup
= true;
3003 /* Write power table for current channel to hw */
3005 ath5k_write_channel_powertable(struct ath5k_hw
*ah
, u8 ee_mode
, u8 type
)
3007 if (type
== AR5K_PWRTABLE_PWR_TO_PDADC
)
3008 ath5k_write_pwr_to_pdadc_table(ah
, ee_mode
);
3010 ath5k_write_pcdac_table(ah
);
3014 * Per-rate tx power setting
3016 * This is the code that sets the desired tx power (below
3017 * maximum) on hw for each rate (we also have TPC that sets
3018 * power per packet). We do that by providing an index on the
3019 * PCDAC/PDADC table we set up.
3023 * Set rate power table
3025 * For now we only limit txpower based on maximum tx power
3026 * supported by hw (what's inside rate_info). We need to limit
3027 * this even more, based on regulatory domain etc.
3029 * Rate power table contains indices to PCDAC/PDADC table (0.5dB steps)
3030 * and is indexed as follows:
3031 * rates[0] - rates[7] -> OFDM rates
3032 * rates[8] - rates[14] -> CCK rates
3033 * rates[15] -> XR rates (they all have the same power)
3036 ath5k_setup_rate_powertable(struct ath5k_hw
*ah
, u16 max_pwr
,
3037 struct ath5k_rate_pcal_info
*rate_info
,
3043 /* max_pwr is power level we got from driver/user in 0.5dB
3044 * units, switch to 0.25dB units so we can compare */
3046 max_pwr
= min(max_pwr
, (u16
) ah
->ah_txpower
.txp_max_pwr
) / 2;
3048 /* apply rate limits */
3049 rates
= ah
->ah_txpower
.txp_rates_power_table
;
3051 /* OFDM rates 6 to 24Mb/s */
3052 for (i
= 0; i
< 5; i
++)
3053 rates
[i
] = min(max_pwr
, rate_info
->target_power_6to24
);
3055 /* Rest OFDM rates */
3056 rates
[5] = min(rates
[0], rate_info
->target_power_36
);
3057 rates
[6] = min(rates
[0], rate_info
->target_power_48
);
3058 rates
[7] = min(rates
[0], rate_info
->target_power_54
);
3062 rates
[8] = min(rates
[0], rate_info
->target_power_6to24
);
3064 rates
[9] = min(rates
[0], rate_info
->target_power_36
);
3066 rates
[10] = min(rates
[0], rate_info
->target_power_36
);
3068 rates
[11] = min(rates
[0], rate_info
->target_power_48
);
3070 rates
[12] = min(rates
[0], rate_info
->target_power_48
);
3072 rates
[13] = min(rates
[0], rate_info
->target_power_54
);
3074 rates
[14] = min(rates
[0], rate_info
->target_power_54
);
3077 rates
[15] = min(rates
[0], rate_info
->target_power_6to24
);
3079 /* CCK rates have different peak to average ratio
3080 * so we have to tweak their power so that gainf
3081 * correction works ok. For this we use OFDM to
3082 * CCK delta from eeprom */
3083 if ((ee_mode
== AR5K_EEPROM_MODE_11G
) &&
3084 (ah
->ah_phy_revision
< AR5K_SREV_PHY_5212A
))
3085 for (i
= 8; i
<= 15; i
++)
3086 rates
[i
] -= ah
->ah_txpower
.txp_cck_ofdm_gainf_delta
;
3088 /* Now that we have all rates setup use table offset to
3089 * match the power range set by user with the power indices
3090 * on PCDAC/PDADC table */
3091 for (i
= 0; i
< 16; i
++) {
3092 rates
[i
] += ah
->ah_txpower
.txp_offset
;
3093 /* Don't get out of bounds */
3098 /* Min/max in 0.25dB units */
3099 ah
->ah_txpower
.txp_min_pwr
= 2 * rates
[7];
3100 ah
->ah_txpower
.txp_cur_pwr
= 2 * rates
[0];
3101 ah
->ah_txpower
.txp_ofdm
= rates
[7];
3106 * Set transmission power
3109 ath5k_hw_txpower(struct ath5k_hw
*ah
, struct ieee80211_channel
*channel
,
3112 struct ath5k_rate_pcal_info rate_info
;
3113 struct ieee80211_channel
*curr_channel
= ah
->ah_current_channel
;
3118 if (txpower
> AR5K_TUNE_MAX_TXPOWER
) {
3119 ATH5K_ERR(ah
->ah_sc
, "invalid tx power: %u\n", txpower
);
3123 ee_mode
= ath5k_eeprom_mode_from_channel(channel
);
3125 ATH5K_ERR(ah
->ah_sc
,
3126 "invalid channel: %d\n", channel
->center_freq
);
3130 /* Initialize TX power table */
3131 switch (ah
->ah_radio
) {
3136 type
= AR5K_PWRTABLE_PWR_TO_PCDAC
;
3139 type
= AR5K_PWRTABLE_LINEAR_PCDAC
;
3146 type
= AR5K_PWRTABLE_PWR_TO_PDADC
;
3153 * If we don't change channel/mode skip tx powertable calculation
3154 * and use the cached one.
3156 if (!ah
->ah_txpower
.txp_setup
||
3157 (channel
->hw_value
!= curr_channel
->hw_value
) ||
3158 (channel
->center_freq
!= curr_channel
->center_freq
)) {
3159 /* Reset TX power values */
3160 memset(&ah
->ah_txpower
, 0, sizeof(ah
->ah_txpower
));
3161 ah
->ah_txpower
.txp_tpc
= AR5K_TUNE_TPC_TXPOWER
;
3163 /* Calculate the powertable */
3164 ret
= ath5k_setup_channel_powertable(ah
, channel
,
3170 /* Write table on hw */
3171 ath5k_write_channel_powertable(ah
, ee_mode
, type
);
3173 /* Limit max power if we have a CTL available */
3174 ath5k_get_max_ctl_power(ah
, channel
);
3176 /* FIXME: Antenna reduction stuff */
3178 /* FIXME: Limit power on turbo modes */
3180 /* FIXME: TPC scale reduction */
3182 /* Get surrounding channels for per-rate power table
3184 ath5k_get_rate_pcal_data(ah
, channel
, &rate_info
);
3186 /* Setup rate power table */
3187 ath5k_setup_rate_powertable(ah
, txpower
, &rate_info
, ee_mode
);
3189 /* Write rate power table on hw */
3190 ath5k_hw_reg_write(ah
, AR5K_TXPOWER_OFDM(3, 24) |
3191 AR5K_TXPOWER_OFDM(2, 16) | AR5K_TXPOWER_OFDM(1, 8) |
3192 AR5K_TXPOWER_OFDM(0, 0), AR5K_PHY_TXPOWER_RATE1
);
3194 ath5k_hw_reg_write(ah
, AR5K_TXPOWER_OFDM(7, 24) |
3195 AR5K_TXPOWER_OFDM(6, 16) | AR5K_TXPOWER_OFDM(5, 8) |
3196 AR5K_TXPOWER_OFDM(4, 0), AR5K_PHY_TXPOWER_RATE2
);
3198 ath5k_hw_reg_write(ah
, AR5K_TXPOWER_CCK(10, 24) |
3199 AR5K_TXPOWER_CCK(9, 16) | AR5K_TXPOWER_CCK(15, 8) |
3200 AR5K_TXPOWER_CCK(8, 0), AR5K_PHY_TXPOWER_RATE3
);
3202 ath5k_hw_reg_write(ah
, AR5K_TXPOWER_CCK(14, 24) |
3203 AR5K_TXPOWER_CCK(13, 16) | AR5K_TXPOWER_CCK(12, 8) |
3204 AR5K_TXPOWER_CCK(11, 0), AR5K_PHY_TXPOWER_RATE4
);
3206 /* FIXME: TPC support */
3207 if (ah
->ah_txpower
.txp_tpc
) {
3208 ath5k_hw_reg_write(ah
, AR5K_PHY_TXPOWER_RATE_MAX_TPC_ENABLE
|
3209 AR5K_TUNE_MAX_TXPOWER
, AR5K_PHY_TXPOWER_RATE_MAX
);
3211 ath5k_hw_reg_write(ah
,
3212 AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER
, AR5K_TPC_ACK
) |
3213 AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER
, AR5K_TPC_CTS
) |
3214 AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER
, AR5K_TPC_CHIRP
),
3217 ath5k_hw_reg_write(ah
, AR5K_PHY_TXPOWER_RATE_MAX
|
3218 AR5K_TUNE_MAX_TXPOWER
, AR5K_PHY_TXPOWER_RATE_MAX
);
3224 int ath5k_hw_set_txpower_limit(struct ath5k_hw
*ah
, u8 txpower
)
3226 ATH5K_DBG(ah
->ah_sc
, ATH5K_DEBUG_TXPOWER
,
3227 "changing txpower to %d\n", txpower
);
3229 return ath5k_hw_txpower(ah
, ah
->ah_current_channel
, txpower
);
3236 int ath5k_hw_phy_init(struct ath5k_hw
*ah
, struct ieee80211_channel
*channel
,
3239 struct ieee80211_channel
*curr_channel
;
3245 * Sanity check for fast flag
3246 * Don't try fast channel change when changing modulation
3247 * mode/band. We check for chip compatibility on
3250 curr_channel
= ah
->ah_current_channel
;
3251 if (fast
&& (channel
->hw_value
!= curr_channel
->hw_value
))
3255 * On fast channel change we only set the synth parameters
3256 * while PHY is running, enable calibration and skip the rest.
3259 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_RFBUS_REQ
,
3260 AR5K_PHY_RFBUS_REQ_REQUEST
);
3261 for (i
= 0; i
< 100; i
++) {
3262 if (ath5k_hw_reg_read(ah
, AR5K_PHY_RFBUS_GRANT
))
3270 /* Set channel and wait for synth */
3271 ret
= ath5k_hw_channel(ah
, channel
);
3275 ath5k_hw_wait_for_synth(ah
, channel
);
3281 * Note: We need to do that before we set
3282 * RF buffer settings on 5211/5212+ so that we
3283 * properly set curve indices.
3285 ret
= ath5k_hw_txpower(ah
, channel
, ah
->ah_txpower
.txp_cur_pwr
?
3286 ah
->ah_txpower
.txp_cur_pwr
/ 2 : AR5K_TUNE_MAX_TXPOWER
);
3290 /* Write OFDM timings on 5212*/
3291 if (ah
->ah_version
== AR5K_AR5212
&&
3292 channel
->hw_value
& CHANNEL_OFDM
) {
3294 ret
= ath5k_hw_write_ofdm_timings(ah
, channel
);
3298 /* Spur info is available only from EEPROM versions
3299 * greater than 5.3, but the EEPROM routines will use
3300 * static values for older versions */
3301 if (ah
->ah_mac_srev
>= AR5K_SREV_AR5424
)
3302 ath5k_hw_set_spur_mitigation_filter(ah
,
3306 /* If we used fast channel switching
3307 * we are done, release RF bus and
3308 * fire up NF calibration.
3310 * Note: Only NF calibration due to
3311 * channel change, not AGC calibration
3312 * since AGC is still running !
3316 * Release RF Bus grant
3318 AR5K_REG_DISABLE_BITS(ah
, AR5K_PHY_RFBUS_REQ
,
3319 AR5K_PHY_RFBUS_REQ_REQUEST
);
3322 * Start NF calibration
3324 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_AGCCTL
,
3325 AR5K_PHY_AGCCTL_NF
);
3331 * For 5210 we do all initialization using
3332 * initvals, so we don't have to modify
3333 * any settings (5210 also only supports
3336 if (ah
->ah_version
!= AR5K_AR5210
) {
3339 * Write initial RF gain settings
3340 * This should work for both 5111/5112
3342 ret
= ath5k_hw_rfgain_init(ah
, channel
->band
);
3351 ret
= ath5k_hw_rfregs_init(ah
, channel
, mode
);
3355 /*Enable/disable 802.11b mode on 5111
3356 (enable 2111 frequency converter + CCK)*/
3357 if (ah
->ah_radio
== AR5K_RF5111
) {
3358 if (mode
== AR5K_MODE_11B
)
3359 AR5K_REG_ENABLE_BITS(ah
, AR5K_TXCFG
,
3362 AR5K_REG_DISABLE_BITS(ah
, AR5K_TXCFG
,
3366 } else if (ah
->ah_version
== AR5K_AR5210
) {
3368 /* Disable phy and wait */
3369 ath5k_hw_reg_write(ah
, AR5K_PHY_ACT_DISABLE
, AR5K_PHY_ACT
);
3373 /* Set channel on PHY */
3374 ret
= ath5k_hw_channel(ah
, channel
);
3379 * Enable the PHY and wait until completion
3380 * This includes BaseBand and Synthesizer
3383 ath5k_hw_reg_write(ah
, AR5K_PHY_ACT_ENABLE
, AR5K_PHY_ACT
);
3385 ath5k_hw_wait_for_synth(ah
, channel
);
3388 * Perform ADC test to see if baseband is ready
3389 * Set tx hold and check adc test register
3391 phy_tst1
= ath5k_hw_reg_read(ah
, AR5K_PHY_TST1
);
3392 ath5k_hw_reg_write(ah
, AR5K_PHY_TST1_TXHOLD
, AR5K_PHY_TST1
);
3393 for (i
= 0; i
<= 20; i
++) {
3394 if (!(ath5k_hw_reg_read(ah
, AR5K_PHY_ADC_TEST
) & 0x10))
3398 ath5k_hw_reg_write(ah
, phy_tst1
, AR5K_PHY_TST1
);
3401 * Start automatic gain control calibration
3403 * During AGC calibration RX path is re-routed to
3404 * a power detector so we don't receive anything.
3406 * This method is used to calibrate some static offsets
3407 * used together with on-the fly I/Q calibration (the
3408 * one performed via ath5k_hw_phy_calibrate), which doesn't
3409 * interrupt rx path.
3411 * While rx path is re-routed to the power detector we also
3412 * start a noise floor calibration to measure the
3413 * card's noise floor (the noise we measure when we are not
3414 * transmitting or receiving anything).
3416 * If we are in a noisy environment, AGC calibration may time
3417 * out and/or noise floor calibration might timeout.
3419 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_AGCCTL
,
3420 AR5K_PHY_AGCCTL_CAL
| AR5K_PHY_AGCCTL_NF
);
3422 /* At the same time start I/Q calibration for QAM constellation
3423 * -no need for CCK- */
3424 ah
->ah_calibration
= false;
3425 if (!(mode
== AR5K_MODE_11B
)) {
3426 ah
->ah_calibration
= true;
3427 AR5K_REG_WRITE_BITS(ah
, AR5K_PHY_IQ
,
3428 AR5K_PHY_IQ_CAL_NUM_LOG_MAX
, 15);
3429 AR5K_REG_ENABLE_BITS(ah
, AR5K_PHY_IQ
,
3433 /* Wait for gain calibration to finish (we check for I/Q calibration
3434 * during ath5k_phy_calibrate) */
3435 if (ath5k_hw_register_timeout(ah
, AR5K_PHY_AGCCTL
,
3436 AR5K_PHY_AGCCTL_CAL
, 0, false)) {
3437 ATH5K_ERR(ah
->ah_sc
, "gain calibration timeout (%uMHz)\n",
3438 channel
->center_freq
);
3441 /* Restore antenna mode */
3442 ath5k_hw_set_antenna_mode(ah
, ah
->ah_ant_mode
);