drivers/ata/pata_efar.c

   1 /*
   2  *    pata_efar.c - EFAR PIIX clone controller driver
   3  *
   4  *      (C) 2005 Red Hat
   5  *
   6  *    Some parts based on ata_piix.c by Jeff Garzik and others.
   7  *
   8  *    The EFAR is a PIIX4 clone with UDMA66 support. Unlike the later
   9  *    Intel ICH controllers the EFAR widened the UDMA mode register bits
  10  *    and doesn't require the funky clock selection.
  11  */
  12
  13 #include <linux/kernel.h>
  14 #include <linux/module.h>
  15 #include <linux/pci.h>
  16 #include <linux/init.h>
  17 #include <linux/blkdev.h>
  18 #include <linux/delay.h>
  19 #include <linux/device.h>
  20 #include <scsi/scsi_host.h>
  21 #include <linux/libata.h>
  22 #include <linux/ata.h>
  23
  24 #define DRV_NAME        "pata_efar"
  25 #define DRV_VERSION     "0.4.4"
  26
  27 /**
  28  *      efar_pre_reset  -       Enable bits
  29  *      @link: ATA link
  30  *      @deadline: deadline jiffies for the operation
  31  *
  32  *      Perform cable detection for the EFAR ATA interface. This is
  33  *      different to the PIIX arrangement
  34  */
  35
  36 static int efar_pre_reset(struct ata_link *link, unsigned long deadline)
  37 {
  38         static const struct pci_bits efar_enable_bits[] = {
  39                 { 0x41U, 1U, 0x80UL, 0x80UL },  /* port 0 */
  40                 { 0x43U, 1U, 0x80UL, 0x80UL },  /* port 1 */
  41         };
  42         struct ata_port *ap = link->ap;
  43         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  44
  45         if (!pci_test_config_bits(pdev, &efar_enable_bits[ap->port_no]))
  46                 return -ENOENT;
  47
  48         return ata_sff_prereset(link, deadline);
  49 }
  50
  51 /**
  52  *      efar_cable_detect       -       check for 40/80 pin
  53  *      @ap: Port
  54  *
  55  *      Perform cable detection for the EFAR ATA interface. This is
  56  *      different to the PIIX arrangement
  57  */
  58
  59 static int efar_cable_detect(struct ata_port *ap)
  60 {
  61         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  62         u8 tmp;
  63
  64         pci_read_config_byte(pdev, 0x47, &tmp);
  65         if (tmp & (2 >> ap->port_no))
  66                 return ATA_CBL_PATA40;
  67         return ATA_CBL_PATA80;
  68 }
  69
  70 /**
  71  *      efar_set_piomode - Initialize host controller PATA PIO timings
  72  *      @ap: Port whose timings we are configuring
  73  *      @adev: um
  74  *
  75  *      Set PIO mode for device, in host controller PCI config space.
  76  *
  77  *      LOCKING:
  78  *      None (inherited from caller).
  79  */
  80
  81 static void efar_set_piomode (struct ata_port *ap, struct ata_device *adev)
  82 {
  83         unsigned int pio        = adev->pio_mode - XFER_PIO_0;
  84         struct pci_dev *dev     = to_pci_dev(ap->host->dev);
  85         unsigned int idetm_port= ap->port_no ? 0x42 : 0x40;
  86         u16 idetm_data;
  87         int control = 0;
  88
  89         /*
  90          *      See Intel Document 298600-004 for the timing programing rules
  91          *      for PIIX/ICH. The EFAR is a clone so very similar
  92          */
  93
  94         static const     /* ISP  RTC */
  95         u8 timings[][2] = { { 0, 0 },
  96                             { 0, 0 },
  97                             { 1, 0 },
  98                             { 2, 1 },
  99                             { 2, 3 }, };
 100
 101         if (pio > 2)
 102                 control |= 1;   /* TIME1 enable */
 103         if (ata_pio_need_iordy(adev))   /* PIO 3/4 require IORDY */
 104                 control |= 2;   /* IE enable */
 105         /* Intel specifies that the PPE functionality is for disk only */
 106         if (adev->class == ATA_DEV_ATA)
 107                 control |= 4;   /* PPE enable */
 108
 109         pci_read_config_word(dev, idetm_port, &idetm_data);
 110
 111         /* Enable PPE, IE and TIME as appropriate */
 112
 113         if (adev->devno == 0) {
 114                 idetm_data &= 0xCCF0;
 115                 idetm_data |= control;
 116                 idetm_data |= (timings[pio][0] << 12) |
 117                         (timings[pio][1] << 8);
 118         } else {
 119                 int shift = 4 * ap->port_no;
 120                 u8 slave_data;
 121
 122                 idetm_data &= 0xCC0F;
 123                 idetm_data |= (control << 4);
 124
 125                 /* Slave timing in separate register */
 126                 pci_read_config_byte(dev, 0x44, &slave_data);
 127                 slave_data &= 0x0F << shift;
 128                 slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << shift;
 129                 pci_write_config_byte(dev, 0x44, slave_data);
 130         }
 131
 132         idetm_data |= 0x4000;   /* Ensure SITRE is enabled */
 133         pci_write_config_word(dev, idetm_port, idetm_data);
 134 }
 135
 136 /**
 137  *      efar_set_dmamode - Initialize host controller PATA DMA timings
 138  *      @ap: Port whose timings we are configuring
 139  *      @adev: Device to program
 140  *
 141  *      Set UDMA/MWDMA mode for device, in host controller PCI config space.
 142  *
 143  *      LOCKING:
 144  *      None (inherited from caller).
 145  */
 146
 147 static void efar_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 148 {
 149         struct pci_dev *dev     = to_pci_dev(ap->host->dev);
 150         u8 master_port          = ap->port_no ? 0x42 : 0x40;
 151         u16 master_data;
 152         u8 speed                = adev->dma_mode;
 153         int devid               = adev->devno + 2 * ap->port_no;
 154         u8 udma_enable;
 155
 156         static const     /* ISP  RTC */
 157         u8 timings[][2] = { { 0, 0 },
 158                             { 0, 0 },
 159                             { 1, 0 },
 160                             { 2, 1 },
 161                             { 2, 3 }, };
 162
 163         pci_read_config_word(dev, master_port, &master_data);
 164         pci_read_config_byte(dev, 0x48, &udma_enable);
 165
 166         if (speed >= XFER_UDMA_0) {
 167                 unsigned int udma       = adev->dma_mode - XFER_UDMA_0;
 168                 u16 udma_timing;
 169
 170                 udma_enable |= (1 << devid);
 171
 172                 /* Load the UDMA mode number */
 173                 pci_read_config_word(dev, 0x4A, &udma_timing);
 174                 udma_timing &= ~(7 << (4 * devid));
 175                 udma_timing |= udma << (4 * devid);
 176                 pci_write_config_word(dev, 0x4A, udma_timing);
 177         } else {
 178                 /*
 179                  * MWDMA is driven by the PIO timings. We must also enable
 180                  * IORDY unconditionally along with TIME1. PPE has already
 181                  * been set when the PIO timing was set.
 182                  */
 183                 unsigned int mwdma      = adev->dma_mode - XFER_MW_DMA_0;
 184                 unsigned int control;
 185                 u8 slave_data;
 186                 const unsigned int needed_pio[3] = {
 187                         XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
 188                 };
 189                 int pio = needed_pio[mwdma] - XFER_PIO_0;
 190
 191                 control = 3;    /* IORDY|TIME1 */
 192
 193                 /* If the drive MWDMA is faster than it can do PIO then
 194                    we must force PIO into PIO0 */
 195
 196                 if (adev->pio_mode < needed_pio[mwdma])
 197                         /* Enable DMA timing only */
 198                         control |= 8;   /* PIO cycles in PIO0 */
 199
 200                 if (adev->devno) {      /* Slave */
 201                         master_data &= 0xFF4F;  /* Mask out IORDY|TIME1|DMAONLY */
 202                         master_data |= control << 4;
 203                         pci_read_config_byte(dev, 0x44, &slave_data);
 204                         slave_data &= (0x0F + 0xE1 * ap->port_no);
 205                         /* Load the matching timing */
 206                         slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
 207                         pci_write_config_byte(dev, 0x44, slave_data);
 208                 } else {        /* Master */
 209                         master_data &= 0xCCF4;  /* Mask out IORDY|TIME1|DMAONLY
 210                                                    and master timing bits */
 211                         master_data |= control;
 212                         master_data |=
 213                                 (timings[pio][0] << 12) |
 214                                 (timings[pio][1] << 8);
 215                 }
 216                 udma_enable &= ~(1 << devid);
 217                 pci_write_config_word(dev, master_port, master_data);
 218         }
 219         pci_write_config_byte(dev, 0x48, udma_enable);
 220 }
 221
 222 static struct scsi_host_template efar_sht = {
 223         ATA_BMDMA_SHT(DRV_NAME),
 224 };
 225
 226 static struct ata_port_operations efar_ops = {
 227         .inherits               = &ata_bmdma_port_ops,
 228         .cable_detect           = efar_cable_detect,
 229         .set_piomode            = efar_set_piomode,
 230         .set_dmamode            = efar_set_dmamode,
 231         .prereset               = efar_pre_reset,
 232 };
 233
 234
 235 /**
 236  *      efar_init_one - Register EFAR ATA PCI device with kernel services
 237  *      @pdev: PCI device to register
 238  *      @ent: Entry in efar_pci_tbl matching with @pdev
 239  *
 240  *      Called from kernel PCI layer.
 241  *
 242  *      LOCKING:
 243  *      Inherited from PCI layer (may sleep).
 244  *
 245  *      RETURNS:
 246  *      Zero on success, or -ERRNO value.
 247  */
 248
 249 static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 250 {
 251         static int printed_version;
 252         static const struct ata_port_info info = {
 253                 .flags          = ATA_FLAG_SLAVE_POSS,
 254                 .pio_mask       = 0x1f, /* pio0-4 */
 255                 .mwdma_mask     = 0x07, /* mwdma1-2 */
 256                 .udma_mask      = 0x0f, /* UDMA 66 */
 257                 .port_ops       = &efar_ops,
 258         };
 259         const struct ata_port_info *ppi[] = { &info, NULL };
 260
 261         if (!printed_version++)
 262                 dev_printk(KERN_DEBUG, &pdev->dev,
 263                            "version " DRV_VERSION "\n");
 264
 265         return ata_pci_sff_init_one(pdev, ppi, &efar_sht, NULL);
 266 }
 267
 268 static const struct pci_device_id efar_pci_tbl[] = {
 269         { PCI_VDEVICE(EFAR, 0x9130), },
 270
 271         { }     /* terminate list */
 272 };
 273
 274 static struct pci_driver efar_pci_driver = {
 275         .name                   = DRV_NAME,
 276         .id_table               = efar_pci_tbl,
 277         .probe                  = efar_init_one,
 278         .remove                 = ata_pci_remove_one,
 279 #ifdef CONFIG_PM
 280         .suspend                = ata_pci_device_suspend,
 281         .resume                 = ata_pci_device_resume,
 282 #endif
 283 };
 284
 285 static int __init efar_init(void)
 286 {
 287         return pci_register_driver(&efar_pci_driver);
 288 }
 289
 290 static void __exit efar_exit(void)
 291 {
 292         pci_unregister_driver(&efar_pci_driver);
 293 }
 294
 295 module_init(efar_init);
 296 module_exit(efar_exit);
 297
 298 MODULE_AUTHOR("Alan Cox");
 299 MODULE_DESCRIPTION("SCSI low-level driver for EFAR PIIX clones");
 300 MODULE_LICENSE("GPL");
 301 MODULE_DEVICE_TABLE(pci, efar_pci_tbl);
 302 MODULE_VERSION(DRV_VERSION);
 303