sound/oss/aedsp16.c

   1 /*
   2    sound/oss/aedsp16.c
   3
   4    Audio Excel DSP 16 software configuration routines
   5    Copyright (C) 1995,1996,1997,1998  Riccardo Facchetti (fizban@tin.it)
   6
   7    This program is free software; you can redistribute it and/or modify
   8    it under the terms of the GNU General Public License as published by
   9    the Free Software Foundation; either version 2 of the License, or
  10    (at your option) any later version.
  11
  12    This program is distributed in the hope that it will be useful,
  13    but WITHOUT ANY WARRANTY; without even the implied warranty of
  14    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  15    GNU General Public License for more details.
  16
  17    You should have received a copy of the GNU General Public License
  18    along with this program; if not, write to the Free Software
  19    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  20
  21  */
  22 /*
  23  * Include the main OSS Lite header file. It include all the os, OSS Lite, etc
  24  * headers needed by this source.
  25  */
  26 #include <linux/delay.h>
  27 #include <linux/module.h>
  28 #include <linux/init.h>
  29 #include "sound_config.h"
  30
  31 /*
  32
  33    READ THIS
  34
  35    This module started to configure the Audio Excel DSP 16 Sound Card.
  36    Now works with the SC-6000 (old aedsp16) and new SC-6600 based cards.
  37
  38    NOTE: I have NO idea about Audio Excel DSP 16 III. If someone owns this
  39    audio card and want to see the kernel support for it, please contact me.
  40
  41    Audio Excel DSP 16 is an SB pro II, Microsoft Sound System and MPU-401
  42    compatible card.
  43    It is software-only configurable (no jumpers to hard-set irq/dma/mpu-irq),
  44    so before this module, the only way to configure the DSP under linux was
  45    boot the MS-DOS loading the sound.sys device driver (this driver soft-
  46    configure the sound board hardware by massaging someone of its registers),
  47    and then ctrl-alt-del to boot linux with the DSP configured by the DOS
  48    driver.
  49
  50    This module works configuring your Audio Excel DSP 16's irq, dma and
  51    mpu-401-irq. The OSS Lite routines rely on the fact that if the
  52    hardware is there, they can detect it. The problem with AEDSP16 is
  53    that no hardware can be found by the probe routines if the sound card
  54    is not configured properly. Sometimes the kernel probe routines can find
  55    an SBPRO even when the card is not configured (this is the standard setup
  56    of the card), but the SBPRO emulation don't work well if the card is not
  57    properly initialized. For this reason
  58
  59    aedsp16_init_board()
  60
  61    routine is called before the OSS Lite probe routines try to detect the
  62    hardware.
  63
  64    NOTE (READ THE NOTE TOO, IT CONTAIN USEFUL INFORMATIONS)
  65
  66    NOTE: Now it works with SC-6000 and SC-6600 based audio cards. The new cards
  67    have no jumper switch at all. No more WSS or MPU-401 I/O port switches. They
  68    have to be configured by software.
  69
  70    NOTE: The driver is merged with the new OSS Lite sound driver. It works
  71    as a lowlevel driver.
  72
  73    The Audio Excel DSP 16 Sound Card emulates both SBPRO and MSS;
  74    the OSS Lite sound driver can be configured for SBPRO and MSS cards
  75    at the same time, but the aedsp16 can't be two cards!!
  76    When we configure it, we have to choose the SBPRO or the MSS emulation
  77    for AEDSP16. We also can install a *REAL* card of the other type (see [1]).
  78
  79    NOTE: If someone can test the combination AEDSP16+MSS or AEDSP16+SBPRO
  80    please let me know if it works.
  81
  82    The MPU-401 support can be compiled in together with one of the other
  83    two operating modes.
  84
  85    NOTE: This is something like plug-and-play: we have only to plug
  86    the AEDSP16 board in the socket, and then configure and compile
  87    a kernel that uses the AEDSP16 software configuration capability.
  88    No jumper setting is needed!
  89
  90    For example, if you want AEDSP16 to be an SBPro, on irq 10, dma 3
  91    you have just to make config the OSS Lite package, configuring
  92    the AEDSP16 sound card, then activating the SBPro emulation mode
  93    and at last configuring IRQ and DMA.
  94    Compile the kernel and run it.
  95
  96    NOTE: This means for SC-6000 cards that you can choose irq and dma,
  97    but not the I/O addresses. To change I/O addresses you have to set
  98    them with jumpers. For SC-6600 cards you have no jumpers so you have
  99    to set up your full card configuration in the make config.
 100
 101    You can change the irq/dma/mirq settings WITHOUT THE NEED to open
 102    your computer and massage the jumpers (there are no irq/dma/mirq
 103    jumpers to be configured anyway, only I/O BASE values have to be
 104    configured with jumpers)
 105
 106    For some ununderstandable reason, the card default of irq 7, dma 1,
 107    don't work for me. Seems to be an IRQ or DMA conflict. Under heavy
 108    HDD work, the kernel start to erupt out a lot of messages like:
 109
 110    'Sound: DMA timed out - IRQ/DRQ config error?'
 111
 112    For what I can say, I have NOT any conflict at irq 7 (under linux I'm
 113    using the lp polling driver), and dma line 1 is unused as stated by
 114    /proc/dma. I can suppose this is a bug of AEDSP16. I know my hardware so
 115    I'm pretty sure I have not any conflict, but may be I'm wrong. Who knows!
 116    Anyway a setting of irq 10, dma 3 works really fine.
 117
 118    NOTE: if someone can use AEDSP16 with irq 7, dma 1, please let me know
 119    the emulation mode, all the installed hardware and the hardware
 120    configuration (irq and dma settings of all the hardware).
 121
 122    This init module should work with SBPRO+MSS, when one of the two is
 123    the AEDSP16 emulation and the other the real card. (see [1])
 124    For example:
 125
 126    AEDSP16 (0x220) in SBPRO emu (0x220) + real MSS + other
 127    AEDSP16 (0x220) in MSS emu + real SBPRO (0x240) + other
 128
 129    MPU401 should work. (see [2])
 130
 131    [1]
 132        ---
 133        Date: Mon, 29 Jul 1997 08:35:40 +0100
 134        From: Mr S J Greenaway <sjg95@unixfe.rl.ac.uk>
 135
 136        [...]
 137        Just to let you know got my Audio Excel (emulating a MSS) working
 138        with my original SB16, thanks for the driver!
 139        [...]
 140        ---
 141
 142    [2] Not tested by me for lack of hardware.
 143
 144    TODO, WISHES AND TECH
 145
 146    - About I/O ports allocation -
 147
 148    Request the 2x0h region (port base) in any case if we are using this card.
 149
 150    NOTE: the "aedsp16 (base)" string with which we are requesting the aedsp16
 151    port base region (see code) does not mean necessarily that we are emulating
 152    sbpro.  Even if this region is the sbpro I/O ports region, we use this
 153    region to access the control registers of the card, and if emulating
 154    sbpro, I/O sbpro registers too. If we are emulating MSS, the sbpro
 155    registers are not used, in no way, to emulate an sbpro: they are
 156    used only for configuration purposes.
 157
 158    Started Fri Mar 17 16:13:18 MET 1995
 159
 160    v0.1 (ALPHA, was a user-level program called AudioExcelDSP16.c)
 161    - Initial code.
 162    v0.2 (ALPHA)
 163    - Cleanups.
 164    - Integrated with Linux voxware v 2.90-2 kernel sound driver.
 165    - SoundBlaster Pro mode configuration.
 166    - Microsoft Sound System mode configuration.
 167    - MPU-401 mode configuration.
 168    v0.3 (ALPHA)
 169    - Cleanups.
 170    - Rearranged the code to let aedsp16_init_board be more general.
 171    - Erased the REALLY_SLOW_IO. We don't need it. Erased the linux/io.h
 172    inclusion too. We rely on os.h
 173    - Used the  to get a variable
 174    len string (we are not sure about the len of Copyright string).
 175    This works with any SB and compatible.
 176    - Added the code to request_region at device init (should go in
 177    the main body of voxware).
 178    v0.4 (BETA)
 179    - Better configure.c patch for aedsp16 configuration (better
 180    logic of inclusion of AEDSP16 support)
 181    - Modified the conditional compilation to better support more than
 182    one sound card of the emulated type (read the NOTES above)
 183    - Moved the sb init routine from the attach to the very first
 184    probe in sb_card.c
 185    - Rearrangements and cleanups
 186    - Wiped out some unnecessary code and variables: this is kernel
 187    code so it is better save some TEXT and DATA
 188    - Fixed the request_region code. We must allocate the aedsp16 (sbpro)
 189    I/O ports in any case because they are used to access the DSP
 190    configuration registers and we can not allow anyone to get them.
 191    v0.5
 192    - cleanups on comments
 193    - prep for diffs against v3.0-proto-950402
 194    v0.6
 195    - removed the request_region()s when compiling the MODULE sound.o
 196    because we are not allowed (by the actual voxware structure) to
 197    release_region()
 198    v0.7 (pre ALPHA, not distributed)
 199    - started porting this module to kernel 1.3.84. Dummy probe/attach
 200    routines.
 201    v0.8 (ALPHA)
 202    - attached all the init routines.
 203    v0.9 (BETA)
 204    - Integrated with linux-pre2.0.7
 205    - Integrated with configuration scripts.
 206    - Cleaned up and beautyfied the code.
 207    v0.9.9 (BETA)
 208    - Thanks to Piercarlo Grandi: corrected the conditonal compilation code.
 209      Now only the code configured is compiled in, with some memory saving.
 210    v0.9.10
 211    - Integration into the sound/lowlevel/ section of the sound driver.
 212    - Re-organized the code.
 213    v0.9.11 (not distributed)
 214    - Rewritten the init interface-routines to initialize the AEDSP16 in
 215      one shot.
 216    - More cosmetics.
 217    - SC-6600 support.
 218    - More soft/hard configuration.
 219    v0.9.12
 220    - Refined the v0.9.11 code with conditional compilation to distinguish
 221      between SC-6000 and SC-6600 code.
 222    v1.0.0
 223    - Prep for merging with OSS Lite and Linux kernel 2.1.13
 224    - Corrected a bug in request/check/release region calls (thanks to the
 225      new kernel exception handling).
 226    v1.1
 227    - Revamped for integration with new modularized sound drivers: to enhance
 228      the flexibility of modular version, I have removed all the conditional
 229      compilation for SBPRO, MPU and MSS code. Now it is all managed with
 230      the ae_config structure.
 231    v1.2
 232    - Module informations added.
 233    - Removed aedsp16_delay_10msec(), now using mdelay(10)
 234    - All data and funcs moved to .*.init section.
 235    v1.3
 236    Arnaldo Carvalho de Melo <acme@conectiva.com.br> - 2000/09/27
 237    - got rid of check_region
 238
 239    Known Problems:
 240    - Audio Excel DSP 16 III don't work with this driver.
 241
 242    Credits:
 243    Many thanks to Gerald Britton <gbritton@CapAccess.org>. He helped me a
 244    lot in testing the 0.9.11 and 0.9.12 versions of this driver.
 245
 246  */
 247
 248
 249 #define VERSION "1.3"           /* Version of Audio Excel DSP 16 driver */
 250
 251 #undef  AEDSP16_DEBUG           /* Define this to 1 to enable debug code     */
 252 #undef  AEDSP16_DEBUG_MORE      /* Define this to 1 to enable more debug     */
 253 #undef  AEDSP16_INFO            /* Define this to 1 to enable info code      */
 254
 255 #if defined(AEDSP16_DEBUG)
 256 # define DBG(x)  printk x
 257 # if defined(AEDSP16_DEBUG_MORE)
 258 #  define DBG1(x) printk x
 259 # else
 260 #  define DBG1(x)
 261 # endif
 262 #else
 263 # define DBG(x)
 264 # define DBG1(x)
 265 #endif
 266
 267 /*
 268  * Misc definitions
 269  */
 270 #define TRUE    1
 271 #define FALSE   0
 272
 273 /*
 274  * Region Size for request/check/release region.
 275  */
 276 #define IOBASE_REGION_SIZE      0x10
 277
 278 /*
 279  * Hardware related defaults
 280  */
 281 #define DEF_AEDSP16_IOB 0x220   /* 0x220(default) 0x240                 */
 282 #define DEF_AEDSP16_IRQ 7       /* 5 7(default) 9 10 11                 */
 283 #define DEF_AEDSP16_MRQ 0       /* 5 7 9 10 0(default), 0 means disable */
 284 #define DEF_AEDSP16_DMA 1       /* 0 1(default) 3                       */
 285
 286 /*
 287  * Commands of AEDSP16's DSP (SBPRO+special).
 288  * Some of them are COMMAND_xx, in the future they may change.
 289  */
 290 #define WRITE_MDIRQ_CFG   0x50  /* Set M&I&DRQ mask (the real config)   */
 291 #define COMMAND_52        0x52  /*                                      */
 292 #define READ_HARD_CFG     0x58  /* Read Hardware Config (I/O base etc)  */
 293 #define COMMAND_5C        0x5c  /*                                      */
 294 #define COMMAND_60        0x60  /*                                      */
 295 #define COMMAND_66        0x66  /*                                      */
 296 #define COMMAND_6C        0x6c  /*                                      */
 297 #define COMMAND_6E        0x6e  /*                                      */
 298 #define COMMAND_88        0x88  /*                                      */
 299 #define DSP_INIT_MSS      0x8c  /* Enable Microsoft Sound System mode   */
 300 #define COMMAND_C5        0xc5  /*                                      */
 301 #define GET_DSP_VERSION   0xe1  /* Get DSP Version                      */
 302 #define GET_DSP_COPYRIGHT 0xe3  /* Get DSP Copyright                    */
 303
 304 /*
 305  * Offsets of AEDSP16 DSP I/O ports. The offset is added to base I/O port
 306  * to have the actual I/O port.
 307  * Register permissions are:
 308  * (wo) == Write Only
 309  * (ro) == Read  Only
 310  * (w-) == Write
 311  * (r-) == Read
 312  */
 313 #define DSP_RESET    0x06       /* offset of DSP RESET             (wo) */
 314 #define DSP_READ     0x0a       /* offset of DSP READ              (ro) */
 315 #define DSP_WRITE    0x0c       /* offset of DSP WRITE             (w-) */
 316 #define DSP_COMMAND  0x0c       /* offset of DSP COMMAND           (w-) */
 317 #define DSP_STATUS   0x0c       /* offset of DSP STATUS            (r-) */
 318 #define DSP_DATAVAIL 0x0e       /* offset of DSP DATA AVAILABLE    (ro) */
 319
 320
 321 #define RETRY           10      /* Various retry values on I/O opera-   */
 322 #define STATUSRETRY   1000      /* tions. Sometimes we have to          */
 323 #define HARDRETRY   500000      /* wait for previous cmd to complete    */
 324
 325 /*
 326  * Size of character arrays that store name and version of sound card
 327  */
 328 #define CARDNAMELEN 15          /* Size of the card's name in chars     */
 329 #define CARDVERLEN  2           /* Size of the card's version in chars  */
 330
 331 #if defined(CONFIG_SC6600)
 332 /*
 333  * Bitmapped flags of hard configuration
 334  */
 335 /*
 336  * Decode macros (xl == low byte, xh = high byte)
 337  */
 338 #define IOBASE(xl)              ((xl & 0x01)?0x240:0x220)
 339 #define JOY(xl)                 (xl & 0x02)
 340 #define MPUADDR(xl)             (                       \
 341                                 (xl & 0x0C)?0x330:      \
 342                                 (xl & 0x08)?0x320:      \
 343                                 (xl & 0x04)?0x310:      \
 344                                                 0x300)
 345 #define WSSADDR(xl)             ((xl & 0x10)?0xE80:0x530)
 346 #define CDROM(xh)               (xh & 0x20)
 347 #define CDROMADDR(xh)           (((xh & 0x1F) << 4) + 0x200)
 348 /*
 349  * Encode macros
 350  */
 351 #define BLDIOBASE(xl, val) {            \
 352         xl &= ~0x01;                    \
 353         if (val == 0x240)               \
 354                 xl |= 0x01;             \
 355         }
 356 #define BLDJOY(xl, val) {               \
 357         xl &= ~0x02;                    \
 358         if (val == 1)                   \
 359                 xl |= 0x02;             \
 360         }
 361 #define BLDMPUADDR(xl, val) {           \
 362         xl &= ~0x0C;                    \
 363         switch (val) {                  \
 364                 case 0x330:             \
 365                         xl |= 0x0C;     \
 366                         break;          \
 367                 case 0x320:             \
 368                         xl |= 0x08;     \
 369                         break;          \
 370                 case 0x310:             \
 371                         xl |= 0x04;     \
 372                         break;          \
 373                 case 0x300:             \
 374                         xl |= 0x00;     \
 375                         break;          \
 376                 default:                \
 377                         xl |= 0x00;     \
 378                         break;          \
 379                 }                       \
 380         }
 381 #define BLDWSSADDR(xl, val) {           \
 382         xl &= ~0x10;                    \
 383         if (val == 0xE80)               \
 384                 xl |= 0x10;             \
 385         }
 386 #define BLDCDROM(xh, val) {             \
 387         xh &= ~0x20;                    \
 388         if (val == 1)                   \
 389                 xh |= 0x20;             \
 390         }
 391 #define BLDCDROMADDR(xh, val) {         \
 392         int tmp = val;                  \
 393         tmp -= 0x200;                   \
 394         tmp >>= 4;                      \
 395         tmp &= 0x1F;                    \
 396         xh |= tmp;                      \
 397         xh &= 0x7F;                     \
 398         xh |= 0x40;                     \
 399         }
 400 #endif /* CONFIG_SC6600 */
 401
 402 /*
 403  * Bit mapped flags for calling aedsp16_init_board(), and saving the current
 404  * emulation mode.
 405  */
 406 #define INIT_NONE   (0   )
 407 #define INIT_SBPRO  (1<<0)
 408 #define INIT_MSS    (1<<1)
 409 #define INIT_MPU401 (1<<2)
 410
 411 static int      soft_cfg __initdata = 0;        /* bitmapped config */
 412 static int      soft_cfg_mss __initdata = 0;    /* bitmapped mss config */
 413 static int      ver[CARDVERLEN] __initdata = {0, 0};    /* DSP Ver:
 414                                                    hi->ver[0] lo->ver[1] */
 415
 416 #if defined(CONFIG_SC6600)
 417 static int      hard_cfg[2]     /* lo<-hard_cfg[0] hi<-hard_cfg[1]      */
 418                      __initdata = { 0, 0};
 419 #endif /* CONFIG_SC6600 */
 420
 421 #if defined(CONFIG_SC6600)
 422 /* Decoded hard configuration */
 423 struct  d_hcfg {
 424         int iobase;
 425         int joystick;
 426         int mpubase;
 427         int wssbase;
 428         int cdrom;
 429         int cdrombase;
 430 };
 431
 432 static struct d_hcfg decoded_hcfg __initdata = {0, };
 433
 434 #endif /* CONFIG_SC6600 */
 435
 436 /* orVals contain the values to be or'ed                                */
 437 struct orVals {
 438         int     val;            /* irq|mirq|dma                         */
 439         int     or;             /* soft_cfg |= TheStruct.or             */
 440 };
 441
 442 /* aedsp16_info contain the audio card configuration                  */
 443 struct aedsp16_info {
 444         int base_io;            /* base I/O address for accessing card  */
 445         int irq;                /* irq value for DSP I/O                */
 446         int mpu_irq;            /* irq for mpu401 interface I/O         */
 447         int dma;                /* dma value for DSP I/O                */
 448         int mss_base;           /* base I/O for Microsoft Sound System  */
 449         int mpu_base;           /* base I/O for MPU-401 emulation       */
 450         int init;               /* Initialization status of the card    */
 451 };
 452
 453 /*
 454  * Magic values that the DSP will eat when configuring irq/mirq/dma
 455  */
 456 /* DSP IRQ conversion array             */
 457 static struct orVals orIRQ[] __initdata = {
 458         {0x05, 0x28},
 459         {0x07, 0x08},
 460         {0x09, 0x10},
 461         {0x0a, 0x18},
 462         {0x0b, 0x20},
 463         {0x00, 0x00}
 464 };
 465
 466 /* MPU-401 IRQ conversion array         */
 467 static struct orVals orMIRQ[] __initdata = {
 468         {0x05, 0x04},
 469         {0x07, 0x44},
 470         {0x09, 0x84},
 471         {0x0a, 0xc4},
 472         {0x00, 0x00}
 473 };
 474
 475 /* DMA Channels conversion array        */
 476 static struct orVals orDMA[] __initdata = {
 477         {0x00, 0x01},
 478         {0x01, 0x02},
 479         {0x03, 0x03},
 480         {0x00, 0x00}
 481 };
 482
 483 static struct aedsp16_info ae_config = {
 484         DEF_AEDSP16_IOB,
 485         DEF_AEDSP16_IRQ,
 486         DEF_AEDSP16_MRQ,
 487         DEF_AEDSP16_DMA,
 488         -1,
 489         -1,
 490         INIT_NONE
 491 };
 492
 493 /*
 494  * Buffers to store audio card informations
 495  */
 496 static char     DSPCopyright[CARDNAMELEN + 1] __initdata = {0, };
 497 static char     DSPVersion[CARDVERLEN + 1] __initdata = {0, };
 498
 499 static int __init aedsp16_wait_data(int port)
 500 {
 501         int             loop = STATUSRETRY;
 502         unsigned char   ret = 0;
 503
 504         DBG1(("aedsp16_wait_data (0x%x): ", port));
 505
 506         do {
 507                   ret = inb(port + DSP_DATAVAIL);
 508         /*
 509          * Wait for data available (bit 7 of ret == 1)
 510          */
 511           } while (!(ret & 0x80) && loop--);
 512
 513         if (ret & 0x80) {
 514                 DBG1(("success.\n"));
 515                 return TRUE;
 516         }
 517
 518         DBG1(("failure.\n"));
 519         return FALSE;
 520 }
 521
 522 static int __init aedsp16_read(int port)
 523 {
 524         int inbyte;
 525
 526         DBG(("    Read DSP Byte (0x%x): ", port));
 527
 528         if (aedsp16_wait_data(port) == FALSE) {
 529                 DBG(("failure.\n"));
 530                 return -1;
 531         }
 532
 533         inbyte = inb(port + DSP_READ);
 534
 535         DBG(("read [0x%x]/{%c}.\n", inbyte, inbyte));
 536
 537         return inbyte;
 538 }
 539
 540 static int __init aedsp16_test_dsp(int port)
 541 {
 542         return ((aedsp16_read(port) == 0xaa) ? TRUE : FALSE);
 543 }
 544
 545 static int __init aedsp16_dsp_reset(int port)
 546 {
 547         /*
 548          * Reset DSP
 549          */
 550
 551         DBG(("Reset DSP:\n"));
 552
 553         outb(1, (port + DSP_RESET));
 554         udelay(10);
 555         outb(0, (port + DSP_RESET));
 556         udelay(10);
 557         udelay(10);
 558         if (aedsp16_test_dsp(port) == TRUE) {
 559                 DBG(("success.\n"));
 560                 return TRUE;
 561         } else
 562                 DBG(("failure.\n"));
 563         return FALSE;
 564 }
 565
 566 static int __init aedsp16_write(int port, int cmd)
 567 {
 568         unsigned char   ret;
 569         int             loop = HARDRETRY;
 570
 571         DBG(("    Write DSP Byte (0x%x) [0x%x]: ", port, cmd));
 572
 573         do {
 574                 ret = inb(port + DSP_STATUS);
 575                 /*
 576                  * DSP ready to receive data if bit 7 of ret == 0
 577                  */
 578                 if (!(ret & 0x80)) {
 579                         outb(cmd, port + DSP_COMMAND);
 580                         DBG(("success.\n"));
 581                         return 0;
 582                 }
 583         } while (loop--);
 584
 585         DBG(("timeout.\n"));
 586         printk("[AEDSP16] DSP Command (0x%x) timeout.\n", cmd);
 587
 588         return -1;
 589 }
 590
 591 #if defined(CONFIG_SC6600)
 592
 593 #if defined(AEDSP16_INFO) || defined(AEDSP16_DEBUG)
 594 void __init aedsp16_pinfo(void) {
 595         DBG(("\n Base address:  %x\n", decoded_hcfg.iobase));
 596         DBG((" Joystick    : %s present\n", decoded_hcfg.joystick?"":" not"));
 597         DBG((" WSS addr    :  %x\n", decoded_hcfg.wssbase));
 598         DBG((" MPU-401 addr:  %x\n", decoded_hcfg.mpubase));
 599         DBG((" CDROM       : %s present\n", (decoded_hcfg.cdrom!=4)?"":" not"));
 600         DBG((" CDROMADDR   :  %x\n\n", decoded_hcfg.cdrombase));
 601 }
 602 #endif
 603
 604 static void __init aedsp16_hard_decode(void) {
 605
 606         DBG((" aedsp16_hard_decode: 0x%x, 0x%x\n", hard_cfg[0], hard_cfg[1]));
 607
 608 /*
 609  * Decode Cfg Bytes.
 610  */
 611         decoded_hcfg.iobase     = IOBASE(hard_cfg[0]);
 612         decoded_hcfg.joystick   = JOY(hard_cfg[0]);
 613         decoded_hcfg.wssbase    = WSSADDR(hard_cfg[0]);
 614         decoded_hcfg.mpubase    = MPUADDR(hard_cfg[0]);
 615         decoded_hcfg.cdrom      = CDROM(hard_cfg[1]);
 616         decoded_hcfg.cdrombase  = CDROMADDR(hard_cfg[1]);
 617
 618 #if defined(AEDSP16_INFO) || defined(AEDSP16_DEBUG)
 619         printk(" Original sound card configuration:\n");
 620         aedsp16_pinfo();
 621 #endif
 622
 623 /*
 624  * Now set up the real kernel configuration.
 625  */
 626         decoded_hcfg.iobase     = ae_config.base_io;
 627         decoded_hcfg.wssbase    = ae_config.mss_base;
 628         decoded_hcfg.mpubase    = ae_config.mpu_base;
 629
 630 #if defined(CONFIG_SC6600_JOY)
 631         decoded_hcfg.joystick   = CONFIG_SC6600_JOY; /* Enable */
 632 #endif
 633 #if defined(CONFIG_SC6600_CDROM)
 634         decoded_hcfg.cdrom      = CONFIG_SC6600_CDROM; /* 4:N-3:I-2:G-1:P-0:S */
 635 #endif
 636 #if defined(CONFIG_SC6600_CDROMBASE)
 637         decoded_hcfg.cdrombase  = CONFIG_SC6600_CDROMBASE; /* 0 Disable */
 638 #endif
 639
 640 #if defined(AEDSP16_DEBUG)
 641         DBG((" New Values:\n"));
 642         aedsp16_pinfo();
 643 #endif
 644
 645         DBG(("success.\n"));
 646 }
 647
 648 static void __init aedsp16_hard_encode(void) {
 649
 650         DBG((" aedsp16_hard_encode: 0x%x, 0x%x\n", hard_cfg[0], hard_cfg[1]));
 651
 652         hard_cfg[0] = 0;
 653         hard_cfg[1] = 0;
 654
 655         hard_cfg[0] |= 0x20;
 656
 657         BLDIOBASE (hard_cfg[0], decoded_hcfg.iobase);
 658         BLDWSSADDR(hard_cfg[0], decoded_hcfg.wssbase);
 659         BLDMPUADDR(hard_cfg[0], decoded_hcfg.mpubase);
 660         BLDJOY(hard_cfg[0], decoded_hcfg.joystick);
 661         BLDCDROM(hard_cfg[1], decoded_hcfg.cdrom);
 662         BLDCDROMADDR(hard_cfg[1], decoded_hcfg.cdrombase);
 663
 664 #if defined(AEDSP16_DEBUG)
 665         aedsp16_pinfo();
 666 #endif
 667
 668         DBG((" aedsp16_hard_encode: 0x%x, 0x%x\n", hard_cfg[0], hard_cfg[1]));
 669         DBG(("success.\n"));
 670
 671 }
 672
 673 static int __init aedsp16_hard_write(int port) {
 674
 675         DBG(("aedsp16_hard_write:\n"));
 676
 677         if (aedsp16_write(port, COMMAND_6C)) {
 678                 printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_6C);
 679                 DBG(("failure.\n"));
 680                 return FALSE;
 681         }
 682         if (aedsp16_write(port, COMMAND_5C)) {
 683                 printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_5C);
 684                 DBG(("failure.\n"));
 685                 return FALSE;
 686         }
 687         if (aedsp16_write(port, hard_cfg[0])) {
 688                 printk("[AEDSP16] DATA 0x%x: failed!\n", hard_cfg[0]);
 689                 DBG(("failure.\n"));
 690                 return FALSE;
 691         }
 692         if (aedsp16_write(port, hard_cfg[1])) {
 693                 printk("[AEDSP16] DATA 0x%x: failed!\n", hard_cfg[1]);
 694                 DBG(("failure.\n"));
 695                 return FALSE;
 696         }
 697         if (aedsp16_write(port, COMMAND_C5)) {
 698                 printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_C5);
 699                 DBG(("failure.\n"));
 700                 return FALSE;
 701         }
 702
 703         DBG(("success.\n"));
 704
 705         return TRUE;
 706 }
 707
 708 static int __init aedsp16_hard_read(int port) {
 709
 710         DBG(("aedsp16_hard_read:\n"));
 711
 712         if (aedsp16_write(port, READ_HARD_CFG)) {
 713                 printk("[AEDSP16] CMD 0x%x: failed!\n", READ_HARD_CFG);
 714                 DBG(("failure.\n"));
 715                 return FALSE;
 716         }
 717
 718         if ((hard_cfg[0] = aedsp16_read(port)) == -1) {
 719                 printk("[AEDSP16] aedsp16_read after CMD 0x%x: failed\n",
 720                         READ_HARD_CFG);
 721                 DBG(("failure.\n"));
 722                 return FALSE;
 723         }
 724         if ((hard_cfg[1] = aedsp16_read(port)) == -1) {
 725                 printk("[AEDSP16] aedsp16_read after CMD 0x%x: failed\n",
 726                         READ_HARD_CFG);
 727                 DBG(("failure.\n"));
 728                 return FALSE;
 729         }
 730         if (aedsp16_read(port) == -1) {
 731                 printk("[AEDSP16] aedsp16_read after CMD 0x%x: failed\n",
 732                         READ_HARD_CFG);
 733                 DBG(("failure.\n"));
 734                 return FALSE;
 735         }
 736
 737         DBG(("success.\n"));
 738
 739         return TRUE;
 740 }
 741
 742 static int __init aedsp16_ext_cfg_write(int port) {
 743
 744         int extcfg, val;
 745
 746         if (aedsp16_write(port, COMMAND_66)) {
 747                 printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_66);
 748                 return FALSE;
 749         }
 750
 751         extcfg = 7;
 752         if (decoded_hcfg.cdrom != 2)
 753                 extcfg = 0x0F;
 754         if ((decoded_hcfg.cdrom == 4) ||
 755             (decoded_hcfg.cdrom == 3))
 756                 extcfg &= ~2;
 757         if (decoded_hcfg.cdrombase == 0)
 758                 extcfg &= ~2;
 759         if (decoded_hcfg.mpubase == 0)
 760                 extcfg &= ~1;
 761
 762         if (aedsp16_write(port, extcfg)) {
 763                 printk("[AEDSP16] Write extcfg: failed!\n");
 764                 return FALSE;
 765         }
 766         if (aedsp16_write(port, 0)) {
 767                 printk("[AEDSP16] Write extcfg: failed!\n");
 768                 return FALSE;
 769         }
 770         if (decoded_hcfg.cdrom == 3) {
 771                 if (aedsp16_write(port, COMMAND_52)) {
 772                         printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_52);
 773                         return FALSE;
 774                 }
 775                 if ((val = aedsp16_read(port)) == -1) {
 776                         printk("[AEDSP16] aedsp16_read after CMD 0x%x: failed\n"
 777                                         , COMMAND_52);
 778                         return FALSE;
 779                 }
 780                 val &= 0x7F;
 781                 if (aedsp16_write(port, COMMAND_60)) {
 782                         printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_60);
 783                         return FALSE;
 784                 }
 785                 if (aedsp16_write(port, val)) {
 786                         printk("[AEDSP16] Write val: failed!\n");
 787                         return FALSE;
 788                 }
 789         }
 790
 791         return TRUE;
 792 }
 793
 794 #endif /* CONFIG_SC6600 */
 795
 796 static int __init aedsp16_cfg_write(int port) {
 797         if (aedsp16_write(port, WRITE_MDIRQ_CFG)) {
 798                 printk("[AEDSP16] CMD 0x%x: failed!\n", WRITE_MDIRQ_CFG);
 799                 return FALSE;
 800         }
 801         if (aedsp16_write(port, soft_cfg)) {
 802                 printk("[AEDSP16] Initialization of (M)IRQ and DMA: failed!\n");
 803                 return FALSE;
 804         }
 805         return TRUE;
 806 }
 807
 808 static int __init aedsp16_init_mss(int port)
 809 {
 810         DBG(("aedsp16_init_mss:\n"));
 811
 812         mdelay(10);
 813
 814         if (aedsp16_write(port, DSP_INIT_MSS)) {
 815                 printk("[AEDSP16] aedsp16_init_mss [0x%x]: failed!\n",
 816                                 DSP_INIT_MSS);
 817                 DBG(("failure.\n"));
 818                 return FALSE;
 819         }
 820
 821         mdelay(10);
 822
 823         if (aedsp16_cfg_write(port) == FALSE)
 824                 return FALSE;
 825
 826         outb(soft_cfg_mss, ae_config.mss_base);
 827
 828         DBG(("success.\n"));
 829
 830         return TRUE;
 831 }
 832
 833 static int __init aedsp16_setup_board(int port) {
 834         int     loop = RETRY;
 835
 836 #if defined(CONFIG_SC6600)
 837         int     val = 0;
 838
 839         if (aedsp16_hard_read(port) == FALSE) {
 840                 printk("[AEDSP16] aedsp16_hard_read: failed!\n");
 841                 return FALSE;
 842         }
 843
 844         if (aedsp16_write(port, COMMAND_52)) {
 845                 printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_52);
 846                 return FALSE;
 847         }
 848
 849         if ((val = aedsp16_read(port)) == -1) {
 850                 printk("[AEDSP16] aedsp16_read after CMD 0x%x: failed\n",
 851                                 COMMAND_52);
 852                 return FALSE;
 853         }
 854 #endif
 855
 856         do {
 857                 if (aedsp16_write(port, COMMAND_88)) {
 858                         printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_88);
 859                         return FALSE;
 860                 }
 861                 mdelay(10);
 862         } while ((aedsp16_wait_data(port) == FALSE) && loop--);
 863
 864         if (aedsp16_read(port) == -1) {
 865                 printk("[AEDSP16] aedsp16_read after CMD 0x%x: failed\n",
 866                                 COMMAND_88);
 867                 return FALSE;
 868         }
 869
 870 #if !defined(CONFIG_SC6600)
 871         if (aedsp16_write(port, COMMAND_5C)) {
 872                 printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_5C);
 873                 return FALSE;
 874         }
 875 #endif
 876
 877         if (aedsp16_cfg_write(port) == FALSE)
 878                 return FALSE;
 879
 880 #if defined(CONFIG_SC6600)
 881         if (aedsp16_write(port, COMMAND_60)) {
 882                 printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_60);
 883                 return FALSE;
 884         }
 885         if (aedsp16_write(port, val)) {
 886                 printk("[AEDSP16] DATA 0x%x: failed!\n", val);
 887                 return FALSE;
 888         }
 889         if (aedsp16_write(port, COMMAND_6E)) {
 890                 printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_6E);
 891                 return FALSE;
 892         }
 893         if (aedsp16_write(port, ver[0])) {
 894                 printk("[AEDSP16] DATA 0x%x: failed!\n", ver[0]);
 895                 return FALSE;
 896         }
 897         if (aedsp16_write(port, ver[1])) {
 898                 printk("[AEDSP16] DATA 0x%x: failed!\n", ver[1]);
 899                 return FALSE;
 900         }
 901
 902         if (aedsp16_hard_write(port) == FALSE) {
 903                 printk("[AEDSP16] aedsp16_hard_write: failed!\n");
 904                 return FALSE;
 905         }
 906
 907         if (aedsp16_write(port, COMMAND_5C)) {
 908                 printk("[AEDSP16] CMD 0x%x: failed!\n", COMMAND_5C);
 909                 return FALSE;
 910         }
 911
 912 #if defined(THIS_IS_A_THING_I_HAVE_NOT_TESTED_YET)
 913         if (aedsp16_cfg_write(port) == FALSE)
 914                 return FALSE;
 915 #endif
 916
 917 #endif
 918
 919         return TRUE;
 920 }
 921
 922 static int __init aedsp16_stdcfg(int port) {
 923         if (aedsp16_write(port, WRITE_MDIRQ_CFG)) {
 924                 printk("[AEDSP16] CMD 0x%x: failed!\n", WRITE_MDIRQ_CFG);
 925                 return FALSE;
 926         }
 927         /*
 928          * 0x0A == (IRQ 7, DMA 1, MIRQ 0)
 929          */
 930         if (aedsp16_write(port, 0x0A)) {
 931                 printk("[AEDSP16] aedsp16_stdcfg: failed!\n");
 932                 return FALSE;
 933         }
 934         return TRUE;
 935 }
 936
 937 static int __init aedsp16_dsp_version(int port)
 938 {
 939         int             len = 0;
 940         int             ret;
 941
 942         DBG(("Get DSP Version:\n"));
 943
 944         if (aedsp16_write(ae_config.base_io, GET_DSP_VERSION)) {
 945                 printk("[AEDSP16] CMD 0x%x: failed!\n", GET_DSP_VERSION);
 946                 DBG(("failed.\n"));
 947                 return FALSE;
 948         }
 949
 950         do {
 951                 if ((ret = aedsp16_read(port)) == -1) {
 952                         DBG(("failed.\n"));
 953                         return FALSE;
 954                 }
 955         /*
 956          * We already know how many int are stored (2), so we know when the
 957          * string is finished.
 958          */
 959                 ver[len++] = ret;
 960           } while (len < CARDVERLEN);
 961         sprintf(DSPVersion, "%d.%d", ver[0], ver[1]);
 962
 963         DBG(("success.\n"));
 964
 965         return TRUE;
 966 }
 967
 968 static int __init aedsp16_dsp_copyright(int port)
 969 {
 970         int             len = 0;
 971         int             ret;
 972
 973         DBG(("Get DSP Copyright:\n"));
 974
 975         if (aedsp16_write(ae_config.base_io, GET_DSP_COPYRIGHT)) {
 976                 printk("[AEDSP16] CMD 0x%x: failed!\n", GET_DSP_COPYRIGHT);
 977                 DBG(("failed.\n"));
 978                 return FALSE;
 979         }
 980
 981         do {
 982                 if ((ret = aedsp16_read(port)) == -1) {
 983         /*
 984          * If no more data available, return to the caller, no error if len>0.
 985          * We have no other way to know when the string is finished.
 986          */
 987                         if (len)
 988                                 break;
 989                         else {
 990                                 DBG(("failed.\n"));
 991                                 return FALSE;
 992                         }
 993                 }
 994
 995                 DSPCopyright[len++] = ret;
 996
 997           } while (len < CARDNAMELEN);
 998
 999         DBG(("success.\n"));
1000
1001         return TRUE;
1002 }
1003
1004 static void __init aedsp16_init_tables(void)
1005 {
1006         int i = 0;
1007
1008         memset(DSPCopyright, 0, CARDNAMELEN + 1);
1009         memset(DSPVersion, 0, CARDVERLEN + 1);
1010
1011         for (i = 0; orIRQ[i].or; i++)
1012                 if (orIRQ[i].val == ae_config.irq) {
1013                         soft_cfg |= orIRQ[i].or;
1014                         soft_cfg_mss |= orIRQ[i].or;
1015                 }
1016
1017         for (i = 0; orMIRQ[i].or; i++)
1018                 if (orMIRQ[i].or == ae_config.mpu_irq)
1019                         soft_cfg |= orMIRQ[i].or;
1020
1021         for (i = 0; orDMA[i].or; i++)
1022                 if (orDMA[i].val == ae_config.dma) {
1023                         soft_cfg |= orDMA[i].or;
1024                         soft_cfg_mss |= orDMA[i].or;
1025                 }
1026 }
1027
1028 static int __init aedsp16_init_board(void)
1029 {
1030         aedsp16_init_tables();
1031
1032         if (aedsp16_dsp_reset(ae_config.base_io) == FALSE) {
1033                 printk("[AEDSP16] aedsp16_dsp_reset: failed!\n");
1034                 return FALSE;
1035         }
1036         if (aedsp16_dsp_copyright(ae_config.base_io) == FALSE) {
1037                 printk("[AEDSP16] aedsp16_dsp_copyright: failed!\n");
1038                 return FALSE;
1039         }
1040
1041         /*
1042          * My AEDSP16 card return SC-6000 in DSPCopyright, so
1043          * if we have something different, we have to be warned.
1044          */
1045         if (strcmp("SC-6000", DSPCopyright))
1046                 printk("[AEDSP16] Warning: non SC-6000 audio card!\n");
1047
1048         if (aedsp16_dsp_version(ae_config.base_io) == FALSE) {
1049                 printk("[AEDSP16] aedsp16_dsp_version: failed!\n");
1050                 return FALSE;
1051         }
1052
1053         if (aedsp16_stdcfg(ae_config.base_io) == FALSE) {
1054                 printk("[AEDSP16] aedsp16_stdcfg: failed!\n");
1055                 return FALSE;
1056         }
1057
1058 #if defined(CONFIG_SC6600)
1059         if (aedsp16_hard_read(ae_config.base_io) == FALSE) {
1060                 printk("[AEDSP16] aedsp16_hard_read: failed!\n");
1061                 return FALSE;
1062         }
1063
1064         aedsp16_hard_decode();
1065
1066         aedsp16_hard_encode();
1067
1068         if (aedsp16_hard_write(ae_config.base_io) == FALSE) {
1069                 printk("[AEDSP16] aedsp16_hard_write: failed!\n");
1070                 return FALSE;
1071         }
1072
1073         if (aedsp16_ext_cfg_write(ae_config.base_io) == FALSE) {
1074                 printk("[AEDSP16] aedsp16_ext_cfg_write: failed!\n");
1075                 return FALSE;
1076         }
1077 #endif /* CONFIG_SC6600 */
1078
1079         if (aedsp16_setup_board(ae_config.base_io) == FALSE) {
1080                 printk("[AEDSP16] aedsp16_setup_board: failed!\n");
1081                 return FALSE;
1082         }
1083
1084         if (ae_config.mss_base != -1) {
1085                 if (ae_config.init & INIT_MSS) {
1086                         if (aedsp16_init_mss(ae_config.base_io) == FALSE) {
1087                                 printk("[AEDSP16] Can not initialize"
1088                                        "Microsoft Sound System mode.\n");
1089                                 return FALSE;
1090                         }
1091                 }
1092         }
1093
1094 #if !defined(MODULE) || defined(AEDSP16_INFO) || defined(AEDSP16_DEBUG)
1095
1096         printk("Audio Excel DSP 16 init v%s (%s %s) [",
1097                 VERSION, DSPCopyright,
1098                 DSPVersion);
1099
1100         if (ae_config.mpu_base != -1) {
1101                 if (ae_config.init & INIT_MPU401) {
1102                         printk("MPU401");
1103                         if ((ae_config.init & INIT_MSS) ||
1104                             (ae_config.init & INIT_SBPRO))
1105                                 printk(" ");
1106                 }
1107         }
1108
1109         if (ae_config.mss_base == -1) {
1110                 if (ae_config.init & INIT_SBPRO) {
1111                         printk("SBPro");
1112                         if (ae_config.init & INIT_MSS)
1113                                 printk(" ");
1114                 }
1115         }
1116
1117         if (ae_config.mss_base != -1)
1118                 if (ae_config.init & INIT_MSS)
1119                         printk("MSS");
1120
1121         printk("]\n");
1122 #endif /* MODULE || AEDSP16_INFO || AEDSP16_DEBUG */
1123
1124         mdelay(10);
1125
1126         return TRUE;
1127 }
1128
1129 static int __init init_aedsp16_sb(void)
1130 {
1131         DBG(("init_aedsp16_sb: "));
1132
1133 /*
1134  * If the card is already init'ed MSS, we can not init it to SBPRO too
1135  * because the board can not emulate simultaneously MSS and SBPRO.
1136  */
1137         if (ae_config.init & INIT_MSS)
1138                 return FALSE;
1139         if (ae_config.init & INIT_SBPRO)
1140                 return FALSE;
1141
1142         ae_config.init |= INIT_SBPRO;
1143
1144         DBG(("done.\n"));
1145
1146         return TRUE;
1147 }
1148
1149 static void uninit_aedsp16_sb(void)
1150 {
1151         DBG(("uninit_aedsp16_sb: "));
1152
1153         ae_config.init &= ~INIT_SBPRO;
1154
1155         DBG(("done.\n"));
1156 }
1157
1158 static int __init init_aedsp16_mss(void)
1159 {
1160         DBG(("init_aedsp16_mss: "));
1161
1162 /*
1163  * If the card is already init'ed SBPRO, we can not init it to MSS too
1164  * because the board can not emulate simultaneously MSS and SBPRO.
1165  */
1166         if (ae_config.init & INIT_SBPRO)
1167                 return FALSE;
1168         if (ae_config.init & INIT_MSS)
1169                 return FALSE;
1170 /*
1171  * We must allocate the CONFIG_AEDSP16_BASE region too because these are the
1172  * I/O ports to access card's control registers.
1173  */
1174         if (!(ae_config.init & INIT_MPU401)) {
1175                 if (!request_region(ae_config.base_io, IOBASE_REGION_SIZE,
1176                                 "aedsp16 (base)")) {
1177                         printk(
1178                         "AEDSP16 BASE I/O port region is already in use.\n");
1179                         return FALSE;
1180                 }
1181         }
1182
1183         ae_config.init |= INIT_MSS;
1184
1185         DBG(("done.\n"));
1186
1187         return TRUE;
1188 }
1189
1190 static void uninit_aedsp16_mss(void)
1191 {
1192         DBG(("uninit_aedsp16_mss: "));
1193
1194         if ((!(ae_config.init & INIT_MPU401)) &&
1195            (ae_config.init & INIT_MSS)) {
1196                 release_region(ae_config.base_io, IOBASE_REGION_SIZE);
1197                 DBG(("AEDSP16 base region released.\n"));
1198         }
1199
1200         ae_config.init &= ~INIT_MSS;
1201         DBG(("done.\n"));
1202 }
1203
1204 static int __init init_aedsp16_mpu(void)
1205 {
1206         DBG(("init_aedsp16_mpu: "));
1207
1208         if (ae_config.init & INIT_MPU401)
1209                 return FALSE;
1210
1211 /*
1212  * We must request the CONFIG_AEDSP16_BASE region too because these are the I/O
1213  * ports to access card's control registers.
1214  */
1215         if (!(ae_config.init & (INIT_MSS | INIT_SBPRO))) {
1216                 if (!request_region(ae_config.base_io, IOBASE_REGION_SIZE,
1217                                         "aedsp16 (base)")) {
1218                         printk(
1219                         "AEDSP16 BASE I/O port region is already in use.\n");
1220                         return FALSE;
1221                 }
1222         }
1223
1224         ae_config.init |= INIT_MPU401;
1225
1226         DBG(("done.\n"));
1227
1228         return TRUE;
1229 }
1230
1231 static void uninit_aedsp16_mpu(void)
1232 {
1233         DBG(("uninit_aedsp16_mpu: "));
1234
1235         if ((!(ae_config.init & (INIT_MSS | INIT_SBPRO))) &&
1236            (ae_config.init & INIT_MPU401)) {
1237                 release_region(ae_config.base_io, IOBASE_REGION_SIZE);
1238                 DBG(("AEDSP16 base region released.\n"));
1239         }
1240
1241         ae_config.init &= ~INIT_MPU401;
1242
1243         DBG(("done.\n"));
1244 }
1245
1246 static int __init init_aedsp16(void)
1247 {
1248         int initialized = FALSE;
1249
1250         DBG(("Initializing BASE[0x%x] IRQ[%d] DMA[%d] MIRQ[%d]\n",
1251              ae_config.base_io,ae_config.irq,ae_config.dma,ae_config.mpu_irq));
1252
1253         if (ae_config.mss_base == -1) {
1254                 if (init_aedsp16_sb() == FALSE) {
1255                         uninit_aedsp16_sb();
1256                 } else {
1257                         initialized = TRUE;
1258                 }
1259         }
1260
1261         if (ae_config.mpu_base != -1) {
1262                 if (init_aedsp16_mpu() == FALSE) {
1263                         uninit_aedsp16_mpu();
1264                 } else {
1265                         initialized = TRUE;
1266                 }
1267         }
1268
1269 /*
1270  * In the sequence of init routines, the MSS init MUST be the last!
1271  * This because of the special register programming the MSS mode needs.
1272  * A board reset would disable the MSS mode restoring the default SBPRO
1273  * mode.
1274  */
1275         if (ae_config.mss_base != -1) {
1276                 if (init_aedsp16_mss() == FALSE) {
1277                         uninit_aedsp16_mss();
1278                 } else {
1279                         initialized = TRUE;
1280                 }
1281         }
1282
1283         if (initialized)
1284                 initialized = aedsp16_init_board();
1285         return initialized;
1286 }
1287
1288 static void __exit uninit_aedsp16(void)
1289 {
1290         if (ae_config.mss_base != -1)
1291                 uninit_aedsp16_mss();
1292         else
1293                 uninit_aedsp16_sb();
1294         if (ae_config.mpu_base != -1)
1295                 uninit_aedsp16_mpu();
1296 }
1297
1298 static int __initdata io = -1;
1299 static int __initdata irq = -1;
1300 static int __initdata dma = -1;
1301 static int __initdata mpu_irq = -1;
1302 static int __initdata mss_base = -1;
1303 static int __initdata mpu_base = -1;
1304
1305 module_param(io, int, 0);
1306 MODULE_PARM_DESC(io, "I/O base address (0x220 0x240)");
1307 module_param(irq, int, 0);
1308 MODULE_PARM_DESC(irq, "IRQ line (5 7 9 10 11)");
1309 module_param(dma, int, 0);
1310 MODULE_PARM_DESC(dma, "dma line (0 1 3)");
1311 module_param(mpu_irq, int, 0);
1312 MODULE_PARM_DESC(mpu_irq, "MPU-401 IRQ line (5 7 9 10 0)");
1313 module_param(mss_base, int, 0);
1314 MODULE_PARM_DESC(mss_base, "MSS emulation I/O base address (0x530 0xE80)");
1315 module_param(mpu_base, int, 0);
1316 MODULE_PARM_DESC(mpu_base,"MPU-401 I/O base address (0x300 0x310 0x320 0x330)");
1317 MODULE_AUTHOR("Riccardo Facchetti <fizban@tin.it>");
1318 MODULE_DESCRIPTION("Audio Excel DSP 16 Driver Version " VERSION);
1319 MODULE_LICENSE("GPL");
1320
1321 static int __init do_init_aedsp16(void) {
1322         printk("Audio Excel DSP 16 init driver Copyright (C) Riccardo Facchetti 1995-98\n");
1323         if (io == -1 || dma == -1 || irq == -1) {
1324                 printk(KERN_INFO "aedsp16: I/O, IRQ and DMA are mandatory\n");
1325                 return -EINVAL;
1326         }
1327
1328         ae_config.base_io = io;
1329         ae_config.irq = irq;
1330         ae_config.dma = dma;
1331
1332         ae_config.mss_base = mss_base;
1333         ae_config.mpu_base = mpu_base;
1334         ae_config.mpu_irq = mpu_irq;
1335
1336         if (init_aedsp16() == FALSE) {
1337                 printk(KERN_ERR "aedsp16: initialization failed\n");
1338                 /*
1339                  * XXX
1340                  * What error should we return here ?
1341                  */
1342                 return -EINVAL;
1343         }
1344         return 0;
1345 }
1346
1347 static void __exit cleanup_aedsp16(void) {
1348         uninit_aedsp16();
1349 }
1350
1351 module_init(do_init_aedsp16);
1352 module_exit(cleanup_aedsp16);
1353
1354 #ifndef MODULE
1355 static int __init setup_aedsp16(char *str)
1356 {
1357         /* io, irq, dma, mss_io, mpu_io, mpu_irq */
1358         int ints[7];
1359
1360         str = get_options(str, ARRAY_SIZE(ints), ints);
1361
1362         io       = ints[1];
1363         irq      = ints[2];
1364         dma      = ints[3];
1365         mss_base = ints[4];
1366         mpu_base = ints[5];
1367         mpu_irq  = ints[6];
1368         return 1;
1369 }
1370
1371 __setup("aedsp16=", setup_aedsp16);
1372 #endif