2 * TQM8xx(L) board specific definitions
4 * Copyright (c) 1999-2002 Wolfgang Denk (wd@denx.de)
8 #ifndef __MACH_TQM8xx_H
9 #define __MACH_TQM8xx_H
12 #include <asm/ppcboot.h>
15 #define TQM_IMMR_BASE 0xFFF00000 /* phys. addr of IMMR */
16 #define TQM_IMAP_SIZE (64 * 1024) /* size of mapped area */
18 #define IMAP_ADDR TQM_IMMR_BASE /* physical base address of IMMR area */
19 #define IMAP_SIZE TQM_IMAP_SIZE /* mapped size of IMMR area */
21 /*-----------------------------------------------------------------------
23 *-----------------------------------------------------------------------
26 #define PCMCIA_MEM_SIZE ( 64 << 20 )
29 # define MAX_HWIFS 1 /* overwrite default in include/asm-ppc/ide.h */
31 #else /* CONFIG_KUP4K */
33 # define MAX_HWIFS 2 /* overwrite default in include/asm-ppc/ide.h */
35 # include <asm/8xx_immap.h>
36 static __inline__
void ide_led(int on
)
38 volatile immap_t
*immap
= (immap_t
*)IMAP_ADDR
;
41 immap
->im_ioport
.iop_padat
&= ~0x80;
43 immap
->im_ioport
.iop_padat
|= 0x80;
46 # endif /* __ASSEMBLY__ */
47 # define IDE_LED(x) ide_led((x))
48 #endif /* CONFIG_KUP4K */
51 * Definitions for IDE0 Interface
53 #define IDE0_BASE_OFFSET 0
54 #define IDE0_DATA_REG_OFFSET (PCMCIA_MEM_SIZE + 0x320)
55 #define IDE0_ERROR_REG_OFFSET (2 * PCMCIA_MEM_SIZE + 0x320 + 1)
56 #define IDE0_NSECTOR_REG_OFFSET (2 * PCMCIA_MEM_SIZE + 0x320 + 2)
57 #define IDE0_SECTOR_REG_OFFSET (2 * PCMCIA_MEM_SIZE + 0x320 + 3)
58 #define IDE0_LCYL_REG_OFFSET (2 * PCMCIA_MEM_SIZE + 0x320 + 4)
59 #define IDE0_HCYL_REG_OFFSET (2 * PCMCIA_MEM_SIZE + 0x320 + 5)
60 #define IDE0_SELECT_REG_OFFSET (2 * PCMCIA_MEM_SIZE + 0x320 + 6)
61 #define IDE0_STATUS_REG_OFFSET (2 * PCMCIA_MEM_SIZE + 0x320 + 7)
62 #define IDE0_CONTROL_REG_OFFSET 0x0106
63 #define IDE0_IRQ_REG_OFFSET 0x000A /* not used */
65 /* define IO_BASE for PCMCIA */
66 #define _IO_BASE 0x80000000
67 #define _IO_BASE_SIZE (64<<10)
69 #define FEC_INTERRUPT 9 /* = SIU_LEVEL4 */
70 #define PHY_INTERRUPT 12 /* = IRQ6 */
71 #define IDE0_INTERRUPT 13
76 /*-----------------------------------------------------------------------
77 * CPM Ethernet through SCCx.
78 *-----------------------------------------------------------------------
82 /*** TQM823L, TQM850L ***********************************************/
84 #if defined(CONFIG_TQM823L) || defined(CONFIG_TQM850L)
85 /* Bits in parallel I/O port registers that have to be set/cleared
86 * to configure the pins for SCC1 use.
88 #define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
89 #define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
90 #define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
91 #define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
93 #define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
95 #define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
96 #define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
98 /* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
99 * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
101 #define SICR_ENET_MASK ((uint)0x0000ff00)
102 #define SICR_ENET_CLKRT ((uint)0x00002600)
103 #endif /* CONFIG_TQM823L, CONFIG_TQM850L */
105 /*** TQM860L ********************************************************/
107 #ifdef CONFIG_TQM860L
108 /* Bits in parallel I/O port registers that have to be set/cleared
109 * to configure the pins for SCC1 use.
111 #define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
112 #define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
113 #define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
114 #define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
116 #define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
117 #define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
118 #define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
120 /* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
121 * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
123 #define SICR_ENET_MASK ((uint)0x000000ff)
124 #define SICR_ENET_CLKRT ((uint)0x00000026)
125 #endif /* CONFIG_TQM860L */
127 /*** FPS850L *********************************************************/
129 #ifdef CONFIG_FPS850L
130 /* Bits in parallel I/O port registers that have to be set/cleared
131 * to configure the pins for SCC1 use.
133 #define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
134 #define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
135 #define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
136 #define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
138 #define PC_ENET_TENA ((ushort)0x0002) /* PC 14 */
139 #define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
140 #define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
142 /* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
143 * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
145 #define SICR_ENET_MASK ((uint)0x0000ff00)
146 #define SICR_ENET_CLKRT ((uint)0x00002600)
147 #endif /* CONFIG_FPS850L */
149 /* We don't use the 8259.
151 #define NR_8259_INTS 0
153 #endif /* !__ASSEMBLY__ */
154 #endif /* __MACH_TQM8xx_H */
155 #endif /* __KERNEL__ */