include/asm-m68knommu/MC68EZ328.h

   1
   2 /* include/asm-m68knommu/MC68EZ328.h: 'EZ328 control registers
   3  *
   4  * Copyright (C) 1999  Vladimir Gurevich <vgurevic@cisco.com>
   5  *                     Bear & Hare Software, Inc.
   6  *
   7  * Based on include/asm-m68knommu/MC68332.h
   8  * Copyright (C) 1998  Kenneth Albanowski <kjahds@kjahds.com>,
   9  *                     The Silver Hammer Group, Ltd.
  10  *
  11  */
  12
  13 #ifndef _MC68EZ328_H_
  14 #define _MC68EZ328_H_
  15
  16 #define BYTE_REF(addr) (*((volatile unsigned char*)addr))
  17 #define WORD_REF(addr) (*((volatile unsigned short*)addr))
  18 #define LONG_REF(addr) (*((volatile unsigned long*)addr))
  19
  20 #define PUT_FIELD(field, val) (((val) << field##_SHIFT) & field##_MASK)
  21 #define GET_FIELD(reg, field) (((reg) & field##_MASK) >> field##_SHIFT)
  22
  23 /**********
  24  *
  25  * 0xFFFFF0xx -- System Control
  26  *
  27  **********/
  28
  29 /*
  30  * System Control Register (SCR)
  31  */
  32 #define SCR_ADDR        0xfffff000
  33 #define SCR             BYTE_REF(SCR_ADDR)
  34
  35 #define SCR_WDTH8       0x01    /* 8-Bit Width Select */
  36 #define SCR_DMAP        0x04    /* Double Map */
  37 #define SCR_SO          0x08    /* Supervisor Only */
  38 #define SCR_BETEN       0x10    /* Bus-Error Time-Out Enable */
  39 #define SCR_PRV         0x20    /* Privilege Violation */
  40 #define SCR_WPV         0x40    /* Write Protect Violation */
  41 #define SCR_BETO        0x80    /* Bus-Error TimeOut */
  42
  43 /*
  44  * Silicon ID Register (Mask Revision Register (MRR) for '328 Compatibility)
  45  */
  46 #define MRR_ADDR 0xfffff004
  47 #define MRR      LONG_REF(MRR_ADDR)
  48
  49 /**********
  50  *
  51  * 0xFFFFF1xx -- Chip-Select logic
  52  *
  53  **********/
  54
  55 /*
  56  * Chip Select Group Base Registers
  57  */
  58 #define CSGBA_ADDR      0xfffff100
  59 #define CSGBB_ADDR      0xfffff102
  60
  61 #define CSGBC_ADDR      0xfffff104
  62 #define CSGBD_ADDR      0xfffff106
  63
  64 #define CSGBA           WORD_REF(CSGBA_ADDR)
  65 #define CSGBB           WORD_REF(CSGBB_ADDR)
  66 #define CSGBC           WORD_REF(CSGBC_ADDR)
  67 #define CSGBD           WORD_REF(CSGBD_ADDR)
  68
  69 /*
  70  * Chip Select Registers
  71  */
  72 #define CSA_ADDR        0xfffff110
  73 #define CSB_ADDR        0xfffff112
  74 #define CSC_ADDR        0xfffff114
  75 #define CSD_ADDR        0xfffff116
  76
  77 #define CSA             WORD_REF(CSA_ADDR)
  78 #define CSB             WORD_REF(CSB_ADDR)
  79 #define CSC             WORD_REF(CSC_ADDR)
  80 #define CSD             WORD_REF(CSD_ADDR)
  81
  82 #define CSA_EN          0x0001          /* Chip-Select Enable */
  83 #define CSA_SIZ_MASK    0x000e          /* Chip-Select Size */
  84 #define CSA_SIZ_SHIFT   1
  85 #define CSA_WS_MASK     0x0070          /* Wait State */
  86 #define CSA_WS_SHIFT    4
  87 #define CSA_BSW         0x0080          /* Data Bus Width */
  88 #define CSA_FLASH       0x0100          /* FLASH Memory Support */
  89 #define CSA_RO          0x8000          /* Read-Only */
  90
  91 #define CSB_EN          0x0001          /* Chip-Select Enable */
  92 #define CSB_SIZ_MASK    0x000e          /* Chip-Select Size */
  93 #define CSB_SIZ_SHIFT   1
  94 #define CSB_WS_MASK     0x0070          /* Wait State */
  95 #define CSB_WS_SHIFT    4
  96 #define CSB_BSW         0x0080          /* Data Bus Width */
  97 #define CSB_FLASH       0x0100          /* FLASH Memory Support */
  98 #define CSB_UPSIZ_MASK  0x1800          /* Unprotected memory block size */
  99 #define CSB_UPSIZ_SHIFT 11
 100 #define CSB_ROP         0x2000          /* Readonly if protected */
 101 #define CSB_SOP         0x4000          /* Supervisor only if protected */
 102 #define CSB_RO          0x8000          /* Read-Only */
 103
 104 #define CSC_EN          0x0001          /* Chip-Select Enable */
 105 #define CSC_SIZ_MASK    0x000e          /* Chip-Select Size */
 106 #define CSC_SIZ_SHIFT   1
 107 #define CSC_WS_MASK     0x0070          /* Wait State */
 108 #define CSC_WS_SHIFT    4
 109 #define CSC_BSW         0x0080          /* Data Bus Width */
 110 #define CSC_FLASH       0x0100          /* FLASH Memory Support */
 111 #define CSC_UPSIZ_MASK  0x1800          /* Unprotected memory block size */
 112 #define CSC_UPSIZ_SHIFT 11
 113 #define CSC_ROP         0x2000          /* Readonly if protected */
 114 #define CSC_SOP         0x4000          /* Supervisor only if protected */
 115 #define CSC_RO          0x8000          /* Read-Only */
 116
 117 #define CSD_EN          0x0001          /* Chip-Select Enable */
 118 #define CSD_SIZ_MASK    0x000e          /* Chip-Select Size */
 119 #define CSD_SIZ_SHIFT   1
 120 #define CSD_WS_MASK     0x0070          /* Wait State */
 121 #define CSD_WS_SHIFT    4
 122 #define CSD_BSW         0x0080          /* Data Bus Width */
 123 #define CSD_FLASH       0x0100          /* FLASH Memory Support */
 124 #define CSD_DRAM        0x0200          /* Dram Selection */
 125 #define CSD_COMB        0x0400          /* Combining */
 126 #define CSD_UPSIZ_MASK  0x1800          /* Unprotected memory block size */
 127 #define CSD_UPSIZ_SHIFT 11
 128 #define CSD_ROP         0x2000          /* Readonly if protected */
 129 #define CSD_SOP         0x4000          /* Supervisor only if protected */
 130 #define CSD_RO          0x8000          /* Read-Only */
 131
 132 /*
 133  * Emulation Chip-Select Register
 134  */
 135 #define EMUCS_ADDR      0xfffff118
 136 #define EMUCS           WORD_REF(EMUCS_ADDR)
 137
 138 #define EMUCS_WS_MASK   0x0070
 139 #define EMUCS_WS_SHIFT  4
 140
 141 /**********
 142  *
 143  * 0xFFFFF2xx -- Phase Locked Loop (PLL) & Power Control
 144  *
 145  **********/
 146
 147 /*
 148  * PLL Control Register
 149  */
 150 #define PLLCR_ADDR      0xfffff200
 151 #define PLLCR           WORD_REF(PLLCR_ADDR)
 152
 153 #define PLLCR_DISPLL           0x0008   /* Disable PLL */
 154 #define PLLCR_CLKEN            0x0010   /* Clock (CLKO pin) enable */
 155 #define PLLCR_PRESC            0x0020   /* VCO prescaler */
 156 #define PLLCR_SYSCLK_SEL_MASK  0x0700   /* System Clock Selection */
 157 #define PLLCR_SYSCLK_SEL_SHIFT 8
 158 #define PLLCR_LCDCLK_SEL_MASK  0x3800   /* LCD Clock Selection */
 159 #define PLLCR_LCDCLK_SEL_SHIFT 11
 160
 161 /* '328-compatible definitions */
 162 #define PLLCR_PIXCLK_SEL_MASK   PLLCR_LCDCLK_SEL_MASK
 163 #define PLLCR_PIXCLK_SEL_SHIFT  PLLCR_LCDCLK_SEL_SHIFT
 164
 165 /*
 166  * PLL Frequency Select Register
 167  */
 168 #define PLLFSR_ADDR     0xfffff202
 169 #define PLLFSR          WORD_REF(PLLFSR_ADDR)
 170
 171 #define PLLFSR_PC_MASK  0x00ff          /* P Count */
 172 #define PLLFSR_PC_SHIFT 0
 173 #define PLLFSR_QC_MASK  0x0f00          /* Q Count */
 174 #define PLLFSR_QC_SHIFT 8
 175 #define PLLFSR_PROT     0x4000          /* Protect P & Q */
 176 #define PLLFSR_CLK32    0x8000          /* Clock 32 (kHz) */
 177
 178 /*
 179  * Power Control Register
 180  */
 181 #define PCTRL_ADDR      0xfffff207
 182 #define PCTRL           BYTE_REF(PCTRL_ADDR)
 183
 184 #define PCTRL_WIDTH_MASK        0x1f    /* CPU Clock bursts width */
 185 #define PCTRL_WIDTH_SHIFT       0
 186 #define PCTRL_PCEN              0x80    /* Power Control Enable */
 187
 188 /**********
 189  *
 190  * 0xFFFFF3xx -- Interrupt Controller
 191  *
 192  **********/
 193
 194 /*
 195  * Interrupt Vector Register
 196  */
 197 #define IVR_ADDR        0xfffff300
 198 #define IVR             BYTE_REF(IVR_ADDR)
 199
 200 #define IVR_VECTOR_MASK 0xF8
 201
 202 /*
 203  * Interrupt control Register
 204  */
 205 #define ICR_ADDR        0xfffff302
 206 #define ICR             WORD_REF(ICR_ADDR)
 207
 208 #define ICR_POL5        0x0080  /* Polarity Control for IRQ5 */
 209 #define ICR_ET6         0x0100  /* Edge Trigger Select for IRQ6 */
 210 #define ICR_ET3         0x0200  /* Edge Trigger Select for IRQ3 */
 211 #define ICR_ET2         0x0400  /* Edge Trigger Select for IRQ2 */
 212 #define ICR_ET1         0x0800  /* Edge Trigger Select for IRQ1 */
 213 #define ICR_POL6        0x1000  /* Polarity Control for IRQ6 */
 214 #define ICR_POL3        0x2000  /* Polarity Control for IRQ3 */
 215 #define ICR_POL2        0x4000  /* Polarity Control for IRQ2 */
 216 #define ICR_POL1        0x8000  /* Polarity Control for IRQ1 */
 217
 218 /*
 219  * Interrupt Mask Register
 220  */
 221 #define IMR_ADDR        0xfffff304
 222 #define IMR             LONG_REF(IMR_ADDR)
 223
 224 /*
 225  * Define the names for bit positions first. This is useful for
 226  * request_irq
 227  */
 228 #define SPI_IRQ_NUM     0       /* SPI interrupt */
 229 #define TMR_IRQ_NUM     1       /* Timer interrupt */
 230 #define UART_IRQ_NUM    2       /* UART interrupt */
 231 #define WDT_IRQ_NUM     3       /* Watchdog Timer interrupt */
 232 #define RTC_IRQ_NUM     4       /* RTC interrupt */
 233 #define KB_IRQ_NUM      6       /* Keyboard Interrupt */
 234 #define PWM_IRQ_NUM     7       /* Pulse-Width Modulator int. */
 235 #define INT0_IRQ_NUM    8       /* External INT0 */
 236 #define INT1_IRQ_NUM    9       /* External INT1 */
 237 #define INT2_IRQ_NUM    10      /* External INT2 */
 238 #define INT3_IRQ_NUM    11      /* External INT3 */
 239 #define IRQ1_IRQ_NUM    16      /* IRQ1 */
 240 #define IRQ2_IRQ_NUM    17      /* IRQ2 */
 241 #define IRQ3_IRQ_NUM    18      /* IRQ3 */
 242 #define IRQ6_IRQ_NUM    19      /* IRQ6 */
 243 #define IRQ5_IRQ_NUM    20      /* IRQ5 */
 244 #define SAM_IRQ_NUM     22      /* Sampling Timer for RTC */
 245 #define EMIQ_IRQ_NUM    23      /* Emulator Interrupt */
 246
 247 /* '328-compatible definitions */
 248 #define SPIM_IRQ_NUM    SPI_IRQ_NUM
 249 #define TMR1_IRQ_NUM    TMR_IRQ_NUM
 250
 251 /*
 252  * Here go the bitmasks themselves
 253  */
 254 #define IMR_MSPI        (1 << SPI_IRQ_NUM)      /* Mask SPI interrupt */
 255 #define IMR_MTMR        (1 << TMR_IRQ_NUM)      /* Mask Timer interrupt */
 256 #define IMR_MUART       (1 << UART_IRQ_NUM)     /* Mask UART interrupt */
 257 #define IMR_MWDT        (1 << WDT_IRQ_NUM)      /* Mask Watchdog Timer interrupt */
 258 #define IMR_MRTC        (1 << RTC_IRQ_NUM)      /* Mask RTC interrupt */
 259 #define IMR_MKB         (1 << KB_IRQ_NUM)       /* Mask Keyboard Interrupt */
 260 #define IMR_MPWM        (1 << PWM_IRQ_NUM)      /* Mask Pulse-Width Modulator int. */
 261 #define IMR_MINT0       (1 << INT0_IRQ_NUM)     /* Mask External INT0 */
 262 #define IMR_MINT1       (1 << INT1_IRQ_NUM)     /* Mask External INT1 */
 263 #define IMR_MINT2       (1 << INT2_IRQ_NUM)     /* Mask External INT2 */
 264 #define IMR_MINT3       (1 << INT3_IRQ_NUM)     /* Mask External INT3 */
 265 #define IMR_MIRQ1       (1 << IRQ1_IRQ_NUM)     /* Mask IRQ1 */
 266 #define IMR_MIRQ2       (1 << IRQ2_IRQ_NUM)     /* Mask IRQ2 */
 267 #define IMR_MIRQ3       (1 << IRQ3_IRQ_NUM)     /* Mask IRQ3 */
 268 #define IMR_MIRQ6       (1 << IRQ6_IRQ_NUM)     /* Mask IRQ6 */
 269 #define IMR_MIRQ5       (1 << IRQ5_IRQ_NUM)     /* Mask IRQ5 */
 270 #define IMR_MSAM        (1 << SAM_IRQ_NUM)      /* Mask Sampling Timer for RTC */
 271 #define IMR_MEMIQ       (1 << EMIQ_IRQ_NUM)     /* Mask Emulator Interrupt */
 272
 273 /* '328-compatible definitions */
 274 #define IMR_MSPIM       IMR_MSPI
 275 #define IMR_MTMR1       IMR_MTMR
 276
 277 /*
 278  * Interrupt Status Register
 279  */
 280 #define ISR_ADDR        0xfffff30c
 281 #define ISR             LONG_REF(ISR_ADDR)
 282
 283 #define ISR_SPI         (1 << SPI_IRQ_NUM)      /* SPI interrupt */
 284 #define ISR_TMR         (1 << TMR_IRQ_NUM)      /* Timer interrupt */
 285 #define ISR_UART        (1 << UART_IRQ_NUM)     /* UART interrupt */
 286 #define ISR_WDT         (1 << WDT_IRQ_NUM)      /* Watchdog Timer interrupt */
 287 #define ISR_RTC         (1 << RTC_IRQ_NUM)      /* RTC interrupt */
 288 #define ISR_KB          (1 << KB_IRQ_NUM)       /* Keyboard Interrupt */
 289 #define ISR_PWM         (1 << PWM_IRQ_NUM)      /* Pulse-Width Modulator interrupt */
 290 #define ISR_INT0        (1 << INT0_IRQ_NUM)     /* External INT0 */
 291 #define ISR_INT1        (1 << INT1_IRQ_NUM)     /* External INT1 */
 292 #define ISR_INT2        (1 << INT2_IRQ_NUM)     /* External INT2 */
 293 #define ISR_INT3        (1 << INT3_IRQ_NUM)     /* External INT3 */
 294 #define ISR_IRQ1        (1 << IRQ1_IRQ_NUM)     /* IRQ1 */
 295 #define ISR_IRQ2        (1 << IRQ2_IRQ_NUM)     /* IRQ2 */
 296 #define ISR_IRQ3        (1 << IRQ3_IRQ_NUM)     /* IRQ3 */
 297 #define ISR_IRQ6        (1 << IRQ6_IRQ_NUM)     /* IRQ6 */
 298 #define ISR_IRQ5        (1 << IRQ5_IRQ_NUM)     /* IRQ5 */
 299 #define ISR_SAM         (1 << SAM_IRQ_NUM)      /* Sampling Timer for RTC */
 300 #define ISR_EMIQ        (1 << EMIQ_IRQ_NUM)     /* Emulator Interrupt */
 301
 302 /* '328-compatible definitions */
 303 #define ISR_SPIM        ISR_SPI
 304 #define ISR_TMR1        ISR_TMR
 305
 306 /*
 307  * Interrupt Pending Register
 308  */
 309 #define IPR_ADDR        0xfffff30c
 310 #define IPR             LONG_REF(IPR_ADDR)
 311
 312 #define IPR_SPI         (1 << SPI_IRQ_NUM)      /* SPI interrupt */
 313 #define IPR_TMR         (1 << TMR_IRQ_NUM)      /* Timer interrupt */
 314 #define IPR_UART        (1 << UART_IRQ_NUM)     /* UART interrupt */
 315 #define IPR_WDT         (1 << WDT_IRQ_NUM)      /* Watchdog Timer interrupt */
 316 #define IPR_RTC         (1 << RTC_IRQ_NUM)      /* RTC interrupt */
 317 #define IPR_KB          (1 << KB_IRQ_NUM)       /* Keyboard Interrupt */
 318 #define IPR_PWM         (1 << PWM_IRQ_NUM)      /* Pulse-Width Modulator interrupt */
 319 #define IPR_INT0        (1 << INT0_IRQ_NUM)     /* External INT0 */
 320 #define IPR_INT1        (1 << INT1_IRQ_NUM)     /* External INT1 */
 321 #define IPR_INT2        (1 << INT2_IRQ_NUM)     /* External INT2 */
 322 #define IPR_INT3        (1 << INT3_IRQ_NUM)     /* External INT3 */
 323 #define IPR_IRQ1        (1 << IRQ1_IRQ_NUM)     /* IRQ1 */
 324 #define IPR_IRQ2        (1 << IRQ2_IRQ_NUM)     /* IRQ2 */
 325 #define IPR_IRQ3        (1 << IRQ3_IRQ_NUM)     /* IRQ3 */
 326 #define IPR_IRQ6        (1 << IRQ6_IRQ_NUM)     /* IRQ6 */
 327 #define IPR_IRQ5        (1 << IRQ5_IRQ_NUM)     /* IRQ5 */
 328 #define IPR_SAM         (1 << SAM_IRQ_NUM)      /* Sampling Timer for RTC */
 329 #define IPR_EMIQ        (1 << EMIQ_IRQ_NUM)     /* Emulator Interrupt */
 330
 331 /* '328-compatible definitions */
 332 #define IPR_SPIM        IPR_SPI
 333 #define IPR_TMR1        IPR_TMR
 334
 335 /**********
 336  *
 337  * 0xFFFFF4xx -- Parallel Ports
 338  *
 339  **********/
 340
 341 /*
 342  * Port A
 343  */
 344 #define PADIR_ADDR      0xfffff400              /* Port A direction reg */
 345 #define PADATA_ADDR     0xfffff401              /* Port A data register */
 346 #define PAPUEN_ADDR     0xfffff402              /* Port A Pull-Up enable reg */
 347
 348 #define PADIR           BYTE_REF(PADIR_ADDR)
 349 #define PADATA          BYTE_REF(PADATA_ADDR)
 350 #define PAPUEN          BYTE_REF(PAPUEN_ADDR)
 351
 352 #define PA(x)           (1 << (x))
 353
 354 /*
 355  * Port B
 356  */
 357 #define PBDIR_ADDR      0xfffff408              /* Port B direction reg */
 358 #define PBDATA_ADDR     0xfffff409              /* Port B data register */
 359 #define PBPUEN_ADDR     0xfffff40a              /* Port B Pull-Up enable reg */
 360 #define PBSEL_ADDR      0xfffff40b              /* Port B Select Register */
 361
 362 #define PBDIR           BYTE_REF(PBDIR_ADDR)
 363 #define PBDATA          BYTE_REF(PBDATA_ADDR)
 364 #define PBPUEN          BYTE_REF(PBPUEN_ADDR)
 365 #define PBSEL           BYTE_REF(PBSEL_ADDR)
 366
 367 #define PB(x)           (1 << (x))
 368
 369 #define PB_CSB0         0x01    /* Use CSB0      as PB[0] */
 370 #define PB_CSB1         0x02    /* Use CSB1      as PB[1] */
 371 #define PB_CSC0_RAS0    0x04    /* Use CSC0/RAS0 as PB[2] */
 372 #define PB_CSC1_RAS1    0x08    /* Use CSC1/RAS1 as PB[3] */
 373 #define PB_CSD0_CAS0    0x10    /* Use CSD0/CAS0 as PB[4] */
 374 #define PB_CSD1_CAS1    0x20    /* Use CSD1/CAS1 as PB[5] */
 375 #define PB_TIN_TOUT     0x40    /* Use TIN/TOUT  as PB[6] */
 376 #define PB_PWMO         0x80    /* Use PWMO      as PB[7] */
 377
 378 /*
 379  * Port C
 380  */
 381 #define PCDIR_ADDR      0xfffff410              /* Port C direction reg */
 382 #define PCDATA_ADDR     0xfffff411              /* Port C data register */
 383 #define PCPDEN_ADDR     0xfffff412              /* Port C Pull-Down enb. reg */
 384 #define PCSEL_ADDR      0xfffff413              /* Port C Select Register */
 385
 386 #define PCDIR           BYTE_REF(PCDIR_ADDR)
 387 #define PCDATA          BYTE_REF(PCDATA_ADDR)
 388 #define PCPDEN          BYTE_REF(PCPDEN_ADDR)
 389 #define PCSEL           BYTE_REF(PCSEL_ADDR)
 390
 391 #define PC(x)           (1 << (x))
 392
 393 #define PC_LD0          0x01    /* Use LD0  as PC[0] */
 394 #define PC_LD1          0x02    /* Use LD1  as PC[1] */
 395 #define PC_LD2          0x04    /* Use LD2  as PC[2] */
 396 #define PC_LD3          0x08    /* Use LD3  as PC[3] */
 397 #define PC_LFLM         0x10    /* Use LFLM as PC[4] */
 398 #define PC_LLP          0x20    /* Use LLP  as PC[5] */
 399 #define PC_LCLK         0x40    /* Use LCLK as PC[6] */
 400 #define PC_LACD         0x80    /* Use LACD as PC[7] */
 401
 402 /*
 403  * Port D
 404  */
 405 #define PDDIR_ADDR      0xfffff418              /* Port D direction reg */
 406 #define PDDATA_ADDR     0xfffff419              /* Port D data register */
 407 #define PDPUEN_ADDR     0xfffff41a              /* Port D Pull-Up enable reg */
 408 #define PDSEL_ADDR      0xfffff41b              /* Port D Select Register */
 409 #define PDPOL_ADDR      0xfffff41c              /* Port D Polarity Register */
 410 #define PDIRQEN_ADDR    0xfffff41d              /* Port D IRQ enable register */
 411 #define PDKBEN_ADDR     0xfffff41e              /* Port D Keyboard Enable reg */
 412 #define PDIQEG_ADDR     0xfffff41f              /* Port D IRQ Edge Register */
 413
 414 #define PDDIR           BYTE_REF(PDDIR_ADDR)
 415 #define PDDATA          BYTE_REF(PDDATA_ADDR)
 416 #define PDPUEN          BYTE_REF(PDPUEN_ADDR)
 417 #define PDSEL           BYTE_REF(PDSEL_ADDR)
 418 #define PDPOL           BYTE_REF(PDPOL_ADDR)
 419 #define PDIRQEN         BYTE_REF(PDIRQEN_ADDR)
 420 #define PDKBEN          BYTE_REF(PDKBEN_ADDR)
 421 #define PDIQEG          BYTE_REF(PDIQEG_ADDR)
 422
 423 #define PD(x)           (1 << (x))
 424
 425 #define PD_INT0         0x01    /* Use INT0 as PD[0] */
 426 #define PD_INT1         0x02    /* Use INT1 as PD[1] */
 427 #define PD_INT2         0x04    /* Use INT2 as PD[2] */
 428 #define PD_INT3         0x08    /* Use INT3 as PD[3] */
 429 #define PD_IRQ1         0x10    /* Use IRQ1 as PD[4] */
 430 #define PD_IRQ2         0x20    /* Use IRQ2 as PD[5] */
 431 #define PD_IRQ3         0x40    /* Use IRQ3 as PD[6] */
 432 #define PD_IRQ6         0x80    /* Use IRQ6 as PD[7] */
 433
 434 /*
 435  * Port E
 436  */
 437 #define PEDIR_ADDR      0xfffff420              /* Port E direction reg */
 438 #define PEDATA_ADDR     0xfffff421              /* Port E data register */
 439 #define PEPUEN_ADDR     0xfffff422              /* Port E Pull-Up enable reg */
 440 #define PESEL_ADDR      0xfffff423              /* Port E Select Register */
 441
 442 #define PEDIR           BYTE_REF(PEDIR_ADDR)
 443 #define PEDATA          BYTE_REF(PEDATA_ADDR)
 444 #define PEPUEN          BYTE_REF(PEPUEN_ADDR)
 445 #define PESEL           BYTE_REF(PESEL_ADDR)
 446
 447 #define PE(x)           (1 << (x))
 448
 449 #define PE_SPMTXD       0x01    /* Use SPMTXD as PE[0] */
 450 #define PE_SPMRXD       0x02    /* Use SPMRXD as PE[1] */
 451 #define PE_SPMCLK       0x04    /* Use SPMCLK as PE[2] */
 452 #define PE_DWE          0x08    /* Use DWE    as PE[3] */
 453 #define PE_RXD          0x10    /* Use RXD    as PE[4] */
 454 #define PE_TXD          0x20    /* Use TXD    as PE[5] */
 455 #define PE_RTS          0x40    /* Use RTS    as PE[6] */
 456 #define PE_CTS          0x80    /* Use CTS    as PE[7] */
 457
 458 /*
 459  * Port F
 460  */
 461 #define PFDIR_ADDR      0xfffff428              /* Port F direction reg */
 462 #define PFDATA_ADDR     0xfffff429              /* Port F data register */
 463 #define PFPUEN_ADDR     0xfffff42a              /* Port F Pull-Up enable reg */
 464 #define PFSEL_ADDR      0xfffff42b              /* Port F Select Register */
 465
 466 #define PFDIR           BYTE_REF(PFDIR_ADDR)
 467 #define PFDATA          BYTE_REF(PFDATA_ADDR)
 468 #define PFPUEN          BYTE_REF(PFPUEN_ADDR)
 469 #define PFSEL           BYTE_REF(PFSEL_ADDR)
 470
 471 #define PF(x)           (1 << (x))
 472
 473 #define PF_LCONTRAST    0x01    /* Use LCONTRAST as PF[0] */
 474 #define PF_IRQ5         0x02    /* Use IRQ5      as PF[1] */
 475 #define PF_CLKO         0x04    /* Use CLKO      as PF[2] */
 476 #define PF_A20          0x08    /* Use A20       as PF[3] */
 477 #define PF_A21          0x10    /* Use A21       as PF[4] */
 478 #define PF_A22          0x20    /* Use A22       as PF[5] */
 479 #define PF_A23          0x40    /* Use A23       as PF[6] */
 480 #define PF_CSA1         0x80    /* Use CSA1      as PF[7] */
 481
 482 /*
 483  * Port G
 484  */
 485 #define PGDIR_ADDR      0xfffff430              /* Port G direction reg */
 486 #define PGDATA_ADDR     0xfffff431              /* Port G data register */
 487 #define PGPUEN_ADDR     0xfffff432              /* Port G Pull-Up enable reg */
 488 #define PGSEL_ADDR      0xfffff433              /* Port G Select Register */
 489
 490 #define PGDIR           BYTE_REF(PGDIR_ADDR)
 491 #define PGDATA          BYTE_REF(PGDATA_ADDR)
 492 #define PGPUEN          BYTE_REF(PGPUEN_ADDR)
 493 #define PGSEL           BYTE_REF(PGSEL_ADDR)
 494
 495 #define PG(x)           (1 << (x))
 496
 497 #define PG_BUSW_DTACK   0x01    /* Use BUSW/DTACK as PG[0] */
 498 #define PG_A0           0x02    /* Use A0         as PG[1] */
 499 #define PG_EMUIRQ       0x04    /* Use EMUIRQ     as PG[2] */
 500 #define PG_HIZ_P_D      0x08    /* Use HIZ/P/D    as PG[3] */
 501 #define PG_EMUCS        0x10    /* Use EMUCS      as PG[4] */
 502 #define PG_EMUBRK       0x20    /* Use EMUBRK     as PG[5] */
 503
 504 /**********
 505  *
 506  * 0xFFFFF5xx -- Pulse-Width Modulator (PWM)
 507  *
 508  **********/
 509
 510 /*
 511  * PWM Control Register
 512  */
 513 #define PWMC_ADDR       0xfffff500
 514 #define PWMC            WORD_REF(PWMC_ADDR)
 515
 516 #define PWMC_CLKSEL_MASK        0x0003  /* Clock Selection */
 517 #define PWMC_CLKSEL_SHIFT       0
 518 #define PWMC_REPEAT_MASK        0x000c  /* Sample Repeats */
 519 #define PWMC_REPEAT_SHIFT       2
 520 #define PWMC_EN                 0x0010  /* Enable PWM */
 521 #define PMNC_FIFOAV             0x0020  /* FIFO Available */
 522 #define PWMC_IRQEN              0x0040  /* Interrupt Request Enable */
 523 #define PWMC_IRQ                0x0080  /* Interrupt Request (FIFO empty) */
 524 #define PWMC_PRESCALER_MASK     0x7f00  /* Incoming Clock prescaler */
 525 #define PWMC_PRESCALER_SHIFT    8
 526 #define PWMC_CLKSRC             0x8000  /* Clock Source Select */
 527
 528 /* '328-compatible definitions */
 529 #define PWMC_PWMEN      PWMC_EN
 530
 531 /*
 532  * PWM Sample Register
 533  */
 534 #define PWMS_ADDR       0xfffff502
 535 #define PWMS            WORD_REF(PWMS_ADDR)
 536
 537 /*
 538  * PWM Period Register
 539  */
 540 #define PWMP_ADDR       0xfffff504
 541 #define PWMP            BYTE_REF(PWMP_ADDR)
 542
 543 /*
 544  * PWM Counter Register
 545  */
 546 #define PWMCNT_ADDR     0xfffff505
 547 #define PWMCNT          BYTE_REF(PWMCNT_ADDR)
 548
 549 /**********
 550  *
 551  * 0xFFFFF6xx -- General-Purpose Timer
 552  *
 553  **********/
 554
 555 /*
 556  * Timer Control register
 557  */
 558 #define TCTL_ADDR       0xfffff600
 559 #define TCTL            WORD_REF(TCTL_ADDR)
 560
 561 #define TCTL_TEN                0x0001  /* Timer Enable  */
 562 #define TCTL_CLKSOURCE_MASK     0x000e  /* Clock Source: */
 563 #define   TCTL_CLKSOURCE_STOP      0x0000       /* Stop count (disabled)    */
 564 #define   TCTL_CLKSOURCE_SYSCLK    0x0002       /* SYSCLK to prescaler      */
 565 #define   TCTL_CLKSOURCE_SYSCLK_16 0x0004       /* SYSCLK/16 to prescaler   */
 566 #define   TCTL_CLKSOURCE_TIN       0x0006       /* TIN to prescaler         */
 567 #define   TCTL_CLKSOURCE_32KHZ     0x0008       /* 32kHz clock to prescaler */
 568 #define TCTL_IRQEN              0x0010  /* IRQ Enable    */
 569 #define TCTL_OM                 0x0020  /* Output Mode   */
 570 #define TCTL_CAP_MASK           0x00c0  /* Capture Edge: */
 571 #define   TCTL_CAP_RE           0x0040          /* Capture on rizing edge   */
 572 #define   TCTL_CAP_FE           0x0080          /* Capture on falling edge  */
 573 #define TCTL_FRR                0x0010  /* Free-Run Mode */
 574
 575 /* '328-compatible definitions */
 576 #define TCTL1_ADDR      TCTL_ADDR
 577 #define TCTL1           TCTL
 578
 579 /*
 580  * Timer Prescaler Register
 581  */
 582 #define TPRER_ADDR      0xfffff602
 583 #define TPRER           WORD_REF(TPRER_ADDR)
 584
 585 /* '328-compatible definitions */
 586 #define TPRER1_ADDR     TPRER_ADDR
 587 #define TPRER1          TPRER
 588
 589 /*
 590  * Timer Compare Register
 591  */
 592 #define TCMP_ADDR       0xfffff604
 593 #define TCMP            WORD_REF(TCMP_ADDR)
 594
 595 /* '328-compatible definitions */
 596 #define TCMP1_ADDR      TCMP_ADDR
 597 #define TCMP1           TCMP
 598
 599 /*
 600  * Timer Capture register
 601  */
 602 #define TCR_ADDR        0xfffff606
 603 #define TCR             WORD_REF(TCR_ADDR)
 604
 605 /* '328-compatible definitions */
 606 #define TCR1_ADDR       TCR_ADDR
 607 #define TCR1            TCR
 608
 609 /*
 610  * Timer Counter Register
 611  */
 612 #define TCN_ADDR        0xfffff608
 613 #define TCN             WORD_REF(TCN_ADDR)
 614
 615 /* '328-compatible definitions */
 616 #define TCN1_ADDR       TCN_ADDR
 617 #define TCN1            TCN
 618
 619 /*
 620  * Timer Status Register
 621  */
 622 #define TSTAT_ADDR      0xfffff60a
 623 #define TSTAT           WORD_REF(TSTAT_ADDR)
 624
 625 #define TSTAT_COMP      0x0001          /* Compare Event occurred */
 626 #define TSTAT_CAPT      0x0001          /* Capture Event occurred */
 627
 628 /* '328-compatible definitions */
 629 #define TSTAT1_ADDR     TSTAT_ADDR
 630 #define TSTAT1          TSTAT
 631
 632 /**********
 633  *
 634  * 0xFFFFF8xx -- Serial Periferial Interface Master (SPIM)
 635  *
 636  **********/
 637
 638 /*
 639  * SPIM Data Register
 640  */
 641 #define SPIMDATA_ADDR   0xfffff800
 642 #define SPIMDATA        WORD_REF(SPIMDATA_ADDR)
 643
 644 /*
 645  * SPIM Control/Status Register
 646  */
 647 #define SPIMCONT_ADDR   0xfffff802
 648 #define SPIMCONT        WORD_REF(SPIMCONT_ADDR)
 649
 650 #define SPIMCONT_BIT_COUNT_MASK  0x000f /* Transfer Length in Bytes */
 651 #define SPIMCONT_BIT_COUNT_SHIFT 0
 652 #define SPIMCONT_POL             0x0010 /* SPMCLK Signel Polarity */
 653 #define SPIMCONT_PHA             0x0020 /* Clock/Data phase relationship */
 654 #define SPIMCONT_IRQEN           0x0040 /* IRQ Enable */
 655 #define SPIMCONT_IRQ             0x0080 /* Interrupt Request */
 656 #define SPIMCONT_XCH             0x0100 /* Exchange */
 657 #define SPIMCONT_ENABLE          0x0200 /* Enable SPIM */
 658 #define SPIMCONT_DATA_RATE_MASK  0xe000 /* SPIM Data Rate */
 659 #define SPIMCONT_DATA_RATE_SHIFT 13
 660
 661 /* '328-compatible definitions */
 662 #define SPIMCONT_SPIMIRQ        SPIMCONT_IRQ
 663 #define SPIMCONT_SPIMEN         SPIMCONT_ENABLE
 664
 665 /**********
 666  *
 667  * 0xFFFFF9xx -- UART
 668  *
 669  **********/
 670
 671 /*
 672  * UART Status/Control Register
 673  */
 674 #define USTCNT_ADDR     0xfffff900
 675 #define USTCNT          WORD_REF(USTCNT_ADDR)
 676
 677 #define USTCNT_TXAE     0x0001  /* Transmitter Available Interrupt Enable */
 678 #define USTCNT_TXHE     0x0002  /* Transmitter Half Empty Enable */
 679 #define USTCNT_TXEE     0x0004  /* Transmitter Empty Interrupt Enable */
 680 #define USTCNT_RXRE     0x0008  /* Receiver Ready Interrupt Enable */
 681 #define USTCNT_RXHE     0x0010  /* Receiver Half-Full Interrupt Enable */
 682 #define USTCNT_RXFE     0x0020  /* Receiver Full Interrupt Enable */
 683 #define USTCNT_CTSD     0x0040  /* CTS Delta Interrupt Enable */
 684 #define USTCNT_ODEN     0x0080  /* Old Data Interrupt Enable */
 685 #define USTCNT_8_7      0x0100  /* Eight or seven-bit transmission */
 686 #define USTCNT_STOP     0x0200  /* Stop bit transmission */
 687 #define USTCNT_ODD      0x0400  /* Odd Parity */
 688 #define USTCNT_PEN      0x0800  /* Parity Enable */
 689 #define USTCNT_CLKM     0x1000  /* Clock Mode Select */
 690 #define USTCNT_TXEN     0x2000  /* Transmitter Enable */
 691 #define USTCNT_RXEN     0x4000  /* Receiver Enable */
 692 #define USTCNT_UEN      0x8000  /* UART Enable */
 693
 694 /* '328-compatible definitions */
 695 #define USTCNT_TXAVAILEN        USTCNT_TXAE
 696 #define USTCNT_TXHALFEN         USTCNT_TXHE
 697 #define USTCNT_TXEMPTYEN        USTCNT_TXEE
 698 #define USTCNT_RXREADYEN        USTCNT_RXRE
 699 #define USTCNT_RXHALFEN         USTCNT_RXHE
 700 #define USTCNT_RXFULLEN         USTCNT_RXFE
 701 #define USTCNT_CTSDELTAEN       USTCNT_CTSD
 702 #define USTCNT_ODD_EVEN         USTCNT_ODD
 703 #define USTCNT_PARITYEN         USTCNT_PEN
 704 #define USTCNT_CLKMODE          USTCNT_CLKM
 705 #define USTCNT_UARTEN           USTCNT_UEN
 706
 707 /*
 708  * UART Baud Control Register
 709  */
 710 #define UBAUD_ADDR      0xfffff902
 711 #define UBAUD           WORD_REF(UBAUD_ADDR)
 712
 713 #define UBAUD_PRESCALER_MASK    0x003f  /* Actual divisor is 65 - PRESCALER */
 714 #define UBAUD_PRESCALER_SHIFT   0
 715 #define UBAUD_DIVIDE_MASK       0x0700  /* Baud Rate freq. divizor */
 716 #define UBAUD_DIVIDE_SHIFT      8
 717 #define UBAUD_BAUD_SRC          0x0800  /* Baud Rate Source */
 718 #define UBAUD_UCLKDIR           0x2000  /* UCLK Direction */
 719
 720 /*
 721  * UART Receiver Register
 722  */
 723 #define URX_ADDR        0xfffff904
 724 #define URX             WORD_REF(URX_ADDR)
 725
 726 #define URX_RXDATA_ADDR 0xfffff905
 727 #define URX_RXDATA      BYTE_REF(URX_RXDATA_ADDR)
 728
 729 #define URX_RXDATA_MASK  0x00ff /* Received data */
 730 #define URX_RXDATA_SHIFT 0
 731 #define URX_PARITY_ERROR 0x0100 /* Parity Error */
 732 #define URX_BREAK        0x0200 /* Break Detected */
 733 #define URX_FRAME_ERROR  0x0400 /* Framing Error */
 734 #define URX_OVRUN        0x0800 /* Serial Overrun */
 735 #define URX_OLD_DATA     0x1000 /* Old data in FIFO */
 736 #define URX_DATA_READY   0x2000 /* Data Ready (FIFO not empty) */
 737 #define URX_FIFO_HALF    0x4000 /* FIFO is Half-Full */
 738 #define URX_FIFO_FULL    0x8000 /* FIFO is Full */
 739
 740 /*
 741  * UART Transmitter Register
 742  */
 743 #define UTX_ADDR        0xfffff906
 744 #define UTX             WORD_REF(UTX_ADDR)
 745
 746 #define UTX_TXDATA_ADDR 0xfffff907
 747 #define UTX_TXDATA      BYTE_REF(UTX_TXDATA_ADDR)
 748
 749 #define UTX_TXDATA_MASK  0x00ff /* Data to be transmitted */
 750 #define UTX_TXDATA_SHIFT 0
 751 #define UTX_CTS_DELTA    0x0100 /* CTS changed */
 752 #define UTX_CTS_STAT     0x0200 /* CTS State */
 753 #define UTX_BUSY         0x0400 /* FIFO is busy, sending a character */
 754 #define UTX_NOCTS        0x0800 /* Ignore CTS */
 755 #define UTX_SEND_BREAK   0x1000 /* Send a BREAK */
 756 #define UTX_TX_AVAIL     0x2000 /* Transmit FIFO has a slot available */
 757 #define UTX_FIFO_HALF    0x4000 /* Transmit FIFO is half empty */
 758 #define UTX_FIFO_EMPTY   0x8000 /* Transmit FIFO is empty */
 759
 760 /* '328-compatible definitions */
 761 #define UTX_CTS_STATUS  UTX_CTS_STAT
 762 #define UTX_IGNORE_CTS  UTX_NOCTS
 763
 764 /*
 765  * UART Miscellaneous Register
 766  */
 767 #define UMISC_ADDR      0xfffff908
 768 #define UMISC           WORD_REF(UMISC_ADDR)
 769
 770 #define UMISC_TX_POL     0x0004 /* Transmit Polarity */
 771 #define UMISC_RX_POL     0x0008 /* Receive Polarity */
 772 #define UMISC_IRDA_LOOP  0x0010 /* IrDA Loopback Enable */
 773 #define UMISC_IRDA_EN    0x0020 /* Infra-Red Enable */
 774 #define UMISC_RTS        0x0040 /* Set RTS status */
 775 #define UMISC_RTSCONT    0x0080 /* Choose RTS control */
 776 #define UMISC_IR_TEST    0x0400 /* IRDA Test Enable */
 777 #define UMISC_BAUD_RESET 0x0800 /* Reset Baud Rate Generation Counters */
 778 #define UMISC_LOOP       0x1000 /* Serial Loopback Enable */
 779 #define UMISC_FORCE_PERR 0x2000 /* Force Parity Error */
 780 #define UMISC_CLKSRC     0x4000 /* Clock Source */
 781 #define UMISC_BAUD_TEST  0x8000 /* Enable Baud Test Mode */
 782
 783 /*
 784  * UART Non-integer Prescaler Register
 785  */
 786 #define NIPR_ADDR       0xfffff90a
 787 #define NIPR            WORD_REF(NIPR_ADDR)
 788
 789 #define NIPR_STEP_VALUE_MASK    0x00ff  /* NI prescaler step value */
 790 #define NIPR_STEP_VALUE_SHIFT   0
 791 #define NIPR_SELECT_MASK        0x0700  /* Tap Selection */
 792 #define NIPR_SELECT_SHIFT       8
 793 #define NIPR_PRE_SEL            0x8000  /* Non-integer prescaler select */
 794
 795
 796 /* generalization of uart control registers to support multiple ports: */
 797 typedef volatile struct {
 798   volatile unsigned short int ustcnt;
 799   volatile unsigned short int ubaud;
 800   union {
 801     volatile unsigned short int w;
 802     struct {
 803       volatile unsigned char status;
 804       volatile unsigned char rxdata;
 805     } b;
 806   } urx;
 807   union {
 808     volatile unsigned short int w;
 809     struct {
 810       volatile unsigned char status;
 811       volatile unsigned char txdata;
 812     } b;
 813   } utx;
 814   volatile unsigned short int umisc;
 815   volatile unsigned short int nipr;
 816   volatile unsigned short int pad1;
 817   volatile unsigned short int pad2;
 818 } __attribute__((packed)) m68328_uart;
 819
 820
 821 /**********
 822  *
 823  * 0xFFFFFAxx -- LCD Controller
 824  *
 825  **********/
 826
 827 /*
 828  * LCD Screen Starting Address Register
 829  */
 830 #define LSSA_ADDR       0xfffffa00
 831 #define LSSA            LONG_REF(LSSA_ADDR)
 832
 833 #define LSSA_SSA_MASK   0x1ffffffe      /* Bits 0 and 29-31 are reserved */
 834
 835 /*
 836  * LCD Virtual Page Width Register
 837  */
 838 #define LVPW_ADDR       0xfffffa05
 839 #define LVPW            BYTE_REF(LVPW_ADDR)
 840
 841 /*
 842  * LCD Screen Width Register (not compatible with '328 !!!)
 843  */
 844 #define LXMAX_ADDR      0xfffffa08
 845 #define LXMAX           WORD_REF(LXMAX_ADDR)
 846
 847 #define LXMAX_XM_MASK   0x02f0          /* Bits 0-3 and 10-15 are reserved */
 848
 849 /*
 850  * LCD Screen Height Register
 851  */
 852 #define LYMAX_ADDR      0xfffffa0a
 853 #define LYMAX           WORD_REF(LYMAX_ADDR)
 854
 855 #define LYMAX_YM_MASK   0x01ff          /* Bits 9-15 are reserved */
 856
 857 /*
 858  * LCD Cursor X Position Register
 859  */
 860 #define LCXP_ADDR       0xfffffa18
 861 #define LCXP            WORD_REF(LCXP_ADDR)
 862
 863 #define LCXP_CC_MASK    0xc000          /* Cursor Control */
 864 #define   LCXP_CC_TRAMSPARENT   0x0000
 865 #define   LCXP_CC_BLACK         0x4000
 866 #define   LCXP_CC_REVERSED      0x8000
 867 #define   LCXP_CC_WHITE         0xc000
 868 #define LCXP_CXP_MASK   0x02ff          /* Cursor X position */
 869
 870 /*
 871  * LCD Cursor Y Position Register
 872  */
 873 #define LCYP_ADDR       0xfffffa1a
 874 #define LCYP            WORD_REF(LCYP_ADDR)
 875
 876 #define LCYP_CYP_MASK   0x01ff          /* Cursor Y Position */
 877
 878 /*
 879  * LCD Cursor Width and Heigth Register
 880  */
 881 #define LCWCH_ADDR      0xfffffa1c
 882 #define LCWCH           WORD_REF(LCWCH_ADDR)
 883
 884 #define LCWCH_CH_MASK   0x001f          /* Cursor Height */
 885 #define LCWCH_CH_SHIFT  0
 886 #define LCWCH_CW_MASK   0x1f00          /* Cursor Width */
 887 #define LCWCH_CW_SHIFT  8
 888
 889 /*
 890  * LCD Blink Control Register
 891  */
 892 #define LBLKC_ADDR      0xfffffa1f
 893 #define LBLKC           BYTE_REF(LBLKC_ADDR)
 894
 895 #define LBLKC_BD_MASK   0x7f    /* Blink Divisor */
 896 #define LBLKC_BD_SHIFT  0
 897 #define LBLKC_BKEN      0x80    /* Blink Enabled */
 898
 899 /*
 900  * LCD Panel Interface Configuration Register
 901  */
 902 #define LPICF_ADDR      0xfffffa20
 903 #define LPICF           BYTE_REF(LPICF_ADDR)
 904
 905 #define LPICF_GS_MASK    0x03    /* Gray-Scale Mode */
 906 #define   LPICF_GS_BW      0x00
 907 #define   LPICF_GS_GRAY_4  0x01
 908 #define   LPICF_GS_GRAY_16 0x02
 909 #define LPICF_PBSIZ_MASK 0x0c   /* Panel Bus Width */
 910 #define   LPICF_PBSIZ_1    0x00
 911 #define   LPICF_PBSIZ_2    0x04
 912 #define   LPICF_PBSIZ_4    0x08
 913
 914 /*
 915  * LCD Polarity Configuration Register
 916  */
 917 #define LPOLCF_ADDR     0xfffffa21
 918 #define LPOLCF          BYTE_REF(LPOLCF_ADDR)
 919
 920 #define LPOLCF_PIXPOL   0x01    /* Pixel Polarity */
 921 #define LPOLCF_LPPOL    0x02    /* Line Pulse Polarity */
 922 #define LPOLCF_FLMPOL   0x04    /* Frame Marker Polarity */
 923 #define LPOLCF_LCKPOL   0x08    /* LCD Shift Lock Polarity */
 924
 925 /*
 926  * LACD (LCD Alternate Crystal Direction) Rate Control Register
 927  */
 928 #define LACDRC_ADDR     0xfffffa23
 929 #define LACDRC          BYTE_REF(LACDRC_ADDR)
 930
 931 #define LACDRC_ACDSLT    0x80   /* Signal Source Select */
 932 #define LACDRC_ACD_MASK  0x0f   /* Alternate Crystal Direction Control */
 933 #define LACDRC_ACD_SHIFT 0
 934
 935 /*
 936  * LCD Pixel Clock Divider Register
 937  */
 938 #define LPXCD_ADDR      0xfffffa25
 939 #define LPXCD           BYTE_REF(LPXCD_ADDR)
 940
 941 #define LPXCD_PCD_MASK  0x3f    /* Pixel Clock Divider */
 942 #define LPXCD_PCD_SHIFT 0
 943
 944 /*
 945  * LCD Clocking Control Register
 946  */
 947 #define LCKCON_ADDR     0xfffffa27
 948 #define LCKCON          BYTE_REF(LCKCON_ADDR)
 949
 950 #define LCKCON_DWS_MASK  0x0f   /* Display Wait-State */
 951 #define LCKCON_DWS_SHIFT 0
 952 #define LCKCON_DWIDTH    0x40   /* Display Memory Width  */
 953 #define LCKCON_LCDON     0x80   /* Enable LCD Controller */
 954
 955 /* '328-compatible definitions */
 956 #define LCKCON_DW_MASK  LCKCON_DWS_MASK
 957 #define LCKCON_DW_SHIFT LCKCON_DWS_SHIFT
 958
 959 /*
 960  * LCD Refresh Rate Adjustment Register
 961  */
 962 #define LRRA_ADDR       0xfffffa29
 963 #define LRRA            BYTE_REF(LRRA_ADDR)
 964
 965 /*
 966  * LCD Panning Offset Register
 967  */
 968 #define LPOSR_ADDR      0xfffffa2d
 969 #define LPOSR           BYTE_REF(LPOSR_ADDR)
 970
 971 #define LPOSR_POS_MASK  0x0f    /* Pixel Offset Code */
 972 #define LPOSR_POS_SHIFT 0
 973
 974 /*
 975  * LCD Frame Rate Control Modulation Register
 976  */
 977 #define LFRCM_ADDR      0xfffffa31
 978 #define LFRCM           BYTE_REF(LFRCM_ADDR)
 979
 980 #define LFRCM_YMOD_MASK  0x0f   /* Vertical Modulation */
 981 #define LFRCM_YMOD_SHIFT 0
 982 #define LFRCM_XMOD_MASK  0xf0   /* Horizontal Modulation */
 983 #define LFRCM_XMOD_SHIFT 4
 984
 985 /*
 986  * LCD Gray Palette Mapping Register
 987  */
 988 #define LGPMR_ADDR      0xfffffa33
 989 #define LGPMR           BYTE_REF(LGPMR_ADDR)
 990
 991 #define LGPMR_G1_MASK   0x0f
 992 #define LGPMR_G1_SHIFT  0
 993 #define LGPMR_G2_MASK   0xf0
 994 #define LGPMR_G2_SHIFT  4
 995
 996 /*
 997  * PWM Contrast Control Register
 998  */
 999 #define PWMR_ADDR       0xfffffa36
1000 #define PWMR            WORD_REF(PWMR_ADDR)
1001
1002 #define PWMR_PW_MASK    0x00ff  /* Pulse Width */
1003 #define PWMR_PW_SHIFT   0
1004 #define PWMR_CCPEN      0x0100  /* Contrast Control Enable */
1005 #define PWMR_SRC_MASK   0x0600  /* Input Clock Source */
1006 #define   PWMR_SRC_LINE   0x0000        /* Line Pulse  */
1007 #define   PWMR_SRC_PIXEL  0x0200        /* Pixel Clock */
1008 #define   PWMR_SRC_LCD    0x4000        /* LCD clock   */
1009
1010 /**********
1011  *
1012  * 0xFFFFFBxx -- Real-Time Clock (RTC)
1013  *
1014  **********/
1015
1016 /*
1017  * RTC Hours Minutes and Seconds Register
1018  */
1019 #define RTCTIME_ADDR    0xfffffb00
1020 #define RTCTIME         LONG_REF(RTCTIME_ADDR)
1021
1022 #define RTCTIME_SECONDS_MASK    0x0000003f      /* Seconds */
1023 #define RTCTIME_SECONDS_SHIFT   0
1024 #define RTCTIME_MINUTES_MASK    0x003f0000      /* Minutes */
1025 #define RTCTIME_MINUTES_SHIFT   16
1026 #define RTCTIME_HOURS_MASK      0x1f000000      /* Hours */
1027 #define RTCTIME_HOURS_SHIFT     24
1028
1029 /*
1030  *  RTC Alarm Register
1031  */
1032 #define RTCALRM_ADDR    0xfffffb04
1033 #define RTCALRM         LONG_REF(RTCALRM_ADDR)
1034
1035 #define RTCALRM_SECONDS_MASK    0x0000003f      /* Seconds */
1036 #define RTCALRM_SECONDS_SHIFT   0
1037 #define RTCALRM_MINUTES_MASK    0x003f0000      /* Minutes */
1038 #define RTCALRM_MINUTES_SHIFT   16
1039 #define RTCALRM_HOURS_MASK      0x1f000000      /* Hours */
1040 #define RTCALRM_HOURS_SHIFT     24
1041
1042 /*
1043  * Watchdog Timer Register
1044  */
1045 #define WATCHDOG_ADDR   0xfffffb0a
1046 #define WATCHDOG        WORD_REF(WATCHDOG_ADDR)
1047
1048 #define WATCHDOG_EN     0x0001  /* Watchdog Enabled */
1049 #define WATCHDOG_ISEL   0x0002  /* Select the watchdog interrupt */
1050 #define WATCHDOG_INTF   0x0080  /* Watchdog interrupt occcured */
1051 #define WATCHDOG_CNT_MASK  0x0300       /* Watchdog Counter */
1052 #define WATCHDOG_CNT_SHIFT 8
1053
1054 /*
1055  * RTC Control Register
1056  */
1057 #define RTCCTL_ADDR     0xfffffb0c
1058 #define RTCCTL          WORD_REF(RTCCTL_ADDR)
1059
1060 #define RTCCTL_XTL      0x0020  /* Crystal Selection */
1061 #define RTCCTL_EN       0x0080  /* RTC Enable */
1062
1063 /* '328-compatible definitions */
1064 #define RTCCTL_384      RTCCTL_XTL
1065 #define RTCCTL_ENABLE   RTCCTL_EN
1066
1067 /*
1068  * RTC Interrupt Status Register
1069  */
1070 #define RTCISR_ADDR     0xfffffb0e
1071 #define RTCISR          WORD_REF(RTCISR_ADDR)
1072
1073 #define RTCISR_SW       0x0001  /* Stopwatch timed out */
1074 #define RTCISR_MIN      0x0002  /* 1-minute interrupt has occurred */
1075 #define RTCISR_ALM      0x0004  /* Alarm interrupt has occurred */
1076 #define RTCISR_DAY      0x0008  /* 24-hour rollover interrupt has occurred */
1077 #define RTCISR_1HZ      0x0010  /* 1Hz interrupt has occurred */
1078 #define RTCISR_HR       0x0020  /* 1-hour interrupt has occurred */
1079 #define RTCISR_SAM0     0x0100  /*   4Hz /   4.6875Hz interrupt has occurred */
1080 #define RTCISR_SAM1     0x0200  /*   8Hz /   9.3750Hz interrupt has occurred */
1081 #define RTCISR_SAM2     0x0400  /*  16Hz /  18.7500Hz interrupt has occurred */
1082 #define RTCISR_SAM3     0x0800  /*  32Hz /  37.5000Hz interrupt has occurred */
1083 #define RTCISR_SAM4     0x1000  /*  64Hz /  75.0000Hz interrupt has occurred */
1084 #define RTCISR_SAM5     0x2000  /* 128Hz / 150.0000Hz interrupt has occurred */
1085 #define RTCISR_SAM6     0x4000  /* 256Hz / 300.0000Hz interrupt has occurred */
1086 #define RTCISR_SAM7     0x8000  /* 512Hz / 600.0000Hz interrupt has occurred */
1087
1088 /*
1089  * RTC Interrupt Enable Register
1090  */
1091 #define RTCIENR_ADDR    0xfffffb10
1092 #define RTCIENR         WORD_REF(RTCIENR_ADDR)
1093
1094 #define RTCIENR_SW      0x0001  /* Stopwatch interrupt enable */
1095 #define RTCIENR_MIN     0x0002  /* 1-minute interrupt enable */
1096 #define RTCIENR_ALM     0x0004  /* Alarm interrupt enable */
1097 #define RTCIENR_DAY     0x0008  /* 24-hour rollover interrupt enable */
1098 #define RTCIENR_1HZ     0x0010  /* 1Hz interrupt enable */
1099 #define RTCIENR_HR      0x0020  /* 1-hour interrupt enable */
1100 #define RTCIENR_SAM0    0x0100  /*   4Hz /   4.6875Hz interrupt enable */
1101 #define RTCIENR_SAM1    0x0200  /*   8Hz /   9.3750Hz interrupt enable */
1102 #define RTCIENR_SAM2    0x0400  /*  16Hz /  18.7500Hz interrupt enable */
1103 #define RTCIENR_SAM3    0x0800  /*  32Hz /  37.5000Hz interrupt enable */
1104 #define RTCIENR_SAM4    0x1000  /*  64Hz /  75.0000Hz interrupt enable */
1105 #define RTCIENR_SAM5    0x2000  /* 128Hz / 150.0000Hz interrupt enable */
1106 #define RTCIENR_SAM6    0x4000  /* 256Hz / 300.0000Hz interrupt enable */
1107 #define RTCIENR_SAM7    0x8000  /* 512Hz / 600.0000Hz interrupt enable */
1108
1109 /*
1110  * Stopwatch Minutes Register
1111  */
1112 #define STPWCH_ADDR     0xfffffb12
1113 #define STPWCH          WORD_REF(STPWCH)
1114
1115 #define STPWCH_CNT_MASK  0x003f /* Stopwatch countdown value */
1116 #define SPTWCH_CNT_SHIFT 0
1117
1118 /*
1119  * RTC Day Count Register
1120  */
1121 #define DAYR_ADDR       0xfffffb1a
1122 #define DAYR            WORD_REF(DAYR_ADDR)
1123
1124 #define DAYR_DAYS_MASK  0x1ff   /* Day Setting */
1125 #define DAYR_DAYS_SHIFT 0
1126
1127 /*
1128  * RTC Day Alarm Register
1129  */
1130 #define DAYALARM_ADDR   0xfffffb1c
1131 #define DAYALARM        WORD_REF(DAYALARM_ADDR)
1132
1133 #define DAYALARM_DAYSAL_MASK    0x01ff  /* Day Setting of the Alarm */
1134 #define DAYALARM_DAYSAL_SHIFT   0
1135
1136 /**********
1137  *
1138  * 0xFFFFFCxx -- DRAM Controller
1139  *
1140  **********/
1141
1142 /*
1143  * DRAM Memory Configuration Register
1144  */
1145 #define DRAMMC_ADDR     0xfffffc00
1146 #define DRAMMC          WORD_REF(DRAMMC_ADDR)
1147
1148 #define DRAMMC_ROW12_MASK       0xc000  /* Row address bit for MD12 */
1149 #define   DRAMMC_ROW12_PA10     0x0000
1150 #define   DRAMMC_ROW12_PA21     0x4000
1151 #define   DRAMMC_ROW12_PA23     0x8000
1152 #define DRAMMC_ROW0_MASK        0x3000  /* Row address bit for MD0 */
1153 #define   DRAMMC_ROW0_PA11      0x0000
1154 #define   DRAMMC_ROW0_PA22      0x1000
1155 #define   DRAMMC_ROW0_PA23      0x2000
1156 #define DRAMMC_ROW11            0x0800  /* Row address bit for MD11 PA20/PA22 */
1157 #define DRAMMC_ROW10            0x0400  /* Row address bit for MD10 PA19/PA21 */
1158 #define DRAMMC_ROW9             0x0200  /* Row address bit for MD9  PA9/PA19  */
1159 #define DRAMMC_ROW8             0x0100  /* Row address bit for MD8  PA10/PA20 */
1160 #define DRAMMC_COL10            0x0080  /* Col address bit for MD10 PA11/PA0  */
1161 #define DRAMMC_COL9             0x0040  /* Col address bit for MD9  PA10/PA0  */
1162 #define DRAMMC_COL8             0x0020  /* Col address bit for MD8  PA9/PA0   */
1163 #define DRAMMC_REF_MASK         0x001f  /* Reresh Cycle */
1164 #define DRAMMC_REF_SHIFT        0
1165
1166 /*
1167  * DRAM Control Register
1168  */
1169 #define DRAMC_ADDR      0xfffffc02
1170 #define DRAMC           WORD_REF(DRAMC_ADDR)
1171
1172 #define DRAMC_DWE          0x0001       /* DRAM Write Enable */
1173 #define DRAMC_RST          0x0002       /* Reset Burst Refresh Enable */
1174 #define DRAMC_LPR          0x0004       /* Low-Power Refresh Enable */
1175 #define DRAMC_SLW          0x0008       /* Slow RAM */
1176 #define DRAMC_LSP          0x0010       /* Light Sleep */
1177 #define DRAMC_MSW          0x0020       /* Slow Multiplexing */
1178 #define DRAMC_WS_MASK      0x00c0       /* Wait-states */
1179 #define DRAMC_WS_SHIFT     6
1180 #define DRAMC_PGSZ_MASK    0x0300       /* Page Size for fast page mode */
1181 #define DRAMC_PGSZ_SHIFT   8
1182 #define   DRAMC_PGSZ_256K  0x0000
1183 #define   DRAMC_PGSZ_512K  0x0100
1184 #define   DRAMC_PGSZ_1024K 0x0200
1185 #define   DRAMC_PGSZ_2048K 0x0300
1186 #define DRAMC_EDO          0x0400       /* EDO DRAM */
1187 #define DRAMC_CLK          0x0800       /* Refresh Timer Clock source select */
1188 #define DRAMC_BC_MASK      0x3000       /* Page Access Clock Cycle (FP mode) */
1189 #define DRAMC_BC_SHIFT     12
1190 #define DRAMC_RM           0x4000       /* Refresh Mode */
1191 #define DRAMC_EN           0x8000       /* DRAM Controller enable */
1192
1193
1194 /**********
1195  *
1196  * 0xFFFFFDxx -- In-Circuit Emulation (ICE)
1197  *
1198  **********/
1199
1200 /*
1201  * ICE Module Address Compare Register
1202  */
1203 #define ICEMACR_ADDR    0xfffffd00
1204 #define ICEMACR         LONG_REF(ICEMACR_ADDR)
1205
1206 /*
1207  * ICE Module Address Mask Register
1208  */
1209 #define ICEMAMR_ADDR    0xfffffd04
1210 #define ICEMAMR         LONG_REF(ICEMAMR_ADDR)
1211
1212 /*
1213  * ICE Module Control Compare Register
1214  */
1215 #define ICEMCCR_ADDR    0xfffffd08
1216 #define ICEMCCR         WORD_REF(ICEMCCR_ADDR)
1217
1218 #define ICEMCCR_PD      0x0001  /* Program/Data Cycle Selection */
1219 #define ICEMCCR_RW      0x0002  /* Read/Write Cycle Selection */
1220
1221 /*
1222  * ICE Module Control Mask Register
1223  */
1224 #define ICEMCMR_ADDR    0xfffffd0a
1225 #define ICEMCMR         WORD_REF(ICEMCMR_ADDR)
1226
1227 #define ICEMCMR_PDM     0x0001  /* Program/Data Cycle Mask */
1228 #define ICEMCMR_RWM     0x0002  /* Read/Write Cycle Mask */
1229
1230 /*
1231  * ICE Module Control Register
1232  */
1233 #define ICEMCR_ADDR     0xfffffd0c
1234 #define ICEMCR          WORD_REF(ICEMCR_ADDR)
1235
1236 #define ICEMCR_CEN      0x0001  /* Compare Enable */
1237 #define ICEMCR_PBEN     0x0002  /* Program Break Enable */
1238 #define ICEMCR_SB       0x0004  /* Single Breakpoint */
1239 #define ICEMCR_HMDIS    0x0008  /* HardMap disable */
1240 #define ICEMCR_BBIEN    0x0010  /* Bus Break Interrupt Enable */
1241
1242 /*
1243  * ICE Module Status Register
1244  */
1245 #define ICEMSR_ADDR     0xfffffd0e
1246 #define ICEMSR          WORD_REF(ICEMSR_ADDR)
1247
1248 #define ICEMSR_EMUEN    0x0001  /* Emulation Enable */
1249 #define ICEMSR_BRKIRQ   0x0002  /* A-Line Vector Fetch Detected */
1250 #define ICEMSR_BBIRQ    0x0004  /* Bus Break Interrupt Detected */
1251 #define ICEMSR_EMIRQ    0x0008  /* EMUIRQ Falling Edge Detected */
1252
1253 #endif /* _MC68EZ328_H_ */