include/asm-m68k/apollodma.h

   1 /*
   2  * linux/include/asm/dma.h: Defines for using and allocating dma channels.
   3  * Written by Hennus Bergman, 1992.
   4  * High DMA channel support & info by Hannu Savolainen
   5  * and John Boyd, Nov. 1992.
   6  */
   7
   8 #ifndef _ASM_APOLLO_DMA_H
   9 #define _ASM_APOLLO_DMA_H
  10
  11 #include <asm/apollohw.h>               /* need byte IO */
  12 #include <linux/spinlock.h>             /* And spinlocks */
  13 #include <linux/delay.h>
  14
  15
  16 #define dma_outb(val,addr) (*((volatile unsigned char *)(addr+IO_BASE)) = (val))
  17 #define dma_inb(addr)      (*((volatile unsigned char *)(addr+IO_BASE)))
  18
  19 /*
  20  * NOTES about DMA transfers:
  21  *
  22  *  controller 1: channels 0-3, byte operations, ports 00-1F
  23  *  controller 2: channels 4-7, word operations, ports C0-DF
  24  *
  25  *  - ALL registers are 8 bits only, regardless of transfer size
  26  *  - channel 4 is not used - cascades 1 into 2.
  27  *  - channels 0-3 are byte - addresses/counts are for physical bytes
  28  *  - channels 5-7 are word - addresses/counts are for physical words
  29  *  - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries
  30  *  - transfer count loaded to registers is 1 less than actual count
  31  *  - controller 2 offsets are all even (2x offsets for controller 1)
  32  *  - page registers for 5-7 don't use data bit 0, represent 128K pages
  33  *  - page registers for 0-3 use bit 0, represent 64K pages
  34  *
  35  * DMA transfers are limited to the lower 16MB of _physical_ memory.
  36  * Note that addresses loaded into registers must be _physical_ addresses,
  37  * not logical addresses (which may differ if paging is active).
  38  *
  39  *  Address mapping for channels 0-3:
  40  *
  41  *   A23 ... A16 A15 ... A8  A7 ... A0    (Physical addresses)
  42  *    |  ...  |   |  ... |   |  ... |
  43  *    |  ...  |   |  ... |   |  ... |
  44  *    |  ...  |   |  ... |   |  ... |
  45  *   P7  ...  P0  A7 ... A0  A7 ... A0
  46  * |    Page    | Addr MSB | Addr LSB |   (DMA registers)
  47  *
  48  *  Address mapping for channels 5-7:
  49  *
  50  *   A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0    (Physical addresses)
  51  *    |  ...  |   \   \   ... \  \  \  ... \  \
  52  *    |  ...  |    \   \   ... \  \  \  ... \  (not used)
  53  *    |  ...  |     \   \   ... \  \  \  ... \
  54  *   P7  ...  P1 (0) A7 A6  ... A0 A7 A6 ... A0
  55  * |      Page      |  Addr MSB   |  Addr LSB  |   (DMA registers)
  56  *
  57  * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses
  58  * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at
  59  * the hardware level, so odd-byte transfers aren't possible).
  60  *
  61  * Transfer count (_not # bytes_) is limited to 64K, represented as actual
  62  * count - 1 : 64K => 0xFFFF, 1 => 0x0000.  Thus, count is always 1 or more,
  63  * and up to 128K bytes may be transferred on channels 5-7 in one operation.
  64  *
  65  */
  66
  67 #define MAX_DMA_CHANNELS        8
  68
  69 /* The maximum address that we can perform a DMA transfer to on this platform */#define MAX_DMA_ADDRESS      (PAGE_OFFSET+0x1000000)
  70
  71 /* 8237 DMA controllers */
  72 #define IO_DMA1_BASE    0x10C00 /* 8 bit slave DMA, channels 0..3 */
  73 #define IO_DMA2_BASE    0x10D00 /* 16 bit master DMA, ch 4(=slave input)..7 */
  74
  75 /* DMA controller registers */
  76 #define DMA1_CMD_REG            (IO_DMA1_BASE+0x08) /* command register (w) */
  77 #define DMA1_STAT_REG           (IO_DMA1_BASE+0x08) /* status register (r) */
  78 #define DMA1_REQ_REG            (IO_DMA1_BASE+0x09) /* request register (w) */
  79 #define DMA1_MASK_REG           (IO_DMA1_BASE+0x0A) /* single-channel mask (w) */
  80 #define DMA1_MODE_REG           (IO_DMA1_BASE+0x0B) /* mode register (w) */
  81 #define DMA1_CLEAR_FF_REG       (IO_DMA1_BASE+0x0C) /* clear pointer flip-flop (w) */
  82 #define DMA1_TEMP_REG           (IO_DMA1_BASE+0x0D) /* Temporary Register (r) */
  83 #define DMA1_RESET_REG          (IO_DMA1_BASE+0x0D) /* Master Clear (w) */
  84 #define DMA1_CLR_MASK_REG       (IO_DMA1_BASE+0x0E) /* Clear Mask */
  85 #define DMA1_MASK_ALL_REG       (IO_DMA1_BASE+0x0F) /* all-channels mask (w) */
  86
  87 #define DMA2_CMD_REG            (IO_DMA2_BASE+0x10) /* command register (w) */
  88 #define DMA2_STAT_REG           (IO_DMA2_BASE+0x10) /* status register (r) */
  89 #define DMA2_REQ_REG            (IO_DMA2_BASE+0x12) /* request register (w) */
  90 #define DMA2_MASK_REG           (IO_DMA2_BASE+0x14) /* single-channel mask (w) */
  91 #define DMA2_MODE_REG           (IO_DMA2_BASE+0x16) /* mode register (w) */
  92 #define DMA2_CLEAR_FF_REG       (IO_DMA2_BASE+0x18) /* clear pointer flip-flop (w) */
  93 #define DMA2_TEMP_REG           (IO_DMA2_BASE+0x1A) /* Temporary Register (r) */
  94 #define DMA2_RESET_REG          (IO_DMA2_BASE+0x1A) /* Master Clear (w) */
  95 #define DMA2_CLR_MASK_REG       (IO_DMA2_BASE+0x1C) /* Clear Mask */
  96 #define DMA2_MASK_ALL_REG       (IO_DMA2_BASE+0x1E) /* all-channels mask (w) */
  97
  98 #define DMA_ADDR_0              (IO_DMA1_BASE+0x00) /* DMA address registers */
  99 #define DMA_ADDR_1              (IO_DMA1_BASE+0x02)
 100 #define DMA_ADDR_2              (IO_DMA1_BASE+0x04)
 101 #define DMA_ADDR_3              (IO_DMA1_BASE+0x06)
 102 #define DMA_ADDR_4              (IO_DMA2_BASE+0x00)
 103 #define DMA_ADDR_5              (IO_DMA2_BASE+0x04)
 104 #define DMA_ADDR_6              (IO_DMA2_BASE+0x08)
 105 #define DMA_ADDR_7              (IO_DMA2_BASE+0x0C)
 106
 107 #define DMA_CNT_0               (IO_DMA1_BASE+0x01)   /* DMA count registers */
 108 #define DMA_CNT_1               (IO_DMA1_BASE+0x03)
 109 #define DMA_CNT_2               (IO_DMA1_BASE+0x05)
 110 #define DMA_CNT_3               (IO_DMA1_BASE+0x07)
 111 #define DMA_CNT_4               (IO_DMA2_BASE+0x02)
 112 #define DMA_CNT_5               (IO_DMA2_BASE+0x06)
 113 #define DMA_CNT_6               (IO_DMA2_BASE+0x0A)
 114 #define DMA_CNT_7               (IO_DMA2_BASE+0x0E)
 115
 116 #define DMA_MODE_READ   0x44    /* I/O to memory, no autoinit, increment, single mode */
 117 #define DMA_MODE_WRITE  0x48    /* memory to I/O, no autoinit, increment, single mode */
 118 #define DMA_MODE_CASCADE 0xC0   /* pass thru DREQ->HRQ, DACK<-HLDA only */
 119
 120 #define DMA_AUTOINIT    0x10
 121
 122 #define DMA_8BIT 0
 123 #define DMA_16BIT 1
 124 #define DMA_BUSMASTER 2
 125
 126 extern spinlock_t  dma_spin_lock;
 127
 128 static __inline__ unsigned long claim_dma_lock(void)
 129 {
 130         unsigned long flags;
 131         spin_lock_irqsave(&dma_spin_lock, flags);
 132         return flags;
 133 }
 134
 135 static __inline__ void release_dma_lock(unsigned long flags)
 136 {
 137         spin_unlock_irqrestore(&dma_spin_lock, flags);
 138 }
 139
 140 /* enable/disable a specific DMA channel */
 141 static __inline__ void enable_dma(unsigned int dmanr)
 142 {
 143         if (dmanr<=3)
 144                 dma_outb(dmanr,  DMA1_MASK_REG);
 145         else
 146                 dma_outb(dmanr & 3,  DMA2_MASK_REG);
 147 }
 148
 149 static __inline__ void disable_dma(unsigned int dmanr)
 150 {
 151         if (dmanr<=3)
 152                 dma_outb(dmanr | 4,  DMA1_MASK_REG);
 153         else
 154                 dma_outb((dmanr & 3) | 4,  DMA2_MASK_REG);
 155 }
 156
 157 /* Clear the 'DMA Pointer Flip Flop'.
 158  * Write 0 for LSB/MSB, 1 for MSB/LSB access.
 159  * Use this once to initialize the FF to a known state.
 160  * After that, keep track of it. :-)
 161  * --- In order to do that, the DMA routines below should ---
 162  * --- only be used while holding the DMA lock ! ---
 163  */
 164 static __inline__ void clear_dma_ff(unsigned int dmanr)
 165 {
 166         if (dmanr<=3)
 167                 dma_outb(0,  DMA1_CLEAR_FF_REG);
 168         else
 169                 dma_outb(0,  DMA2_CLEAR_FF_REG);
 170 }
 171
 172 /* set mode (above) for a specific DMA channel */
 173 static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
 174 {
 175         if (dmanr<=3)
 176                 dma_outb(mode | dmanr,  DMA1_MODE_REG);
 177         else
 178                 dma_outb(mode | (dmanr&3),  DMA2_MODE_REG);
 179 }
 180
 181 /* Set transfer address & page bits for specific DMA channel.
 182  * Assumes dma flipflop is clear.
 183  */
 184 static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
 185 {
 186         if (dmanr <= 3)  {
 187             dma_outb( a & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
 188             dma_outb( (a>>8) & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
 189         }  else  {
 190             dma_outb( (a>>1) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
 191             dma_outb( (a>>9) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
 192         }
 193 }
 194
 195
 196 /* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for
 197  * a specific DMA channel.
 198  * You must ensure the parameters are valid.
 199  * NOTE: from a manual: "the number of transfers is one more
 200  * than the initial word count"! This is taken into account.
 201  * Assumes dma flip-flop is clear.
 202  * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
 203  */
 204 static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
 205 {
 206         count--;
 207         if (dmanr <= 3)  {
 208             dma_outb( count & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
 209             dma_outb( (count>>8) & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
 210         } else {
 211             dma_outb( (count>>1) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
 212             dma_outb( (count>>9) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
 213         }
 214 }
 215
 216
 217 /* Get DMA residue count. After a DMA transfer, this
 218  * should return zero. Reading this while a DMA transfer is
 219  * still in progress will return unpredictable results.
 220  * If called before the channel has been used, it may return 1.
 221  * Otherwise, it returns the number of _bytes_ left to transfer.
 222  *
 223  * Assumes DMA flip-flop is clear.
 224  */
 225 static __inline__ int get_dma_residue(unsigned int dmanr)
 226 {
 227         unsigned int io_port = (dmanr<=3)? ((dmanr&3)<<1) + 1 + IO_DMA1_BASE
 228                                          : ((dmanr&3)<<2) + 2 + IO_DMA2_BASE;
 229
 230         /* using short to get 16-bit wrap around */
 231         unsigned short count;
 232
 233         count = 1 + dma_inb(io_port);
 234         count += dma_inb(io_port) << 8;
 235
 236         return (dmanr<=3)? count : (count<<1);
 237 }
 238
 239
 240 /* These are in kernel/dma.c: */
 241 extern int request_dma(unsigned int dmanr, const char * device_id);     /* reserve a DMA channel */
 242 extern void free_dma(unsigned int dmanr);       /* release it again */
 243
 244 /* These are in arch/m68k/apollo/dma.c: */
 245 extern unsigned short dma_map_page(unsigned long phys_addr,int count,int type);
 246 extern void dma_unmap_page(unsigned short dma_addr);
 247
 248 #endif /* _ASM_APOLLO_DMA_H */