ACPI: add support for Smart Battery
[linux-2.6/linux-acpi-2.6/ibm-acpi-2.6.git] / drivers / net / dgrs_i82596.h
blobc7a38c16a00be7f954a2341c79b9b6a813e90f3f
1 /*
2 * i82596 ethernet controller bits and structures (little endian)
4 * $Id: i82596.h,v 1.8 1996/09/03 11:19:03 rick Exp $
5 */
7 /************************************************************************/
8 /* */
9 /* PORT commands (p. 4-20). The least significant nibble is one */
10 /* of these commands, the rest of the command is a memory address */
11 /* aligned on a 16 byte boundary. Note that port commands must */
12 /* be written to the PORT address and the PORT address+2 with two */
13 /* halfword writes. Write the LSH first to PORT, then the MSH to */
14 /* PORT+2. Blame Intel. */
15 /* */
16 /************************************************************************/
17 #define I596_PORT_RESET 0x0 /* Reset. Wait 5 SysClks & 10 TxClks */
18 #define I596_PORT_SELFTEST 0x1 /* Do a selftest */
19 #define I596_PORT_SCP_ADDR 0x2 /* Set new SCP address */
20 #define I596_PORT_DUMP 0x3 /* Dump internal data structures */
23 * I596_ST: Selftest results (p. 4-21)
25 typedef volatile struct
27 ulong signature; /* ROM checksum */
28 ulong result; /* Selftest results: non-zero is a failure */
29 } I596_ST;
31 #define I596_ST_SELFTEST_FAIL 0x1000 /* Selftest Failed */
32 #define I596_ST_DIAGNOSE_FAIL 0x0020 /* Diagnose Failed */
33 #define I596_ST_BUSTIMER_FAIL 0x0010 /* Bus Timer Failed */
34 #define I596_ST_REGISTER_FAIL 0x0008 /* Register Failed */
35 #define I596_ST_ROM_FAIL 0x0004 /* ROM Failed */
38 * I596_DUMP: Dump results
40 typedef volatile struct
42 ulong dump[77];
43 } I596_DUMP;
45 /************************************************************************/
46 /* */
47 /* I596_TBD: Transmit Buffer Descriptor (p. 4-59) */
48 /* */
49 /************************************************************************/
50 typedef volatile struct _I596_TBD
52 ulong count;
53 vol struct _I596_TBD *next;
54 uchar *buf;
55 ushort unused1;
56 ushort unused2;
57 } I596_TBD;
59 #define I596_TBD_NOLINK ((I596_TBD *) 0xffffffff)
60 #define I596_TBD_EOF 0x8000
61 #define I596_TBD_COUNT_MASK 0x3fff
63 /************************************************************************/
64 /* */
65 /* I596_TFD: Transmit Frame Descriptor (p. 4-56) */
66 /* a.k.a. I596_CB_XMIT */
67 /* */
68 /************************************************************************/
69 typedef volatile struct
71 ushort status;
72 ushort cmd;
73 union _I596_CB *next;
74 I596_TBD *tbdp;
75 ulong count; /* for speed */
77 /* Application defined data follows structure... */
79 #if 0 /* We don't use these intel defined ones */
80 uchar addr[6];
81 ushort len;
82 uchar data[1];
83 #else
84 ulong dstchan;/* Used by multi-NIC mode */
85 #endif
86 } I596_TFD;
88 #define I596_TFD_NOCRC 0x0010 /* cmd: No CRC insertion */
89 #define I596_TFD_FLEX 0x0008 /* cmd: Flexible mode */
91 /************************************************************************/
92 /* */
93 /* I596_RBD: Receive Buffer Descriptor (p. 4-84) */
94 /* */
95 /************************************************************************/
96 typedef volatile struct _I596_RBD
98 #ifdef INTEL_RETENTIVE
99 ushort count; /* Length of data in buf */
100 ushort offset;
101 #else
102 ulong count; /* Length of data in buf */
103 #endif
104 vol struct _I596_RBD *next; /* Next buffer descriptor in list */
105 uchar *buf; /* Data buffer */
106 #ifdef INTEL_RETENTIVE
107 ushort size; /* Size of buf (constant) */
108 ushort zero;
109 #else
110 ulong size; /* Size of buf (constant) */
111 #endif
113 /* Application defined data follows structure... */
115 uchar chan;
116 uchar refcnt;
117 ushort len;
118 } I596_RBD;
120 #define I596_RBD_NOLINK ((I596_RBD *) 0xffffffff)
121 #define I596_RBD_EOF 0x8000 /* This is last buffer in a frame */
122 #define I596_RBD_F 0x4000 /* The actual count is valid */
124 #define I596_RBD_EL 0x8000 /* Last buffer in list */
126 /************************************************************************/
127 /* */
128 /* I596_RFD: Receive Frame Descriptor (p. 4-79) */
129 /* */
130 /************************************************************************/
131 typedef volatile struct _I596_RFD
133 ushort status;
134 ushort cmd;
135 vol struct _I596_RFD *next;
136 vol struct _I596_RBD *rbdp;
137 ushort count; /* Len of data in RFD: always 0 */
138 ushort size; /* Size of RFD buffer: always 0 */
140 /* Application defined data follows structure... */
142 # if 0 /* We don't use these intel defined ones */
143 uchar addr[6];
144 ushort len;
145 uchar data[1];
146 # else
147 ulong dstchan;/* Used by multi-nic mode */
148 # endif
149 } I596_RFD;
151 #define I596_RFD_C 0x8000 /* status: frame complete */
152 #define I596_RFD_B 0x4000 /* status: frame busy or waiting */
153 #define I596_RFD_OK 0x2000 /* status: frame OK */
154 #define I596_RFD_ERR_LENGTH 0x1000 /* status: length error */
155 #define I596_RFD_ERR_CRC 0x0800 /* status: CRC error */
156 #define I596_RFD_ERR_ALIGN 0x0400 /* status: alignment error */
157 #define I596_RFD_ERR_NOBUFS 0x0200 /* status: resource error */
158 #define I596_RFD_ERR_DMA 0x0100 /* status: DMA error */
159 #define I596_RFD_ERR_SHORT 0x0080 /* status: too short error */
160 #define I596_RFD_NOMATCH 0x0002 /* status: IA was not matched */
161 #define I596_RFD_COLLISION 0x0001 /* status: collision during receive */
163 #define I596_RFD_EL 0x8000 /* cmd: end of RFD list */
164 #define I596_RFD_FLEX 0x0008 /* cmd: Flexible mode */
165 #define I596_RFD_EOF 0x8000 /* count: last buffer in the frame */
166 #define I596_RFD_F 0x4000 /* count: The actual count is valid */
168 /************************************************************************/
169 /* */
170 /* Commands */
171 /* */
172 /************************************************************************/
174 /* values for cmd halfword in all the structs below */
175 #define I596_CB_CMD 0x07 /* CB COMMANDS */
176 #define I596_CB_CMD_NOP 0
177 #define I596_CB_CMD_IA 1
178 #define I596_CB_CMD_CONF 2
179 #define I596_CB_CMD_MCAST 3
180 #define I596_CB_CMD_XMIT 4
181 #define I596_CB_CMD_TDR 5
182 #define I596_CB_CMD_DUMP 6
183 #define I596_CB_CMD_DIAG 7
185 #define I596_CB_CMD_EL 0x8000 /* CB is last in linked list */
186 #define I596_CB_CMD_S 0x4000 /* Suspend after execution */
187 #define I596_CB_CMD_I 0x2000 /* cause interrupt */
189 /* values for the status halfword in all the struct below */
190 #define I596_CB_STATUS 0xF000 /* All four status bits */
191 #define I596_CB_STATUS_C 0x8000 /* Command complete */
192 #define I596_CB_STATUS_B 0x4000 /* Command busy executing */
193 #define I596_CB_STATUS_C_OR_B 0xC000 /* Command complete or busy */
194 #define I596_CB_STATUS_OK 0x2000 /* Command complete, no errors */
195 #define I596_CB_STATUS_A 0x1000 /* Command busy executing */
197 #define I596_CB_NOLINK ((I596_CB *) 0xffffffff)
200 * I596_CB_NOP: NOP Command (p. 4-34)
202 typedef volatile struct
204 ushort status;
205 ushort cmd;
206 union _I596_CB *next;
207 } I596_CB_NOP;
210 * Same as above, but command and status in one ulong for speed
212 typedef volatile struct
214 ulong csr;
215 union _I596_CB *next;
216 } I596_CB_FAST;
217 #define FASTs(X) (X)
218 #define FASTc(X) ((X)<<16)
221 * I596_CB_IA: Individual (MAC) Address Command (p. 4-35)
223 typedef volatile struct
225 ushort status;
226 ushort cmd;
227 union _I596_CB *next;
228 uchar addr[6];
229 } I596_CB_IA;
232 * I596_CB_CONF: Configure Command (p. 4-37)
234 typedef volatile struct
236 ushort status;
237 ushort cmd;
238 union _I596_CB *next;
239 uchar conf[14];
240 } I596_CB_CONF;
242 #define I596_CONF0_P 0x80 /* Enable RBD Prefetch Bit */
243 #define I596_CONF0_COUNT 14 /* Count of configuration bytes */
245 #define I596_CONF1_MON_OFF 0xC0 /* Monitor mode: Monitor off */
246 #define I596_CONF1_MON_ON 0x80 /* Monitor mode: Monitor on */
247 #define I596_CONF1_TxFIFO(W) (W) /* TxFIFO trigger, in words */
249 #define I596_CONF2_SAVEBF 0x80 /* Save bad frames */
251 #define I596_CONF3_ADDRLEN(B) (B) /* Address length */
252 #define I596_CONF3_NOSRCINSERT 0x08 /* Do not insert source address */
253 #define I596_CONF3_PREAMBLE8 0x20 /* 8 byte preamble */
254 #define I596_CONF3_LOOPOFF 0x00 /* Loopback: Off */
255 #define I596_CONF3_LOOPINT 0x40 /* Loopback: internal */
256 #define I596_CONF3_LOOPEXT 0xC0 /* Loopback: external */
258 #define I596_CONF4_LINPRI(ST) (ST) /* Linear priority: slot times */
259 #define I596_CONF4_EXPPRI(ST) (ST) /* Exponential priority: slot times */
260 #define I596_CONF4_IEEE_BOM 0 /* IEEE 802.3 backoff method */
262 #define I596_CONF5_IFS(X) (X) /* Interframe spacing in clocks */
264 #define I596_CONF6_ST_LOW(X) (X&255) /* Slot time, low byte */
266 #define I596_CONF7_ST_HI(X) (X>>8) /* Slot time, high bits */
267 #define I596_CONF7_RETRY(X) (X<<4) /* Max retry number */
269 #define I596_CONF8_PROMISC 0x01 /* Rcv all frames */
270 #define I596_CONF8_NOBROAD 0x02
271 #define I596_CONF8_MANCHESTER 0x04
272 #define I596_CONF8_TxNOCRS 0x08
273 #define I596_CONF8_NOCRC 0x10
274 #define I596_CONF8_CRC_CCITT 0x20
275 #define I596_CONF8_BITSTUFFING 0x40
276 #define I596_CONF8_PADDING 0x80
278 #define I596_CONF9_CSFILTER(X) (X)
279 #define I596_CONF9_CSINT(X) 0x08
280 #define I596_CONF9_CDFILTER(X) (X<<4)
281 #define I596_CONF9_CDINT(X) 0x80
283 #define I596_CONF10_MINLEN(X) (X) /* Minimum frame length */
285 #define I596_CONF11_PRECRS_ 0x01 /* Preamble before carrier sense */
286 #define I596_CONF11_LNGFLD_ 0x02 /* Padding in End of Carrier */
287 #define I596_CONF11_CRCINM_ 0x04 /* CRC in memory */
288 #define I596_CONF11_AUTOTX 0x08 /* Auto retransmit */
289 #define I596_CONF11_CSBSAC_ 0x10 /* Collision detect by src addr cmp. */
290 #define I596_CONF11_MCALL_ 0x20 /* Multicast all */
292 #define I596_CONF13_RESERVED 0x3f /* Reserved: must be ones */
293 #define I596_CONF13_MULTIA 0x40 /* Enable multiple addr. reception */
294 #define I596_CONF13_DISBOF 0x80 /* Disable backoff algorithm */
296 * I596_CB_MCAST: Multicast-Setup Command (p. 4-54)
298 typedef volatile struct
300 ushort status;
301 ushort cmd;
302 union _I596_CB *next;
303 ushort count; /* Number of 6-byte addrs that follow */
304 uchar addr[6][1];
305 } I596_CB_MCAST;
308 * I596_CB_XMIT: Transmit Command (p. 4-56)
310 typedef I596_TFD I596_CB_XMIT;
312 #define I596_CB_XMIT_NOCRC 0x0010 /* cmd: No CRC insertion */
313 #define I596_CB_XMIT_FLEX 0x0008 /* cmd: Flexible memory mode */
315 #define I596_CB_XMIT_ERR_LATE 0x0800 /* status: error: late collision */
316 #define I596_CB_XMIT_ERR_NOCRS 0x0400 /* status: error: no carriers sense */
317 #define I596_CB_XMIT_ERR_NOCTS 0x0200 /* status: error: loss of CTS */
318 #define I596_CB_XMIT_ERR_UNDER 0x0100 /* status: error: DMA underrun */
319 #define I596_CB_XMIT_ERR_MAXCOL 0x0020 /* status: error: maximum collisions */
320 #define I596_CB_XMIT_COLLISIONS 0x000f /* status: number of collisions */
323 * I596_CB_TDR: Time Domain Reflectometry Command (p. 4-63)
325 typedef volatile struct
327 ushort status;
328 ushort cmd;
329 union _I596_CB *next;
330 ushort time;
331 } I596_CB_TDR;
334 * I596_CB_DUMP: Dump Command (p. 4-65)
336 typedef volatile struct
338 ushort status;
339 ushort cmd;
340 union _I596_CB *next;
341 uchar *buf;
342 } I596_CB_DUMP;
345 * I596_CB_DIAG: Diagnose Command (p. 4-77)
347 typedef volatile struct
349 ushort status;
350 ushort cmd;
351 union _I596_CB *next;
352 } I596_CB_DIAG;
355 * I596_CB: Command Block
357 typedef union _I596_CB
359 I596_CB_NOP nop;
360 I596_CB_IA ia;
361 I596_CB_CONF conf;
362 I596_CB_MCAST mcast;
363 I596_CB_XMIT xmit;
364 I596_CB_TDR tdr;
365 I596_CB_DUMP dump;
366 I596_CB_DIAG diag;
368 /* command and status in one ulong for speed... */
369 I596_CB_FAST fast;
370 } I596_CB;
372 /************************************************************************/
373 /* */
374 /* I596_SCB: System Configuration Block (p. 4-26) */
375 /* */
376 /************************************************************************/
377 typedef volatile struct
379 volatile ushort status; /* Status word */
380 volatile ushort cmd; /* Command word */
381 I596_CB *cbp;
382 I596_RFD *rfdp;
383 ulong crc_errs;
384 ulong align_errs;
385 ulong resource_errs;
386 ulong overrun_errs;
387 ulong rcvcdt_errs;
388 ulong short_errs;
389 ushort toff;
390 ushort ton;
391 } I596_SCB;
393 /* cmd halfword values */
394 #define I596_SCB_ACK 0xF000 /* ACKNOWLEDGMENTS */
395 #define I596_SCB_ACK_CX 0x8000 /* Ack command completion */
396 #define I596_SCB_ACK_FR 0x4000 /* Ack received frame */
397 #define I596_SCB_ACK_CNA 0x2000 /* Ack command unit not active */
398 #define I596_SCB_ACK_RNR 0x1000 /* Ack rcv unit not ready */
399 #define I596_SCB_ACK_ALL 0xF000 /* Ack everything */
401 #define I596_SCB_CUC 0x0700 /* COMMAND UNIT COMMANDS */
402 #define I596_SCB_CUC_NOP 0x0000 /* No operation */
403 #define I596_SCB_CUC_START 0x0100 /* Start execution of first CB */
404 #define I596_SCB_CUC_RESUME 0x0200 /* Resume execution */
405 #define I596_SCB_CUC_SUSPEND 0x0300 /* Suspend after current CB */
406 #define I596_SCB_CUC_ABORT 0x0400 /* Abort current CB immediately */
407 #define I596_SCB_CUC_LOAD 0x0500 /* Load Bus throttle timers */
408 #define I596_SCB_CUC_LOADIMM 0x0600 /* Load Bus throttle timers, now */
410 #define I596_SCB_RUC 0x0070 /* RECEIVE UNIT COMMANDS */
411 #define I596_SCB_RUC_NOP 0x0000 /* No operation */
412 #define I596_SCB_RUC_START 0x0010 /* Start reception */
413 #define I596_SCB_RUC_RESUME 0x0020 /* Resume reception */
414 #define I596_SCB_RUC_SUSPEND 0x0030 /* Suspend reception */
415 #define I596_SCB_RUC_ABORT 0x0040 /* Abort reception */
417 #define I596_SCB_RESET 0x0080 /* Hard reset chip */
419 /* status halfword values */
420 #define I596_SCB_STAT 0xF000 /* STATUS */
421 #define I596_SCB_CX 0x8000 /* command completion */
422 #define I596_SCB_FR 0x4000 /* received frame */
423 #define I596_SCB_CNA 0x2000 /* command unit not active */
424 #define I596_SCB_RNR 0x1000 /* rcv unit not ready */
426 #define I596_SCB_CUS 0x0700 /* COMMAND UNIT STATUS */
427 #define I596_SCB_CUS_IDLE 0x0000 /* Idle */
428 #define I596_SCB_CUS_SUSPENDED 0x0100 /* Suspended */
429 #define I596_SCB_CUS_ACTIVE 0x0200 /* Active */
431 #define I596_SCB_RUS 0x00F0 /* RECEIVE UNIT STATUS */
432 #define I596_SCB_RUS_IDLE 0x0000 /* Idle */
433 #define I596_SCB_RUS_SUSPENDED 0x0010 /* Suspended */
434 #define I596_SCB_RUS_NORES 0x0020 /* No Resources */
435 #define I596_SCB_RUS_READY 0x0040 /* Ready */
436 #define I596_SCB_RUS_NORBDS 0x0080 /* No more RBDs modifier */
438 #define I596_SCB_LOADED 0x0008 /* Bus timers loaded */
440 /************************************************************************/
441 /* */
442 /* I596_ISCP: Intermediate System Configuration Ptr (p 4-26) */
443 /* */
444 /************************************************************************/
445 typedef volatile struct
447 ulong busy; /* Set to 1; I596 clears it when scbp is read */
448 I596_SCB *scbp;
449 } I596_ISCP;
451 /************************************************************************/
452 /* */
453 /* I596_SCP: System Configuration Pointer (p. 4-23) */
454 /* */
455 /************************************************************************/
456 typedef volatile struct
458 ulong sysbus;
459 ulong dummy;
460 I596_ISCP *iscpp;
461 } I596_SCP;
463 /* .sysbus values */
464 #define I596_SCP_RESERVED 0x400000 /* Reserved bits must be set */
465 #define I596_SCP_INTLOW 0x200000 /* Intr. Polarity active low */
466 #define I596_SCP_INTHIGH 0 /* Intr. Polarity active high */
467 #define I596_SCP_LOCKDIS 0x100000 /* Lock Function disabled */
468 #define I596_SCP_LOCKEN 0 /* Lock Function enabled */
469 #define I596_SCP_ETHROTTLE 0x080000 /* External Bus Throttle */
470 #define I596_SCP_ITHROTTLE 0 /* Internal Bus Throttle */
471 #define I596_SCP_LINEAR 0x040000 /* Linear Mode */
472 #define I596_SCP_SEGMENTED 0x020000 /* Segmented Mode */
473 #define I596_SCP_82586 0x000000 /* 82586 Mode */