drivers/net/sfc/txc43128_phy.c

   1 /****************************************************************************
   2  * Driver for Solarflare Solarstorm network controllers and boards
   3  * Copyright 2006-2011 Solarflare Communications Inc.
   4  *
   5  * This program is free software; you can redistribute it and/or modify it
   6  * under the terms of the GNU General Public License version 2 as published
   7  * by the Free Software Foundation, incorporated herein by reference.
   8  */
   9
  10 /*
  11  * Driver for Transwitch/Mysticom CX4 retimer
  12  * see www.transwitch.com, part is TXC-43128
  13  */
  14
  15 #include <linux/delay.h>
  16 #include <linux/slab.h>
  17 #include "efx.h"
  18 #include "mdio_10g.h"
  19 #include "phy.h"
  20 #include "nic.h"
  21
  22 /* We expect these MMDs to be in the package */
  23 #define TXC_REQUIRED_DEVS (MDIO_DEVS_PCS |      \
  24                            MDIO_DEVS_PMAPMD |   \
  25                            MDIO_DEVS_PHYXS)
  26
  27 #define TXC_LOOPBACKS ((1 << LOOPBACK_PCS) |    \
  28                        (1 << LOOPBACK_PMAPMD) | \
  29                        (1 << LOOPBACK_PHYXS_WS))
  30
  31 /**************************************************************************
  32  *
  33  * Compile-time config
  34  *
  35  **************************************************************************
  36  */
  37 #define TXCNAME "TXC43128"
  38 /* Total length of time we'll wait for the PHY to come out of reset (ms) */
  39 #define TXC_MAX_RESET_TIME      500
  40 /* Interval between checks (ms) */
  41 #define TXC_RESET_WAIT          10
  42 /* How long to run BIST (us) */
  43 #define TXC_BIST_DURATION       50
  44
  45 /**************************************************************************
  46  *
  47  * Register definitions
  48  *
  49  **************************************************************************
  50  */
  51
  52 /* Command register */
  53 #define TXC_GLRGS_GLCMD         0xc004
  54 /* Useful bits in command register */
  55 /* Lane power-down */
  56 #define TXC_GLCMD_L01PD_LBN     5
  57 #define TXC_GLCMD_L23PD_LBN     6
  58 /* Limited SW reset: preserves configuration but
  59  * initiates a logic reset. Self-clearing */
  60 #define TXC_GLCMD_LMTSWRST_LBN  14
  61
  62 /* Signal Quality Control */
  63 #define TXC_GLRGS_GSGQLCTL      0xc01a
  64 /* Enable bit */
  65 #define TXC_GSGQLCT_SGQLEN_LBN  15
  66 /* Lane selection */
  67 #define TXC_GSGQLCT_LNSL_LBN    13
  68 #define TXC_GSGQLCT_LNSL_WIDTH  2
  69
  70 /* Analog TX control */
  71 #define TXC_ALRGS_ATXCTL        0xc040
  72 /* Lane power-down */
  73 #define TXC_ATXCTL_TXPD3_LBN    15
  74 #define TXC_ATXCTL_TXPD2_LBN    14
  75 #define TXC_ATXCTL_TXPD1_LBN    13
  76 #define TXC_ATXCTL_TXPD0_LBN    12
  77
  78 /* Amplitude on lanes 0, 1 */
  79 #define TXC_ALRGS_ATXAMP0       0xc041
  80 /* Amplitude on lanes 2, 3 */
  81 #define TXC_ALRGS_ATXAMP1       0xc042
  82 /* Bit position of value for lane 0 (or 2) */
  83 #define TXC_ATXAMP_LANE02_LBN   3
  84 /* Bit position of value for lane 1 (or 3) */
  85 #define TXC_ATXAMP_LANE13_LBN   11
  86
  87 #define TXC_ATXAMP_1280_mV      0
  88 #define TXC_ATXAMP_1200_mV      8
  89 #define TXC_ATXAMP_1120_mV      12
  90 #define TXC_ATXAMP_1060_mV      14
  91 #define TXC_ATXAMP_0820_mV      25
  92 #define TXC_ATXAMP_0720_mV      26
  93 #define TXC_ATXAMP_0580_mV      27
  94 #define TXC_ATXAMP_0440_mV      28
  95
  96 #define TXC_ATXAMP_0820_BOTH                                    \
  97         ((TXC_ATXAMP_0820_mV << TXC_ATXAMP_LANE02_LBN)          \
  98          | (TXC_ATXAMP_0820_mV << TXC_ATXAMP_LANE13_LBN))
  99
 100 #define TXC_ATXAMP_DEFAULT      0x6060 /* From databook */
 101
 102 /* Preemphasis on lanes 0, 1 */
 103 #define TXC_ALRGS_ATXPRE0       0xc043
 104 /* Preemphasis on lanes 2, 3 */
 105 #define TXC_ALRGS_ATXPRE1       0xc044
 106
 107 #define TXC_ATXPRE_NONE 0
 108 #define TXC_ATXPRE_DEFAULT      0x1010 /* From databook */
 109
 110 #define TXC_ALRGS_ARXCTL        0xc045
 111 /* Lane power-down */
 112 #define TXC_ARXCTL_RXPD3_LBN    15
 113 #define TXC_ARXCTL_RXPD2_LBN    14
 114 #define TXC_ARXCTL_RXPD1_LBN    13
 115 #define TXC_ARXCTL_RXPD0_LBN    12
 116
 117 /* Main control */
 118 #define TXC_MRGS_CTL            0xc340
 119 /* Bits in main control */
 120 #define TXC_MCTL_RESET_LBN      15      /* Self clear */
 121 #define TXC_MCTL_TXLED_LBN      14      /* 1 to show align status */
 122 #define TXC_MCTL_RXLED_LBN      13      /* 1 to show align status */
 123
 124 /* GPIO output */
 125 #define TXC_GPIO_OUTPUT         0xc346
 126 #define TXC_GPIO_DIR            0xc348
 127
 128 /* Vendor-specific BIST registers */
 129 #define TXC_BIST_CTL            0xc280
 130 #define TXC_BIST_TXFRMCNT       0xc281
 131 #define TXC_BIST_RX0FRMCNT      0xc282
 132 #define TXC_BIST_RX1FRMCNT      0xc283
 133 #define TXC_BIST_RX2FRMCNT      0xc284
 134 #define TXC_BIST_RX3FRMCNT      0xc285
 135 #define TXC_BIST_RX0ERRCNT      0xc286
 136 #define TXC_BIST_RX1ERRCNT      0xc287
 137 #define TXC_BIST_RX2ERRCNT      0xc288
 138 #define TXC_BIST_RX3ERRCNT      0xc289
 139
 140 /* BIST type (controls bit patter in test) */
 141 #define TXC_BIST_CTRL_TYPE_LBN  10
 142 #define TXC_BIST_CTRL_TYPE_TSD  0       /* TranSwitch Deterministic */
 143 #define TXC_BIST_CTRL_TYPE_CRP  1       /* CRPAT standard */
 144 #define TXC_BIST_CTRL_TYPE_CJP  2       /* CJPAT standard */
 145 #define TXC_BIST_CTRL_TYPE_TSR  3       /* TranSwitch pseudo-random */
 146 /* Set this to 1 for 10 bit and 0 for 8 bit */
 147 #define TXC_BIST_CTRL_B10EN_LBN 12
 148 /* Enable BIST (write 0 to disable) */
 149 #define TXC_BIST_CTRL_ENAB_LBN  13
 150 /* Stop BIST (self-clears when stop complete) */
 151 #define TXC_BIST_CTRL_STOP_LBN  14
 152 /* Start BIST (cleared by writing 1 to STOP) */
 153 #define TXC_BIST_CTRL_STRT_LBN  15
 154
 155 /* Mt. Diablo test configuration */
 156 #define TXC_MTDIABLO_CTRL       0xc34f
 157 #define TXC_MTDIABLO_CTRL_PMA_LOOP_LBN  10
 158
 159 struct txc43128_data {
 160         unsigned long bug10934_timer;
 161         enum efx_phy_mode phy_mode;
 162         enum efx_loopback_mode loopback_mode;
 163 };
 164
 165 /* The PHY sometimes needs a reset to bring the link back up.  So long as
 166  * it reports link down, we reset it every 5 seconds.
 167  */
 168 #define BUG10934_RESET_INTERVAL (5 * HZ)
 169
 170 /* Perform a reset that doesn't clear configuration changes */
 171 static void txc_reset_logic(struct efx_nic *efx);
 172
 173 /* Set the output value of a gpio */
 174 void falcon_txc_set_gpio_val(struct efx_nic *efx, int pin, int on)
 175 {
 176         efx_mdio_set_flag(efx, MDIO_MMD_PHYXS, TXC_GPIO_OUTPUT, 1 << pin, on);
 177 }
 178
 179 /* Set up the GPIO direction register */
 180 void falcon_txc_set_gpio_dir(struct efx_nic *efx, int pin, int dir)
 181 {
 182         efx_mdio_set_flag(efx, MDIO_MMD_PHYXS, TXC_GPIO_DIR, 1 << pin, dir);
 183 }
 184
 185 /* Reset the PMA/PMD MMD. The documentation is explicit that this does a
 186  * global reset (it's less clear what reset of other MMDs does).*/
 187 static int txc_reset_phy(struct efx_nic *efx)
 188 {
 189         int rc = efx_mdio_reset_mmd(efx, MDIO_MMD_PMAPMD,
 190                                     TXC_MAX_RESET_TIME / TXC_RESET_WAIT,
 191                                     TXC_RESET_WAIT);
 192         if (rc < 0)
 193                 goto fail;
 194
 195         /* Check that all the MMDs we expect are present and responding. */
 196         rc = efx_mdio_check_mmds(efx, TXC_REQUIRED_DEVS);
 197         if (rc < 0)
 198                 goto fail;
 199
 200         return 0;
 201
 202 fail:
 203         netif_err(efx, hw, efx->net_dev, TXCNAME ": reset timed out!\n");
 204         return rc;
 205 }
 206
 207 /* Run a single BIST on one MMD */
 208 static int txc_bist_one(struct efx_nic *efx, int mmd, int test)
 209 {
 210         int ctrl, bctl;
 211         int lane;
 212         int rc = 0;
 213
 214         /* Set PMA to test into loopback using Mt Diablo reg as per app note */
 215         ctrl = efx_mdio_read(efx, MDIO_MMD_PCS, TXC_MTDIABLO_CTRL);
 216         ctrl |= (1 << TXC_MTDIABLO_CTRL_PMA_LOOP_LBN);
 217         efx_mdio_write(efx, MDIO_MMD_PCS, TXC_MTDIABLO_CTRL, ctrl);
 218
 219         /* The BIST app. note lists these  as 3 distinct steps. */
 220         /* Set the BIST type */
 221         bctl = (test << TXC_BIST_CTRL_TYPE_LBN);
 222         efx_mdio_write(efx, mmd, TXC_BIST_CTL, bctl);
 223
 224         /* Set the BSTEN bit in the BIST Control register to enable */
 225         bctl |= (1 << TXC_BIST_CTRL_ENAB_LBN);
 226         efx_mdio_write(efx, mmd, TXC_BIST_CTL, bctl);
 227
 228         /* Set the BSTRT bit in the BIST Control register */
 229         efx_mdio_write(efx, mmd, TXC_BIST_CTL,
 230                        bctl | (1 << TXC_BIST_CTRL_STRT_LBN));
 231
 232         /* Wait. */
 233         udelay(TXC_BIST_DURATION);
 234
 235         /* Set the BSTOP bit in the BIST Control register */
 236         bctl |= (1 << TXC_BIST_CTRL_STOP_LBN);
 237         efx_mdio_write(efx, mmd, TXC_BIST_CTL, bctl);
 238
 239         /* The STOP bit should go off when things have stopped */
 240         while (bctl & (1 << TXC_BIST_CTRL_STOP_LBN))
 241                 bctl = efx_mdio_read(efx, mmd, TXC_BIST_CTL);
 242
 243         /* Check all the error counts are 0 and all the frame counts are
 244            non-zero */
 245         for (lane = 0; lane < 4; lane++) {
 246                 int count = efx_mdio_read(efx, mmd, TXC_BIST_RX0ERRCNT + lane);
 247                 if (count != 0) {
 248                         netif_err(efx, hw, efx->net_dev, TXCNAME": BIST error. "
 249                                   "Lane %d had %d errs\n", lane, count);
 250                         rc = -EIO;
 251                 }
 252                 count = efx_mdio_read(efx, mmd, TXC_BIST_RX0FRMCNT + lane);
 253                 if (count == 0) {
 254                         netif_err(efx, hw, efx->net_dev, TXCNAME": BIST error. "
 255                                   "Lane %d got 0 frames\n", lane);
 256                         rc = -EIO;
 257                 }
 258         }
 259
 260         if (rc == 0)
 261                 netif_info(efx, hw, efx->net_dev, TXCNAME": BIST pass\n");
 262
 263         /* Disable BIST */
 264         efx_mdio_write(efx, mmd, TXC_BIST_CTL, 0);
 265
 266         /* Turn off loopback */
 267         ctrl &= ~(1 << TXC_MTDIABLO_CTRL_PMA_LOOP_LBN);
 268         efx_mdio_write(efx, MDIO_MMD_PCS, TXC_MTDIABLO_CTRL, ctrl);
 269
 270         return rc;
 271 }
 272
 273 static int txc_bist(struct efx_nic *efx)
 274 {
 275         return txc_bist_one(efx, MDIO_MMD_PCS, TXC_BIST_CTRL_TYPE_TSD);
 276 }
 277
 278 /* Push the non-configurable defaults into the PHY. This must be
 279  * done after every full reset */
 280 static void txc_apply_defaults(struct efx_nic *efx)
 281 {
 282         int mctrl;
 283
 284         /* Turn amplitude down and preemphasis off on the host side
 285          * (PHY<->MAC) as this is believed less likely to upset Falcon
 286          * and no adverse effects have been noted. It probably also
 287          * saves a picowatt or two */
 288
 289         /* Turn off preemphasis */
 290         efx_mdio_write(efx, MDIO_MMD_PHYXS, TXC_ALRGS_ATXPRE0, TXC_ATXPRE_NONE);
 291         efx_mdio_write(efx, MDIO_MMD_PHYXS, TXC_ALRGS_ATXPRE1, TXC_ATXPRE_NONE);
 292
 293         /* Turn down the amplitude */
 294         efx_mdio_write(efx, MDIO_MMD_PHYXS,
 295                        TXC_ALRGS_ATXAMP0, TXC_ATXAMP_0820_BOTH);
 296         efx_mdio_write(efx, MDIO_MMD_PHYXS,
 297                        TXC_ALRGS_ATXAMP1, TXC_ATXAMP_0820_BOTH);
 298
 299         /* Set the line side amplitude and preemphasis to the databook
 300          * defaults as an erratum causes them to be 0 on at least some
 301          * PHY rev.s */
 302         efx_mdio_write(efx, MDIO_MMD_PMAPMD,
 303                        TXC_ALRGS_ATXPRE0, TXC_ATXPRE_DEFAULT);
 304         efx_mdio_write(efx, MDIO_MMD_PMAPMD,
 305                        TXC_ALRGS_ATXPRE1, TXC_ATXPRE_DEFAULT);
 306         efx_mdio_write(efx, MDIO_MMD_PMAPMD,
 307                        TXC_ALRGS_ATXAMP0, TXC_ATXAMP_DEFAULT);
 308         efx_mdio_write(efx, MDIO_MMD_PMAPMD,
 309                        TXC_ALRGS_ATXAMP1, TXC_ATXAMP_DEFAULT);
 310
 311         /* Set up the LEDs  */
 312         mctrl = efx_mdio_read(efx, MDIO_MMD_PHYXS, TXC_MRGS_CTL);
 313
 314         /* Set the Green and Red LEDs to their default modes */
 315         mctrl &= ~((1 << TXC_MCTL_TXLED_LBN) | (1 << TXC_MCTL_RXLED_LBN));
 316         efx_mdio_write(efx, MDIO_MMD_PHYXS, TXC_MRGS_CTL, mctrl);
 317
 318         /* Databook recommends doing this after configuration changes */
 319         txc_reset_logic(efx);
 320
 321         falcon_board(efx)->type->init_phy(efx);
 322 }
 323
 324 static int txc43128_phy_probe(struct efx_nic *efx)
 325 {
 326         struct txc43128_data *phy_data;
 327
 328         /* Allocate phy private storage */
 329         phy_data = kzalloc(sizeof(*phy_data), GFP_KERNEL);
 330         if (!phy_data)
 331                 return -ENOMEM;
 332         efx->phy_data = phy_data;
 333         phy_data->phy_mode = efx->phy_mode;
 334
 335         efx->mdio.mmds = TXC_REQUIRED_DEVS;
 336         efx->mdio.mode_support = MDIO_SUPPORTS_C45 | MDIO_EMULATE_C22;
 337
 338         efx->loopback_modes = TXC_LOOPBACKS | FALCON_XMAC_LOOPBACKS;
 339
 340         return 0;
 341 }
 342
 343 /* Initialisation entry point for this PHY driver */
 344 static int txc43128_phy_init(struct efx_nic *efx)
 345 {
 346         int rc;
 347
 348         rc = txc_reset_phy(efx);
 349         if (rc < 0)
 350                 return rc;
 351
 352         rc = txc_bist(efx);
 353         if (rc < 0)
 354                 return rc;
 355
 356         txc_apply_defaults(efx);
 357
 358         return 0;
 359 }
 360
 361 /* Set the lane power down state in the global registers */
 362 static void txc_glrgs_lane_power(struct efx_nic *efx, int mmd)
 363 {
 364         int pd = (1 << TXC_GLCMD_L01PD_LBN) | (1 << TXC_GLCMD_L23PD_LBN);
 365         int ctl = efx_mdio_read(efx, mmd, TXC_GLRGS_GLCMD);
 366
 367         if (!(efx->phy_mode & PHY_MODE_LOW_POWER))
 368                 ctl &= ~pd;
 369         else
 370                 ctl |= pd;
 371
 372         efx_mdio_write(efx, mmd, TXC_GLRGS_GLCMD, ctl);
 373 }
 374
 375 /* Set the lane power down state in the analog control registers */
 376 static void txc_analog_lane_power(struct efx_nic *efx, int mmd)
 377 {
 378         int txpd = (1 << TXC_ATXCTL_TXPD3_LBN) | (1 << TXC_ATXCTL_TXPD2_LBN)
 379                 | (1 << TXC_ATXCTL_TXPD1_LBN) | (1 << TXC_ATXCTL_TXPD0_LBN);
 380         int rxpd = (1 << TXC_ARXCTL_RXPD3_LBN) | (1 << TXC_ARXCTL_RXPD2_LBN)
 381                 | (1 << TXC_ARXCTL_RXPD1_LBN) | (1 << TXC_ARXCTL_RXPD0_LBN);
 382         int txctl = efx_mdio_read(efx, mmd, TXC_ALRGS_ATXCTL);
 383         int rxctl = efx_mdio_read(efx, mmd, TXC_ALRGS_ARXCTL);
 384
 385         if (!(efx->phy_mode & PHY_MODE_LOW_POWER)) {
 386                 txctl &= ~txpd;
 387                 rxctl &= ~rxpd;
 388         } else {
 389                 txctl |= txpd;
 390                 rxctl |= rxpd;
 391         }
 392
 393         efx_mdio_write(efx, mmd, TXC_ALRGS_ATXCTL, txctl);
 394         efx_mdio_write(efx, mmd, TXC_ALRGS_ARXCTL, rxctl);
 395 }
 396
 397 static void txc_set_power(struct efx_nic *efx)
 398 {
 399         /* According to the data book, all the MMDs can do low power */
 400         efx_mdio_set_mmds_lpower(efx,
 401                                  !!(efx->phy_mode & PHY_MODE_LOW_POWER),
 402                                  TXC_REQUIRED_DEVS);
 403
 404         /* Global register bank is in PCS, PHY XS. These control the host
 405          * side and line side settings respectively. */
 406         txc_glrgs_lane_power(efx, MDIO_MMD_PCS);
 407         txc_glrgs_lane_power(efx, MDIO_MMD_PHYXS);
 408
 409         /* Analog register bank in PMA/PMD, PHY XS */
 410         txc_analog_lane_power(efx, MDIO_MMD_PMAPMD);
 411         txc_analog_lane_power(efx, MDIO_MMD_PHYXS);
 412 }
 413
 414 static void txc_reset_logic_mmd(struct efx_nic *efx, int mmd)
 415 {
 416         int val = efx_mdio_read(efx, mmd, TXC_GLRGS_GLCMD);
 417         int tries = 50;
 418
 419         val |= (1 << TXC_GLCMD_LMTSWRST_LBN);
 420         efx_mdio_write(efx, mmd, TXC_GLRGS_GLCMD, val);
 421         while (tries--) {
 422                 val = efx_mdio_read(efx, mmd, TXC_GLRGS_GLCMD);
 423                 if (!(val & (1 << TXC_GLCMD_LMTSWRST_LBN)))
 424                         break;
 425                 udelay(1);
 426         }
 427         if (!tries)
 428                 netif_info(efx, hw, efx->net_dev,
 429                            TXCNAME " Logic reset timed out!\n");
 430 }
 431
 432 /* Perform a logic reset. This preserves the configuration registers
 433  * and is needed for some configuration changes to take effect */
 434 static void txc_reset_logic(struct efx_nic *efx)
 435 {
 436         /* The data sheet claims we can do the logic reset on either the
 437          * PCS or the PHYXS and the result is a reset of both host- and
 438          * line-side logic. */
 439         txc_reset_logic_mmd(efx, MDIO_MMD_PCS);
 440 }
 441
 442 static bool txc43128_phy_read_link(struct efx_nic *efx)
 443 {
 444         return efx_mdio_links_ok(efx, TXC_REQUIRED_DEVS);
 445 }
 446
 447 static int txc43128_phy_reconfigure(struct efx_nic *efx)
 448 {
 449         struct txc43128_data *phy_data = efx->phy_data;
 450         enum efx_phy_mode mode_change = efx->phy_mode ^ phy_data->phy_mode;
 451         bool loop_change = LOOPBACK_CHANGED(phy_data, efx, TXC_LOOPBACKS);
 452
 453         if (efx->phy_mode & mode_change & PHY_MODE_TX_DISABLED) {
 454                 txc_reset_phy(efx);
 455                 txc_apply_defaults(efx);
 456                 falcon_reset_xaui(efx);
 457                 mode_change &= ~PHY_MODE_TX_DISABLED;
 458         }
 459
 460         efx_mdio_transmit_disable(efx);
 461         efx_mdio_phy_reconfigure(efx);
 462         if (mode_change & PHY_MODE_LOW_POWER)
 463                 txc_set_power(efx);
 464
 465         /* The data sheet claims this is required after every reconfiguration
 466          * (note at end of 7.1), but we mustn't do it when nothing changes as
 467          * it glitches the link, and reconfigure gets called on link change,
 468          * so we get an IRQ storm on link up. */
 469         if (loop_change || mode_change)
 470                 txc_reset_logic(efx);
 471
 472         phy_data->phy_mode = efx->phy_mode;
 473         phy_data->loopback_mode = efx->loopback_mode;
 474
 475         return 0;
 476 }
 477
 478 static void txc43128_phy_fini(struct efx_nic *efx)
 479 {
 480         /* Disable link events */
 481         efx_mdio_write(efx, MDIO_MMD_PMAPMD, MDIO_PMA_LASI_CTRL, 0);
 482 }
 483
 484 static void txc43128_phy_remove(struct efx_nic *efx)
 485 {
 486         kfree(efx->phy_data);
 487         efx->phy_data = NULL;
 488 }
 489
 490 /* Periodic callback: this exists mainly to poll link status as we
 491  * don't use LASI interrupts */
 492 static bool txc43128_phy_poll(struct efx_nic *efx)
 493 {
 494         struct txc43128_data *data = efx->phy_data;
 495         bool was_up = efx->link_state.up;
 496
 497         efx->link_state.up = txc43128_phy_read_link(efx);
 498         efx->link_state.speed = 10000;
 499         efx->link_state.fd = true;
 500         efx->link_state.fc = efx->wanted_fc;
 501
 502         if (efx->link_state.up || (efx->loopback_mode != LOOPBACK_NONE)) {
 503                 data->bug10934_timer = jiffies;
 504         } else {
 505                 if (time_after_eq(jiffies, (data->bug10934_timer +
 506                                             BUG10934_RESET_INTERVAL))) {
 507                         data->bug10934_timer = jiffies;
 508                         txc_reset_logic(efx);
 509                 }
 510         }
 511
 512         return efx->link_state.up != was_up;
 513 }
 514
 515 static const char *txc43128_test_names[] = {
 516         "bist"
 517 };
 518
 519 static const char *txc43128_test_name(struct efx_nic *efx, unsigned int index)
 520 {
 521         if (index < ARRAY_SIZE(txc43128_test_names))
 522                 return txc43128_test_names[index];
 523         return NULL;
 524 }
 525
 526 static int txc43128_run_tests(struct efx_nic *efx, int *results, unsigned flags)
 527 {
 528         int rc;
 529
 530         if (!(flags & ETH_TEST_FL_OFFLINE))
 531                 return 0;
 532
 533         rc = txc_reset_phy(efx);
 534         if (rc < 0)
 535                 return rc;
 536
 537         rc = txc_bist(efx);
 538         txc_apply_defaults(efx);
 539         results[0] = rc ? -1 : 1;
 540         return rc;
 541 }
 542
 543 static void txc43128_get_settings(struct efx_nic *efx, struct ethtool_cmd *ecmd)
 544 {
 545         mdio45_ethtool_gset(&efx->mdio, ecmd);
 546 }
 547
 548 const struct efx_phy_operations falcon_txc_phy_ops = {
 549         .probe          = txc43128_phy_probe,
 550         .init           = txc43128_phy_init,
 551         .reconfigure    = txc43128_phy_reconfigure,
 552         .poll           = txc43128_phy_poll,
 553         .fini           = txc43128_phy_fini,
 554         .remove         = txc43128_phy_remove,
 555         .get_settings   = txc43128_get_settings,
 556         .set_settings   = efx_mdio_set_settings,
 557         .test_alive     = efx_mdio_test_alive,
 558         .run_tests      = txc43128_run_tests,
 559         .test_name      = txc43128_test_name,
 560 };