?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
clocksource: convert ARM 32-bit up counting clocksources
[linux-2.6/linux-acpi-2.6/ibm-acpi-2.6.git] / arch / arm / mach-lpc32xx / phy3250.c
blob7993b096778e1f49c9d44d3e2762dd58b4233678
1 /*
2 * arch/arm/mach-lpc32xx/phy3250.c
3 *
4 * Author: Kevin Wells <kevin.wells@nxp.com>
5 *
6 * Copyright (C) 2010 NXP Semiconductors
7 *
8 * This program is free software; you can redistribute it and/or modify
9 * it under the terms of the GNU General Public License as published by
10 * the Free Software Foundation; either version 2 of the License, or
11 * (at your option) any later version.
12 *
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
17 */
18
19 #include <linux/init.h>
20 #include <linux/platform_device.h>
21 #include <linux/sysdev.h>
22 #include <linux/interrupt.h>
23 #include <linux/irq.h>
24 #include <linux/dma-mapping.h>
25 #include <linux/device.h>
26 #include <linux/spi/spi.h>
27 #include <linux/spi/eeprom.h>
28 #include <linux/leds.h>
29 #include <linux/gpio.h>
30 #include <linux/amba/bus.h>
31 #include <linux/amba/clcd.h>
32 #include <linux/amba/pl022.h>
33
34 #include <asm/setup.h>
35 #include <asm/mach-types.h>
36 #include <asm/mach/arch.h>
37
38 #include <mach/hardware.h>
39 #include <mach/platform.h>
40 #include "common.h"
41
42 /*
43 * Mapped GPIOLIB GPIOs
44 */
45 #define SPI0_CS_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
46 #define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
47 #define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
48 #define LED_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 1)
49
50 /*
51 * AMBA LCD controller
52 */
53 static struct clcd_panel conn_lcd_panel = {
54 .mode = {
55 .name = "QVGA portrait",
56 .refresh = 60,
57 .xres = 240,
58 .yres = 320,
59 .pixclock = 191828,
60 .left_margin = 22,
61 .right_margin = 11,
62 .upper_margin = 2,
63 .lower_margin = 1,
64 .hsync_len = 5,
65 .vsync_len = 2,
66 .sync = 0,
67 .vmode = FB_VMODE_NONINTERLACED,
68 },
69 .width = -1,
70 .height = -1,
71 .tim2 = (TIM2_IVS | TIM2_IHS),
72 .cntl = (CNTL_BGR | CNTL_LCDTFT | CNTL_LCDVCOMP(1) |
73 CNTL_LCDBPP16_565),
74 .bpp = 16,
75 };
76 #define PANEL_SIZE (3 * SZ_64K)
77
78 static int lpc32xx_clcd_setup(struct clcd_fb *fb)
79 {
80 dma_addr_t dma;
81
82 fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev,
83 PANEL_SIZE, &dma, GFP_KERNEL);
84 if (!fb->fb.screen_base) {
85 printk(KERN_ERR "CLCD: unable to map framebuffer\n");
86 return -ENOMEM;
87 }
88
89 fb->fb.fix.smem_start = dma;
90 fb->fb.fix.smem_len = PANEL_SIZE;
91 fb->panel = &conn_lcd_panel;
92
93 if (gpio_request(LCD_POWER_GPIO, "LCD power"))
94 printk(KERN_ERR "Error requesting gpio %u",
95 LCD_POWER_GPIO);
96 else if (gpio_direction_output(LCD_POWER_GPIO, 1))
97 printk(KERN_ERR "Error setting gpio %u to output",
98 LCD_POWER_GPIO);
99
100 if (gpio_request(BKL_POWER_GPIO, "LCD backlight power"))
101 printk(KERN_ERR "Error requesting gpio %u",
102 BKL_POWER_GPIO);
103 else if (gpio_direction_output(BKL_POWER_GPIO, 1))
104 printk(KERN_ERR "Error setting gpio %u to output",
105 BKL_POWER_GPIO);
106
107 return 0;
108 }
109
110 static int lpc32xx_clcd_mmap(struct clcd_fb *fb, struct vm_area_struct *vma)
111 {
112 return dma_mmap_writecombine(&fb->dev->dev, vma,
113 fb->fb.screen_base, fb->fb.fix.smem_start,
114 fb->fb.fix.smem_len);
115 }
116
117 static void lpc32xx_clcd_remove(struct clcd_fb *fb)
118 {
119 dma_free_writecombine(&fb->dev->dev, fb->fb.fix.smem_len,
120 fb->fb.screen_base, fb->fb.fix.smem_start);
121 }
122
123 /*
124 * On some early LCD modules (1307.0), the backlight logic is inverted.
125 * For those board variants, swap the disable and enable states for
126 * BKL_POWER_GPIO.
127 */
128 static void clcd_disable(struct clcd_fb *fb)
129 {
130 gpio_set_value(BKL_POWER_GPIO, 0);
131 gpio_set_value(LCD_POWER_GPIO, 0);
132 }
133
134 static void clcd_enable(struct clcd_fb *fb)
135 {
136 gpio_set_value(BKL_POWER_GPIO, 1);
137 gpio_set_value(LCD_POWER_GPIO, 1);
138 }
139
140 static struct clcd_board lpc32xx_clcd_data = {
141 .name = "Phytec LCD",
142 .check = clcdfb_check,
143 .decode = clcdfb_decode,
144 .disable = clcd_disable,
145 .enable = clcd_enable,
146 .setup = lpc32xx_clcd_setup,
147 .mmap = lpc32xx_clcd_mmap,
148 .remove = lpc32xx_clcd_remove,
149 };
150
151 static struct amba_device lpc32xx_clcd_device = {
152 .dev = {
153 .coherent_dma_mask = ~0,
154 .init_name = "dev:clcd",
155 .platform_data = &lpc32xx_clcd_data,
156 },
157 .res = {
158 .start = LPC32XX_LCD_BASE,
159 .end = (LPC32XX_LCD_BASE + SZ_4K - 1),
160 .flags = IORESOURCE_MEM,
161 },
162 .dma_mask = ~0,
163 .irq = {IRQ_LPC32XX_LCD, NO_IRQ},
164 };
165
166 /*
167 * AMBA SSP (SPI)
168 */
169 static void phy3250_spi_cs_set(u32 control)
170 {
171 gpio_set_value(SPI0_CS_GPIO, (int) control);
172 }
173
174 static struct pl022_config_chip spi0_chip_info = {
175 .com_mode = INTERRUPT_TRANSFER,
176 .iface = SSP_INTERFACE_MOTOROLA_SPI,
177 .hierarchy = SSP_MASTER,
178 .slave_tx_disable = 0,
179 .rx_lev_trig = SSP_RX_4_OR_MORE_ELEM,
180 .tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC,
181 .ctrl_len = SSP_BITS_8,
182 .wait_state = SSP_MWIRE_WAIT_ZERO,
183 .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
184 .cs_control = phy3250_spi_cs_set,
185 };
186
187 static struct pl022_ssp_controller lpc32xx_ssp0_data = {
188 .bus_id = 0,
189 .num_chipselect = 1,
190 .enable_dma = 0,
191 };
192
193 static struct amba_device lpc32xx_ssp0_device = {
194 .dev = {
195 .coherent_dma_mask = ~0,
196 .init_name = "dev:ssp0",
197 .platform_data = &lpc32xx_ssp0_data,
198 },
199 .res = {
200 .start = LPC32XX_SSP0_BASE,
201 .end = (LPC32XX_SSP0_BASE + SZ_4K - 1),
202 .flags = IORESOURCE_MEM,
203 },
204 .dma_mask = ~0,
205 .irq = {IRQ_LPC32XX_SSP0, NO_IRQ},
206 };
207
208 /* AT25 driver registration */
209 static int __init phy3250_spi_board_register(void)
210 {
211 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
212 static struct spi_board_info info[] = {
213 {
214 .modalias = "spidev",
215 .max_speed_hz = 5000000,
216 .bus_num = 0,
217 .chip_select = 0,
218 .controller_data = &spi0_chip_info,
219 },
220 };
221
222 #else
223 static struct spi_eeprom eeprom = {
224 .name = "at25256a",
225 .byte_len = 0x8000,
226 .page_size = 64,
227 .flags = EE_ADDR2,
228 };
229
230 static struct spi_board_info info[] = {
231 {
232 .modalias = "at25",
233 .max_speed_hz = 5000000,
234 .bus_num = 0,
235 .chip_select = 0,
236 .mode = SPI_MODE_0,
237 .platform_data = &eeprom,
238 .controller_data = &spi0_chip_info,
239 },
240 };
241 #endif
242 return spi_register_board_info(info, ARRAY_SIZE(info));
243 }
244 arch_initcall(phy3250_spi_board_register);
245
246 static struct i2c_board_info __initdata phy3250_i2c_board_info[] = {
247 {
248 I2C_BOARD_INFO("pcf8563", 0x51),
249 },
250 };
251
252 static struct gpio_led phy_leds[] = {
253 {
254 .name = "led0",
255 .gpio = LED_GPIO,
256 .active_low = 1,
257 .default_trigger = "heartbeat",
258 },
259 };
260
261 static struct gpio_led_platform_data led_data = {
262 .leds = phy_leds,
263 .num_leds = ARRAY_SIZE(phy_leds),
264 };
265
266 static struct platform_device lpc32xx_gpio_led_device = {
267 .name = "leds-gpio",
268 .id = -1,
269 .dev.platform_data = &led_data,
270 };
271
272 static struct platform_device *phy3250_devs[] __initdata = {
273 &lpc32xx_i2c0_device,
274 &lpc32xx_i2c1_device,
275 &lpc32xx_i2c2_device,
276 &lpc32xx_watchdog_device,
277 &lpc32xx_gpio_led_device,
278 };
279
280 static struct amba_device *amba_devs[] __initdata = {
281 &lpc32xx_clcd_device,
282 &lpc32xx_ssp0_device,
283 };
284
285 /*
286 * Board specific functions
287 */
288 static void __init phy3250_board_init(void)
289 {
290 u32 tmp;
291 int i;
292
293 lpc32xx_gpio_init();
294
295 /* Register GPIOs used on this board */
296 if (gpio_request(SPI0_CS_GPIO, "spi0 cs"))
297 printk(KERN_ERR "Error requesting gpio %u",
298 SPI0_CS_GPIO);
299 else if (gpio_direction_output(SPI0_CS_GPIO, 1))
300 printk(KERN_ERR "Error setting gpio %u to output",
301 SPI0_CS_GPIO);
302
303 /* Setup network interface for RMII mode */
304 tmp = __raw_readl(LPC32XX_CLKPWR_MACCLK_CTRL);
305 tmp &= ~LPC32XX_CLKPWR_MACCTRL_PINS_MSK;
306 tmp |= LPC32XX_CLKPWR_MACCTRL_USE_RMII_PINS;
307 __raw_writel(tmp, LPC32XX_CLKPWR_MACCLK_CTRL);
308
309 /* Setup SLC NAND controller muxing */
310 __raw_writel(LPC32XX_CLKPWR_NANDCLK_SEL_SLC,
311 LPC32XX_CLKPWR_NAND_CLK_CTRL);
312
313 /* Setup LCD muxing to RGB565 */
314 tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL) &
315 ~(LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_MSK |
316 LPC32XX_CLKPWR_LCDCTRL_PSCALE_MSK);
317 tmp |= LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT16;
318 __raw_writel(tmp, LPC32XX_CLKPWR_LCDCLK_CTRL);
319
320 /* Set up I2C pull levels */
321 tmp = __raw_readl(LPC32XX_CLKPWR_I2C_CLK_CTRL);
322 tmp |= LPC32XX_CLKPWR_I2CCLK_USBI2CHI_DRIVE |
323 LPC32XX_CLKPWR_I2CCLK_I2C2HI_DRIVE;
324 __raw_writel(tmp, LPC32XX_CLKPWR_I2C_CLK_CTRL);
325
326 /* Disable IrDA pulsing support on UART6 */
327 tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
328 tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS;
329 __raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
330
331 /* Enable DMA for I2S1 channel */
332 tmp = __raw_readl(LPC32XX_CLKPWR_I2S_CLK_CTRL);
333 tmp = LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA;
334 __raw_writel(tmp, LPC32XX_CLKPWR_I2S_CLK_CTRL);
335
336 lpc32xx_serial_init();
337
338 /*
339 * AMBA peripheral clocks need to be enabled prior to AMBA device
340 * detection or a data fault will occur, so enable the clocks
341 * here. However, we don't want to enable them if the peripheral
342 * isn't included in the image
343 */
344 #ifdef CONFIG_FB_ARMCLCD
345 tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL);
346 __raw_writel((tmp | LPC32XX_CLKPWR_LCDCTRL_CLK_EN),
347 LPC32XX_CLKPWR_LCDCLK_CTRL);
348 #endif
349 #ifdef CONFIG_SPI_PL022
350 tmp = __raw_readl(LPC32XX_CLKPWR_SSP_CLK_CTRL);
351 __raw_writel((tmp | LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN),
352 LPC32XX_CLKPWR_SSP_CLK_CTRL);
353 #endif
354
355 platform_add_devices(phy3250_devs, ARRAY_SIZE(phy3250_devs));
356 for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
357 struct amba_device *d = amba_devs[i];
358 amba_device_register(d, &iomem_resource);
359 }
360
361 /* Test clock needed for UDA1380 initial init */
362 __raw_writel(LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC |
363 LPC32XX_CLKPWR_TESTCLK_TESTCLK2_EN,
364 LPC32XX_CLKPWR_TEST_CLK_SEL);
365
366 i2c_register_board_info(0, phy3250_i2c_board_info,
367 ARRAY_SIZE(phy3250_i2c_board_info));
368 }
369
370 static int __init lpc32xx_display_uid(void)
371 {
372 u32 uid[4];
373
374 lpc32xx_get_uid(uid);
375
376 printk(KERN_INFO "LPC32XX unique ID: %08x%08x%08x%08x\n",
377 uid[3], uid[2], uid[1], uid[0]);
378
379 return 1;
380 }
381 arch_initcall(lpc32xx_display_uid);
382
383 MACHINE_START(PHY3250, "Phytec 3250 board with the LPC3250 Microcontroller")
384 /* Maintainer: Kevin Wells, NXP Semiconductors */
385 .boot_params = 0x80000100,
386 .map_io = lpc32xx_map_io,
387 .init_irq = lpc32xx_init_irq,
388 .timer = &lpc32xx_timer,
389 .init_machine = phy3250_board_init,
390 MACHINE_END
Linux 2.6 ibm-acpi/thinkpad-acpi driver git tree