?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
drm/i915: Remove a bad BUG_ON in the fence management code.
[linux-2.6/linux-acpi-2.6/ibm-acpi-2.6.git] / drivers / serial / bfin_5xx.c
blobd86123e03391e97623103682271da36f51350ab2
1 /*
2 * Blackfin On-Chip Serial Driver
3 *
4 * Copyright 2006-2008 Analog Devices Inc.
5 *
6 * Enter bugs at http://blackfin.uclinux.org/
7 *
8 * Licensed under the GPL-2 or later.
9 */
10
11 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
12 #define SUPPORT_SYSRQ
13 #endif
14
15 #include <linux/module.h>
16 #include <linux/ioport.h>
17 #include <linux/init.h>
18 #include <linux/console.h>
19 #include <linux/sysrq.h>
20 #include <linux/platform_device.h>
21 #include <linux/tty.h>
22 #include <linux/tty_flip.h>
23 #include <linux/serial_core.h>
24
25 #if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
26 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
27 #include <linux/kgdb.h>
28 #include <asm/irq_regs.h>
29 #endif
30
31 #include <asm/gpio.h>
32 #include <mach/bfin_serial_5xx.h>
33
34 #ifdef CONFIG_SERIAL_BFIN_DMA
35 #include <linux/dma-mapping.h>
36 #include <asm/io.h>
37 #include <asm/irq.h>
38 #include <asm/cacheflush.h>
39 #endif
40
41 /* UART name and device definitions */
42 #define BFIN_SERIAL_NAME "ttyBF"
43 #define BFIN_SERIAL_MAJOR 204
44 #define BFIN_SERIAL_MINOR 64
45
46 static struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
47 static int nr_active_ports = ARRAY_SIZE(bfin_serial_resource);
48
49 #if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
50 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
51
52 # ifndef CONFIG_SERIAL_BFIN_PIO
53 # error KGDB only support UART in PIO mode.
54 # endif
55
56 static int kgdboc_port_line;
57 static int kgdboc_break_enabled;
58 #endif
59 /*
60 * Setup for console. Argument comes from the menuconfig
61 */
62 #define DMA_RX_XCOUNT 512
63 #define DMA_RX_YCOUNT (PAGE_SIZE / DMA_RX_XCOUNT)
64
65 #define DMA_RX_FLUSH_JIFFIES (HZ / 50)
66
67 #ifdef CONFIG_SERIAL_BFIN_DMA
68 static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
69 #else
70 static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
71 #endif
72
73 static void bfin_serial_reset_irda(struct uart_port *port);
74
75 #if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
76 defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
77 static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
78 {
79 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
80 if (uart->cts_pin < 0)
81 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
82
83 /* CTS PIN is negative assertive. */
84 if (UART_GET_CTS(uart))
85 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
86 else
87 return TIOCM_DSR | TIOCM_CAR;
88 }
89
90 static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
91 {
92 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
93 if (uart->rts_pin < 0)
94 return;
95
96 /* RTS PIN is negative assertive. */
97 if (mctrl & TIOCM_RTS)
98 UART_ENABLE_RTS(uart);
99 else
100 UART_DISABLE_RTS(uart);
101 }
102
103 /*
104 * Handle any change of modem status signal.
105 */
106 static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id)
107 {
108 struct bfin_serial_port *uart = dev_id;
109 unsigned int status;
110
111 status = bfin_serial_get_mctrl(&uart->port);
112 uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
113 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
114 uart->scts = 1;
115 UART_CLEAR_SCTS(uart);
116 UART_CLEAR_IER(uart, EDSSI);
117 #endif
118
119 return IRQ_HANDLED;
120 }
121 #else
122 static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
123 {
124 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
125 }
126
127 static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
128 {
129 }
130 #endif
131
132 /*
133 * interrupts are disabled on entry
134 */
135 static void bfin_serial_stop_tx(struct uart_port *port)
136 {
137 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
138 #ifdef CONFIG_SERIAL_BFIN_DMA
139 struct circ_buf *xmit = &uart->port.info->xmit;
140 #endif
141
142 while (!(UART_GET_LSR(uart) & TEMT))
143 cpu_relax();
144
145 #ifdef CONFIG_SERIAL_BFIN_DMA
146 disable_dma(uart->tx_dma_channel);
147 xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
148 uart->port.icount.tx += uart->tx_count;
149 uart->tx_count = 0;
150 uart->tx_done = 1;
151 #else
152 #ifdef CONFIG_BF54x
153 /* Clear TFI bit */
154 UART_PUT_LSR(uart, TFI);
155 #endif
156 UART_CLEAR_IER(uart, ETBEI);
157 #endif
158 }
159
160 /*
161 * port is locked and interrupts are disabled
162 */
163 static void bfin_serial_start_tx(struct uart_port *port)
164 {
165 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
166 struct tty_struct *tty = uart->port.info->port.tty;
167
168 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
169 if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) {
170 uart->scts = 0;
171 uart_handle_cts_change(&uart->port, uart->scts);
172 }
173 #endif
174
175 /*
176 * To avoid losting RX interrupt, we reset IR function
177 * before sending data.
178 */
179 if (tty->termios->c_line == N_IRDA)
180 bfin_serial_reset_irda(port);
181
182 #ifdef CONFIG_SERIAL_BFIN_DMA
183 if (uart->tx_done)
184 bfin_serial_dma_tx_chars(uart);
185 #else
186 UART_SET_IER(uart, ETBEI);
187 bfin_serial_tx_chars(uart);
188 #endif
189 }
190
191 /*
192 * Interrupts are enabled
193 */
194 static void bfin_serial_stop_rx(struct uart_port *port)
195 {
196 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
197
198 UART_CLEAR_IER(uart, ERBFI);
199 }
200
201 /*
202 * Set the modem control timer to fire immediately.
203 */
204 static void bfin_serial_enable_ms(struct uart_port *port)
205 {
206 }
207
208
209 #if ANOMALY_05000363 && defined(CONFIG_SERIAL_BFIN_PIO)
210 # define UART_GET_ANOMALY_THRESHOLD(uart) ((uart)->anomaly_threshold)
211 # define UART_SET_ANOMALY_THRESHOLD(uart, v) ((uart)->anomaly_threshold = (v))
212 #else
213 # define UART_GET_ANOMALY_THRESHOLD(uart) 0
214 # define UART_SET_ANOMALY_THRESHOLD(uart, v)
215 #endif
216
217 #ifdef CONFIG_SERIAL_BFIN_PIO
218 static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
219 {
220 struct tty_struct *tty = NULL;
221 unsigned int status, ch, flg;
222 static struct timeval anomaly_start = { .tv_sec = 0 };
223
224 status = UART_GET_LSR(uart);
225 UART_CLEAR_LSR(uart);
226
227 ch = UART_GET_CHAR(uart);
228 uart->port.icount.rx++;
229
230 #if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
231 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
232 if (kgdb_connected && kgdboc_port_line == uart->port.line)
233 if (ch == 0x3) {/* Ctrl + C */
234 kgdb_breakpoint();
235 return;
236 }
237
238 if (!uart->port.info || !uart->port.info->port.tty)
239 return;
240 #endif
241 tty = uart->port.info->port.tty;
242
243 if (ANOMALY_05000363) {
244 /* The BF533 (and BF561) family of processors have a nice anomaly
245 * where they continuously generate characters for a "single" break.
246 * We have to basically ignore this flood until the "next" valid
247 * character comes across. Due to the nature of the flood, it is
248 * not possible to reliably catch bytes that are sent too quickly
249 * after this break. So application code talking to the Blackfin
250 * which sends a break signal must allow at least 1.5 character
251 * times after the end of the break for things to stabilize. This
252 * timeout was picked as it must absolutely be larger than 1
253 * character time +/- some percent. So 1.5 sounds good. All other
254 * Blackfin families operate properly. Woo.
255 */
256 if (anomaly_start.tv_sec) {
257 struct timeval curr;
258 suseconds_t usecs;
259
260 if ((~ch & (~ch + 1)) & 0xff)
261 goto known_good_char;
262
263 do_gettimeofday(&curr);
264 if (curr.tv_sec - anomaly_start.tv_sec > 1)
265 goto known_good_char;
266
267 usecs = 0;
268 if (curr.tv_sec != anomaly_start.tv_sec)
269 usecs += USEC_PER_SEC;
270 usecs += curr.tv_usec - anomaly_start.tv_usec;
271
272 if (usecs > UART_GET_ANOMALY_THRESHOLD(uart))
273 goto known_good_char;
274
275 if (ch)
276 anomaly_start.tv_sec = 0;
277 else
278 anomaly_start = curr;
279
280 return;
281
282 known_good_char:
283 status &= ~BI;
284 anomaly_start.tv_sec = 0;
285 }
286 }
287
288 if (status & BI) {
289 if (ANOMALY_05000363)
290 if (bfin_revid() < 5)
291 do_gettimeofday(&anomaly_start);
292 uart->port.icount.brk++;
293 if (uart_handle_break(&uart->port))
294 goto ignore_char;
295 status &= ~(PE | FE);
296 }
297 if (status & PE)
298 uart->port.icount.parity++;
299 if (status & OE)
300 uart->port.icount.overrun++;
301 if (status & FE)
302 uart->port.icount.frame++;
303
304 status &= uart->port.read_status_mask;
305
306 if (status & BI)
307 flg = TTY_BREAK;
308 else if (status & PE)
309 flg = TTY_PARITY;
310 else if (status & FE)
311 flg = TTY_FRAME;
312 else
313 flg = TTY_NORMAL;
314
315 if (uart_handle_sysrq_char(&uart->port, ch))
316 goto ignore_char;
317
318 uart_insert_char(&uart->port, status, OE, ch, flg);
319
320 ignore_char:
321 tty_flip_buffer_push(tty);
322 }
323
324 static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
325 {
326 struct circ_buf *xmit = &uart->port.info->xmit;
327
328 if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
329 #ifdef CONFIG_BF54x
330 /* Clear TFI bit */
331 UART_PUT_LSR(uart, TFI);
332 #endif
333 UART_CLEAR_IER(uart, ETBEI);
334 return;
335 }
336
337 if (uart->port.x_char) {
338 UART_PUT_CHAR(uart, uart->port.x_char);
339 uart->port.icount.tx++;
340 uart->port.x_char = 0;
341 }
342
343 while ((UART_GET_LSR(uart) & THRE) && xmit->tail != xmit->head) {
344 UART_PUT_CHAR(uart, xmit->buf[xmit->tail]);
345 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
346 uart->port.icount.tx++;
347 SSYNC();
348 }
349
350 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
351 uart_write_wakeup(&uart->port);
352 }
353
354 static irqreturn_t bfin_serial_rx_int(int irq, void *dev_id)
355 {
356 struct bfin_serial_port *uart = dev_id;
357
358 spin_lock(&uart->port.lock);
359 while (UART_GET_LSR(uart) & DR)
360 bfin_serial_rx_chars(uart);
361 spin_unlock(&uart->port.lock);
362
363 return IRQ_HANDLED;
364 }
365
366 static irqreturn_t bfin_serial_tx_int(int irq, void *dev_id)
367 {
368 struct bfin_serial_port *uart = dev_id;
369
370 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
371 if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) {
372 uart->scts = 0;
373 uart_handle_cts_change(&uart->port, uart->scts);
374 }
375 #endif
376 spin_lock(&uart->port.lock);
377 if (UART_GET_LSR(uart) & THRE)
378 bfin_serial_tx_chars(uart);
379 spin_unlock(&uart->port.lock);
380
381 return IRQ_HANDLED;
382 }
383 #endif
384
385 #ifdef CONFIG_SERIAL_BFIN_DMA
386 static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
387 {
388 struct circ_buf *xmit = &uart->port.info->xmit;
389
390 uart->tx_done = 0;
391
392 if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
393 uart->tx_count = 0;
394 uart->tx_done = 1;
395 return;
396 }
397
398 if (uart->port.x_char) {
399 UART_PUT_CHAR(uart, uart->port.x_char);
400 uart->port.icount.tx++;
401 uart->port.x_char = 0;
402 }
403
404 uart->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE);
405 if (uart->tx_count > (UART_XMIT_SIZE - xmit->tail))
406 uart->tx_count = UART_XMIT_SIZE - xmit->tail;
407 blackfin_dcache_flush_range((unsigned long)(xmit->buf+xmit->tail),
408 (unsigned long)(xmit->buf+xmit->tail+uart->tx_count));
409 set_dma_config(uart->tx_dma_channel,
410 set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP,
411 INTR_ON_BUF,
412 DIMENSION_LINEAR,
413 DATA_SIZE_8,
414 DMA_SYNC_RESTART));
415 set_dma_start_addr(uart->tx_dma_channel, (unsigned long)(xmit->buf+xmit->tail));
416 set_dma_x_count(uart->tx_dma_channel, uart->tx_count);
417 set_dma_x_modify(uart->tx_dma_channel, 1);
418 enable_dma(uart->tx_dma_channel);
419
420 UART_SET_IER(uart, ETBEI);
421 }
422
423 static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
424 {
425 struct tty_struct *tty = uart->port.info->port.tty;
426 int i, flg, status;
427
428 status = UART_GET_LSR(uart);
429 UART_CLEAR_LSR(uart);
430
431 uart->port.icount.rx +=
432 CIRC_CNT(uart->rx_dma_buf.head, uart->rx_dma_buf.tail,
433 UART_XMIT_SIZE);
434
435 if (status & BI) {
436 uart->port.icount.brk++;
437 if (uart_handle_break(&uart->port))
438 goto dma_ignore_char;
439 status &= ~(PE | FE);
440 }
441 if (status & PE)
442 uart->port.icount.parity++;
443 if (status & OE)
444 uart->port.icount.overrun++;
445 if (status & FE)
446 uart->port.icount.frame++;
447
448 status &= uart->port.read_status_mask;
449
450 if (status & BI)
451 flg = TTY_BREAK;
452 else if (status & PE)
453 flg = TTY_PARITY;
454 else if (status & FE)
455 flg = TTY_FRAME;
456 else
457 flg = TTY_NORMAL;
458
459 for (i = uart->rx_dma_buf.tail; ; i++) {
460 if (i >= UART_XMIT_SIZE)
461 i = 0;
462 if (i == uart->rx_dma_buf.head)
463 break;
464 if (!uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
465 uart_insert_char(&uart->port, status, OE,
466 uart->rx_dma_buf.buf[i], flg);
467 }
468
469 dma_ignore_char:
470 tty_flip_buffer_push(tty);
471 }
472
473 void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
474 {
475 int x_pos, pos;
476 unsigned long flags;
477
478 spin_lock_irqsave(&uart->port.lock, flags);
479
480 uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
481 x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
482 uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
483 if (uart->rx_dma_nrows == DMA_RX_YCOUNT)
484 uart->rx_dma_nrows = 0;
485 x_pos = DMA_RX_XCOUNT - x_pos;
486 if (x_pos == DMA_RX_XCOUNT)
487 x_pos = 0;
488
489 pos = uart->rx_dma_nrows * DMA_RX_XCOUNT + x_pos;
490 if (pos != uart->rx_dma_buf.tail) {
491 uart->rx_dma_buf.head = pos;
492 bfin_serial_dma_rx_chars(uart);
493 uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
494 }
495
496 spin_unlock_irqrestore(&uart->port.lock, flags);
497
498 mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES);
499 }
500
501 static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
502 {
503 struct bfin_serial_port *uart = dev_id;
504 struct circ_buf *xmit = &uart->port.info->xmit;
505
506 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
507 if (uart->scts && !(bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
508 uart->scts = 0;
509 uart_handle_cts_change(&uart->port, uart->scts);
510 }
511 #endif
512
513 spin_lock(&uart->port.lock);
514 if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
515 disable_dma(uart->tx_dma_channel);
516 clear_dma_irqstat(uart->tx_dma_channel);
517 UART_CLEAR_IER(uart, ETBEI);
518 xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
519 uart->port.icount.tx += uart->tx_count;
520
521 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
522 uart_write_wakeup(&uart->port);
523
524 bfin_serial_dma_tx_chars(uart);
525 }
526
527 spin_unlock(&uart->port.lock);
528 return IRQ_HANDLED;
529 }
530
531 static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id)
532 {
533 struct bfin_serial_port *uart = dev_id;
534 unsigned short irqstat;
535
536 spin_lock(&uart->port.lock);
537 irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
538 clear_dma_irqstat(uart->rx_dma_channel);
539 bfin_serial_dma_rx_chars(uart);
540 spin_unlock(&uart->port.lock);
541
542 return IRQ_HANDLED;
543 }
544 #endif
545
546 /*
547 * Return TIOCSER_TEMT when transmitter is not busy.
548 */
549 static unsigned int bfin_serial_tx_empty(struct uart_port *port)
550 {
551 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
552 unsigned short lsr;
553
554 lsr = UART_GET_LSR(uart);
555 if (lsr & TEMT)
556 return TIOCSER_TEMT;
557 else
558 return 0;
559 }
560
561 static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
562 {
563 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
564 u16 lcr = UART_GET_LCR(uart);
565 if (break_state)
566 lcr |= SB;
567 else
568 lcr &= ~SB;
569 UART_PUT_LCR(uart, lcr);
570 SSYNC();
571 }
572
573 static int bfin_serial_startup(struct uart_port *port)
574 {
575 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
576
577 #ifdef CONFIG_SERIAL_BFIN_DMA
578 dma_addr_t dma_handle;
579
580 if (request_dma(uart->rx_dma_channel, "BFIN_UART_RX") < 0) {
581 printk(KERN_NOTICE "Unable to attach Blackfin UART RX DMA channel\n");
582 return -EBUSY;
583 }
584
585 if (request_dma(uart->tx_dma_channel, "BFIN_UART_TX") < 0) {
586 printk(KERN_NOTICE "Unable to attach Blackfin UART TX DMA channel\n");
587 free_dma(uart->rx_dma_channel);
588 return -EBUSY;
589 }
590
591 set_dma_callback(uart->rx_dma_channel, bfin_serial_dma_rx_int, uart);
592 set_dma_callback(uart->tx_dma_channel, bfin_serial_dma_tx_int, uart);
593
594 uart->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL, PAGE_SIZE, &dma_handle, GFP_DMA);
595 uart->rx_dma_buf.head = 0;
596 uart->rx_dma_buf.tail = 0;
597 uart->rx_dma_nrows = 0;
598
599 set_dma_config(uart->rx_dma_channel,
600 set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO,
601 INTR_ON_ROW, DIMENSION_2D,
602 DATA_SIZE_8,
603 DMA_SYNC_RESTART));
604 set_dma_x_count(uart->rx_dma_channel, DMA_RX_XCOUNT);
605 set_dma_x_modify(uart->rx_dma_channel, 1);
606 set_dma_y_count(uart->rx_dma_channel, DMA_RX_YCOUNT);
607 set_dma_y_modify(uart->rx_dma_channel, 1);
608 set_dma_start_addr(uart->rx_dma_channel, (unsigned long)uart->rx_dma_buf.buf);
609 enable_dma(uart->rx_dma_channel);
610
611 uart->rx_dma_timer.data = (unsigned long)(uart);
612 uart->rx_dma_timer.function = (void *)bfin_serial_rx_dma_timeout;
613 uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
614 add_timer(&(uart->rx_dma_timer));
615 #else
616 # if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
617 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
618 if (kgdboc_port_line == uart->port.line && kgdboc_break_enabled)
619 kgdboc_break_enabled = 0;
620 else {
621 # endif
622 if (request_irq(uart->port.irq, bfin_serial_rx_int, IRQF_DISABLED,
623 "BFIN_UART_RX", uart)) {
624 printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
625 return -EBUSY;
626 }
627
628 if (request_irq
629 (uart->port.irq+1, bfin_serial_tx_int, IRQF_DISABLED,
630 "BFIN_UART_TX", uart)) {
631 printk(KERN_NOTICE "Unable to attach BlackFin UART TX interrupt\n");
632 free_irq(uart->port.irq, uart);
633 return -EBUSY;
634 }
635
636 # ifdef CONFIG_BF54x
637 {
638 unsigned uart_dma_ch_rx, uart_dma_ch_tx;
639
640 switch (uart->port.irq) {
641 case IRQ_UART3_RX:
642 uart_dma_ch_rx = CH_UART3_RX;
643 uart_dma_ch_tx = CH_UART3_TX;
644 break;
645 case IRQ_UART2_RX:
646 uart_dma_ch_rx = CH_UART2_RX;
647 uart_dma_ch_tx = CH_UART2_TX;
648 break;
649 default:
650 uart_dma_ch_rx = uart_dma_ch_tx = 0;
651 break;
652 };
653
654 if (uart_dma_ch_rx &&
655 request_dma(uart_dma_ch_rx, "BFIN_UART_RX") < 0) {
656 printk(KERN_NOTICE"Fail to attach UART interrupt\n");
657 free_irq(uart->port.irq, uart);
658 free_irq(uart->port.irq + 1, uart);
659 return -EBUSY;
660 }
661 if (uart_dma_ch_tx &&
662 request_dma(uart_dma_ch_tx, "BFIN_UART_TX") < 0) {
663 printk(KERN_NOTICE "Fail to attach UART interrupt\n");
664 free_dma(uart_dma_ch_rx);
665 free_irq(uart->port.irq, uart);
666 free_irq(uart->port.irq + 1, uart);
667 return -EBUSY;
668 }
669 }
670 # endif
671 # if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
672 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
673 }
674 # endif
675 #endif
676
677 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
678 if (uart->cts_pin >= 0) {
679 if (request_irq(gpio_to_irq(uart->cts_pin),
680 bfin_serial_mctrl_cts_int,
681 IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
682 IRQF_DISABLED, "BFIN_UART_CTS", uart)) {
683 uart->cts_pin = -1;
684 pr_info("Unable to attach BlackFin UART CTS interrupt.\
685 So, disable it.\n");
686 }
687 }
688 if (uart->rts_pin >= 0) {
689 gpio_request(uart->rts_pin, DRIVER_NAME);
690 gpio_direction_output(uart->rts_pin, 0);
691 }
692 #endif
693 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
694 if (request_irq(uart->status_irq,
695 bfin_serial_mctrl_cts_int,
696 IRQF_DISABLED, "BFIN_UART_MODEM_STATUS", uart)) {
697 pr_info("Unable to attach BlackFin UART Modem \
698 Status interrupt.\n");
699 }
700
701 if (uart->cts_pin >= 0) {
702 gpio_request(uart->cts_pin, DRIVER_NAME);
703 gpio_direction_output(uart->cts_pin, 1);
704 }
705 if (uart->rts_pin >= 0) {
706 gpio_request(uart->rts_pin, DRIVER_NAME);
707 gpio_direction_output(uart->rts_pin, 0);
708 }
709
710 /* CTS RTS PINs are negative assertive. */
711 UART_PUT_MCR(uart, ACTS);
712 UART_SET_IER(uart, EDSSI);
713 #endif
714
715 UART_SET_IER(uart, ERBFI);
716 return 0;
717 }
718
719 static void bfin_serial_shutdown(struct uart_port *port)
720 {
721 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
722
723 #ifdef CONFIG_SERIAL_BFIN_DMA
724 disable_dma(uart->tx_dma_channel);
725 free_dma(uart->tx_dma_channel);
726 disable_dma(uart->rx_dma_channel);
727 free_dma(uart->rx_dma_channel);
728 del_timer(&(uart->rx_dma_timer));
729 dma_free_coherent(NULL, PAGE_SIZE, uart->rx_dma_buf.buf, 0);
730 #else
731 #ifdef CONFIG_BF54x
732 switch (uart->port.irq) {
733 case IRQ_UART3_RX:
734 free_dma(CH_UART3_RX);
735 free_dma(CH_UART3_TX);
736 break;
737 case IRQ_UART2_RX:
738 free_dma(CH_UART2_RX);
739 free_dma(CH_UART2_TX);
740 break;
741 default:
742 break;
743 };
744 #endif
745 free_irq(uart->port.irq, uart);
746 free_irq(uart->port.irq+1, uart);
747 #endif
748
749 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
750 if (uart->cts_pin >= 0)
751 free_irq(gpio_to_irq(uart->cts_pin), uart);
752 if (uart->rts_pin >= 0)
753 gpio_free(uart->rts_pin);
754 #endif
755 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
756 if (uart->cts_pin >= 0)
757 gpio_free(uart->cts_pin);
758 if (uart->rts_pin >= 0)
759 gpio_free(uart->rts_pin);
760 if (UART_GET_IER(uart) && EDSSI)
761 free_irq(uart->status_irq, uart);
762 #endif
763 }
764
765 static void
766 bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
767 struct ktermios *old)
768 {
769 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
770 unsigned long flags;
771 unsigned int baud, quot;
772 unsigned short val, ier, lcr = 0;
773
774 switch (termios->c_cflag & CSIZE) {
775 case CS8:
776 lcr = WLS(8);
777 break;
778 case CS7:
779 lcr = WLS(7);
780 break;
781 case CS6:
782 lcr = WLS(6);
783 break;
784 case CS5:
785 lcr = WLS(5);
786 break;
787 default:
788 printk(KERN_ERR "%s: word lengh not supported\n",
789 __func__);
790 }
791
792 if (termios->c_cflag & CSTOPB)
793 lcr |= STB;
794 if (termios->c_cflag & PARENB)
795 lcr |= PEN;
796 if (!(termios->c_cflag & PARODD))
797 lcr |= EPS;
798 if (termios->c_cflag & CMSPAR)
799 lcr |= STP;
800
801 port->read_status_mask = OE;
802 if (termios->c_iflag & INPCK)
803 port->read_status_mask |= (FE | PE);
804 if (termios->c_iflag & (BRKINT | PARMRK))
805 port->read_status_mask |= BI;
806
807 /*
808 * Characters to ignore
809 */
810 port->ignore_status_mask = 0;
811 if (termios->c_iflag & IGNPAR)
812 port->ignore_status_mask |= FE | PE;
813 if (termios->c_iflag & IGNBRK) {
814 port->ignore_status_mask |= BI;
815 /*
816 * If we're ignoring parity and break indicators,
817 * ignore overruns too (for real raw support).
818 */
819 if (termios->c_iflag & IGNPAR)
820 port->ignore_status_mask |= OE;
821 }
822
823 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
824 quot = uart_get_divisor(port, baud) - ANOMALY_05000230;
825 spin_lock_irqsave(&uart->port.lock, flags);
826
827 UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15);
828
829 /* Disable UART */
830 ier = UART_GET_IER(uart);
831 UART_DISABLE_INTS(uart);
832
833 /* Set DLAB in LCR to Access DLL and DLH */
834 UART_SET_DLAB(uart);
835
836 UART_PUT_DLL(uart, quot & 0xFF);
837 UART_PUT_DLH(uart, (quot >> 8) & 0xFF);
838 SSYNC();
839
840 /* Clear DLAB in LCR to Access THR RBR IER */
841 UART_CLEAR_DLAB(uart);
842
843 UART_PUT_LCR(uart, lcr);
844
845 /* Enable UART */
846 UART_ENABLE_INTS(uart, ier);
847
848 val = UART_GET_GCTL(uart);
849 val |= UCEN;
850 UART_PUT_GCTL(uart, val);
851
852 /* Port speed changed, update the per-port timeout. */
853 uart_update_timeout(port, termios->c_cflag, baud);
854
855 spin_unlock_irqrestore(&uart->port.lock, flags);
856 }
857
858 static const char *bfin_serial_type(struct uart_port *port)
859 {
860 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
861
862 return uart->port.type == PORT_BFIN ? "BFIN-UART" : NULL;
863 }
864
865 /*
866 * Release the memory region(s) being used by 'port'.
867 */
868 static void bfin_serial_release_port(struct uart_port *port)
869 {
870 }
871
872 /*
873 * Request the memory region(s) being used by 'port'.
874 */
875 static int bfin_serial_request_port(struct uart_port *port)
876 {
877 return 0;
878 }
879
880 /*
881 * Configure/autoconfigure the port.
882 */
883 static void bfin_serial_config_port(struct uart_port *port, int flags)
884 {
885 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
886
887 if (flags & UART_CONFIG_TYPE &&
888 bfin_serial_request_port(&uart->port) == 0)
889 uart->port.type = PORT_BFIN;
890 }
891
892 /*
893 * Verify the new serial_struct (for TIOCSSERIAL).
894 * The only change we allow are to the flags and type, and
895 * even then only between PORT_BFIN and PORT_UNKNOWN
896 */
897 static int
898 bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
899 {
900 return 0;
901 }
902
903 /*
904 * Enable the IrDA function if tty->ldisc.num is N_IRDA.
905 * In other cases, disable IrDA function.
906 */
907 static void bfin_serial_set_ldisc(struct uart_port *port)
908 {
909 int line = port->line;
910 unsigned short val;
911
912 if (line >= port->info->port.tty->driver->num)
913 return;
914
915 switch (port->info->port.tty->termios->c_line) {
916 case N_IRDA:
917 val = UART_GET_GCTL(&bfin_serial_ports[line]);
918 val |= (IREN | RPOLC);
919 UART_PUT_GCTL(&bfin_serial_ports[line], val);
920 break;
921 default:
922 val = UART_GET_GCTL(&bfin_serial_ports[line]);
923 val &= ~(IREN | RPOLC);
924 UART_PUT_GCTL(&bfin_serial_ports[line], val);
925 }
926 }
927
928 static void bfin_serial_reset_irda(struct uart_port *port)
929 {
930 int line = port->line;
931 unsigned short val;
932
933 val = UART_GET_GCTL(&bfin_serial_ports[line]);
934 val &= ~(IREN | RPOLC);
935 UART_PUT_GCTL(&bfin_serial_ports[line], val);
936 SSYNC();
937 val |= (IREN | RPOLC);
938 UART_PUT_GCTL(&bfin_serial_ports[line], val);
939 SSYNC();
940 }
941
942 #ifdef CONFIG_CONSOLE_POLL
943 static void bfin_serial_poll_put_char(struct uart_port *port, unsigned char chr)
944 {
945 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
946
947 while (!(UART_GET_LSR(uart) & THRE))
948 cpu_relax();
949
950 UART_CLEAR_DLAB(uart);
951 UART_PUT_CHAR(uart, (unsigned char)chr);
952 }
953
954 static int bfin_serial_poll_get_char(struct uart_port *port)
955 {
956 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
957 unsigned char chr;
958
959 while (!(UART_GET_LSR(uart) & DR))
960 cpu_relax();
961
962 UART_CLEAR_DLAB(uart);
963 chr = UART_GET_CHAR(uart);
964
965 return chr;
966 }
967 #endif
968
969 #if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
970 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
971 static void bfin_kgdboc_port_shutdown(struct uart_port *port)
972 {
973 if (kgdboc_break_enabled) {
974 kgdboc_break_enabled = 0;
975 bfin_serial_shutdown(port);
976 }
977 }
978
979 static int bfin_kgdboc_port_startup(struct uart_port *port)
980 {
981 kgdboc_port_line = port->line;
982 kgdboc_break_enabled = !bfin_serial_startup(port);
983 return 0;
984 }
985 #endif
986
987 static struct uart_ops bfin_serial_pops = {
988 .tx_empty = bfin_serial_tx_empty,
989 .set_mctrl = bfin_serial_set_mctrl,
990 .get_mctrl = bfin_serial_get_mctrl,
991 .stop_tx = bfin_serial_stop_tx,
992 .start_tx = bfin_serial_start_tx,
993 .stop_rx = bfin_serial_stop_rx,
994 .enable_ms = bfin_serial_enable_ms,
995 .break_ctl = bfin_serial_break_ctl,
996 .startup = bfin_serial_startup,
997 .shutdown = bfin_serial_shutdown,
998 .set_termios = bfin_serial_set_termios,
999 .set_ldisc = bfin_serial_set_ldisc,
1000 .type = bfin_serial_type,
1001 .release_port = bfin_serial_release_port,
1002 .request_port = bfin_serial_request_port,
1003 .config_port = bfin_serial_config_port,
1004 .verify_port = bfin_serial_verify_port,
1005 #if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
1006 defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
1007 .kgdboc_port_startup = bfin_kgdboc_port_startup,
1008 .kgdboc_port_shutdown = bfin_kgdboc_port_shutdown,
1009 #endif
1010 #ifdef CONFIG_CONSOLE_POLL
1011 .poll_put_char = bfin_serial_poll_put_char,
1012 .poll_get_char = bfin_serial_poll_get_char,
1013 #endif
1014 };
1015
1016 static void __init bfin_serial_hw_init(void)
1017 {
1018 #ifdef CONFIG_SERIAL_BFIN_UART0
1019 peripheral_request(P_UART0_TX, DRIVER_NAME);
1020 peripheral_request(P_UART0_RX, DRIVER_NAME);
1021 #endif
1022
1023 #ifdef CONFIG_SERIAL_BFIN_UART1
1024 peripheral_request(P_UART1_TX, DRIVER_NAME);
1025 peripheral_request(P_UART1_RX, DRIVER_NAME);
1026
1027 # if defined(CONFIG_BFIN_UART1_CTSRTS) && defined(CONFIG_BF54x)
1028 peripheral_request(P_UART1_RTS, DRIVER_NAME);
1029 peripheral_request(P_UART1_CTS, DRIVER_NAME);
1030 # endif
1031 #endif
1032
1033 #ifdef CONFIG_SERIAL_BFIN_UART2
1034 peripheral_request(P_UART2_TX, DRIVER_NAME);
1035 peripheral_request(P_UART2_RX, DRIVER_NAME);
1036 #endif
1037
1038 #ifdef CONFIG_SERIAL_BFIN_UART3
1039 peripheral_request(P_UART3_TX, DRIVER_NAME);
1040 peripheral_request(P_UART3_RX, DRIVER_NAME);
1041
1042 # if defined(CONFIG_BFIN_UART3_CTSRTS) && defined(CONFIG_BF54x)
1043 peripheral_request(P_UART3_RTS, DRIVER_NAME);
1044 peripheral_request(P_UART3_CTS, DRIVER_NAME);
1045 # endif
1046 #endif
1047 }
1048
1049 static void __init bfin_serial_init_ports(void)
1050 {
1051 static int first = 1;
1052 int i;
1053
1054 if (!first)
1055 return;
1056 first = 0;
1057
1058 bfin_serial_hw_init();
1059
1060 for (i = 0; i < nr_active_ports; i++) {
1061 bfin_serial_ports[i].port.uartclk = get_sclk();
1062 bfin_serial_ports[i].port.fifosize = BFIN_UART_TX_FIFO_SIZE;
1063 bfin_serial_ports[i].port.ops = &bfin_serial_pops;
1064 bfin_serial_ports[i].port.line = i;
1065 bfin_serial_ports[i].port.iotype = UPIO_MEM;
1066 bfin_serial_ports[i].port.membase =
1067 (void __iomem *)bfin_serial_resource[i].uart_base_addr;
1068 bfin_serial_ports[i].port.mapbase =
1069 bfin_serial_resource[i].uart_base_addr;
1070 bfin_serial_ports[i].port.irq =
1071 bfin_serial_resource[i].uart_irq;
1072 bfin_serial_ports[i].status_irq =
1073 bfin_serial_resource[i].uart_status_irq;
1074 bfin_serial_ports[i].port.flags = UPF_BOOT_AUTOCONF;
1075 #ifdef CONFIG_SERIAL_BFIN_DMA
1076 bfin_serial_ports[i].tx_done = 1;
1077 bfin_serial_ports[i].tx_count = 0;
1078 bfin_serial_ports[i].tx_dma_channel =
1079 bfin_serial_resource[i].uart_tx_dma_channel;
1080 bfin_serial_ports[i].rx_dma_channel =
1081 bfin_serial_resource[i].uart_rx_dma_channel;
1082 init_timer(&(bfin_serial_ports[i].rx_dma_timer));
1083 #endif
1084 #if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
1085 defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
1086 bfin_serial_ports[i].cts_pin =
1087 bfin_serial_resource[i].uart_cts_pin;
1088 bfin_serial_ports[i].rts_pin =
1089 bfin_serial_resource[i].uart_rts_pin;
1090 #endif
1091 }
1092 }
1093
1094 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
1095 /*
1096 * If the port was already initialised (eg, by a boot loader),
1097 * try to determine the current setup.
1098 */
1099 static void __init
1100 bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud,
1101 int *parity, int *bits)
1102 {
1103 unsigned short status;
1104
1105 status = UART_GET_IER(uart) & (ERBFI | ETBEI);
1106 if (status == (ERBFI | ETBEI)) {
1107 /* ok, the port was enabled */
1108 u16 lcr, dlh, dll;
1109
1110 lcr = UART_GET_LCR(uart);
1111
1112 *parity = 'n';
1113 if (lcr & PEN) {
1114 if (lcr & EPS)
1115 *parity = 'e';
1116 else
1117 *parity = 'o';
1118 }
1119 switch (lcr & 0x03) {
1120 case 0: *bits = 5; break;
1121 case 1: *bits = 6; break;
1122 case 2: *bits = 7; break;
1123 case 3: *bits = 8; break;
1124 }
1125 /* Set DLAB in LCR to Access DLL and DLH */
1126 UART_SET_DLAB(uart);
1127
1128 dll = UART_GET_DLL(uart);
1129 dlh = UART_GET_DLH(uart);
1130
1131 /* Clear DLAB in LCR to Access THR RBR IER */
1132 UART_CLEAR_DLAB(uart);
1133
1134 *baud = get_sclk() / (16*(dll | dlh << 8));
1135 }
1136 pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __func__, *baud, *parity, *bits);
1137 }
1138
1139 static struct uart_driver bfin_serial_reg;
1140
1141 static int __init
1142 bfin_serial_console_setup(struct console *co, char *options)
1143 {
1144 struct bfin_serial_port *uart;
1145 int baud = 57600;
1146 int bits = 8;
1147 int parity = 'n';
1148 # if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
1149 defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
1150 int flow = 'r';
1151 # else
1152 int flow = 'n';
1153 # endif
1154
1155 /*
1156 * Check whether an invalid uart number has been specified, and
1157 * if so, search for the first available port that does have
1158 * console support.
1159 */
1160 if (co->index == -1 || co->index >= nr_active_ports)
1161 co->index = 0;
1162 uart = &bfin_serial_ports[co->index];
1163
1164 if (options)
1165 uart_parse_options(options, &baud, &parity, &bits, &flow);
1166 else
1167 bfin_serial_console_get_options(uart, &baud, &parity, &bits);
1168
1169 return uart_set_options(&uart->port, co, baud, parity, bits, flow);
1170 }
1171 #endif /* defined (CONFIG_SERIAL_BFIN_CONSOLE) ||
1172 defined (CONFIG_EARLY_PRINTK) */
1173
1174 #ifdef CONFIG_SERIAL_BFIN_CONSOLE
1175 static void bfin_serial_console_putchar(struct uart_port *port, int ch)
1176 {
1177 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
1178 while (!(UART_GET_LSR(uart) & THRE))
1179 barrier();
1180 UART_PUT_CHAR(uart, ch);
1181 SSYNC();
1182 }
1183
1184 /*
1185 * Interrupts are disabled on entering
1186 */
1187 static void
1188 bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
1189 {
1190 struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
1191 unsigned long flags;
1192
1193 spin_lock_irqsave(&uart->port.lock, flags);
1194 uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
1195 spin_unlock_irqrestore(&uart->port.lock, flags);
1196
1197 }
1198
1199 static struct console bfin_serial_console = {
1200 .name = BFIN_SERIAL_NAME,
1201 .write = bfin_serial_console_write,
1202 .device = uart_console_device,
1203 .setup = bfin_serial_console_setup,
1204 .flags = CON_PRINTBUFFER,
1205 .index = -1,
1206 .data = &bfin_serial_reg,
1207 };
1208
1209 static int __init bfin_serial_rs_console_init(void)
1210 {
1211 bfin_serial_init_ports();
1212 register_console(&bfin_serial_console);
1213
1214 return 0;
1215 }
1216 console_initcall(bfin_serial_rs_console_init);
1217
1218 #define BFIN_SERIAL_CONSOLE &bfin_serial_console
1219 #else
1220 #define BFIN_SERIAL_CONSOLE NULL
1221 #endif /* CONFIG_SERIAL_BFIN_CONSOLE */
1222
1223
1224 #ifdef CONFIG_EARLY_PRINTK
1225 static __init void early_serial_putc(struct uart_port *port, int ch)
1226 {
1227 unsigned timeout = 0xffff;
1228 struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
1229
1230 while ((!(UART_GET_LSR(uart) & THRE)) && --timeout)
1231 cpu_relax();
1232 UART_PUT_CHAR(uart, ch);
1233 }
1234
1235 static __init void early_serial_write(struct console *con, const char *s,
1236 unsigned int n)
1237 {
1238 struct bfin_serial_port *uart = &bfin_serial_ports[con->index];
1239 unsigned int i;
1240
1241 for (i = 0; i < n; i++, s++) {
1242 if (*s == '\n')
1243 early_serial_putc(&uart->port, '\r');
1244 early_serial_putc(&uart->port, *s);
1245 }
1246 }
1247
1248 static struct __initdata console bfin_early_serial_console = {
1249 .name = "early_BFuart",
1250 .write = early_serial_write,
1251 .device = uart_console_device,
1252 .flags = CON_PRINTBUFFER,
1253 .setup = bfin_serial_console_setup,
1254 .index = -1,
1255 .data = &bfin_serial_reg,
1256 };
1257
1258 struct console __init *bfin_earlyserial_init(unsigned int port,
1259 unsigned int cflag)
1260 {
1261 struct bfin_serial_port *uart;
1262 struct ktermios t;
1263
1264 if (port == -1 || port >= nr_active_ports)
1265 port = 0;
1266 bfin_serial_init_ports();
1267 bfin_early_serial_console.index = port;
1268 uart = &bfin_serial_ports[port];
1269 t.c_cflag = cflag;
1270 t.c_iflag = 0;
1271 t.c_oflag = 0;
1272 t.c_lflag = ICANON;
1273 t.c_line = port;
1274 bfin_serial_set_termios(&uart->port, &t, &t);
1275 return &bfin_early_serial_console;
1276 }
1277
1278 #endif /* CONFIG_EARLY_PRINTK */
1279
1280 static struct uart_driver bfin_serial_reg = {
1281 .owner = THIS_MODULE,
1282 .driver_name = "bfin-uart",
1283 .dev_name = BFIN_SERIAL_NAME,
1284 .major = BFIN_SERIAL_MAJOR,
1285 .minor = BFIN_SERIAL_MINOR,
1286 .nr = BFIN_UART_NR_PORTS,
1287 .cons = BFIN_SERIAL_CONSOLE,
1288 };
1289
1290 static int bfin_serial_suspend(struct platform_device *dev, pm_message_t state)
1291 {
1292 int i;
1293
1294 for (i = 0; i < nr_active_ports; i++) {
1295 if (bfin_serial_ports[i].port.dev != &dev->dev)
1296 continue;
1297 uart_suspend_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
1298 }
1299
1300 return 0;
1301 }
1302
1303 static int bfin_serial_resume(struct platform_device *dev)
1304 {
1305 int i;
1306
1307 for (i = 0; i < nr_active_ports; i++) {
1308 if (bfin_serial_ports[i].port.dev != &dev->dev)
1309 continue;
1310 uart_resume_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
1311 }
1312
1313 return 0;
1314 }
1315
1316 static int bfin_serial_probe(struct platform_device *dev)
1317 {
1318 struct resource *res = dev->resource;
1319 int i;
1320
1321 for (i = 0; i < dev->num_resources; i++, res++)
1322 if (res->flags & IORESOURCE_MEM)
1323 break;
1324
1325 if (i < dev->num_resources) {
1326 for (i = 0; i < nr_active_ports; i++, res++) {
1327 if (bfin_serial_ports[i].port.mapbase != res->start)
1328 continue;
1329 bfin_serial_ports[i].port.dev = &dev->dev;
1330 uart_add_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
1331 }
1332 }
1333
1334 return 0;
1335 }
1336
1337 static int bfin_serial_remove(struct platform_device *dev)
1338 {
1339 int i;
1340
1341 for (i = 0; i < nr_active_ports; i++) {
1342 if (bfin_serial_ports[i].port.dev != &dev->dev)
1343 continue;
1344 uart_remove_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
1345 bfin_serial_ports[i].port.dev = NULL;
1346 #if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
1347 defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
1348 gpio_free(bfin_serial_ports[i].cts_pin);
1349 gpio_free(bfin_serial_ports[i].rts_pin);
1350 #endif
1351 }
1352
1353 return 0;
1354 }
1355
1356 static struct platform_driver bfin_serial_driver = {
1357 .probe = bfin_serial_probe,
1358 .remove = bfin_serial_remove,
1359 .suspend = bfin_serial_suspend,
1360 .resume = bfin_serial_resume,
1361 .driver = {
1362 .name = "bfin-uart",
1363 .owner = THIS_MODULE,
1364 },
1365 };
1366
1367 static int __init bfin_serial_init(void)
1368 {
1369 int ret;
1370
1371 pr_info("Serial: Blackfin serial driver\n");
1372
1373 bfin_serial_init_ports();
1374
1375 ret = uart_register_driver(&bfin_serial_reg);
1376 if (ret == 0) {
1377 ret = platform_driver_register(&bfin_serial_driver);
1378 if (ret) {
1379 pr_debug("uart register failed\n");
1380 uart_unregister_driver(&bfin_serial_reg);
1381 }
1382 }
1383 return ret;
1384 }
1385
1386 static void __exit bfin_serial_exit(void)
1387 {
1388 platform_driver_unregister(&bfin_serial_driver);
1389 uart_unregister_driver(&bfin_serial_reg);
1390 }
1391
1392
1393 module_init(bfin_serial_init);
1394 module_exit(bfin_serial_exit);
1395
1396 MODULE_AUTHOR("Aubrey.Li <aubrey.li@analog.com>");
1397 MODULE_DESCRIPTION("Blackfin generic serial port driver");
1398 MODULE_LICENSE("GPL");
1399 MODULE_ALIAS_CHARDEV_MAJOR(BFIN_SERIAL_MAJOR);
1400 MODULE_ALIAS("platform:bfin-uart");
Linux 2.6 ibm-acpi/thinkpad-acpi driver git tree