arch/blackfin/mach-bf537/boards/cm_bf537e.c

   1 /*
   2  * Copyright 2004-2009 Analog Devices Inc.
   3  *           2008-2009 Bluetechnix
   4  *                2005 National ICT Australia (NICTA)
   5  *                      Aidan Williams <aidan@nicta.com.au>
   6  *
   7  * Licensed under the GPL-2 or later.
   8  */
   9
  10 #include <linux/device.h>
  11 #include <linux/etherdevice.h>
  12 #include <linux/platform_device.h>
  13 #include <linux/mtd/mtd.h>
  14 #include <linux/mtd/partitions.h>
  15 #include <linux/mtd/physmap.h>
  16 #include <linux/spi/spi.h>
  17 #include <linux/spi/flash.h>
  18 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
  19 #include <linux/usb/isp1362.h>
  20 #endif
  21 #include <linux/ata_platform.h>
  22 #include <linux/irq.h>
  23 #include <asm/dma.h>
  24 #include <asm/bfin5xx_spi.h>
  25 #include <asm/portmux.h>
  26 #include <asm/dpmc.h>
  27
  28 /*
  29  * Name the Board for the /proc/cpuinfo
  30  */
  31 const char bfin_board_name[] = "Bluetechnix CM BF537E";
  32
  33 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
  34 /* all SPI peripherals info goes here */
  35
  36 #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
  37 static struct mtd_partition bfin_spi_flash_partitions[] = {
  38         {
  39                 .name = "bootloader(spi)",
  40                 .size = 0x00020000,
  41                 .offset = 0,
  42                 .mask_flags = MTD_CAP_ROM
  43         }, {
  44                 .name = "linux kernel(spi)",
  45                 .size = 0xe0000,
  46                 .offset = 0x20000
  47         }, {
  48                 .name = "file system(spi)",
  49                 .size = 0x700000,
  50                 .offset = 0x00100000,
  51         }
  52 };
  53
  54 static struct flash_platform_data bfin_spi_flash_data = {
  55         .name = "m25p80",
  56         .parts = bfin_spi_flash_partitions,
  57         .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
  58         .type = "m25p64",
  59 };
  60
  61 /* SPI flash chip (m25p64) */
  62 static struct bfin5xx_spi_chip spi_flash_chip_info = {
  63         .enable_dma = 0,         /* use dma transfer with this chip*/
  64         .bits_per_word = 8,
  65 };
  66 #endif
  67
  68 #if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
  69 /* SPI ADC chip */
  70 static struct bfin5xx_spi_chip spi_adc_chip_info = {
  71         .enable_dma = 1,         /* use dma transfer with this chip*/
  72         .bits_per_word = 16,
  73 };
  74 #endif
  75
  76 #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
  77 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
  78         .enable_dma = 0,
  79         .bits_per_word = 16,
  80 };
  81 #endif
  82
  83 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
  84 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
  85         .enable_dma = 0,
  86         .bits_per_word = 8,
  87 };
  88 #endif
  89
  90 static struct spi_board_info bfin_spi_board_info[] __initdata = {
  91 #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
  92         {
  93                 /* the modalias must be the same as spi device driver name */
  94                 .modalias = "m25p80", /* Name of spi_driver for this device */
  95                 .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
  96                 .bus_num = 0, /* Framework bus number */
  97                 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
  98                 .platform_data = &bfin_spi_flash_data,
  99                 .controller_data = &spi_flash_chip_info,
 100                 .mode = SPI_MODE_3,
 101         },
 102 #endif
 103
 104 #if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 105         {
 106                 .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
 107                 .max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
 108                 .bus_num = 0, /* Framework bus number */
 109                 .chip_select = 1, /* Framework chip select. */
 110                 .platform_data = NULL, /* No spi_driver specific config */
 111                 .controller_data = &spi_adc_chip_info,
 112         },
 113 #endif
 114
 115 #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 116         {
 117                 .modalias = "ad1836",
 118                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 119                 .bus_num = 0,
 120                 .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
 121                 .controller_data = &ad1836_spi_chip_info,
 122         },
 123 #endif
 124
 125 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 126         {
 127                 .modalias = "mmc_spi",
 128                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 129                 .bus_num = 0,
 130                 .chip_select = 1,
 131                 .controller_data = &mmc_spi_chip_info,
 132                 .mode = SPI_MODE_3,
 133         },
 134 #endif
 135 };
 136
 137 /* SPI (0) */
 138 static struct resource bfin_spi0_resource[] = {
 139         [0] = {
 140                 .start = SPI0_REGBASE,
 141                 .end   = SPI0_REGBASE + 0xFF,
 142                 .flags = IORESOURCE_MEM,
 143                 },
 144         [1] = {
 145                 .start = CH_SPI,
 146                 .end   = CH_SPI,
 147                 .flags = IORESOURCE_DMA,
 148         },
 149         [2] = {
 150                 .start = IRQ_SPI,
 151                 .end   = IRQ_SPI,
 152                 .flags = IORESOURCE_IRQ,
 153         },
 154 };
 155
 156 /* SPI controller data */
 157 static struct bfin5xx_spi_master bfin_spi0_info = {
 158         .num_chipselect = 8,
 159         .enable_dma = 1,  /* master has the ability to do dma transfer */
 160         .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 161 };
 162
 163 static struct platform_device bfin_spi0_device = {
 164         .name = "bfin-spi",
 165         .id = 0, /* Bus number */
 166         .num_resources = ARRAY_SIZE(bfin_spi0_resource),
 167         .resource = bfin_spi0_resource,
 168         .dev = {
 169                 .platform_data = &bfin_spi0_info, /* Passed to driver */
 170         },
 171 };
 172 #endif  /* spi master and devices */
 173
 174 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 175 static struct platform_device rtc_device = {
 176         .name = "rtc-bfin",
 177         .id   = -1,
 178 };
 179 #endif
 180
 181 #if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
 182 static struct platform_device hitachi_fb_device = {
 183         .name = "hitachi-tx09",
 184 };
 185 #endif
 186
 187 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 188 #include <linux/smc91x.h>
 189
 190 static struct smc91x_platdata smc91x_info = {
 191         .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 192         .leda = RPC_LED_100_10,
 193         .ledb = RPC_LED_TX_RX,
 194 };
 195
 196 static struct resource smc91x_resources[] = {
 197         {
 198                 .start = 0x20200300,
 199                 .end = 0x20200300 + 16,
 200                 .flags = IORESOURCE_MEM,
 201         }, {
 202                 .start = IRQ_PF14,
 203                 .end = IRQ_PF14,
 204                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 205                 },
 206 };
 207
 208 static struct platform_device smc91x_device = {
 209         .name = "smc91x",
 210         .id = 0,
 211         .num_resources = ARRAY_SIZE(smc91x_resources),
 212         .resource = smc91x_resources,
 213         .dev    = {
 214                 .platform_data  = &smc91x_info,
 215         },
 216 };
 217 #endif
 218
 219 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 220 static struct resource isp1362_hcd_resources[] = {
 221         {
 222                 .start = 0x20308000,
 223                 .end = 0x20308000,
 224                 .flags = IORESOURCE_MEM,
 225         }, {
 226                 .start = 0x20308004,
 227                 .end = 0x20308004,
 228                 .flags = IORESOURCE_MEM,
 229         }, {
 230                 .start = IRQ_PG15,
 231                 .end = IRQ_PG15,
 232                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 233         },
 234 };
 235
 236 static struct isp1362_platform_data isp1362_priv = {
 237         .sel15Kres = 1,
 238         .clknotstop = 0,
 239         .oc_enable = 0,
 240         .int_act_high = 0,
 241         .int_edge_triggered = 0,
 242         .remote_wakeup_connected = 0,
 243         .no_power_switching = 1,
 244         .power_switching_mode = 0,
 245 };
 246
 247 static struct platform_device isp1362_hcd_device = {
 248         .name = "isp1362-hcd",
 249         .id = 0,
 250         .dev = {
 251                 .platform_data = &isp1362_priv,
 252         },
 253         .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
 254         .resource = isp1362_hcd_resources,
 255 };
 256 #endif
 257
 258 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 259 static struct resource net2272_bfin_resources[] = {
 260         {
 261                 .start = 0x20300000,
 262                 .end = 0x20300000 + 0x100,
 263                 .flags = IORESOURCE_MEM,
 264         }, {
 265                 .start = IRQ_PG13,
 266                 .end = IRQ_PG13,
 267                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 268         },
 269 };
 270
 271 static struct platform_device net2272_bfin_device = {
 272         .name = "net2272",
 273         .id = -1,
 274         .num_resources = ARRAY_SIZE(net2272_bfin_resources),
 275         .resource = net2272_bfin_resources,
 276 };
 277 #endif
 278
 279 #if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
 280 static struct mtd_partition cm_partitions[] = {
 281         {
 282                 .name   = "bootloader(nor)",
 283                 .size   = 0x40000,
 284                 .offset = 0,
 285         }, {
 286                 .name   = "linux kernel(nor)",
 287                 .size   = 0x100000,
 288                 .offset = MTDPART_OFS_APPEND,
 289         }, {
 290                 .name   = "file system(nor)",
 291                 .size   = MTDPART_SIZ_FULL,
 292                 .offset = MTDPART_OFS_APPEND,
 293         }
 294 };
 295
 296 static struct physmap_flash_data cm_flash_data = {
 297         .width    = 2,
 298         .parts    = cm_partitions,
 299         .nr_parts = ARRAY_SIZE(cm_partitions),
 300 };
 301
 302 static unsigned cm_flash_gpios[] = { GPIO_PF4 };
 303
 304 static struct resource cm_flash_resource[] = {
 305         {
 306                 .name  = "cfi_probe",
 307                 .start = 0x20000000,
 308                 .end   = 0x201fffff,
 309                 .flags = IORESOURCE_MEM,
 310         }, {
 311                 .start = (unsigned long)cm_flash_gpios,
 312                 .end   = ARRAY_SIZE(cm_flash_gpios),
 313                 .flags = IORESOURCE_IRQ,
 314         }
 315 };
 316
 317 static struct platform_device cm_flash_device = {
 318         .name          = "gpio-addr-flash",
 319         .id            = 0,
 320         .dev = {
 321                 .platform_data = &cm_flash_data,
 322         },
 323         .num_resources = ARRAY_SIZE(cm_flash_resource),
 324         .resource      = cm_flash_resource,
 325 };
 326 #endif
 327
 328 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
 329 #ifdef CONFIG_SERIAL_BFIN_UART0
 330 static struct resource bfin_uart0_resources[] = {
 331         {
 332                 .start = 0xFFC00400,
 333                 .end = 0xFFC004FF,
 334                 .flags = IORESOURCE_MEM,
 335         },
 336         {
 337                 .start = IRQ_UART0_RX,
 338                 .end = IRQ_UART0_RX+1,
 339                 .flags = IORESOURCE_IRQ,
 340         },
 341         {
 342                 .start = IRQ_UART0_ERROR,
 343                 .end = IRQ_UART0_ERROR,
 344                 .flags = IORESOURCE_IRQ,
 345         },
 346         {
 347                 .start = CH_UART0_TX,
 348                 .end = CH_UART0_TX,
 349                 .flags = IORESOURCE_DMA,
 350         },
 351         {
 352                 .start = CH_UART0_RX,
 353                 .end = CH_UART0_RX,
 354                 .flags = IORESOURCE_DMA,
 355         },
 356 #ifdef CONFIG_BFIN_UART0_CTSRTS
 357         {
 358                 /*
 359                  * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
 360                  */
 361                 .start = -1,
 362                 .end = -1,
 363                 .flags = IORESOURCE_IO,
 364         },
 365         {
 366                 /*
 367                  * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
 368                  */
 369                 .start = -1,
 370                 .end = -1,
 371                 .flags = IORESOURCE_IO,
 372         },
 373 #endif
 374 };
 375
 376 static struct platform_device bfin_uart0_device = {
 377         .name = "bfin-uart",
 378         .id = 0,
 379         .num_resources = ARRAY_SIZE(bfin_uart0_resources),
 380         .resource = bfin_uart0_resources,
 381 };
 382 #endif
 383 #ifdef CONFIG_SERIAL_BFIN_UART1
 384 static struct resource bfin_uart1_resources[] = {
 385         {
 386                 .start = 0xFFC02000,
 387                 .end = 0xFFC020FF,
 388                 .flags = IORESOURCE_MEM,
 389         },
 390         {
 391                 .start = IRQ_UART1_RX,
 392                 .end = IRQ_UART1_RX+1,
 393                 .flags = IORESOURCE_IRQ,
 394         },
 395         {
 396                 .start = IRQ_UART1_ERROR,
 397                 .end = IRQ_UART1_ERROR,
 398                 .flags = IORESOURCE_IRQ,
 399         },
 400         {
 401                 .start = CH_UART1_TX,
 402                 .end = CH_UART1_TX,
 403                 .flags = IORESOURCE_DMA,
 404         },
 405         {
 406                 .start = CH_UART1_RX,
 407                 .end = CH_UART1_RX,
 408                 .flags = IORESOURCE_DMA,
 409         },
 410 #ifdef CONFIG_BFIN_UART1_CTSRTS
 411         {
 412                 /*
 413                  * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
 414                  */
 415                 .start = -1,
 416                 .end = -1,
 417                 .flags = IORESOURCE_IO,
 418         },
 419         {
 420                 /*
 421                  * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
 422                  */
 423                 .start = -1,
 424                 .end = -1,
 425                 .flags = IORESOURCE_IO,
 426         },
 427 #endif
 428 };
 429
 430 static struct platform_device bfin_uart1_device = {
 431         .name = "bfin-uart",
 432         .id = 1,
 433         .num_resources = ARRAY_SIZE(bfin_uart1_resources),
 434         .resource = bfin_uart1_resources,
 435 };
 436 #endif
 437 #endif
 438
 439 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 440 #ifdef CONFIG_BFIN_SIR0
 441 static struct resource bfin_sir0_resources[] = {
 442         {
 443                 .start = 0xFFC00400,
 444                 .end = 0xFFC004FF,
 445                 .flags = IORESOURCE_MEM,
 446         },
 447         {
 448                 .start = IRQ_UART0_RX,
 449                 .end = IRQ_UART0_RX+1,
 450                 .flags = IORESOURCE_IRQ,
 451         },
 452         {
 453                 .start = CH_UART0_RX,
 454                 .end = CH_UART0_RX+1,
 455                 .flags = IORESOURCE_DMA,
 456         },
 457 };
 458 static struct platform_device bfin_sir0_device = {
 459         .name = "bfin_sir",
 460         .id = 0,
 461         .num_resources = ARRAY_SIZE(bfin_sir0_resources),
 462         .resource = bfin_sir0_resources,
 463 };
 464 #endif
 465 #ifdef CONFIG_BFIN_SIR1
 466 static struct resource bfin_sir1_resources[] = {
 467         {
 468                 .start = 0xFFC02000,
 469                 .end = 0xFFC020FF,
 470                 .flags = IORESOURCE_MEM,
 471         },
 472         {
 473                 .start = IRQ_UART1_RX,
 474                 .end = IRQ_UART1_RX+1,
 475                 .flags = IORESOURCE_IRQ,
 476         },
 477         {
 478                 .start = CH_UART1_RX,
 479                 .end = CH_UART1_RX+1,
 480                 .flags = IORESOURCE_DMA,
 481         },
 482 };
 483 static struct platform_device bfin_sir1_device = {
 484         .name = "bfin_sir",
 485         .id = 1,
 486         .num_resources = ARRAY_SIZE(bfin_sir1_resources),
 487         .resource = bfin_sir1_resources,
 488 };
 489 #endif
 490 #endif
 491
 492 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 493 static struct resource bfin_twi0_resource[] = {
 494         [0] = {
 495                 .start = TWI0_REGBASE,
 496                 .end   = TWI0_REGBASE,
 497                 .flags = IORESOURCE_MEM,
 498         },
 499         [1] = {
 500                 .start = IRQ_TWI,
 501                 .end   = IRQ_TWI,
 502                 .flags = IORESOURCE_IRQ,
 503         },
 504 };
 505
 506 static struct platform_device i2c_bfin_twi_device = {
 507         .name = "i2c-bfin-twi",
 508         .id = 0,
 509         .num_resources = ARRAY_SIZE(bfin_twi0_resource),
 510         .resource = bfin_twi0_resource,
 511 };
 512 #endif
 513
 514 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
 515 static struct platform_device bfin_sport0_uart_device = {
 516         .name = "bfin-sport-uart",
 517         .id = 0,
 518 };
 519
 520 static struct platform_device bfin_sport1_uart_device = {
 521         .name = "bfin-sport-uart",
 522         .id = 1,
 523 };
 524 #endif
 525
 526 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 527 static struct platform_device bfin_mii_bus = {
 528         .name = "bfin_mii_bus",
 529 };
 530
 531 static struct platform_device bfin_mac_device = {
 532         .name = "bfin_mac",
 533         .dev.platform_data = &bfin_mii_bus,
 534 };
 535 #endif
 536
 537 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
 538 #define PATA_INT        IRQ_PF14
 539
 540 static struct pata_platform_info bfin_pata_platform_data = {
 541         .ioport_shift = 2,
 542         .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
 543 };
 544
 545 static struct resource bfin_pata_resources[] = {
 546         {
 547                 .start = 0x2030C000,
 548                 .end = 0x2030C01F,
 549                 .flags = IORESOURCE_MEM,
 550         },
 551         {
 552                 .start = 0x2030D018,
 553                 .end = 0x2030D01B,
 554                 .flags = IORESOURCE_MEM,
 555         },
 556         {
 557                 .start = PATA_INT,
 558                 .end = PATA_INT,
 559                 .flags = IORESOURCE_IRQ,
 560         },
 561 };
 562
 563 static struct platform_device bfin_pata_device = {
 564         .name = "pata_platform",
 565         .id = -1,
 566         .num_resources = ARRAY_SIZE(bfin_pata_resources),
 567         .resource = bfin_pata_resources,
 568         .dev = {
 569                 .platform_data = &bfin_pata_platform_data,
 570         }
 571 };
 572 #endif
 573
 574 static const unsigned int cclk_vlev_datasheet[] =
 575 {
 576         VRPAIR(VLEV_085, 250000000),
 577         VRPAIR(VLEV_090, 376000000),
 578         VRPAIR(VLEV_095, 426000000),
 579         VRPAIR(VLEV_100, 426000000),
 580         VRPAIR(VLEV_105, 476000000),
 581         VRPAIR(VLEV_110, 476000000),
 582         VRPAIR(VLEV_115, 476000000),
 583         VRPAIR(VLEV_120, 500000000),
 584         VRPAIR(VLEV_125, 533000000),
 585         VRPAIR(VLEV_130, 600000000),
 586 };
 587
 588 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
 589         .tuple_tab = cclk_vlev_datasheet,
 590         .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
 591         .vr_settling_time = 25 /* us */,
 592 };
 593
 594 static struct platform_device bfin_dpmc = {
 595         .name = "bfin dpmc",
 596         .dev = {
 597                 .platform_data = &bfin_dmpc_vreg_data,
 598         },
 599 };
 600
 601 static struct platform_device *cm_bf537e_devices[] __initdata = {
 602
 603         &bfin_dpmc,
 604
 605 #if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
 606         &hitachi_fb_device,
 607 #endif
 608
 609 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 610         &rtc_device,
 611 #endif
 612
 613 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
 614 #ifdef CONFIG_SERIAL_BFIN_UART0
 615         &bfin_uart0_device,
 616 #endif
 617 #ifdef CONFIG_SERIAL_BFIN_UART1
 618         &bfin_uart1_device,
 619 #endif
 620 #endif
 621
 622 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 623 #ifdef CONFIG_BFIN_SIR0
 624         &bfin_sir0_device,
 625 #endif
 626 #ifdef CONFIG_BFIN_SIR1
 627         &bfin_sir1_device,
 628 #endif
 629 #endif
 630
 631 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 632         &i2c_bfin_twi_device,
 633 #endif
 634
 635 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
 636         &bfin_sport0_uart_device,
 637         &bfin_sport1_uart_device,
 638 #endif
 639
 640 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 641         &isp1362_hcd_device,
 642 #endif
 643
 644 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 645         &smc91x_device,
 646 #endif
 647
 648 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 649         &bfin_mii_bus,
 650         &bfin_mac_device,
 651 #endif
 652
 653 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 654         &net2272_bfin_device,
 655 #endif
 656
 657 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 658         &bfin_spi0_device,
 659 #endif
 660
 661 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
 662         &bfin_pata_device,
 663 #endif
 664
 665 #if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
 666         &cm_flash_device,
 667 #endif
 668 };
 669
 670 static int __init cm_bf537e_init(void)
 671 {
 672         printk(KERN_INFO "%s(): registering device resources\n", __func__);
 673         platform_add_devices(cm_bf537e_devices, ARRAY_SIZE(cm_bf537e_devices));
 674 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 675         spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 676 #endif
 677
 678 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
 679         irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
 680 #endif
 681         return 0;
 682 }
 683
 684 arch_initcall(cm_bf537e_init);
 685
 686 void bfin_get_ether_addr(char *addr)
 687 {
 688         random_ether_addr(addr);
 689         printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
 690 }
 691 EXPORT_SYMBOL(bfin_get_ether_addr);