drivers/net/sfc/falcon_boards.c

   1 /****************************************************************************
   2  * Driver for Solarflare Solarstorm network controllers and boards
   3  * Copyright 2007-2009 Solarflare Communications Inc.
   4  *
   5  * This program is free software; you can redistribute it and/or modify it
   6  * under the terms of the GNU General Public License version 2 as published
   7  * by the Free Software Foundation, incorporated herein by reference.
   8  */
   9
  10 #include <linux/rtnetlink.h>
  11
  12 #include "net_driver.h"
  13 #include "phy.h"
  14 #include "efx.h"
  15 #include "nic.h"
  16 #include "workarounds.h"
  17
  18 /* Macros for unpacking the board revision */
  19 /* The revision info is in host byte order. */
  20 #define FALCON_BOARD_TYPE(_rev) (_rev >> 8)
  21 #define FALCON_BOARD_MAJOR(_rev) ((_rev >> 4) & 0xf)
  22 #define FALCON_BOARD_MINOR(_rev) (_rev & 0xf)
  23
  24 /* Board types */
  25 #define FALCON_BOARD_SFE4001 0x01
  26 #define FALCON_BOARD_SFE4002 0x02
  27 #define FALCON_BOARD_SFE4003 0x03
  28 #define FALCON_BOARD_SFN4112F 0x52
  29
  30 /* Board temperature is about 15°C above ambient when air flow is
  31  * limited.  The maximum acceptable ambient temperature varies
  32  * depending on the PHY specifications but the critical temperature
  33  * above which we should shut down to avoid damage is 80°C. */
  34 #define FALCON_BOARD_TEMP_BIAS  15
  35 #define FALCON_BOARD_TEMP_CRIT  (80 + FALCON_BOARD_TEMP_BIAS)
  36
  37 /* SFC4000 datasheet says: 'The maximum permitted junction temperature
  38  * is 125°C; the thermal design of the environment for the SFC4000
  39  * should aim to keep this well below 100°C.' */
  40 #define FALCON_JUNC_TEMP_MIN    0
  41 #define FALCON_JUNC_TEMP_MAX    90
  42 #define FALCON_JUNC_TEMP_CRIT   125
  43
  44 /*****************************************************************************
  45  * Support for LM87 sensor chip used on several boards
  46  */
  47 #define LM87_REG_TEMP_HW_INT_LOCK       0x13
  48 #define LM87_REG_TEMP_HW_EXT_LOCK       0x14
  49 #define LM87_REG_TEMP_HW_INT            0x17
  50 #define LM87_REG_TEMP_HW_EXT            0x18
  51 #define LM87_REG_TEMP_EXT1              0x26
  52 #define LM87_REG_TEMP_INT               0x27
  53 #define LM87_REG_ALARMS1                0x41
  54 #define LM87_REG_ALARMS2                0x42
  55 #define LM87_IN_LIMITS(nr, _min, _max)                  \
  56         0x2B + (nr) * 2, _max, 0x2C + (nr) * 2, _min
  57 #define LM87_AIN_LIMITS(nr, _min, _max)                 \
  58         0x3B + (nr), _max, 0x1A + (nr), _min
  59 #define LM87_TEMP_INT_LIMITS(_min, _max)                \
  60         0x39, _max, 0x3A, _min
  61 #define LM87_TEMP_EXT1_LIMITS(_min, _max)               \
  62         0x37, _max, 0x38, _min
  63
  64 #define LM87_ALARM_TEMP_INT             0x10
  65 #define LM87_ALARM_TEMP_EXT1            0x20
  66
  67 #if defined(CONFIG_SENSORS_LM87) || defined(CONFIG_SENSORS_LM87_MODULE)
  68
  69 static int efx_poke_lm87(struct i2c_client *client, const u8 *reg_values)
  70 {
  71         while (*reg_values) {
  72                 u8 reg = *reg_values++;
  73                 u8 value = *reg_values++;
  74                 int rc = i2c_smbus_write_byte_data(client, reg, value);
  75                 if (rc)
  76                         return rc;
  77         }
  78         return 0;
  79 }
  80
  81 static const u8 falcon_lm87_common_regs[] = {
  82         LM87_REG_TEMP_HW_INT_LOCK, FALCON_BOARD_TEMP_CRIT,
  83         LM87_REG_TEMP_HW_INT, FALCON_BOARD_TEMP_CRIT,
  84         LM87_TEMP_EXT1_LIMITS(FALCON_JUNC_TEMP_MIN, FALCON_JUNC_TEMP_MAX),
  85         LM87_REG_TEMP_HW_EXT_LOCK, FALCON_JUNC_TEMP_CRIT,
  86         LM87_REG_TEMP_HW_EXT, FALCON_JUNC_TEMP_CRIT,
  87         0
  88 };
  89
  90 static int efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info,
  91                          const u8 *reg_values)
  92 {
  93         struct falcon_board *board = falcon_board(efx);
  94         struct i2c_client *client = i2c_new_device(&board->i2c_adap, info);
  95         int rc;
  96
  97         if (!client)
  98                 return -EIO;
  99
 100         /* Read-to-clear alarm/interrupt status */
 101         i2c_smbus_read_byte_data(client, LM87_REG_ALARMS1);
 102         i2c_smbus_read_byte_data(client, LM87_REG_ALARMS2);
 103
 104         rc = efx_poke_lm87(client, reg_values);
 105         if (rc)
 106                 goto err;
 107         rc = efx_poke_lm87(client, falcon_lm87_common_regs);
 108         if (rc)
 109                 goto err;
 110
 111         board->hwmon_client = client;
 112         return 0;
 113
 114 err:
 115         i2c_unregister_device(client);
 116         return rc;
 117 }
 118
 119 static void efx_fini_lm87(struct efx_nic *efx)
 120 {
 121         i2c_unregister_device(falcon_board(efx)->hwmon_client);
 122 }
 123
 124 static int efx_check_lm87(struct efx_nic *efx, unsigned mask)
 125 {
 126         struct i2c_client *client = falcon_board(efx)->hwmon_client;
 127         bool temp_crit, elec_fault, is_failure;
 128         u16 alarms;
 129         s32 reg;
 130
 131         /* If link is up then do not monitor temperature */
 132         if (EFX_WORKAROUND_7884(efx) && efx->link_state.up)
 133                 return 0;
 134
 135         reg = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS1);
 136         if (reg < 0)
 137                 return reg;
 138         alarms = reg;
 139         reg = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS2);
 140         if (reg < 0)
 141                 return reg;
 142         alarms |= reg << 8;
 143         alarms &= mask;
 144
 145         temp_crit = false;
 146         if (alarms & LM87_ALARM_TEMP_INT) {
 147                 reg = i2c_smbus_read_byte_data(client, LM87_REG_TEMP_INT);
 148                 if (reg < 0)
 149                         return reg;
 150                 if (reg > FALCON_BOARD_TEMP_CRIT)
 151                         temp_crit = true;
 152         }
 153         if (alarms & LM87_ALARM_TEMP_EXT1) {
 154                 reg = i2c_smbus_read_byte_data(client, LM87_REG_TEMP_EXT1);
 155                 if (reg < 0)
 156                         return reg;
 157                 if (reg > FALCON_JUNC_TEMP_CRIT)
 158                         temp_crit = true;
 159         }
 160         elec_fault = alarms & ~(LM87_ALARM_TEMP_INT | LM87_ALARM_TEMP_EXT1);
 161         is_failure = temp_crit || elec_fault;
 162
 163         if (alarms)
 164                 netif_err(efx, hw, efx->net_dev,
 165                           "LM87 detected a hardware %s (status %02x:%02x)"
 166                           "%s%s%s%s\n",
 167                           is_failure ? "failure" : "problem",
 168                           alarms & 0xff, alarms >> 8,
 169                           (alarms & LM87_ALARM_TEMP_INT) ?
 170                           "; board is overheating" : "",
 171                           (alarms & LM87_ALARM_TEMP_EXT1) ?
 172                           "; controller is overheating" : "",
 173                           temp_crit ? "; reached critical temperature" : "",
 174                           elec_fault ? "; electrical fault" : "");
 175
 176         return is_failure ? -ERANGE : 0;
 177 }
 178
 179 #else /* !CONFIG_SENSORS_LM87 */
 180
 181 static inline int
 182 efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info,
 183               const u8 *reg_values)
 184 {
 185         return 0;
 186 }
 187 static inline void efx_fini_lm87(struct efx_nic *efx)
 188 {
 189 }
 190 static inline int efx_check_lm87(struct efx_nic *efx, unsigned mask)
 191 {
 192         return 0;
 193 }
 194
 195 #endif /* CONFIG_SENSORS_LM87 */
 196
 197 /*****************************************************************************
 198  * Support for the SFE4001 NIC.
 199  *
 200  * The SFE4001 does not power-up fully at reset due to its high power
 201  * consumption.  We control its power via a PCA9539 I/O expander.
 202  * It also has a MAX6647 temperature monitor which we expose to
 203  * the lm90 driver.
 204  *
 205  * This also provides minimal support for reflashing the PHY, which is
 206  * initiated by resetting it with the FLASH_CFG_1 pin pulled down.
 207  * On SFE4001 rev A2 and later this is connected to the 3V3X output of
 208  * the IO-expander.
 209  * We represent reflash mode as PHY_MODE_SPECIAL and make it mutually
 210  * exclusive with the network device being open.
 211  */
 212
 213 /**************************************************************************
 214  * Support for I2C IO Expander device on SFE4001
 215  */
 216 #define PCA9539 0x74
 217
 218 #define P0_IN 0x00
 219 #define P0_OUT 0x02
 220 #define P0_INVERT 0x04
 221 #define P0_CONFIG 0x06
 222
 223 #define P0_EN_1V0X_LBN 0
 224 #define P0_EN_1V0X_WIDTH 1
 225 #define P0_EN_1V2_LBN 1
 226 #define P0_EN_1V2_WIDTH 1
 227 #define P0_EN_2V5_LBN 2
 228 #define P0_EN_2V5_WIDTH 1
 229 #define P0_EN_3V3X_LBN 3
 230 #define P0_EN_3V3X_WIDTH 1
 231 #define P0_EN_5V_LBN 4
 232 #define P0_EN_5V_WIDTH 1
 233 #define P0_SHORTEN_JTAG_LBN 5
 234 #define P0_SHORTEN_JTAG_WIDTH 1
 235 #define P0_X_TRST_LBN 6
 236 #define P0_X_TRST_WIDTH 1
 237 #define P0_DSP_RESET_LBN 7
 238 #define P0_DSP_RESET_WIDTH 1
 239
 240 #define P1_IN 0x01
 241 #define P1_OUT 0x03
 242 #define P1_INVERT 0x05
 243 #define P1_CONFIG 0x07
 244
 245 #define P1_AFE_PWD_LBN 0
 246 #define P1_AFE_PWD_WIDTH 1
 247 #define P1_DSP_PWD25_LBN 1
 248 #define P1_DSP_PWD25_WIDTH 1
 249 #define P1_RESERVED_LBN 2
 250 #define P1_RESERVED_WIDTH 2
 251 #define P1_SPARE_LBN 4
 252 #define P1_SPARE_WIDTH 4
 253
 254 /* Temperature Sensor */
 255 #define MAX664X_REG_RSL         0x02
 256 #define MAX664X_REG_WLHO        0x0B
 257
 258 static void sfe4001_poweroff(struct efx_nic *efx)
 259 {
 260         struct i2c_client *ioexp_client = falcon_board(efx)->ioexp_client;
 261         struct i2c_client *hwmon_client = falcon_board(efx)->hwmon_client;
 262
 263         /* Turn off all power rails and disable outputs */
 264         i2c_smbus_write_byte_data(ioexp_client, P0_OUT, 0xff);
 265         i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG, 0xff);
 266         i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0xff);
 267
 268         /* Clear any over-temperature alert */
 269         i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL);
 270 }
 271
 272 static int sfe4001_poweron(struct efx_nic *efx)
 273 {
 274         struct i2c_client *ioexp_client = falcon_board(efx)->ioexp_client;
 275         struct i2c_client *hwmon_client = falcon_board(efx)->hwmon_client;
 276         unsigned int i, j;
 277         int rc;
 278         u8 out;
 279
 280         /* Clear any previous over-temperature alert */
 281         rc = i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL);
 282         if (rc < 0)
 283                 return rc;
 284
 285         /* Enable port 0 and port 1 outputs on IO expander */
 286         rc = i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0x00);
 287         if (rc)
 288                 return rc;
 289         rc = i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG,
 290                                        0xff & ~(1 << P1_SPARE_LBN));
 291         if (rc)
 292                 goto fail_on;
 293
 294         /* If PHY power is on, turn it all off and wait 1 second to
 295          * ensure a full reset.
 296          */
 297         rc = i2c_smbus_read_byte_data(ioexp_client, P0_OUT);
 298         if (rc < 0)
 299                 goto fail_on;
 300         out = 0xff & ~((0 << P0_EN_1V2_LBN) | (0 << P0_EN_2V5_LBN) |
 301                        (0 << P0_EN_3V3X_LBN) | (0 << P0_EN_5V_LBN) |
 302                        (0 << P0_EN_1V0X_LBN));
 303         if (rc != out) {
 304                 netif_info(efx, hw, efx->net_dev, "power-cycling PHY\n");
 305                 rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
 306                 if (rc)
 307                         goto fail_on;
 308                 schedule_timeout_uninterruptible(HZ);
 309         }
 310
 311         for (i = 0; i < 20; ++i) {
 312                 /* Turn on 1.2V, 2.5V, 3.3V and 5V power rails */
 313                 out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) |
 314                                (1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) |
 315                                (1 << P0_X_TRST_LBN));
 316                 if (efx->phy_mode & PHY_MODE_SPECIAL)
 317                         out |= 1 << P0_EN_3V3X_LBN;
 318
 319                 rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
 320                 if (rc)
 321                         goto fail_on;
 322                 msleep(10);
 323
 324                 /* Turn on 1V power rail */
 325                 out &= ~(1 << P0_EN_1V0X_LBN);
 326                 rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
 327                 if (rc)
 328                         goto fail_on;
 329
 330                 netif_info(efx, hw, efx->net_dev,
 331                            "waiting for DSP boot (attempt %d)...\n", i);
 332
 333                 /* In flash config mode, DSP does not turn on AFE, so
 334                  * just wait 1 second.
 335                  */
 336                 if (efx->phy_mode & PHY_MODE_SPECIAL) {
 337                         schedule_timeout_uninterruptible(HZ);
 338                         return 0;
 339                 }
 340
 341                 for (j = 0; j < 10; ++j) {
 342                         msleep(100);
 343
 344                         /* Check DSP has asserted AFE power line */
 345                         rc = i2c_smbus_read_byte_data(ioexp_client, P1_IN);
 346                         if (rc < 0)
 347                                 goto fail_on;
 348                         if (rc & (1 << P1_AFE_PWD_LBN))
 349                                 return 0;
 350                 }
 351         }
 352
 353         netif_info(efx, hw, efx->net_dev, "timed out waiting for DSP boot\n");
 354         rc = -ETIMEDOUT;
 355 fail_on:
 356         sfe4001_poweroff(efx);
 357         return rc;
 358 }
 359
 360 static ssize_t show_phy_flash_cfg(struct device *dev,
 361                                   struct device_attribute *attr, char *buf)
 362 {
 363         struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev));
 364         return sprintf(buf, "%d\n", !!(efx->phy_mode & PHY_MODE_SPECIAL));
 365 }
 366
 367 static ssize_t set_phy_flash_cfg(struct device *dev,
 368                                  struct device_attribute *attr,
 369                                  const char *buf, size_t count)
 370 {
 371         struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev));
 372         enum efx_phy_mode old_mode, new_mode;
 373         int err;
 374
 375         rtnl_lock();
 376         old_mode = efx->phy_mode;
 377         if (count == 0 || *buf == '0')
 378                 new_mode = old_mode & ~PHY_MODE_SPECIAL;
 379         else
 380                 new_mode = PHY_MODE_SPECIAL;
 381         if (!((old_mode ^ new_mode) & PHY_MODE_SPECIAL)) {
 382                 err = 0;
 383         } else if (efx->state != STATE_RUNNING || netif_running(efx->net_dev)) {
 384                 err = -EBUSY;
 385         } else {
 386                 /* Reset the PHY, reconfigure the MAC and enable/disable
 387                  * MAC stats accordingly. */
 388                 efx->phy_mode = new_mode;
 389                 if (new_mode & PHY_MODE_SPECIAL)
 390                         falcon_stop_nic_stats(efx);
 391                 err = sfe4001_poweron(efx);
 392                 if (!err)
 393                         err = efx_reconfigure_port(efx);
 394                 if (!(new_mode & PHY_MODE_SPECIAL))
 395                         falcon_start_nic_stats(efx);
 396         }
 397         rtnl_unlock();
 398
 399         return err ? err : count;
 400 }
 401
 402 static DEVICE_ATTR(phy_flash_cfg, 0644, show_phy_flash_cfg, set_phy_flash_cfg);
 403
 404 static void sfe4001_fini(struct efx_nic *efx)
 405 {
 406         struct falcon_board *board = falcon_board(efx);
 407
 408         netif_info(efx, drv, efx->net_dev, "%s\n", __func__);
 409
 410         device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
 411         sfe4001_poweroff(efx);
 412         i2c_unregister_device(board->ioexp_client);
 413         i2c_unregister_device(board->hwmon_client);
 414 }
 415
 416 static int sfe4001_check_hw(struct efx_nic *efx)
 417 {
 418         struct falcon_nic_data *nic_data = efx->nic_data;
 419         s32 status;
 420
 421         /* If XAUI link is up then do not monitor */
 422         if (EFX_WORKAROUND_7884(efx) && !nic_data->xmac_poll_required)
 423                 return 0;
 424
 425         /* Check the powered status of the PHY. Lack of power implies that
 426          * the MAX6647 has shut down power to it, probably due to a temp.
 427          * alarm. Reading the power status rather than the MAX6647 status
 428          * directly because the later is read-to-clear and would thus
 429          * start to power up the PHY again when polled, causing us to blip
 430          * the power undesirably.
 431          * We know we can read from the IO expander because we did
 432          * it during power-on. Assume failure now is bad news. */
 433         status = i2c_smbus_read_byte_data(falcon_board(efx)->ioexp_client, P1_IN);
 434         if (status >= 0 &&
 435             (status & ((1 << P1_AFE_PWD_LBN) | (1 << P1_DSP_PWD25_LBN))) != 0)
 436                 return 0;
 437
 438         /* Use board power control, not PHY power control */
 439         sfe4001_poweroff(efx);
 440         efx->phy_mode = PHY_MODE_OFF;
 441
 442         return (status < 0) ? -EIO : -ERANGE;
 443 }
 444
 445 static struct i2c_board_info sfe4001_hwmon_info = {
 446         I2C_BOARD_INFO("max6647", 0x4e),
 447 };
 448
 449 /* This board uses an I2C expander to provider power to the PHY, which needs to
 450  * be turned on before the PHY can be used.
 451  * Context: Process context, rtnl lock held
 452  */
 453 static int sfe4001_init(struct efx_nic *efx)
 454 {
 455         struct falcon_board *board = falcon_board(efx);
 456         int rc;
 457
 458 #if defined(CONFIG_SENSORS_LM90) || defined(CONFIG_SENSORS_LM90_MODULE)
 459         board->hwmon_client =
 460                 i2c_new_device(&board->i2c_adap, &sfe4001_hwmon_info);
 461 #else
 462         board->hwmon_client =
 463                 i2c_new_dummy(&board->i2c_adap, sfe4001_hwmon_info.addr);
 464 #endif
 465         if (!board->hwmon_client)
 466                 return -EIO;
 467
 468         /* Raise board/PHY high limit from 85 to 90 degrees Celsius */
 469         rc = i2c_smbus_write_byte_data(board->hwmon_client,
 470                                        MAX664X_REG_WLHO, 90);
 471         if (rc)
 472                 goto fail_hwmon;
 473
 474         board->ioexp_client = i2c_new_dummy(&board->i2c_adap, PCA9539);
 475         if (!board->ioexp_client) {
 476                 rc = -EIO;
 477                 goto fail_hwmon;
 478         }
 479
 480         if (efx->phy_mode & PHY_MODE_SPECIAL) {
 481                 /* PHY won't generate a 156.25 MHz clock and MAC stats fetch
 482                  * will fail. */
 483                 falcon_stop_nic_stats(efx);
 484         }
 485         rc = sfe4001_poweron(efx);
 486         if (rc)
 487                 goto fail_ioexp;
 488
 489         rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
 490         if (rc)
 491                 goto fail_on;
 492
 493         netif_info(efx, hw, efx->net_dev, "PHY is powered on\n");
 494         return 0;
 495
 496 fail_on:
 497         sfe4001_poweroff(efx);
 498 fail_ioexp:
 499         i2c_unregister_device(board->ioexp_client);
 500 fail_hwmon:
 501         i2c_unregister_device(board->hwmon_client);
 502         return rc;
 503 }
 504
 505 /*****************************************************************************
 506  * Support for the SFE4002
 507  *
 508  */
 509 static u8 sfe4002_lm87_channel = 0x03; /* use AIN not FAN inputs */
 510
 511 static const u8 sfe4002_lm87_regs[] = {
 512         LM87_IN_LIMITS(0, 0x7c, 0x99),          /* 2.5V:  1.8V +/- 10% */
 513         LM87_IN_LIMITS(1, 0x4c, 0x5e),          /* Vccp1: 1.2V +/- 10% */
 514         LM87_IN_LIMITS(2, 0xac, 0xd4),          /* 3.3V:  3.3V +/- 10% */
 515         LM87_IN_LIMITS(3, 0xac, 0xd4),          /* 5V:    5.0V +/- 10% */
 516         LM87_IN_LIMITS(4, 0xac, 0xe0),          /* 12V:   10.8-14V */
 517         LM87_IN_LIMITS(5, 0x3f, 0x4f),          /* Vccp2: 1.0V +/- 10% */
 518         LM87_AIN_LIMITS(0, 0x98, 0xbb),         /* AIN1:  1.66V +/- 10% */
 519         LM87_AIN_LIMITS(1, 0x8a, 0xa9),         /* AIN2:  1.5V +/- 10% */
 520         LM87_TEMP_INT_LIMITS(0, 80 + FALCON_BOARD_TEMP_BIAS),
 521         LM87_TEMP_EXT1_LIMITS(0, FALCON_JUNC_TEMP_MAX),
 522         0
 523 };
 524
 525 static struct i2c_board_info sfe4002_hwmon_info = {
 526         I2C_BOARD_INFO("lm87", 0x2e),
 527         .platform_data  = &sfe4002_lm87_channel,
 528 };
 529
 530 /****************************************************************************/
 531 /* LED allocations. Note that on rev A0 boards the schematic and the reality
 532  * differ: red and green are swapped. Below is the fixed (A1) layout (there
 533  * are only 3 A0 boards in existence, so no real reason to make this
 534  * conditional).
 535  */
 536 #define SFE4002_FAULT_LED (2)   /* Red */
 537 #define SFE4002_RX_LED    (0)   /* Green */
 538 #define SFE4002_TX_LED    (1)   /* Amber */
 539
 540 static void sfe4002_init_phy(struct efx_nic *efx)
 541 {
 542         /* Set the TX and RX LEDs to reflect status and activity, and the
 543          * fault LED off */
 544         falcon_qt202x_set_led(efx, SFE4002_TX_LED,
 545                               QUAKE_LED_TXLINK | QUAKE_LED_LINK_ACTSTAT);
 546         falcon_qt202x_set_led(efx, SFE4002_RX_LED,
 547                               QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACTSTAT);
 548         falcon_qt202x_set_led(efx, SFE4002_FAULT_LED, QUAKE_LED_OFF);
 549 }
 550
 551 static void sfe4002_set_id_led(struct efx_nic *efx, enum efx_led_mode mode)
 552 {
 553         falcon_qt202x_set_led(
 554                 efx, SFE4002_FAULT_LED,
 555                 (mode == EFX_LED_ON) ? QUAKE_LED_ON : QUAKE_LED_OFF);
 556 }
 557
 558 static int sfe4002_check_hw(struct efx_nic *efx)
 559 {
 560         struct falcon_board *board = falcon_board(efx);
 561
 562         /* A0 board rev. 4002s report a temperature fault the whole time
 563          * (bad sensor) so we mask it out. */
 564         unsigned alarm_mask =
 565                 (board->major == 0 && board->minor == 0) ?
 566                 ~LM87_ALARM_TEMP_EXT1 : ~0;
 567
 568         return efx_check_lm87(efx, alarm_mask);
 569 }
 570
 571 static int sfe4002_init(struct efx_nic *efx)
 572 {
 573         return efx_init_lm87(efx, &sfe4002_hwmon_info, sfe4002_lm87_regs);
 574 }
 575
 576 /*****************************************************************************
 577  * Support for the SFN4112F
 578  *
 579  */
 580 static u8 sfn4112f_lm87_channel = 0x03; /* use AIN not FAN inputs */
 581
 582 static const u8 sfn4112f_lm87_regs[] = {
 583         LM87_IN_LIMITS(0, 0x7c, 0x99),          /* 2.5V:  1.8V +/- 10% */
 584         LM87_IN_LIMITS(1, 0x4c, 0x5e),          /* Vccp1: 1.2V +/- 10% */
 585         LM87_IN_LIMITS(2, 0xac, 0xd4),          /* 3.3V:  3.3V +/- 10% */
 586         LM87_IN_LIMITS(4, 0xac, 0xe0),          /* 12V:   10.8-14V */
 587         LM87_IN_LIMITS(5, 0x3f, 0x4f),          /* Vccp2: 1.0V +/- 10% */
 588         LM87_AIN_LIMITS(1, 0x8a, 0xa9),         /* AIN2:  1.5V +/- 10% */
 589         LM87_TEMP_INT_LIMITS(0, 60 + FALCON_BOARD_TEMP_BIAS),
 590         LM87_TEMP_EXT1_LIMITS(0, FALCON_JUNC_TEMP_MAX),
 591         0
 592 };
 593
 594 static struct i2c_board_info sfn4112f_hwmon_info = {
 595         I2C_BOARD_INFO("lm87", 0x2e),
 596         .platform_data  = &sfn4112f_lm87_channel,
 597 };
 598
 599 #define SFN4112F_ACT_LED        0
 600 #define SFN4112F_LINK_LED       1
 601
 602 static void sfn4112f_init_phy(struct efx_nic *efx)
 603 {
 604         falcon_qt202x_set_led(efx, SFN4112F_ACT_LED,
 605                               QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACT);
 606         falcon_qt202x_set_led(efx, SFN4112F_LINK_LED,
 607                               QUAKE_LED_RXLINK | QUAKE_LED_LINK_STAT);
 608 }
 609
 610 static void sfn4112f_set_id_led(struct efx_nic *efx, enum efx_led_mode mode)
 611 {
 612         int reg;
 613
 614         switch (mode) {
 615         case EFX_LED_OFF:
 616                 reg = QUAKE_LED_OFF;
 617                 break;
 618         case EFX_LED_ON:
 619                 reg = QUAKE_LED_ON;
 620                 break;
 621         default:
 622                 reg = QUAKE_LED_RXLINK | QUAKE_LED_LINK_STAT;
 623                 break;
 624         }
 625
 626         falcon_qt202x_set_led(efx, SFN4112F_LINK_LED, reg);
 627 }
 628
 629 static int sfn4112f_check_hw(struct efx_nic *efx)
 630 {
 631         /* Mask out unused sensors */
 632         return efx_check_lm87(efx, ~0x48);
 633 }
 634
 635 static int sfn4112f_init(struct efx_nic *efx)
 636 {
 637         return efx_init_lm87(efx, &sfn4112f_hwmon_info, sfn4112f_lm87_regs);
 638 }
 639
 640 /*****************************************************************************
 641  * Support for the SFE4003
 642  *
 643  */
 644 static u8 sfe4003_lm87_channel = 0x03; /* use AIN not FAN inputs */
 645
 646 static const u8 sfe4003_lm87_regs[] = {
 647         LM87_IN_LIMITS(0, 0x67, 0x7f),          /* 2.5V:  1.5V +/- 10% */
 648         LM87_IN_LIMITS(1, 0x4c, 0x5e),          /* Vccp1: 1.2V +/- 10% */
 649         LM87_IN_LIMITS(2, 0xac, 0xd4),          /* 3.3V:  3.3V +/- 10% */
 650         LM87_IN_LIMITS(4, 0xac, 0xe0),          /* 12V:   10.8-14V */
 651         LM87_IN_LIMITS(5, 0x3f, 0x4f),          /* Vccp2: 1.0V +/- 10% */
 652         LM87_TEMP_INT_LIMITS(0, 70 + FALCON_BOARD_TEMP_BIAS),
 653         0
 654 };
 655
 656 static struct i2c_board_info sfe4003_hwmon_info = {
 657         I2C_BOARD_INFO("lm87", 0x2e),
 658         .platform_data  = &sfe4003_lm87_channel,
 659 };
 660
 661 /* Board-specific LED info. */
 662 #define SFE4003_RED_LED_GPIO    11
 663 #define SFE4003_LED_ON          1
 664 #define SFE4003_LED_OFF         0
 665
 666 static void sfe4003_set_id_led(struct efx_nic *efx, enum efx_led_mode mode)
 667 {
 668         struct falcon_board *board = falcon_board(efx);
 669
 670         /* The LEDs were not wired to GPIOs before A3 */
 671         if (board->minor < 3 && board->major == 0)
 672                 return;
 673
 674         falcon_txc_set_gpio_val(
 675                 efx, SFE4003_RED_LED_GPIO,
 676                 (mode == EFX_LED_ON) ? SFE4003_LED_ON : SFE4003_LED_OFF);
 677 }
 678
 679 static void sfe4003_init_phy(struct efx_nic *efx)
 680 {
 681         struct falcon_board *board = falcon_board(efx);
 682
 683         /* The LEDs were not wired to GPIOs before A3 */
 684         if (board->minor < 3 && board->major == 0)
 685                 return;
 686
 687         falcon_txc_set_gpio_dir(efx, SFE4003_RED_LED_GPIO, TXC_GPIO_DIR_OUTPUT);
 688         falcon_txc_set_gpio_val(efx, SFE4003_RED_LED_GPIO, SFE4003_LED_OFF);
 689 }
 690
 691 static int sfe4003_check_hw(struct efx_nic *efx)
 692 {
 693         struct falcon_board *board = falcon_board(efx);
 694
 695         /* A0/A1/A2 board rev. 4003s  report a temperature fault the whole time
 696          * (bad sensor) so we mask it out. */
 697         unsigned alarm_mask =
 698                 (board->major == 0 && board->minor <= 2) ?
 699                 ~LM87_ALARM_TEMP_EXT1 : ~0;
 700
 701         return efx_check_lm87(efx, alarm_mask);
 702 }
 703
 704 static int sfe4003_init(struct efx_nic *efx)
 705 {
 706         return efx_init_lm87(efx, &sfe4003_hwmon_info, sfe4003_lm87_regs);
 707 }
 708
 709 static const struct falcon_board_type board_types[] = {
 710         {
 711                 .id             = FALCON_BOARD_SFE4001,
 712                 .ref_model      = "SFE4001",
 713                 .gen_type       = "10GBASE-T adapter",
 714                 .init           = sfe4001_init,
 715                 .init_phy       = efx_port_dummy_op_void,
 716                 .fini           = sfe4001_fini,
 717                 .set_id_led     = tenxpress_set_id_led,
 718                 .monitor        = sfe4001_check_hw,
 719         },
 720         {
 721                 .id             = FALCON_BOARD_SFE4002,
 722                 .ref_model      = "SFE4002",
 723                 .gen_type       = "XFP adapter",
 724                 .init           = sfe4002_init,
 725                 .init_phy       = sfe4002_init_phy,
 726                 .fini           = efx_fini_lm87,
 727                 .set_id_led     = sfe4002_set_id_led,
 728                 .monitor        = sfe4002_check_hw,
 729         },
 730         {
 731                 .id             = FALCON_BOARD_SFE4003,
 732                 .ref_model      = "SFE4003",
 733                 .gen_type       = "10GBASE-CX4 adapter",
 734                 .init           = sfe4003_init,
 735                 .init_phy       = sfe4003_init_phy,
 736                 .fini           = efx_fini_lm87,
 737                 .set_id_led     = sfe4003_set_id_led,
 738                 .monitor        = sfe4003_check_hw,
 739         },
 740         {
 741                 .id             = FALCON_BOARD_SFN4112F,
 742                 .ref_model      = "SFN4112F",
 743                 .gen_type       = "SFP+ adapter",
 744                 .init           = sfn4112f_init,
 745                 .init_phy       = sfn4112f_init_phy,
 746                 .fini           = efx_fini_lm87,
 747                 .set_id_led     = sfn4112f_set_id_led,
 748                 .monitor        = sfn4112f_check_hw,
 749         },
 750 };
 751
 752 int falcon_probe_board(struct efx_nic *efx, u16 revision_info)
 753 {
 754         struct falcon_board *board = falcon_board(efx);
 755         u8 type_id = FALCON_BOARD_TYPE(revision_info);
 756         int i;
 757
 758         board->major = FALCON_BOARD_MAJOR(revision_info);
 759         board->minor = FALCON_BOARD_MINOR(revision_info);
 760
 761         for (i = 0; i < ARRAY_SIZE(board_types); i++)
 762                 if (board_types[i].id == type_id)
 763                         board->type = &board_types[i];
 764
 765         if (board->type) {
 766                 netif_info(efx, probe, efx->net_dev, "board is %s rev %c%d\n",
 767                          (efx->pci_dev->subsystem_vendor == EFX_VENDID_SFC)
 768                          ? board->type->ref_model : board->type->gen_type,
 769                          'A' + board->major, board->minor);
 770                 return 0;
 771         } else {
 772                 netif_err(efx, probe, efx->net_dev, "unknown board type %d\n",
 773                           type_id);
 774                 return -ENODEV;
 775         }
 776 }