drivers/usb/serial/ftdi_sio.h

   1 /*
   2  * Definitions for the FTDI USB Single Port Serial Converter -
   3  * known as FTDI_SIO (Serial Input/Output application of the chipset)
   4  *
   5  * The example I have is known as the USC-1000 which is available from
   6  * http://www.dse.co.nz - cat no XH4214 It looks similar to this:
   7  * http://www.dansdata.com/usbser.htm but I can't be sure There are other
   8  * USC-1000s which don't look like my device though so beware!
   9  *
  10  * The device is based on the FTDI FT8U100AX chip. It has a DB25 on one side,
  11  * USB on the other.
  12  *
  13  * Thanx to FTDI (http://www.ftdi.co.uk) for so kindly providing details
  14  * of the protocol required to talk to the device and ongoing assistence
  15  * during development.
  16  *
  17  * Bill Ryder - bryder@sgi.com formerly of Silicon Graphics, Inc.- wrote the
  18  * FTDI_SIO implementation.
  19  *
  20  * Philipp Gühring - pg@futureware.at - added the Device ID of the USB relais
  21  * from Rudolf Gugler
  22  *
  23  */
  24
  25 #define FTDI_VID        0x0403  /* Vendor Id */
  26 #define FTDI_SIO_PID    0x8372  /* Product Id SIO application of 8U100AX  */
  27 #define FTDI_8U232AM_PID 0x6001 /* Similar device to SIO above */
  28 #define FTDI_8U232AM_ALT_PID 0x6006 /* FTDI's alternate PID for above */
  29 #define FTDI_8U2232C_PID 0x6010 /* Dual channel device */
  30 #define FTDI_RELAIS_PID 0xFA10  /* Relais device from Rudolf Gugler */
  31 #define FTDI_NF_RIC_VID 0x0DCD  /* Vendor Id */
  32 #define FTDI_NF_RIC_PID 0x0001  /* Product Id */
  33
  34 /* www.irtrans.de device */
  35 #define FTDI_IRTRANS_PID 0xFC60 /* Product Id */
  36
  37 /* www.crystalfontz.com devices - thanx for providing free devices for evaluation ! */
  38 /* they use the ftdi chipset for the USB interface and the vendor id is the same */
  39 #define FTDI_XF_632_PID 0xFC08  /* 632: 16x2 Character Display */
  40 #define FTDI_XF_634_PID 0xFC09  /* 634: 20x4 Character Display */
  41 #define FTDI_XF_547_PID 0xFC0A  /* 547: Two line Display */
  42 #define FTDI_XF_633_PID 0xFC0B  /* 633: 16x2 Character Display with Keys */
  43 #define FTDI_XF_631_PID 0xFC0C  /* 631: 20x2 Character Display */
  44 #define FTDI_XF_635_PID 0xFC0D  /* 635: 20x4 Character Display */
  45 #define FTDI_XF_640_PID 0xFC0E  /* 640: Two line Display */
  46 #define FTDI_XF_642_PID 0xFC0F  /* 642: Two line Display */
  47
  48 /* Video Networks Limited / Homechoice in the UK use an ftdi-based device for their 1Mb */
  49 /* broadband internet service.  The following PID is exhibited by the usb device supplied */
  50 /* (the VID is the standard ftdi vid (FTDI_VID) */
  51 #define FTDI_VNHCPCUSB_D_PID 0xfe38 /* Product Id */
  52
  53 /*
  54  * The following are the values for the Matrix Orbital LCD displays,
  55  * which are the FT232BM ( similar to the 8U232AM )
  56  */
  57 #define FTDI_MTXORB_0_PID      0xFA00  /* Matrix Orbital Product Id */
  58 #define FTDI_MTXORB_1_PID      0xFA01  /* Matrix Orbital Product Id */
  59 #define FTDI_MTXORB_2_PID      0xFA02  /* Matrix Orbital Product Id */
  60 #define FTDI_MTXORB_3_PID      0xFA03  /* Matrix Orbital Product Id */
  61 #define FTDI_MTXORB_4_PID      0xFA04  /* Matrix Orbital Product Id */
  62 #define FTDI_MTXORB_5_PID      0xFA05  /* Matrix Orbital Product Id */
  63 #define FTDI_MTXORB_6_PID      0xFA06  /* Matrix Orbital Product Id */
  64
  65 /* Interbiometrics USB I/O Board */
  66 /* Developed for Interbiometrics by Rudolf Gugler */
  67 #define INTERBIOMETRICS_VID              0x1209
  68 #define INTERBIOMETRICS_IOBOARD_PID      0x1002
  69 #define INTERBIOMETRICS_MINI_IOBOARD_PID 0x1006
  70
  71 /*
  72  * The following are the values for the Perle Systems
  73  * UltraPort USB serial converters
  74  */
  75 #define FTDI_PERLE_ULTRAPORT_PID 0xF0C0 /* Perle UltraPort Product Id */
  76
  77 /*
  78  * The following are the values for the Sealevel SeaLINK+ adapters.
  79  * (Original list sent by Tuan Hoang.  Ian Abbott renamed the macros and
  80  * removed some PIDs that don't seem to match any existing products.)
  81  */
  82 #define SEALEVEL_VID            0x0c52  /* Sealevel Vendor ID */
  83 #define SEALEVEL_2101_PID       0x2101  /* SeaLINK+232 (2101/2105) */
  84 #define SEALEVEL_2102_PID       0x2102  /* SeaLINK+485 (2102) */
  85 #define SEALEVEL_2103_PID       0x2103  /* SeaLINK+232I (2103) */
  86 #define SEALEVEL_2104_PID       0x2104  /* SeaLINK+485I (2104) */
  87 #define SEALEVEL_2201_1_PID     0x2211  /* SeaPORT+2/232 (2201) Port 1 */
  88 #define SEALEVEL_2201_2_PID     0x2221  /* SeaPORT+2/232 (2201) Port 2 */
  89 #define SEALEVEL_2202_1_PID     0x2212  /* SeaPORT+2/485 (2202) Port 1 */
  90 #define SEALEVEL_2202_2_PID     0x2222  /* SeaPORT+2/485 (2202) Port 2 */
  91 #define SEALEVEL_2203_1_PID     0x2213  /* SeaPORT+2 (2203) Port 1 */
  92 #define SEALEVEL_2203_2_PID     0x2223  /* SeaPORT+2 (2203) Port 2 */
  93 #define SEALEVEL_2401_1_PID     0x2411  /* SeaPORT+4/232 (2401) Port 1 */
  94 #define SEALEVEL_2401_2_PID     0x2421  /* SeaPORT+4/232 (2401) Port 2 */
  95 #define SEALEVEL_2401_3_PID     0x2431  /* SeaPORT+4/232 (2401) Port 3 */
  96 #define SEALEVEL_2401_4_PID     0x2441  /* SeaPORT+4/232 (2401) Port 4 */
  97 #define SEALEVEL_2402_1_PID     0x2412  /* SeaPORT+4/485 (2402) Port 1 */
  98 #define SEALEVEL_2402_2_PID     0x2422  /* SeaPORT+4/485 (2402) Port 2 */
  99 #define SEALEVEL_2402_3_PID     0x2432  /* SeaPORT+4/485 (2402) Port 3 */
 100 #define SEALEVEL_2402_4_PID     0x2442  /* SeaPORT+4/485 (2402) Port 4 */
 101 #define SEALEVEL_2403_1_PID     0x2413  /* SeaPORT+4 (2403) Port 1 */
 102 #define SEALEVEL_2403_2_PID     0x2423  /* SeaPORT+4 (2403) Port 2 */
 103 #define SEALEVEL_2403_3_PID     0x2433  /* SeaPORT+4 (2403) Port 3 */
 104 #define SEALEVEL_2403_4_PID     0x2443  /* SeaPORT+4 (2403) Port 4 */
 105 #define SEALEVEL_2801_1_PID     0X2811  /* SeaLINK+8/232 (2801) Port 1 */
 106 #define SEALEVEL_2801_2_PID     0X2821  /* SeaLINK+8/232 (2801) Port 2 */
 107 #define SEALEVEL_2801_3_PID     0X2831  /* SeaLINK+8/232 (2801) Port 3 */
 108 #define SEALEVEL_2801_4_PID     0X2841  /* SeaLINK+8/232 (2801) Port 4 */
 109 #define SEALEVEL_2801_5_PID     0X2851  /* SeaLINK+8/232 (2801) Port 5 */
 110 #define SEALEVEL_2801_6_PID     0X2861  /* SeaLINK+8/232 (2801) Port 6 */
 111 #define SEALEVEL_2801_7_PID     0X2871  /* SeaLINK+8/232 (2801) Port 7 */
 112 #define SEALEVEL_2801_8_PID     0X2881  /* SeaLINK+8/232 (2801) Port 8 */
 113 #define SEALEVEL_2802_1_PID     0X2812  /* SeaLINK+8/485 (2802) Port 1 */
 114 #define SEALEVEL_2802_2_PID     0X2822  /* SeaLINK+8/485 (2802) Port 2 */
 115 #define SEALEVEL_2802_3_PID     0X2832  /* SeaLINK+8/485 (2802) Port 3 */
 116 #define SEALEVEL_2802_4_PID     0X2842  /* SeaLINK+8/485 (2802) Port 4 */
 117 #define SEALEVEL_2802_5_PID     0X2852  /* SeaLINK+8/485 (2802) Port 5 */
 118 #define SEALEVEL_2802_6_PID     0X2862  /* SeaLINK+8/485 (2802) Port 6 */
 119 #define SEALEVEL_2802_7_PID     0X2872  /* SeaLINK+8/485 (2802) Port 7 */
 120 #define SEALEVEL_2802_8_PID     0X2882  /* SeaLINK+8/485 (2802) Port 8 */
 121 #define SEALEVEL_2803_1_PID     0X2813  /* SeaLINK+8 (2803) Port 1 */
 122 #define SEALEVEL_2803_2_PID     0X2823  /* SeaLINK+8 (2803) Port 2 */
 123 #define SEALEVEL_2803_3_PID     0X2833  /* SeaLINK+8 (2803) Port 3 */
 124 #define SEALEVEL_2803_4_PID     0X2843  /* SeaLINK+8 (2803) Port 4 */
 125 #define SEALEVEL_2803_5_PID     0X2853  /* SeaLINK+8 (2803) Port 5 */
 126 #define SEALEVEL_2803_6_PID     0X2863  /* SeaLINK+8 (2803) Port 6 */
 127 #define SEALEVEL_2803_7_PID     0X2873  /* SeaLINK+8 (2803) Port 7 */
 128 #define SEALEVEL_2803_8_PID     0X2883  /* SeaLINK+8 (2803) Port 8 */
 129
 130 /*
 131  * The following are the values for two KOBIL chipcard terminals.
 132  */
 133 #define KOBIL_VID               0x0d46  /* KOBIL Vendor ID */
 134 #define KOBIL_CONV_B1_PID       0x2020  /* KOBIL Konverter for B1 */
 135 #define KOBIL_CONV_KAAN_PID     0x2021  /* KOBIL_Konverter for KAAN */
 136
 137 /*
 138  * DSS-20 Sync Station for Sony Ericsson P800
 139  */
 140
 141 #define FTDI_DSS20_PID          0xFC82
 142
 143 /*
 144  * Home Electronics (www.home-electro.com) USB gadgets
 145  */
 146 #define FTDI_HE_TIRA1_PID       0xFA78  /* Tira-1 IR transceiver */
 147
 148 /* USB-UIRT - An infrared receiver and transmitter using the 8U232AM chip */
 149 /* http://home.earthlink.net/~jrhees/USBUIRT/index.htm */
 150 #define FTDI_USB_UIRT_PID       0xF850  /* Product Id */
 151
 152 /*
 153  * ELV USB devices submitted by Christian Abt of ELV (www.elv.de).
 154  * All of these devices use FTDI's vendor ID (0x0403).
 155  *
 156  * The previously included PID for the UO 100 module was incorrect.
 157  * In fact, that PID was for ELV's UR 100 USB-RS232 converter (0xFB58).
 158  *
 159  * Armin Laeuger originally sent the PID for the UM 100 module.
 160  */
 161 #define FTDI_ELV_UR100_PID      0xFB58  /* USB-RS232-Umsetzer (UR 100) */
 162 #define FTDI_ELV_UM100_PID      0xFB5A  /* USB-Modul UM 100 */
 163 #define FTDI_ELV_UO100_PID      0xFB5B  /* USB-Modul UO 100 */
 164 #define FTDI_ELV_ALC8500_PID    0xF06E  /* ALC 8500 Expert */
 165 /* Additional ELV PIDs that default to using the FTDI D2XX drivers on
 166  * MS Windows, rather than the FTDI Virtual Com Port drivers.
 167  * Maybe these will be easier to use with the libftdi/libusb user-space
 168  * drivers, or possibly the Comedi drivers in some cases. */
 169 #define FTDI_ELV_CLI7000_PID    0xFB59  /* Computer-Light-Interface (CLI 7000) */
 170 #define FTDI_ELV_PPS7330_PID    0xFB5C  /* Processor-Power-Supply (PPS 7330) */
 171 #define FTDI_ELV_TFM100_PID     0xFB5D  /* Temperartur-Feuchte Messgeraet (TFM 100) */
 172 #define FTDI_ELV_UDF77_PID      0xFB5E  /* USB DCF Funkurh (UDF 77) */
 173 #define FTDI_ELV_UIO88_PID      0xFB5F  /* USB-I/O Interface (UIO 88) */
 174 #define FTDI_ELV_UAD8_PID       0xF068  /* USB-AD-Wandler (UAD 8) */
 175 #define FTDI_ELV_UDA7_PID       0xF069  /* USB-DA-Wandler (UDA 7) */
 176 #define FTDI_ELV_USI2_PID       0xF06A  /* USB-Schrittmotoren-Interface (USI 2) */
 177 #define FTDI_ELV_T1100_PID      0xF06B  /* Thermometer (T 1100) */
 178 #define FTDI_ELV_PCD200_PID     0xF06C  /* PC-Datenlogger (PCD 200) */
 179 #define FTDI_ELV_ULA200_PID     0xF06D  /* USB-LCD-Ansteuerung (ULA 200) */
 180 #define FTDI_ELV_FHZ1000PC_PID  0xF06F  /* FHZ 1000 PC */
 181 #define FTDI_ELV_CSI8_PID       0xE0F0  /* Computer-Schalt-Interface (CSI 8) */
 182 #define FTDI_ELV_EM1000DL_PID   0xE0F1  /* PC-Datenlogger fuer Energiemonitor (EM 1000 DL) */
 183 #define FTDI_ELV_PCK100_PID     0xE0F2  /* PC-Kabeltester (PCK 100) */
 184 #define FTDI_ELV_RFP500_PID     0xE0F3  /* HF-Leistungsmesser (RFP 500) */
 185 #define FTDI_ELV_FS20SIG_PID    0xE0F4  /* Signalgeber (FS 20 SIG) */
 186 #define FTDI_ELV_WS300PC_PID    0xE0F6  /* PC-Wetterstation (WS 300 PC) */
 187 #define FTDI_ELV_FHZ1300PC_PID  0xE0E8  /* FHZ 1300 PC */
 188 #define FTDI_ELV_WS500_PID      0xE0E9  /* PC-Wetterstation (WS 500) */
 189
 190 /*
 191  * Definitions for ID TECH (www.idt-net.com) devices
 192  */
 193 #define IDTECH_VID              0x0ACD  /* ID TECH Vendor ID */
 194 #define IDTECH_IDT1221U_PID     0x0300  /* IDT1221U USB to RS-232 adapter */
 195
 196 /*
 197  * Definitions for Omnidirectional Control Technology, Inc. devices
 198  */
 199 #define OCT_VID                 0x0B39  /* OCT vendor ID */
 200 /* Note: OCT US101 is also rebadged as Dick Smith Electronics (NZ) XH6381 */
 201 /* Also rebadged as Dick Smith Electronics (Aus) XH6451 */
 202 /* Also rebadged as SIIG Inc. model US2308 hardware version 1 */
 203 #define OCT_US101_PID           0x0421  /* OCT US101 USB to RS-232 */
 204
 205 /* an infrared receiver for user access control with IR tags */
 206 #define FTDI_PIEGROUP_PID       0xF208  /* Product Id */
 207
 208 /*
 209  * Definitions for Artemis astronomical USB based cameras
 210  * Check it at http://www.artemisccd.co.uk/
 211  */
 212 #define FTDI_ARTEMIS_PID        0xDF28  /* All Artemis Cameras */
 213
 214 /*
 215  * Definitions for ATIK Instruments astronomical USB based cameras
 216  * Check it at http://www.atik-instruments.com/
 217  */
 218 #define FTDI_ATIK_ATK16_PID     0xDF30  /* ATIK ATK-16 Camera */
 219 #define FTDI_ATIK_ATK16HR_PID   0xDF31  /* ATIK ATK-16HR Camera */
 220
 221 /*
 222  * Protego product ids
 223  */
 224 #define PROTEGO_SPECIAL_1       0xFC70  /* special/unknown device */
 225 #define PROTEGO_R2X0            0xFC71  /* R200-USB TRNG unit (R210, R220, and R230) */
 226 #define PROTEGO_SPECIAL_3       0xFC72  /* special/unknown device */
 227 #define PROTEGO_SPECIAL_4       0xFC73  /* special/unknown device */
 228
 229 /*
 230  * Gude Analog- und Digitalsysteme GmbH
 231  */
 232 #define FTDI_GUDEADS_E808_PID    0xE808
 233 #define FTDI_GUDEADS_E809_PID    0xE809
 234 #define FTDI_GUDEADS_E80A_PID    0xE80A
 235 #define FTDI_GUDEADS_E80B_PID    0xE80B
 236 #define FTDI_GUDEADS_E80C_PID    0xE80C
 237 #define FTDI_GUDEADS_E80D_PID    0xE80D
 238 #define FTDI_GUDEADS_E80E_PID    0xE80E
 239 #define FTDI_GUDEADS_E80F_PID    0xE80F
 240 #define FTDI_GUDEADS_E888_PID    0xE888  /* Expert ISDN Control USB */
 241 #define FTDI_GUDEADS_E889_PID    0xE889  /* USB RS-232 OptoBridge */
 242 #define FTDI_GUDEADS_E88A_PID    0xE88A
 243 #define FTDI_GUDEADS_E88B_PID    0xE88B
 244 #define FTDI_GUDEADS_E88C_PID    0xE88C
 245 #define FTDI_GUDEADS_E88D_PID    0xE88D
 246 #define FTDI_GUDEADS_E88E_PID    0xE88E
 247 #define FTDI_GUDEADS_E88F_PID    0xE88F
 248
 249 /*
 250  * Linx Technologies product ids
 251  */
 252 #define LINX_SDMUSBQSS_PID      0xF448  /* Linx SDM-USB-QS-S */
 253 #define LINX_MASTERDEVEL2_PID   0xF449   /* Linx Master Development 2.0 */
 254 #define LINX_FUTURE_0_PID   0xF44A   /* Linx future device */
 255 #define LINX_FUTURE_1_PID   0xF44B   /* Linx future device */
 256 #define LINX_FUTURE_2_PID   0xF44C   /* Linx future device */
 257
 258 /* CCS Inc. ICDU/ICDU40 product ID - the FT232BM is used in an in-circuit-debugger */
 259 /* unit for PIC16's/PIC18's */
 260 #define FTDI_CCSICDU20_0_PID    0xF9D0
 261 #define FTDI_CCSICDU40_1_PID    0xF9D1
 262
 263 /* Inside Accesso contactless reader (http://www.insidefr.com) */
 264 #define INSIDE_ACCESSO          0xFAD0
 265
 266 /*
 267  * Intrepid Control Systems (http://www.intrepidcs.com/) ValueCAN and NeoVI
 268  */
 269 #define INTREPID_VID            0x093C
 270 #define INTREPID_VALUECAN_PID   0x0601
 271 #define INTREPID_NEOVI_PID      0x0701
 272
 273 /*
 274  * Falcom Wireless Communications GmbH
 275  */
 276 #define FALCOM_VID              0x0F94  /* Vendor Id */
 277 #define FALCOM_TWIST_PID        0x0001  /* Falcom Twist USB GPRS modem */
 278 #define FALCOM_SAMBA_PID        0x0005  /* Falcom Samba USB GPRS modem */
 279
 280 /*
 281  * SUUNTO product ids
 282  */
 283 #define FTDI_SUUNTO_SPORTS_PID  0xF680  /* Suunto Sports instrument */
 284
 285 /*
 286  * Definitions for B&B Electronics products.
 287  */
 288 #define BANDB_VID               0x0856  /* B&B Electronics Vendor ID */
 289 #define BANDB_USOTL4_PID        0xAC01  /* USOTL4 Isolated RS-485 Converter */
 290 #define BANDB_USTL4_PID         0xAC02  /* USTL4 RS-485 Converter */
 291 #define BANDB_USO9ML2_PID       0xAC03  /* USO9ML2 Isolated RS-232 Converter */
 292
 293 /*
 294  * RM Michaelides CANview USB (http://www.rmcan.com)
 295  * CAN fieldbus interface adapter, added by port GmbH www.port.de)
 296  * Ian Abbott changed the macro names for consistency.
 297  */
 298 #define FTDI_RM_CANVIEW_PID     0xfd60  /* Product Id */
 299
 300 /*
 301  * EVER Eco Pro UPS (http://www.ever.com.pl/)
 302  */
 303
 304 #define EVER_ECO_PRO_CDS        0xe520  /* RS-232 converter */
 305
 306 /*
 307  * 4N-GALAXY.DE PIDs for CAN-USB, USB-RS232, USB-RS422, USB-RS485,
 308  * USB-TTY activ, USB-TTY passiv.  Some PIDs are used by several devices
 309  * and I'm not entirely sure which are used by which.
 310  */
 311 #define FTDI_4N_GALAXY_DE_0_PID 0x8372
 312 #define FTDI_4N_GALAXY_DE_1_PID 0xF3C0
 313 #define FTDI_4N_GALAXY_DE_2_PID 0xF3C1
 314
 315 /*
 316  * Mobility Electronics products.
 317  */
 318 #define MOBILITY_VID                    0x1342
 319 #define MOBILITY_USB_SERIAL_PID         0x0202  /* EasiDock USB 200 serial */
 320
 321 /*
 322  * microHAM product IDs (http://www.microham.com).
 323  * Submitted by Justin Burket (KL1RL) <zorton@jtan.com>.
 324  */
 325 #define FTDI_MHAM_Y6_PID 0xEEEA         /* USB-Y6 interface */
 326 #define FTDI_MHAM_Y8_PID 0xEEEB         /* USB-Y8 interface */
 327
 328 /*
 329  * Active Robots product ids.
 330  */
 331 #define FTDI_ACTIVE_ROBOTS_PID  0xE548  /* USB comms board */
 332
 333 /*
 334  * Xsens Technologies BV products (http://www.xsens.com).
 335  */
 336 #define XSENS_CONVERTER_0_PID   0xD388
 337 #define XSENS_CONVERTER_1_PID   0xD389
 338 #define XSENS_CONVERTER_2_PID   0xD38A
 339 #define XSENS_CONVERTER_3_PID   0xD38B
 340 #define XSENS_CONVERTER_4_PID   0xD38C
 341 #define XSENS_CONVERTER_5_PID   0xD38D
 342 #define XSENS_CONVERTER_6_PID   0xD38E
 343 #define XSENS_CONVERTER_7_PID   0xD38F
 344
 345 /*
 346  * Teratronik product ids.
 347  * Submitted by O. Wölfelschneider.
 348  */
 349 #define FTDI_TERATRONIK_VCP_PID  0xEC88 /* Teratronik device (preferring VCP driver on windows) */
 350 #define FTDI_TERATRONIK_D2XX_PID 0xEC89 /* Teratronik device (preferring D2XX driver on windows) */
 351
 352 /*
 353  * Evolution Robotics products (http://www.evolution.com/).
 354  * Submitted by Shawn M. Lavelle.
 355  */
 356 #define EVOLUTION_VID           0xDEEE  /* Vendor ID */
 357 #define EVOLUTION_ER1_PID       0x0300  /* ER1 Control Module */
 358
 359 /* Pyramid Computer GmbH */
 360 #define FTDI_PYRAMID_PID        0xE6C8  /* Pyramid Appliance Display */
 361
 362 /*
 363  * Posiflex inc retail equipment (http://www.posiflex.com.tw)
 364  */
 365 #define POSIFLEX_VID            0x0d3a  /* Vendor ID */
 366 #define POSIFLEX_PP7000_PID     0x0300  /* PP-7000II thermal printer */
 367
 368 /* Commands */
 369 #define FTDI_SIO_RESET          0 /* Reset the port */
 370 #define FTDI_SIO_MODEM_CTRL     1 /* Set the modem control register */
 371 #define FTDI_SIO_SET_FLOW_CTRL  2 /* Set flow control register */
 372 #define FTDI_SIO_SET_BAUD_RATE  3 /* Set baud rate */
 373 #define FTDI_SIO_SET_DATA       4 /* Set the data characteristics of the port */
 374 #define FTDI_SIO_GET_MODEM_STATUS       5 /* Retrieve current value of modern status register */
 375 #define FTDI_SIO_SET_EVENT_CHAR 6 /* Set the event character */
 376 #define FTDI_SIO_SET_ERROR_CHAR 7 /* Set the error character */
 377 #define FTDI_SIO_SET_LATENCY_TIMER      9 /* Set the latency timer */
 378 #define FTDI_SIO_GET_LATENCY_TIMER      10 /* Get the latency timer */
 379
 380
 381 /*
 382  *   BmRequestType:  1100 0000b
 383  *   bRequest:       FTDI_E2_READ
 384  *   wValue:         0
 385  *   wIndex:         Address of word to read
 386  *   wLength:        2
 387  *   Data:           Will return a word of data from E2Address
 388  *
 389  */
 390
 391 /* Port Identifier Table */
 392 #define PIT_DEFAULT             0 /* SIOA */
 393 #define PIT_SIOA                1 /* SIOA */
 394 /* The device this driver is tested with one has only one port */
 395 #define PIT_SIOB                2 /* SIOB */
 396 #define PIT_PARALLEL            3 /* Parallel */
 397
 398 /* FTDI_SIO_RESET */
 399 #define FTDI_SIO_RESET_REQUEST FTDI_SIO_RESET
 400 #define FTDI_SIO_RESET_REQUEST_TYPE 0x40
 401 #define FTDI_SIO_RESET_SIO 0
 402 #define FTDI_SIO_RESET_PURGE_RX 1
 403 #define FTDI_SIO_RESET_PURGE_TX 2
 404
 405 /*
 406  * BmRequestType:  0100 0000B
 407  * bRequest:       FTDI_SIO_RESET
 408  * wValue:         Control Value
 409  *                   0 = Reset SIO
 410  *                   1 = Purge RX buffer
 411  *                   2 = Purge TX buffer
 412  * wIndex:         Port
 413  * wLength:        0
 414  * Data:           None
 415  *
 416  * The Reset SIO command has this effect:
 417  *
 418  *    Sets flow control set to 'none'
 419  *    Event char = $0D
 420  *    Event trigger = disabled
 421  *    Purge RX buffer
 422  *    Purge TX buffer
 423  *    Clear DTR
 424  *    Clear RTS
 425  *    baud and data format not reset
 426  *
 427  * The Purge RX and TX buffer commands affect nothing except the buffers
 428  *
 429    */
 430
 431 /* FTDI_SIO_SET_BAUDRATE */
 432 #define FTDI_SIO_SET_BAUDRATE_REQUEST_TYPE 0x40
 433 #define FTDI_SIO_SET_BAUDRATE_REQUEST 3
 434
 435 /*
 436  * BmRequestType:  0100 0000B
 437  * bRequest:       FTDI_SIO_SET_BAUDRATE
 438  * wValue:         BaudDivisor value - see below
 439  * wIndex:         Port
 440  * wLength:        0
 441  * Data:           None
 442  * The BaudDivisor values are calculated as follows:
 443  * - BaseClock is either 12000000 or 48000000 depending on the device. FIXME: I wish
 444  *   I knew how to detect old chips to select proper base clock!
 445  * - BaudDivisor is a fixed point number encoded in a funny way.
 446  *   (--WRONG WAY OF THINKING--)
 447  *   BaudDivisor is a fixed point number encoded with following bit weighs:
 448  *   (-2)(-1)(13..0). It is a radical with a denominator of 4, so values
 449  *   end with 0.0 (00...), 0.25 (10...), 0.5 (01...), and 0.75 (11...).
 450  *   (--THE REALITY--)
 451  *   The both-bits-set has quite different meaning from 0.75 - the chip designers
 452  *   have decided it to mean 0.125 instead of 0.75.
 453  *   This info looked up in FTDI application note "FT8U232 DEVICES \ Data Rates
 454  *   and Flow Control Consideration for USB to RS232".
 455  * - BaudDivisor = (BaseClock / 16) / BaudRate, where the (=) operation should
 456  *   automagically re-encode the resulting value to take fractions into consideration.
 457  * As all values are integers, some bit twiddling is in order:
 458  *   BaudDivisor = (BaseClock / 16 / BaudRate) |
 459  *   (((BaseClock / 2 / BaudRate) & 4) ? 0x4000    // 0.5
 460  *    : ((BaseClock / 2 / BaudRate) & 2) ? 0x8000  // 0.25
 461  *    : ((BaseClock / 2 / BaudRate) & 1) ? 0xc000  // 0.125
 462  *    : 0)
 463  *
 464  * For the FT232BM, a 17th divisor bit was introduced to encode the multiples
 465  * of 0.125 missing from the FT8U232AM.  Bits 16 to 14 are coded as follows
 466  * (the first four codes are the same as for the FT8U232AM, where bit 16 is
 467  * always 0):
 468  *   000 - add .000 to divisor
 469  *   001 - add .500 to divisor
 470  *   010 - add .250 to divisor
 471  *   011 - add .125 to divisor
 472  *   100 - add .375 to divisor
 473  *   101 - add .625 to divisor
 474  *   110 - add .750 to divisor
 475  *   111 - add .875 to divisor
 476  * Bits 15 to 0 of the 17-bit divisor are placed in the urb value.  Bit 16 is
 477  * placed in bit 0 of the urb index.
 478  *
 479  * Note that there are a couple of special cases to support the highest baud
 480  * rates.  If the calculated divisor value is 1, this needs to be replaced with
 481  * 0.  Additionally for the FT232BM, if the calculated divisor value is 0x4001
 482  * (1.5), this needs to be replaced with 0x0001 (1) (but this divisor value is
 483  * not supported by the FT8U232AM).
 484  */
 485
 486 typedef enum {
 487         SIO = 1,
 488         FT8U232AM = 2,
 489         FT232BM = 3,
 490         FT2232C = 4,
 491 } ftdi_chip_type_t;
 492
 493 typedef enum {
 494  ftdi_sio_b300 = 0,
 495  ftdi_sio_b600 = 1,
 496  ftdi_sio_b1200 = 2,
 497  ftdi_sio_b2400 = 3,
 498  ftdi_sio_b4800 = 4,
 499  ftdi_sio_b9600 = 5,
 500  ftdi_sio_b19200 = 6,
 501  ftdi_sio_b38400 = 7,
 502  ftdi_sio_b57600 = 8,
 503  ftdi_sio_b115200 = 9
 504 } FTDI_SIO_baudrate_t ;
 505
 506 /*
 507  * The ftdi_8U232AM_xxMHz_byyy constants have been removed. The encoded divisor values
 508  * are calculated internally.
 509  */
 510
 511 #define FTDI_SIO_SET_DATA_REQUEST FTDI_SIO_SET_DATA
 512 #define FTDI_SIO_SET_DATA_REQUEST_TYPE 0x40
 513 #define FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8 )
 514 #define FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8 )
 515 #define FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8 )
 516 #define FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8 )
 517 #define FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8 )
 518 #define FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11 )
 519 #define FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11 )
 520 #define FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11 )
 521 #define FTDI_SIO_SET_BREAK (0x1 << 14)
 522 /* FTDI_SIO_SET_DATA */
 523
 524 /*
 525  * BmRequestType:  0100 0000B
 526  * bRequest:       FTDI_SIO_SET_DATA
 527  * wValue:         Data characteristics (see below)
 528  * wIndex:         Port
 529  * wLength:        0
 530  * Data:           No
 531  *
 532  * Data characteristics
 533  *
 534  *   B0..7   Number of data bits
 535  *   B8..10  Parity
 536  *           0 = None
 537  *           1 = Odd
 538  *           2 = Even
 539  *           3 = Mark
 540  *           4 = Space
 541  *   B11..13 Stop Bits
 542  *           0 = 1
 543  *           1 = 1.5
 544  *           2 = 2
 545  *   B14
 546  *           1 = TX ON (break)
 547  *           0 = TX OFF (normal state)
 548  *   B15 Reserved
 549  *
 550  */
 551
 552
 553
 554 /* FTDI_SIO_MODEM_CTRL */
 555 #define FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE 0x40
 556 #define FTDI_SIO_SET_MODEM_CTRL_REQUEST FTDI_SIO_MODEM_CTRL
 557
 558 /*
 559  * BmRequestType:   0100 0000B
 560  * bRequest:        FTDI_SIO_MODEM_CTRL
 561  * wValue:          ControlValue (see below)
 562  * wIndex:          Port
 563  * wLength:         0
 564  * Data:            None
 565  *
 566  * NOTE: If the device is in RTS/CTS flow control, the RTS set by this
 567  * command will be IGNORED without an error being returned
 568  * Also - you can not set DTR and RTS with one control message
 569  */
 570
 571 #define FTDI_SIO_SET_DTR_MASK 0x1
 572 #define FTDI_SIO_SET_DTR_HIGH ( 1 | ( FTDI_SIO_SET_DTR_MASK  << 8))
 573 #define FTDI_SIO_SET_DTR_LOW  ( 0 | ( FTDI_SIO_SET_DTR_MASK  << 8))
 574 #define FTDI_SIO_SET_RTS_MASK 0x2
 575 #define FTDI_SIO_SET_RTS_HIGH ( 2 | ( FTDI_SIO_SET_RTS_MASK << 8 ))
 576 #define FTDI_SIO_SET_RTS_LOW ( 0 | ( FTDI_SIO_SET_RTS_MASK << 8 ))
 577
 578 /*
 579  * ControlValue
 580  * B0    DTR state
 581  *          0 = reset
 582  *          1 = set
 583  * B1    RTS state
 584  *          0 = reset
 585  *          1 = set
 586  * B2..7 Reserved
 587  * B8    DTR state enable
 588  *          0 = ignore
 589  *          1 = use DTR state
 590  * B9    RTS state enable
 591  *          0 = ignore
 592  *          1 = use RTS state
 593  * B10..15 Reserved
 594  */
 595
 596 /* FTDI_SIO_SET_FLOW_CTRL */
 597 #define FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE 0x40
 598 #define FTDI_SIO_SET_FLOW_CTRL_REQUEST FTDI_SIO_SET_FLOW_CTRL
 599 #define FTDI_SIO_DISABLE_FLOW_CTRL 0x0
 600 #define FTDI_SIO_RTS_CTS_HS (0x1 << 8)
 601 #define FTDI_SIO_DTR_DSR_HS (0x2 << 8)
 602 #define FTDI_SIO_XON_XOFF_HS (0x4 << 8)
 603 /*
 604  *   BmRequestType:  0100 0000b
 605  *   bRequest:       FTDI_SIO_SET_FLOW_CTRL
 606  *   wValue:         Xoff/Xon
 607  *   wIndex:         Protocol/Port - hIndex is protocl / lIndex is port
 608  *   wLength:        0
 609  *   Data:           None
 610  *
 611  * hIndex protocol is:
 612  *   B0 Output handshaking using RTS/CTS
 613  *       0 = disabled
 614  *       1 = enabled
 615  *   B1 Output handshaking using DTR/DSR
 616  *       0 = disabled
 617  *       1 = enabled
 618  *   B2 Xon/Xoff handshaking
 619  *       0 = disabled
 620  *       1 = enabled
 621  *
 622  * A value of zero in the hIndex field disables handshaking
 623  *
 624  * If Xon/Xoff handshaking is specified, the hValue field should contain the XOFF character
 625  * and the lValue field contains the XON character.
 626  */
 627
 628 /*
 629  * FTDI_SIO_GET_LATENCY_TIMER
 630  *
 631  * Set the timeout interval. The FTDI collects data from the slave
 632  * device, transmitting it to the host when either A) 62 bytes are
 633  * received, or B) the timeout interval has elapsed and the buffer
 634  * contains at least 1 byte.  Setting this value to a small number
 635  * can dramatically improve performance for applications which send
 636  * small packets, since the default value is 16ms.
 637  */
 638 #define  FTDI_SIO_GET_LATENCY_TIMER_REQUEST FTDI_SIO_GET_LATENCY_TIMER
 639 #define  FTDI_SIO_GET_LATENCY_TIMER_REQUEST_TYPE 0xC0
 640
 641 /*
 642  *  BmRequestType:   1100 0000b
 643  *  bRequest:        FTDI_SIO_GET_LATENCY_TIMER
 644  *  wValue:          0
 645  *  wIndex:          Port
 646  *  wLength:         0
 647  *  Data:            latency (on return)
 648  */
 649
 650 /*
 651  * FTDI_SIO_SET_LATENCY_TIMER
 652  *
 653  * Set the timeout interval. The FTDI collects data from the slave
 654  * device, transmitting it to the host when either A) 62 bytes are
 655  * received, or B) the timeout interval has elapsed and the buffer
 656  * contains at least 1 byte.  Setting this value to a small number
 657  * can dramatically improve performance for applications which send
 658  * small packets, since the default value is 16ms.
 659  */
 660 #define  FTDI_SIO_SET_LATENCY_TIMER_REQUEST FTDI_SIO_SET_LATENCY_TIMER
 661 #define  FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE 0x40
 662
 663 /*
 664  *  BmRequestType:   0100 0000b
 665  *  bRequest:        FTDI_SIO_SET_LATENCY_TIMER
 666  *  wValue:          Latency (milliseconds)
 667  *  wIndex:          Port
 668  *  wLength:         0
 669  *  Data:            None
 670  *
 671  * wValue:
 672  *   B0..7   Latency timer
 673  *   B8..15  0
 674  *
 675  */
 676
 677 /*
 678  * FTDI_SIO_SET_EVENT_CHAR
 679  *
 680  * Set the special event character for the specified communications port.
 681  * If the device sees this character it will immediately return the
 682  * data read so far - rather than wait 40ms or until 62 bytes are read
 683  * which is what normally happens.
 684  */
 685
 686
 687 #define  FTDI_SIO_SET_EVENT_CHAR_REQUEST FTDI_SIO_SET_EVENT_CHAR
 688 #define  FTDI_SIO_SET_EVENT_CHAR_REQUEST_TYPE 0x40
 689
 690
 691 /*
 692  *  BmRequestType:   0100 0000b
 693  *  bRequest:        FTDI_SIO_SET_EVENT_CHAR
 694  *  wValue:          EventChar
 695  *  wIndex:          Port
 696  *  wLength:         0
 697  *  Data:            None
 698  *
 699  * wValue:
 700  *   B0..7   Event Character
 701  *   B8      Event Character Processing
 702  *             0 = disabled
 703  *             1 = enabled
 704  *   B9..15  Reserved
 705  *
 706  */
 707
 708 /* FTDI_SIO_SET_ERROR_CHAR */
 709
 710 /* Set the parity error replacement character for the specified communications port */
 711
 712 /*
 713  *  BmRequestType:  0100 0000b
 714  *  bRequest:       FTDI_SIO_SET_EVENT_CHAR
 715  *  wValue:         Error Char
 716  *  wIndex:         Port
 717  *  wLength:        0
 718  *  Data:           None
 719  *
 720  *Error Char
 721  *  B0..7  Error Character
 722  *  B8     Error Character Processing
 723  *           0 = disabled
 724  *           1 = enabled
 725  *  B9..15 Reserved
 726  *
 727  */
 728
 729 /* FTDI_SIO_GET_MODEM_STATUS */
 730 /* Retrieve the current value of the modem status register */
 731
 732 #define FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE 0xc0
 733 #define FTDI_SIO_GET_MODEM_STATUS_REQUEST FTDI_SIO_GET_MODEM_STATUS
 734 #define FTDI_SIO_CTS_MASK 0x10
 735 #define FTDI_SIO_DSR_MASK 0x20
 736 #define FTDI_SIO_RI_MASK  0x40
 737 #define FTDI_SIO_RLSD_MASK 0x80
 738 /*
 739  *   BmRequestType:   1100 0000b
 740  *   bRequest:        FTDI_SIO_GET_MODEM_STATUS
 741  *   wValue:          zero
 742  *   wIndex:          Port
 743  *   wLength:         1
 744  *   Data:            Status
 745  *
 746  * One byte of data is returned
 747  * B0..3 0
 748  * B4    CTS
 749  *         0 = inactive
 750  *         1 = active
 751  * B5    DSR
 752  *         0 = inactive
 753  *         1 = active
 754  * B6    Ring Indicator (RI)
 755  *         0 = inactive
 756  *         1 = active
 757  * B7    Receive Line Signal Detect (RLSD)
 758  *         0 = inactive
 759  *         1 = active
 760  */
 761
 762
 763
 764 /* Descriptors returned by the device
 765  *
 766  *  Device Descriptor
 767  *
 768  * Offset       Field           Size    Value   Description
 769  * 0    bLength         1       0x12    Size of descriptor in bytes
 770  * 1    bDescriptorType 1       0x01    DEVICE Descriptor Type
 771  * 2    bcdUSB          2       0x0110  USB Spec Release Number
 772  * 4    bDeviceClass    1       0x00    Class Code
 773  * 5    bDeviceSubClass 1       0x00    SubClass Code
 774  * 6    bDeviceProtocol 1       0x00    Protocol Code
 775  * 7    bMaxPacketSize0 1       0x08    Maximum packet size for endpoint 0
 776  * 8    idVendor        2       0x0403  Vendor ID
 777  * 10   idProduct       2       0x8372  Product ID (FTDI_SIO_PID)
 778  * 12   bcdDevice       2       0x0001  Device release number
 779  * 14   iManufacturer   1       0x01    Index of man. string desc
 780  * 15   iProduct        1       0x02    Index of prod string desc
 781  * 16   iSerialNumber   1       0x02    Index of serial nmr string desc
 782  * 17   bNumConfigurations 1    0x01    Number of possible configurations
 783  *
 784  * Configuration Descriptor
 785  *
 786  * Offset       Field                   Size    Value
 787  * 0    bLength                 1       0x09    Size of descriptor in bytes
 788  * 1    bDescriptorType         1       0x02    CONFIGURATION Descriptor Type
 789  * 2    wTotalLength            2       0x0020  Total length of data
 790  * 4    bNumInterfaces          1       0x01    Number of interfaces supported
 791  * 5    bConfigurationValue     1       0x01    Argument for SetCOnfiguration() req
 792  * 6    iConfiguration          1       0x02    Index of config string descriptor
 793  * 7    bmAttributes            1       0x20    Config characteristics Remote Wakeup
 794  * 8    MaxPower                1       0x1E    Max power consumption
 795  *
 796  * Interface Descriptor
 797  *
 798  * Offset       Field                   Size    Value
 799  * 0    bLength                 1       0x09    Size of descriptor in bytes
 800  * 1    bDescriptorType         1       0x04    INTERFACE Descriptor Type
 801  * 2    bInterfaceNumber        1       0x00    Number of interface
 802  * 3    bAlternateSetting       1       0x00    Value used to select alternate
 803  * 4    bNumEndpoints           1       0x02    Number of endpoints
 804  * 5    bInterfaceClass         1       0xFF    Class Code
 805  * 6    bInterfaceSubClass      1       0xFF    Subclass Code
 806  * 7    bInterfaceProtocol      1       0xFF    Protocol Code
 807  * 8    iInterface              1       0x02    Index of interface string description
 808  *
 809  * IN Endpoint Descriptor
 810  *
 811  * Offset       Field                   Size    Value
 812  * 0    bLength                 1       0x07    Size of descriptor in bytes
 813  * 1    bDescriptorType         1       0x05    ENDPOINT descriptor type
 814  * 2    bEndpointAddress        1       0x82    Address of endpoint
 815  * 3    bmAttributes            1       0x02    Endpoint attributes - Bulk
 816  * 4    bNumEndpoints           2       0x0040  maximum packet size
 817  * 5    bInterval               1       0x00    Interval for polling endpoint
 818  *
 819  * OUT Endpoint Descriptor
 820  *
 821  * Offset       Field                   Size    Value
 822  * 0    bLength                 1       0x07    Size of descriptor in bytes
 823  * 1    bDescriptorType         1       0x05    ENDPOINT descriptor type
 824  * 2    bEndpointAddress        1       0x02    Address of endpoint
 825  * 3    bmAttributes            1       0x02    Endpoint attributes - Bulk
 826  * 4    bNumEndpoints           2       0x0040  maximum packet size
 827  * 5    bInterval               1       0x00    Interval for polling endpoint
 828  *
 829  * DATA FORMAT
 830  *
 831  * IN Endpoint
 832  *
 833  * The device reserves the first two bytes of data on this endpoint to contain the current
 834  * values of the modem and line status registers. In the absence of data, the device
 835  * generates a message consisting of these two status bytes every 40 ms
 836  *
 837  * Byte 0: Modem Status
 838  *
 839  * Offset       Description
 840  * B0   Reserved - must be 1
 841  * B1   Reserved - must be 0
 842  * B2   Reserved - must be 0
 843  * B3   Reserved - must be 0
 844  * B4   Clear to Send (CTS)
 845  * B5   Data Set Ready (DSR)
 846  * B6   Ring Indicator (RI)
 847  * B7   Receive Line Signal Detect (RLSD)
 848  *
 849  * Byte 1: Line Status
 850  *
 851  * Offset       Description
 852  * B0   Data Ready (DR)
 853  * B1   Overrun Error (OE)
 854  * B2   Parity Error (PE)
 855  * B3   Framing Error (FE)
 856  * B4   Break Interrupt (BI)
 857  * B5   Transmitter Holding Register (THRE)
 858  * B6   Transmitter Empty (TEMT)
 859  * B7   Error in RCVR FIFO
 860  *
 861  */
 862 #define FTDI_RS0_CTS    (1 << 4)
 863 #define FTDI_RS0_DSR    (1 << 5)
 864 #define FTDI_RS0_RI     (1 << 6)
 865 #define FTDI_RS0_RLSD   (1 << 7)
 866
 867 #define FTDI_RS_DR  1
 868 #define FTDI_RS_OE (1<<1)
 869 #define FTDI_RS_PE (1<<2)
 870 #define FTDI_RS_FE (1<<3)
 871 #define FTDI_RS_BI (1<<4)
 872 #define FTDI_RS_THRE (1<<5)
 873 #define FTDI_RS_TEMT (1<<6)
 874 #define FTDI_RS_FIFO  (1<<7)
 875
 876 /*
 877  * OUT Endpoint
 878  *
 879  * This device reserves the first bytes of data on this endpoint contain the length
 880  * and port identifier of the message. For the FTDI USB Serial converter the port
 881  * identifier is always 1.
 882  *
 883  * Byte 0: Line Status
 884  *
 885  * Offset       Description
 886  * B0   Reserved - must be 1
 887  * B1   Reserved - must be 0
 888  * B2..7        Length of message - (not including Byte 0)
 889  *
 890  */
 891