drivers/ide/ide-cd.h

   1 /*
   2  *  linux/drivers/ide/ide_cd.h
   3  *
   4  *  Copyright (C) 1996-98  Erik Andersen
   5  *  Copyright (C) 1998-2000 Jens Axboe
   6  */
   7 #ifndef _IDE_CD_H
   8 #define _IDE_CD_H
   9
  10 #include <linux/cdrom.h>
  11 #include <asm/byteorder.h>
  12
  13 /* Turn this on to have the driver print out the meanings of the
  14    ATAPI error codes.  This will use up additional kernel-space
  15    memory, though. */
  16
  17 #ifndef VERBOSE_IDE_CD_ERRORS
  18 #define VERBOSE_IDE_CD_ERRORS 1
  19 #endif
  20
  21
  22 /* Turning this on will remove code to work around various nonstandard
  23    ATAPI implementations.  If you know your drive follows the standard,
  24    this will give you a slightly smaller kernel. */
  25
  26 #ifndef STANDARD_ATAPI
  27 #define STANDARD_ATAPI 0
  28 #endif
  29
  30
  31 /* Turning this on will disable the door-locking functionality.
  32    This is apparently needed for supermount. */
  33
  34 #ifndef NO_DOOR_LOCKING
  35 #define NO_DOOR_LOCKING 0
  36 #endif
  37
  38 /*
  39  * typical timeout for packet command
  40  */
  41 #define ATAPI_WAIT_PC           (60 * HZ)
  42 #define ATAPI_WAIT_WRITE_BUSY   (10 * HZ)
  43
  44 /************************************************************************/
  45
  46 #define SECTOR_BITS             9
  47 #ifndef SECTOR_SIZE
  48 #define SECTOR_SIZE             (1 << SECTOR_BITS)
  49 #endif
  50 #define SECTORS_PER_FRAME       (CD_FRAMESIZE >> SECTOR_BITS)
  51 #define SECTOR_BUFFER_SIZE      (CD_FRAMESIZE * 32)
  52 #define SECTORS_BUFFER          (SECTOR_BUFFER_SIZE >> SECTOR_BITS)
  53 #define SECTORS_MAX             (131072 >> SECTOR_BITS)
  54
  55 #define BLOCKS_PER_FRAME        (CD_FRAMESIZE / BLOCK_SIZE)
  56
  57 /* special command codes for strategy routine. */
  58 #define PACKET_COMMAND        4315
  59 #define REQUEST_SENSE_COMMAND 4316
  60 #define RESET_DRIVE_COMMAND   4317
  61
  62
  63 /* Configuration flags.  These describe the capabilities of the drive.
  64    They generally do not change after initialization, unless we learn
  65    more about the drive from stuff failing. */
  66 struct ide_cd_config_flags {
  67         __u8 drq_interrupt      : 1; /* Device sends an interrupt when ready
  68                                         for a packet command. */
  69         __u8 no_doorlock        : 1; /* Drive cannot lock the door. */
  70         __u8 no_eject           : 1; /* Drive cannot eject the disc. */
  71         __u8 nec260             : 1; /* Drive is a pre-1.2 NEC 260 drive. */
  72         __u8 playmsf_as_bcd     : 1; /* PLAYMSF command takes BCD args. */
  73         __u8 tocaddr_as_bcd     : 1; /* TOC addresses are in BCD. */
  74         __u8 toctracks_as_bcd   : 1; /* TOC track numbers are in BCD. */
  75         __u8 subchan_as_bcd     : 1; /* Subchannel info is in BCD. */
  76         __u8 is_changer         : 1; /* Drive is a changer. */
  77         __u8 cd_r               : 1; /* Drive can write to CD-R media . */
  78         __u8 cd_rw              : 1; /* Drive can write to CD-R/W media . */
  79         __u8 dvd                : 1; /* Drive is a DVD-ROM */
  80         __u8 dvd_r              : 1; /* Drive can write DVD-R */
  81         __u8 dvd_ram            : 1; /* Drive can write DVD-RAM */
  82         __u8 ram                : 1; /* generic WRITE (dvd-ram/mrw) */
  83         __u8 test_write         : 1; /* Drive can fake writes */
  84         __u8 supp_disc_present  : 1; /* Changer can report exact contents
  85                                         of slots. */
  86         __u8 limit_nframes      : 1; /* Drive does not provide data in
  87                                         multiples of SECTOR_SIZE when more
  88                                         than one interrupt is needed. */
  89         __u8 seeking            : 1; /* Seeking in progress */
  90         __u8 audio_play         : 1; /* can do audio related commands */
  91         __u8 close_tray         : 1; /* can close the tray */
  92         __u8 writing            : 1; /* pseudo write in progress */
  93         __u8 mo_drive           : 1; /* drive is an MO device */
  94         __u8 no_speed_select    : 1; /* SET_CD_SPEED command is unsupported. */
  95         __u8 reserved           : 1;
  96         byte max_speed;              /* Max speed of the drive */
  97 };
  98 #define CDROM_CONFIG_FLAGS(drive) (&(((struct cdrom_info *)(drive->driver_data))->config_flags))
  99
 100
 101 /* State flags.  These give information about the current state of the
 102    drive, and will change during normal operation. */
 103 struct ide_cd_state_flags {
 104         __u8 media_changed : 1; /* Driver has noticed a media change. */
 105         __u8 toc_valid     : 1; /* Saved TOC information is current. */
 106         __u8 door_locked   : 1; /* We think that the drive door is locked. */
 107         __u8 writing       : 1; /* the drive is currently writing */
 108         __u8 reserved      : 4;
 109         byte current_speed;     /* Current speed of the drive */
 110 };
 111
 112 #define CDROM_STATE_FLAGS(drive) (&(((struct cdrom_info *)(drive->driver_data))->state_flags))
 113
 114 /* Structure of a MSF cdrom address. */
 115 struct atapi_msf {
 116         byte reserved;
 117         byte minute;
 118         byte second;
 119         byte frame;
 120 };
 121
 122 /* Space to hold the disk TOC. */
 123 #define MAX_TRACKS 99
 124 struct atapi_toc_header {
 125         unsigned short toc_length;
 126         byte first_track;
 127         byte last_track;
 128 };
 129
 130 struct atapi_toc_entry {
 131         byte reserved1;
 132 #if defined(__BIG_ENDIAN_BITFIELD)
 133         __u8 adr     : 4;
 134         __u8 control : 4;
 135 #elif defined(__LITTLE_ENDIAN_BITFIELD)
 136         __u8 control : 4;
 137         __u8 adr     : 4;
 138 #else
 139 #error "Please fix <asm/byteorder.h>"
 140 #endif
 141         byte track;
 142         byte reserved2;
 143         union {
 144                 unsigned lba;
 145                 struct atapi_msf msf;
 146         } addr;
 147 };
 148
 149 struct atapi_toc {
 150         int    last_session_lba;
 151         int    xa_flag;
 152         unsigned long capacity;
 153         struct atapi_toc_header hdr;
 154         struct atapi_toc_entry  ent[MAX_TRACKS+1];
 155           /* One extra for the leadout. */
 156 };
 157
 158
 159 /* This structure is annoyingly close to, but not identical with,
 160    the cdrom_subchnl structure from cdrom.h. */
 161 struct atapi_cdrom_subchnl {
 162         u_char  acdsc_reserved;
 163         u_char  acdsc_audiostatus;
 164         u_short acdsc_length;
 165         u_char  acdsc_format;
 166
 167 #if defined(__BIG_ENDIAN_BITFIELD)
 168         u_char  acdsc_ctrl:     4;
 169         u_char  acdsc_adr:      4;
 170 #elif defined(__LITTLE_ENDIAN_BITFIELD)
 171         u_char  acdsc_adr:      4;
 172         u_char  acdsc_ctrl:     4;
 173 #else
 174 #error "Please fix <asm/byteorder.h>"
 175 #endif
 176         u_char  acdsc_trk;
 177         u_char  acdsc_ind;
 178         union {
 179                 struct atapi_msf msf;
 180                 int     lba;
 181         } acdsc_absaddr;
 182         union {
 183                 struct atapi_msf msf;
 184                 int     lba;
 185         } acdsc_reladdr;
 186 };
 187
 188
 189
 190 /* This should probably go into cdrom.h along with the other
 191  * generic stuff now in the Mt. Fuji spec.
 192  */
 193 struct atapi_capabilities_page {
 194         struct mode_page_header header;
 195 #if defined(__BIG_ENDIAN_BITFIELD)
 196         __u8 parameters_saveable : 1;
 197         __u8 reserved1           : 1;
 198         __u8 page_code           : 6;
 199 #elif defined(__LITTLE_ENDIAN_BITFIELD)
 200         __u8 page_code           : 6;
 201         __u8 reserved1           : 1;
 202         __u8 parameters_saveable : 1;
 203 #else
 204 #error "Please fix <asm/byteorder.h>"
 205 #endif
 206
 207         byte     page_length;
 208
 209 #if defined(__BIG_ENDIAN_BITFIELD)
 210         __u8 reserved2           : 2;
 211         /* Drive supports reading of DVD-RAM discs */
 212         __u8 dvd_ram_read        : 1;
 213         /* Drive supports reading of DVD-R discs */
 214         __u8 dvd_r_read          : 1;
 215         /* Drive supports reading of DVD-ROM discs */
 216         __u8 dvd_rom             : 1;
 217         /* Drive supports reading CD-R discs with addressing method 2 */
 218         __u8 method2             : 1; /* reserved in 1.2 */
 219         /* Drive can read from CD-R/W (CD-E) discs (orange book, part III) */
 220         __u8 cd_rw_read          : 1; /* reserved in 1.2 */
 221         /* Drive supports read from CD-R discs (orange book, part II) */
 222         __u8 cd_r_read           : 1; /* reserved in 1.2 */
 223 #elif defined(__LITTLE_ENDIAN_BITFIELD)
 224         /* Drive supports read from CD-R discs (orange book, part II) */
 225         __u8 cd_r_read           : 1; /* reserved in 1.2 */
 226         /* Drive can read from CD-R/W (CD-E) discs (orange book, part III) */
 227         __u8 cd_rw_read          : 1; /* reserved in 1.2 */
 228         /* Drive supports reading CD-R discs with addressing method 2 */
 229         __u8 method2             : 1;
 230         /* Drive supports reading of DVD-ROM discs */
 231         __u8 dvd_rom             : 1;
 232         /* Drive supports reading of DVD-R discs */
 233         __u8 dvd_r_read          : 1;
 234         /* Drive supports reading of DVD-RAM discs */
 235         __u8 dvd_ram_read        : 1;
 236         __u8 reserved2           : 2;
 237 #else
 238 #error "Please fix <asm/byteorder.h>"
 239 #endif
 240
 241 #if defined(__BIG_ENDIAN_BITFIELD)
 242         __u8 reserved3           : 2;
 243         /* Drive can write DVD-RAM discs */
 244         __u8 dvd_ram_write       : 1;
 245         /* Drive can write DVD-R discs */
 246         __u8 dvd_r_write         : 1;
 247         __u8 reserved3a          : 1;
 248         /* Drive can fake writes */
 249         __u8 test_write          : 1;
 250         /* Drive can write to CD-R/W (CD-E) discs (orange book, part III) */
 251         __u8 cd_rw_write         : 1; /* reserved in 1.2 */
 252         /* Drive supports write to CD-R discs (orange book, part II) */
 253         __u8 cd_r_write          : 1; /* reserved in 1.2 */
 254 #elif defined(__LITTLE_ENDIAN_BITFIELD)
 255         /* Drive can write to CD-R discs (orange book, part II) */
 256         __u8 cd_r_write          : 1; /* reserved in 1.2 */
 257         /* Drive can write to CD-R/W (CD-E) discs (orange book, part III) */
 258         __u8 cd_rw_write         : 1; /* reserved in 1.2 */
 259         /* Drive can fake writes */
 260         __u8 test_write          : 1;
 261         __u8 reserved3a          : 1;
 262         /* Drive can write DVD-R discs */
 263         __u8 dvd_r_write         : 1;
 264         /* Drive can write DVD-RAM discs */
 265         __u8 dvd_ram_write       : 1;
 266         __u8 reserved3           : 2;
 267 #else
 268 #error "Please fix <asm/byteorder.h>"
 269 #endif
 270
 271 #if defined(__BIG_ENDIAN_BITFIELD)
 272         __u8 reserved4           : 1;
 273         /* Drive can read multisession discs. */
 274         __u8 multisession        : 1;
 275         /* Drive can read mode 2, form 2 data. */
 276         __u8 mode2_form2         : 1;
 277         /* Drive can read mode 2, form 1 (XA) data. */
 278         __u8 mode2_form1         : 1;
 279         /* Drive supports digital output on port 2. */
 280         __u8 digport2            : 1;
 281         /* Drive supports digital output on port 1. */
 282         __u8 digport1            : 1;
 283         /* Drive can deliver a composite audio/video data stream. */
 284         __u8 composite           : 1;
 285         /* Drive supports audio play operations. */
 286         __u8 audio_play          : 1;
 287 #elif defined(__LITTLE_ENDIAN_BITFIELD)
 288         /* Drive supports audio play operations. */
 289         __u8 audio_play          : 1;
 290         /* Drive can deliver a composite audio/video data stream. */
 291         __u8 composite           : 1;
 292         /* Drive supports digital output on port 1. */
 293         __u8 digport1            : 1;
 294         /* Drive supports digital output on port 2. */
 295         __u8 digport2            : 1;
 296         /* Drive can read mode 2, form 1 (XA) data. */
 297         __u8 mode2_form1         : 1;
 298         /* Drive can read mode 2, form 2 data. */
 299         __u8 mode2_form2         : 1;
 300         /* Drive can read multisession discs. */
 301         __u8 multisession        : 1;
 302         __u8 reserved4           : 1;
 303 #else
 304 #error "Please fix <asm/byteorder.h>"
 305 #endif
 306
 307 #if defined(__BIG_ENDIAN_BITFIELD)
 308         __u8 reserved5           : 1;
 309         /* Drive can return Media Catalog Number (UPC) info. */
 310         __u8 upc                 : 1;
 311         /* Drive can return International Standard Recording Code info. */
 312         __u8 isrc                : 1;
 313         /* Drive supports C2 error pointers. */
 314         __u8 c2_pointers         : 1;
 315         /* R-W data will be returned deinterleaved and error corrected. */
 316         __u8 rw_corr             : 1;
 317         /* Subchannel reads can return combined R-W information. */
 318         __u8 rw_supported        : 1;
 319         /* Drive can continue a read cdda operation from a loss of streaming.*/
 320         __u8 cdda_accurate       : 1;
 321         /* Drive can read Red Book audio data. */
 322         __u8 cdda                : 1;
 323 #elif defined(__LITTLE_ENDIAN_BITFIELD)
 324         /* Drive can read Red Book audio data. */
 325         __u8 cdda                : 1;
 326         /* Drive can continue a read cdda operation from a loss of streaming.*/
 327         __u8 cdda_accurate       : 1;
 328         /* Subchannel reads can return combined R-W information. */
 329         __u8 rw_supported        : 1;
 330         /* R-W data will be returned deinterleaved and error corrected. */
 331         __u8 rw_corr             : 1;
 332         /* Drive supports C2 error pointers. */
 333         __u8 c2_pointers         : 1;
 334         /* Drive can return International Standard Recording Code info. */
 335         __u8 isrc                : 1;
 336         /* Drive can return Media Catalog Number (UPC) info. */
 337         __u8 upc                 : 1;
 338         __u8 reserved5           : 1;
 339 #else
 340 #error "Please fix <asm/byteorder.h>"
 341 #endif
 342
 343 #if defined(__BIG_ENDIAN_BITFIELD)
 344         /* Drive mechanism types. */
 345         mechtype_t mechtype      : 3;
 346         __u8 reserved6           : 1;
 347         /* Drive can eject a disc or changer cartridge. */
 348         __u8 eject               : 1;
 349         /* State of prevent/allow jumper. */
 350         __u8 prevent_jumper      : 1;
 351         /* Present state of door lock. */
 352         __u8 lock_state          : 1;
 353         /* Drive can lock the door. */
 354         __u8 lock                : 1;
 355 #elif defined(__LITTLE_ENDIAN_BITFIELD)
 356
 357         /* Drive can lock the door. */
 358         __u8 lock                : 1;
 359         /* Present state of door lock. */
 360         __u8 lock_state          : 1;
 361         /* State of prevent/allow jumper. */
 362         __u8 prevent_jumper      : 1;
 363         /* Drive can eject a disc or changer cartridge. */
 364         __u8 eject               : 1;
 365         __u8 reserved6           : 1;
 366         /* Drive mechanism types. */
 367         mechtype_t mechtype      : 3;
 368 #else
 369 #error "Please fix <asm/byteorder.h>"
 370 #endif
 371
 372 #if defined(__BIG_ENDIAN_BITFIELD)
 373         __u8 reserved7           : 4;
 374         /* Drive supports software slot selection. */
 375         __u8 sss                 : 1;  /* reserved in 1.2 */
 376         /* Changer can report exact contents of slots. */
 377         __u8 disc_present        : 1;  /* reserved in 1.2 */
 378         /* Audio for each channel can be muted independently. */
 379         __u8 separate_mute       : 1;
 380         /* Audio level for each channel can be controlled independently. */
 381         __u8 separate_volume     : 1;
 382 #elif defined(__LITTLE_ENDIAN_BITFIELD)
 383
 384         /* Audio level for each channel can be controlled independently. */
 385         __u8 separate_volume     : 1;
 386         /* Audio for each channel can be muted independently. */
 387         __u8 separate_mute       : 1;
 388         /* Changer can report exact contents of slots. */
 389         __u8 disc_present        : 1;  /* reserved in 1.2 */
 390         /* Drive supports software slot selection. */
 391         __u8 sss                 : 1;  /* reserved in 1.2 */
 392         __u8 reserved7           : 4;
 393 #else
 394 #error "Please fix <asm/byteorder.h>"
 395 #endif
 396
 397         /* Note: the following four fields are returned in big-endian form. */
 398         /* Maximum speed (in kB/s). */
 399         unsigned short maxspeed;
 400         /* Number of discrete volume levels. */
 401         unsigned short n_vol_levels;
 402         /* Size of cache in drive, in kB. */
 403         unsigned short buffer_size;
 404         /* Current speed (in kB/s). */
 405         unsigned short curspeed;
 406         char pad[4];
 407 };
 408
 409
 410 struct atapi_mechstat_header {
 411 #if defined(__BIG_ENDIAN_BITFIELD)
 412         __u8 fault         : 1;
 413         __u8 changer_state : 2;
 414         __u8 curslot       : 5;
 415 #elif defined(__LITTLE_ENDIAN_BITFIELD)
 416         __u8 curslot       : 5;
 417         __u8 changer_state : 2;
 418         __u8 fault         : 1;
 419 #else
 420 #error "Please fix <asm/byteorder.h>"
 421 #endif
 422
 423 #if defined(__BIG_ENDIAN_BITFIELD)
 424         __u8 mech_state    : 3;
 425         __u8 door_open     : 1;
 426         __u8 reserved1     : 4;
 427 #elif defined(__LITTLE_ENDIAN_BITFIELD)
 428         __u8 reserved1     : 4;
 429         __u8 door_open     : 1;
 430         __u8 mech_state    : 3;
 431 #else
 432 #error "Please fix <asm/byteorder.h>"
 433 #endif
 434
 435         byte     curlba[3];
 436         byte     nslots;
 437         __u16    slot_tablelen;
 438 };
 439
 440
 441 struct atapi_slot {
 442 #if defined(__BIG_ENDIAN_BITFIELD)
 443         __u8 disc_present : 1;
 444         __u8 reserved1    : 6;
 445         __u8 change       : 1;
 446 #elif defined(__LITTLE_ENDIAN_BITFIELD)
 447         __u8 change       : 1;
 448         __u8 reserved1    : 6;
 449         __u8 disc_present : 1;
 450 #else
 451 #error "Please fix <asm/byteorder.h>"
 452 #endif
 453
 454         byte reserved2[3];
 455 };
 456
 457 struct atapi_changer_info {
 458         struct atapi_mechstat_header hdr;
 459         struct atapi_slot slots[0];
 460 };
 461
 462 /* Extra per-device info for cdrom drives. */
 463 struct cdrom_info {
 464         ide_drive_t     *drive;
 465         ide_driver_t    *driver;
 466         struct gendisk  *disk;
 467         struct kref     kref;
 468
 469         /* Buffer for table of contents.  NULL if we haven't allocated
 470            a TOC buffer for this device yet. */
 471
 472         struct atapi_toc *toc;
 473
 474         unsigned long   sector_buffered;
 475         unsigned long   nsectors_buffered;
 476         unsigned char   *buffer;
 477
 478         /* The result of the last successful request sense command
 479            on this device. */
 480         struct request_sense sense_data;
 481
 482         struct request request_sense_request;
 483         int dma;
 484         unsigned long last_block;
 485         unsigned long start_seek;
 486         /* Buffer to hold mechanism status and changer slot table. */
 487         struct atapi_changer_info *changer_info;
 488
 489         struct ide_cd_config_flags      config_flags;
 490         struct ide_cd_state_flags       state_flags;
 491
 492         /* Per-device info needed by cdrom.c generic driver. */
 493         struct cdrom_device_info devinfo;
 494
 495         unsigned long write_timeout;
 496 };
 497
 498 /****************************************************************************
 499  * Descriptions of ATAPI error codes.
 500  */
 501
 502 /* This stuff should be in cdrom.h, since it is now generic... */
 503
 504 /* ATAPI sense keys (from table 140 of ATAPI 2.6) */
 505 #define NO_SENSE                0x00
 506 #define RECOVERED_ERROR         0x01
 507 #define NOT_READY               0x02
 508 #define MEDIUM_ERROR            0x03
 509 #define HARDWARE_ERROR          0x04
 510 #define ILLEGAL_REQUEST         0x05
 511 #define UNIT_ATTENTION          0x06
 512 #define DATA_PROTECT            0x07
 513 #define BLANK_CHECK             0x08
 514 #define ABORTED_COMMAND         0x0b
 515 #define MISCOMPARE              0x0e
 516
 517
 518
 519 /* This stuff should be in cdrom.h, since it is now generic... */
 520 #if VERBOSE_IDE_CD_ERRORS
 521
 522  /* The generic packet command opcodes for CD/DVD Logical Units,
 523  * From Table 57 of the SFF8090 Ver. 3 (Mt. Fuji) draft standard. */
 524 static const struct {
 525         unsigned short packet_command;
 526         const char * const text;
 527 } packet_command_texts[] = {
 528         { GPCMD_TEST_UNIT_READY, "Test Unit Ready" },
 529         { GPCMD_REQUEST_SENSE, "Request Sense" },
 530         { GPCMD_FORMAT_UNIT, "Format Unit" },
 531         { GPCMD_INQUIRY, "Inquiry" },
 532         { GPCMD_START_STOP_UNIT, "Start/Stop Unit" },
 533         { GPCMD_PREVENT_ALLOW_MEDIUM_REMOVAL, "Prevent/Allow Medium Removal" },
 534         { GPCMD_READ_FORMAT_CAPACITIES, "Read Format Capacities" },
 535         { GPCMD_READ_CDVD_CAPACITY, "Read Cd/Dvd Capacity" },
 536         { GPCMD_READ_10, "Read 10" },
 537         { GPCMD_WRITE_10, "Write 10" },
 538         { GPCMD_SEEK, "Seek" },
 539         { GPCMD_WRITE_AND_VERIFY_10, "Write and Verify 10" },
 540         { GPCMD_VERIFY_10, "Verify 10" },
 541         { GPCMD_FLUSH_CACHE, "Flush Cache" },
 542         { GPCMD_READ_SUBCHANNEL, "Read Subchannel" },
 543         { GPCMD_READ_TOC_PMA_ATIP, "Read Table of Contents" },
 544         { GPCMD_READ_HEADER, "Read Header" },
 545         { GPCMD_PLAY_AUDIO_10, "Play Audio 10" },
 546         { GPCMD_GET_CONFIGURATION, "Get Configuration" },
 547         { GPCMD_PLAY_AUDIO_MSF, "Play Audio MSF" },
 548         { GPCMD_PLAYAUDIO_TI, "Play Audio TrackIndex" },
 549         { GPCMD_GET_EVENT_STATUS_NOTIFICATION, "Get Event Status Notification" },
 550         { GPCMD_PAUSE_RESUME, "Pause/Resume" },
 551         { GPCMD_STOP_PLAY_SCAN, "Stop Play/Scan" },
 552         { GPCMD_READ_DISC_INFO, "Read Disc Info" },
 553         { GPCMD_READ_TRACK_RZONE_INFO, "Read Track Rzone Info" },
 554         { GPCMD_RESERVE_RZONE_TRACK, "Reserve Rzone Track" },
 555         { GPCMD_SEND_OPC, "Send OPC" },
 556         { GPCMD_MODE_SELECT_10, "Mode Select 10" },
 557         { GPCMD_REPAIR_RZONE_TRACK, "Repair Rzone Track" },
 558         { GPCMD_MODE_SENSE_10, "Mode Sense 10" },
 559         { GPCMD_CLOSE_TRACK, "Close Track" },
 560         { GPCMD_BLANK, "Blank" },
 561         { GPCMD_SEND_EVENT, "Send Event" },
 562         { GPCMD_SEND_KEY, "Send Key" },
 563         { GPCMD_REPORT_KEY, "Report Key" },
 564         { GPCMD_LOAD_UNLOAD, "Load/Unload" },
 565         { GPCMD_SET_READ_AHEAD, "Set Read-ahead" },
 566         { GPCMD_READ_12, "Read 12" },
 567         { GPCMD_GET_PERFORMANCE, "Get Performance" },
 568         { GPCMD_SEND_DVD_STRUCTURE, "Send DVD Structure" },
 569         { GPCMD_READ_DVD_STRUCTURE, "Read DVD Structure" },
 570         { GPCMD_SET_STREAMING, "Set Streaming" },
 571         { GPCMD_READ_CD_MSF, "Read CD MSF" },
 572         { GPCMD_SCAN, "Scan" },
 573         { GPCMD_SET_SPEED, "Set Speed" },
 574         { GPCMD_PLAY_CD, "Play CD" },
 575         { GPCMD_MECHANISM_STATUS, "Mechanism Status" },
 576         { GPCMD_READ_CD, "Read CD" },
 577 };
 578
 579
 580
 581 /* From Table 303 of the SFF8090 Ver. 3 (Mt. Fuji) draft standard. */
 582 static const char * const sense_key_texts[16] = {
 583         "No sense data",
 584         "Recovered error",
 585         "Not ready",
 586         "Medium error",
 587         "Hardware error",
 588         "Illegal request",
 589         "Unit attention",
 590         "Data protect",
 591         "Blank check",
 592         "(reserved)",
 593         "(reserved)",
 594         "Aborted command",
 595         "(reserved)",
 596         "(reserved)",
 597         "Miscompare",
 598         "(reserved)",
 599 };
 600
 601 /* From Table 304 of the SFF8090 Ver. 3 (Mt. Fuji) draft standard. */
 602 static const struct {
 603         unsigned long asc_ascq;
 604         const char * const text;
 605 } sense_data_texts[] = {
 606         { 0x000000, "No additional sense information" },
 607         { 0x000011, "Play operation in progress" },
 608         { 0x000012, "Play operation paused" },
 609         { 0x000013, "Play operation successfully completed" },
 610         { 0x000014, "Play operation stopped due to error" },
 611         { 0x000015, "No current audio status to return" },
 612         { 0x010c0a, "Write error - padding blocks added" },
 613         { 0x011700, "Recovered data with no error correction applied" },
 614         { 0x011701, "Recovered data with retries" },
 615         { 0x011702, "Recovered data with positive head offset" },
 616         { 0x011703, "Recovered data with negative head offset" },
 617         { 0x011704, "Recovered data with retries and/or CIRC applied" },
 618         { 0x011705, "Recovered data using previous sector ID" },
 619         { 0x011800, "Recovered data with error correction applied" },
 620         { 0x011801, "Recovered data with error correction and retries applied"},
 621         { 0x011802, "Recovered data - the data was auto-reallocated" },
 622         { 0x011803, "Recovered data with CIRC" },
 623         { 0x011804, "Recovered data with L-EC" },
 624         { 0x015d00,
 625             "Failure prediction threshold exceeded - Predicted logical unit failure" },
 626         { 0x015d01,
 627             "Failure prediction threshold exceeded - Predicted media failure" },
 628         { 0x015dff, "Failure prediction threshold exceeded - False" },
 629         { 0x017301, "Power calibration area almost full" },
 630         { 0x020400, "Logical unit not ready - cause not reportable" },
 631         /* Following is misspelled in ATAPI 2.6, _and_ in Mt. Fuji */
 632         { 0x020401,
 633           "Logical unit not ready - in progress [sic] of becoming ready" },
 634         { 0x020402, "Logical unit not ready - initializing command required" },
 635         { 0x020403, "Logical unit not ready - manual intervention required" },
 636         { 0x020404, "Logical unit not ready - format in progress" },
 637         { 0x020407, "Logical unit not ready - operation in progress" },
 638         { 0x020408, "Logical unit not ready - long write in progress" },
 639         { 0x020600, "No reference position found (media may be upside down)" },
 640         { 0x023000, "Incompatible medium installed" },
 641         { 0x023a00, "Medium not present" },
 642         { 0x025300, "Media load or eject failed" },
 643         { 0x025700, "Unable to recover table of contents" },
 644         { 0x030300, "Peripheral device write fault" },
 645         { 0x030301, "No write current" },
 646         { 0x030302, "Excessive write errors" },
 647         { 0x030c00, "Write error" },
 648         { 0x030c01, "Write error - Recovered with auto reallocation" },
 649         { 0x030c02, "Write error - auto reallocation failed" },
 650         { 0x030c03, "Write error - recommend reassignment" },
 651         { 0x030c04, "Compression check miscompare error" },
 652         { 0x030c05, "Data expansion occurred during compress" },
 653         { 0x030c06, "Block not compressible" },
 654         { 0x030c07, "Write error - recovery needed" },
 655         { 0x030c08, "Write error - recovery failed" },
 656         { 0x030c09, "Write error - loss of streaming" },
 657         { 0x031100, "Unrecovered read error" },
 658         { 0x031106, "CIRC unrecovered error" },
 659         { 0x033101, "Format command failed" },
 660         { 0x033200, "No defect spare location available" },
 661         { 0x033201, "Defect list update failure" },
 662         { 0x035100, "Erase failure" },
 663         { 0x037200, "Session fixation error" },
 664         { 0x037201, "Session fixation error writin lead-in" },
 665         { 0x037202, "Session fixation error writin lead-out" },
 666         { 0x037300, "CD control error" },
 667         { 0x037302, "Power calibration area is full" },
 668         { 0x037303, "Power calibration area error" },
 669         { 0x037304, "Program memory area / RMA update failure" },
 670         { 0x037305, "Program memory area / RMA is full" },
 671         { 0x037306, "Program memory area / RMA is (almost) full" },
 672
 673         { 0x040200, "No seek complete" },
 674         { 0x040300, "Write fault" },
 675         { 0x040900, "Track following error" },
 676         { 0x040901, "Tracking servo failure" },
 677         { 0x040902, "Focus servo failure" },
 678         { 0x040903, "Spindle servo failure" },
 679         { 0x041500, "Random positioning error" },
 680         { 0x041501, "Mechanical positioning or changer error" },
 681         { 0x041502, "Positioning error detected by read of medium" },
 682         { 0x043c00, "Mechanical positioning or changer error" },
 683         { 0x044000, "Diagnostic failure on component (ASCQ)" },
 684         { 0x044400, "Internal CD/DVD logical unit failure" },
 685         { 0x04b600, "Media load mechanism failed" },
 686         { 0x051a00, "Parameter list length error" },
 687         { 0x052000, "Invalid command operation code" },
 688         { 0x052100, "Logical block address out of range" },
 689         { 0x052102, "Invalid address for write" },
 690         { 0x052400, "Invalid field in command packet" },
 691         { 0x052600, "Invalid field in parameter list" },
 692         { 0x052601, "Parameter not supported" },
 693         { 0x052602, "Parameter value invalid" },
 694         { 0x052700, "Write protected media" },
 695         { 0x052c00, "Command sequence error" },
 696         { 0x052c03, "Current program area is not empty" },
 697         { 0x052c04, "Current program area is empty" },
 698         { 0x053001, "Cannot read medium - unknown format" },
 699         { 0x053002, "Cannot read medium - incompatible format" },
 700         { 0x053900, "Saving parameters not supported" },
 701         { 0x054e00, "Overlapped commands attempted" },
 702         { 0x055302, "Medium removal prevented" },
 703         { 0x055500, "System resource failure" },
 704         { 0x056300, "End of user area encountered on this track" },
 705         { 0x056400, "Illegal mode for this track or incompatible medium" },
 706         { 0x056f00, "Copy protection key exchange failure - Authentication failure" },
 707         { 0x056f01, "Copy protection key exchange failure - Key not present" },
 708         { 0x056f02, "Copy protection key exchange failure - Key not established" },
 709         { 0x056f03, "Read of scrambled sector without authentication" },
 710         { 0x056f04, "Media region code is mismatched to logical unit" },
 711         { 0x056f05,  "Drive region must be permanent / region reset count error" },
 712         { 0x057203, "Session fixation error - incomplete track in session" },
 713         { 0x057204, "Empty or partially written reserved track" },
 714         { 0x057205, "No more RZONE reservations are allowed" },
 715         { 0x05bf00, "Loss of streaming" },
 716         { 0x062800, "Not ready to ready transition, medium may have changed" },
 717         { 0x062900, "Power on, reset or hardware reset occurred" },
 718         { 0x062a00, "Parameters changed" },
 719         { 0x062a01, "Mode parameters changed" },
 720         { 0x062e00, "Insufficient time for operation" },
 721         { 0x063f00, "Logical unit operating conditions have changed" },
 722         { 0x063f01, "Microcode has been changed" },
 723         { 0x065a00, "Operator request or state change input (unspecified)" },
 724         { 0x065a01, "Operator medium removal request" },
 725         { 0x0bb900, "Play operation aborted" },
 726
 727         /* Here we use 0xff for the key (not a valid key) to signify
 728          * that these can have _any_ key value associated with them... */
 729         { 0xff0401, "Logical unit is in process of becoming ready" },
 730         { 0xff0400, "Logical unit not ready, cause not reportable" },
 731         { 0xff0402, "Logical unit not ready, initializing command required" },
 732         { 0xff0403, "Logical unit not ready, manual intervention required" },
 733         { 0xff0500, "Logical unit does not respond to selection" },
 734         { 0xff0800, "Logical unit communication failure" },
 735         { 0xff0802, "Logical unit communication parity error" },
 736         { 0xff0801, "Logical unit communication time-out" },
 737         { 0xff2500, "Logical unit not supported" },
 738         { 0xff4c00, "Logical unit failed self-configuration" },
 739         { 0xff3e00, "Logical unit has not self-configured yet" },
 740 };
 741 #endif
 742
 743
 744 #endif /* _IDE_CD_H */