include/asm-powerpc/dma.h

   1 #ifndef _ASM_POWERPC_DMA_H
   2 #define _ASM_POWERPC_DMA_H
   3 #ifdef __KERNEL__
   4
   5 /*
   6  * Defines for using and allocating dma channels.
   7  * Written by Hennus Bergman, 1992.
   8  * High DMA channel support & info by Hannu Savolainen
   9  * and John Boyd, Nov. 1992.
  10  * Changes for ppc sound by Christoph Nadig
  11  */
  12
  13 /*
  14  * Note: Adapted for PowerPC by Gary Thomas
  15  * Modified by Cort Dougan <cort@cs.nmt.edu>
  16  *
  17  * None of this really applies for Power Macintoshes.  There is
  18  * basically just enough here to get kernel/dma.c to compile.
  19  *
  20  * There may be some comments or restrictions made here which are
  21  * not valid for the PReP platform.  Take what you read
  22  * with a grain of salt.
  23  */
  24
  25 #include <asm/io.h>
  26 #include <linux/spinlock.h>
  27 #include <asm/system.h>
  28
  29 #ifndef MAX_DMA_CHANNELS
  30 #define MAX_DMA_CHANNELS        8
  31 #endif
  32
  33 /* The maximum address that we can perform a DMA transfer to on this platform */
  34 /* Doesn't really apply... */
  35 #define MAX_DMA_ADDRESS         (~0UL)
  36
  37 #if !defined(CONFIG_PPC_ISERIES) || defined(CONFIG_PCI)
  38
  39 #ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER
  40 #define dma_outb        outb_p
  41 #else
  42 #define dma_outb        outb
  43 #endif
  44
  45 #define dma_inb         inb
  46
  47 /*
  48  * NOTES about DMA transfers:
  49  *
  50  *  controller 1: channels 0-3, byte operations, ports 00-1F
  51  *  controller 2: channels 4-7, word operations, ports C0-DF
  52  *
  53  *  - ALL registers are 8 bits only, regardless of transfer size
  54  *  - channel 4 is not used - cascades 1 into 2.
  55  *  - channels 0-3 are byte - addresses/counts are for physical bytes
  56  *  - channels 5-7 are word - addresses/counts are for physical words
  57  *  - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries
  58  *  - transfer count loaded to registers is 1 less than actual count
  59  *  - controller 2 offsets are all even (2x offsets for controller 1)
  60  *  - page registers for 5-7 don't use data bit 0, represent 128K pages
  61  *  - page registers for 0-3 use bit 0, represent 64K pages
  62  *
  63  * On PReP, DMA transfers are limited to the lower 16MB of _physical_ memory.
  64  * On CHRP, the W83C553F (and VLSI Tollgate?) support full 32 bit addressing.
  65  * Note that addresses loaded into registers must be _physical_ addresses,
  66  * not logical addresses (which may differ if paging is active).
  67  *
  68  *  Address mapping for channels 0-3:
  69  *
  70  *   A23 ... A16 A15 ... A8  A7 ... A0    (Physical addresses)
  71  *    |  ...  |   |  ... |   |  ... |
  72  *    |  ...  |   |  ... |   |  ... |
  73  *    |  ...  |   |  ... |   |  ... |
  74  *   P7  ...  P0  A7 ... A0  A7 ... A0
  75  * |    Page    | Addr MSB | Addr LSB |   (DMA registers)
  76  *
  77  *  Address mapping for channels 5-7:
  78  *
  79  *   A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0    (Physical addresses)
  80  *    |  ...  |   \   \   ... \  \  \  ... \  \
  81  *    |  ...  |    \   \   ... \  \  \  ... \  (not used)
  82  *    |  ...  |     \   \   ... \  \  \  ... \
  83  *   P7  ...  P1 (0) A7 A6  ... A0 A7 A6 ... A0
  84  * |      Page      |  Addr MSB   |  Addr LSB  |   (DMA registers)
  85  *
  86  * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses
  87  * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at
  88  * the hardware level, so odd-byte transfers aren't possible).
  89  *
  90  * Transfer count (_not # bytes_) is limited to 64K, represented as actual
  91  * count - 1 : 64K => 0xFFFF, 1 => 0x0000.  Thus, count is always 1 or more,
  92  * and up to 128K bytes may be transferred on channels 5-7 in one operation.
  93  *
  94  */
  95
  96 /* 8237 DMA controllers */
  97 #define IO_DMA1_BASE    0x00    /* 8 bit slave DMA, channels 0..3 */
  98 #define IO_DMA2_BASE    0xC0    /* 16 bit master DMA, ch 4(=slave input)..7 */
  99
 100 /* DMA controller registers */
 101 #define DMA1_CMD_REG            0x08    /* command register (w) */
 102 #define DMA1_STAT_REG           0x08    /* status register (r) */
 103 #define DMA1_REQ_REG            0x09    /* request register (w) */
 104 #define DMA1_MASK_REG           0x0A    /* single-channel mask (w) */
 105 #define DMA1_MODE_REG           0x0B    /* mode register (w) */
 106 #define DMA1_CLEAR_FF_REG       0x0C    /* clear pointer flip-flop (w) */
 107 #define DMA1_TEMP_REG           0x0D    /* Temporary Register (r) */
 108 #define DMA1_RESET_REG          0x0D    /* Master Clear (w) */
 109 #define DMA1_CLR_MASK_REG       0x0E    /* Clear Mask */
 110 #define DMA1_MASK_ALL_REG       0x0F    /* all-channels mask (w) */
 111
 112 #define DMA2_CMD_REG            0xD0    /* command register (w) */
 113 #define DMA2_STAT_REG           0xD0    /* status register (r) */
 114 #define DMA2_REQ_REG            0xD2    /* request register (w) */
 115 #define DMA2_MASK_REG           0xD4    /* single-channel mask (w) */
 116 #define DMA2_MODE_REG           0xD6    /* mode register (w) */
 117 #define DMA2_CLEAR_FF_REG       0xD8    /* clear pointer flip-flop (w) */
 118 #define DMA2_TEMP_REG           0xDA    /* Temporary Register (r) */
 119 #define DMA2_RESET_REG          0xDA    /* Master Clear (w) */
 120 #define DMA2_CLR_MASK_REG       0xDC    /* Clear Mask */
 121 #define DMA2_MASK_ALL_REG       0xDE    /* all-channels mask (w) */
 122
 123 #define DMA_ADDR_0              0x00    /* DMA address registers */
 124 #define DMA_ADDR_1              0x02
 125 #define DMA_ADDR_2              0x04
 126 #define DMA_ADDR_3              0x06
 127 #define DMA_ADDR_4              0xC0
 128 #define DMA_ADDR_5              0xC4
 129 #define DMA_ADDR_6              0xC8
 130 #define DMA_ADDR_7              0xCC
 131
 132 #define DMA_CNT_0               0x01    /* DMA count registers */
 133 #define DMA_CNT_1               0x03
 134 #define DMA_CNT_2               0x05
 135 #define DMA_CNT_3               0x07
 136 #define DMA_CNT_4               0xC2
 137 #define DMA_CNT_5               0xC6
 138 #define DMA_CNT_6               0xCA
 139 #define DMA_CNT_7               0xCE
 140
 141 #define DMA_LO_PAGE_0           0x87    /* DMA page registers */
 142 #define DMA_LO_PAGE_1           0x83
 143 #define DMA_LO_PAGE_2           0x81
 144 #define DMA_LO_PAGE_3           0x82
 145 #define DMA_LO_PAGE_5           0x8B
 146 #define DMA_LO_PAGE_6           0x89
 147 #define DMA_LO_PAGE_7           0x8A
 148
 149 #define DMA_HI_PAGE_0           0x487   /* DMA page registers */
 150 #define DMA_HI_PAGE_1           0x483
 151 #define DMA_HI_PAGE_2           0x481
 152 #define DMA_HI_PAGE_3           0x482
 153 #define DMA_HI_PAGE_5           0x48B
 154 #define DMA_HI_PAGE_6           0x489
 155 #define DMA_HI_PAGE_7           0x48A
 156
 157 #define DMA1_EXT_REG            0x40B
 158 #define DMA2_EXT_REG            0x4D6
 159
 160 #ifndef __powerpc64__
 161     /* in arch/ppc/kernel/setup.c -- Cort */
 162     extern unsigned int DMA_MODE_WRITE;
 163     extern unsigned int DMA_MODE_READ;
 164     extern unsigned long ISA_DMA_THRESHOLD;
 165 #else
 166     #define DMA_MODE_READ       0x44    /* I/O to memory, no autoinit, increment, single mode */
 167     #define DMA_MODE_WRITE      0x48    /* memory to I/O, no autoinit, increment, single mode */
 168 #endif
 169
 170 #define DMA_MODE_CASCADE        0xC0    /* pass thru DREQ->HRQ, DACK<-HLDA only */
 171
 172 #define DMA_AUTOINIT            0x10
 173
 174 extern spinlock_t dma_spin_lock;
 175
 176 static __inline__ unsigned long claim_dma_lock(void)
 177 {
 178         unsigned long flags;
 179         spin_lock_irqsave(&dma_spin_lock, flags);
 180         return flags;
 181 }
 182
 183 static __inline__ void release_dma_lock(unsigned long flags)
 184 {
 185         spin_unlock_irqrestore(&dma_spin_lock, flags);
 186 }
 187
 188 /* enable/disable a specific DMA channel */
 189 static __inline__ void enable_dma(unsigned int dmanr)
 190 {
 191         unsigned char ucDmaCmd = 0x00;
 192
 193         if (dmanr != 4) {
 194                 dma_outb(0, DMA2_MASK_REG);     /* This may not be enabled */
 195                 dma_outb(ucDmaCmd, DMA2_CMD_REG);       /* Enable group */
 196         }
 197         if (dmanr <= 3) {
 198                 dma_outb(dmanr, DMA1_MASK_REG);
 199                 dma_outb(ucDmaCmd, DMA1_CMD_REG);       /* Enable group */
 200         } else {
 201                 dma_outb(dmanr & 3, DMA2_MASK_REG);
 202         }
 203 }
 204
 205 static __inline__ void disable_dma(unsigned int dmanr)
 206 {
 207         if (dmanr <= 3)
 208                 dma_outb(dmanr | 4, DMA1_MASK_REG);
 209         else
 210                 dma_outb((dmanr & 3) | 4, DMA2_MASK_REG);
 211 }
 212
 213 /* Clear the 'DMA Pointer Flip Flop'.
 214  * Write 0 for LSB/MSB, 1 for MSB/LSB access.
 215  * Use this once to initialize the FF to a known state.
 216  * After that, keep track of it. :-)
 217  * --- In order to do that, the DMA routines below should ---
 218  * --- only be used while interrupts are disabled! ---
 219  */
 220 static __inline__ void clear_dma_ff(unsigned int dmanr)
 221 {
 222         if (dmanr <= 3)
 223                 dma_outb(0, DMA1_CLEAR_FF_REG);
 224         else
 225                 dma_outb(0, DMA2_CLEAR_FF_REG);
 226 }
 227
 228 /* set mode (above) for a specific DMA channel */
 229 static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
 230 {
 231         if (dmanr <= 3)
 232                 dma_outb(mode | dmanr, DMA1_MODE_REG);
 233         else
 234                 dma_outb(mode | (dmanr & 3), DMA2_MODE_REG);
 235 }
 236
 237 /* Set only the page register bits of the transfer address.
 238  * This is used for successive transfers when we know the contents of
 239  * the lower 16 bits of the DMA current address register, but a 64k boundary
 240  * may have been crossed.
 241  */
 242 static __inline__ void set_dma_page(unsigned int dmanr, int pagenr)
 243 {
 244         switch (dmanr) {
 245         case 0:
 246                 dma_outb(pagenr, DMA_LO_PAGE_0);
 247                 dma_outb(pagenr >> 8, DMA_HI_PAGE_0);
 248                 break;
 249         case 1:
 250                 dma_outb(pagenr, DMA_LO_PAGE_1);
 251                 dma_outb(pagenr >> 8, DMA_HI_PAGE_1);
 252                 break;
 253         case 2:
 254                 dma_outb(pagenr, DMA_LO_PAGE_2);
 255                 dma_outb(pagenr >> 8, DMA_HI_PAGE_2);
 256                 break;
 257         case 3:
 258                 dma_outb(pagenr, DMA_LO_PAGE_3);
 259                 dma_outb(pagenr >> 8, DMA_HI_PAGE_3);
 260                 break;
 261         case 5:
 262                 dma_outb(pagenr & 0xfe, DMA_LO_PAGE_5);
 263                 dma_outb(pagenr >> 8, DMA_HI_PAGE_5);
 264                 break;
 265         case 6:
 266                 dma_outb(pagenr & 0xfe, DMA_LO_PAGE_6);
 267                 dma_outb(pagenr >> 8, DMA_HI_PAGE_6);
 268                 break;
 269         case 7:
 270                 dma_outb(pagenr & 0xfe, DMA_LO_PAGE_7);
 271                 dma_outb(pagenr >> 8, DMA_HI_PAGE_7);
 272                 break;
 273         }
 274 }
 275
 276 /* Set transfer address & page bits for specific DMA channel.
 277  * Assumes dma flipflop is clear.
 278  */
 279 static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int phys)
 280 {
 281         if (dmanr <= 3) {
 282                 dma_outb(phys & 0xff,
 283                          ((dmanr & 3) << 1) + IO_DMA1_BASE);
 284                 dma_outb((phys >> 8) & 0xff,
 285                          ((dmanr & 3) << 1) + IO_DMA1_BASE);
 286         } else {
 287                 dma_outb((phys >> 1) & 0xff,
 288                          ((dmanr & 3) << 2) + IO_DMA2_BASE);
 289                 dma_outb((phys >> 9) & 0xff,
 290                          ((dmanr & 3) << 2) + IO_DMA2_BASE);
 291         }
 292         set_dma_page(dmanr, phys >> 16);
 293 }
 294
 295
 296 /* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for
 297  * a specific DMA channel.
 298  * You must ensure the parameters are valid.
 299  * NOTE: from a manual: "the number of transfers is one more
 300  * than the initial word count"! This is taken into account.
 301  * Assumes dma flip-flop is clear.
 302  * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
 303  */
 304 static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
 305 {
 306         count--;
 307         if (dmanr <= 3) {
 308                 dma_outb(count & 0xff,
 309                          ((dmanr & 3) << 1) + 1 + IO_DMA1_BASE);
 310                 dma_outb((count >> 8) & 0xff,
 311                          ((dmanr & 3) << 1) + 1 + IO_DMA1_BASE);
 312         } else {
 313                 dma_outb((count >> 1) & 0xff,
 314                          ((dmanr & 3) << 2) + 2 + IO_DMA2_BASE);
 315                 dma_outb((count >> 9) & 0xff,
 316                          ((dmanr & 3) << 2) + 2 + IO_DMA2_BASE);
 317         }
 318 }
 319
 320
 321 /* Get DMA residue count. After a DMA transfer, this
 322  * should return zero. Reading this while a DMA transfer is
 323  * still in progress will return unpredictable results.
 324  * If called before the channel has been used, it may return 1.
 325  * Otherwise, it returns the number of _bytes_ left to transfer.
 326  *
 327  * Assumes DMA flip-flop is clear.
 328  */
 329 static __inline__ int get_dma_residue(unsigned int dmanr)
 330 {
 331         unsigned int io_port = (dmanr <= 3)
 332             ? ((dmanr & 3) << 1) + 1 + IO_DMA1_BASE
 333             : ((dmanr & 3) << 2) + 2 + IO_DMA2_BASE;
 334
 335         /* using short to get 16-bit wrap around */
 336         unsigned short count;
 337
 338         count = 1 + dma_inb(io_port);
 339         count += dma_inb(io_port) << 8;
 340
 341         return (dmanr <= 3) ? count : (count << 1);
 342 }
 343
 344 /* These are in kernel/dma.c: */
 345
 346 /* reserve a DMA channel */
 347 extern int request_dma(unsigned int dmanr, const char *device_id);
 348 /* release it again */
 349 extern void free_dma(unsigned int dmanr);
 350
 351 #ifdef CONFIG_PCI
 352 extern int isa_dma_bridge_buggy;
 353 #else
 354 #define isa_dma_bridge_buggy    (0)
 355 #endif
 356
 357 #endif  /* !defined(CONFIG_PPC_ISERIES) || defined(CONFIG_PCI) */
 358
 359 #endif /* __KERNEL__ */
 360 #endif  /* _ASM_POWERPC_DMA_H */