include/linux/arcdevice.h

   1 /*
   2  * INET         An implementation of the TCP/IP protocol suite for the LINUX
   3  *              operating system.  NET  is implemented using the  BSD Socket
   4  *              interface as the means of communication with the user level.
   5  *
   6  *              Definitions used by the ARCnet driver.
   7  *
   8  * Authors:     Avery Pennarun and David Woodhouse
   9  *
  10  *              This program is free software; you can redistribute it and/or
  11  *              modify it under the terms of the GNU General Public License
  12  *              as published by the Free Software Foundation; either version
  13  *              2 of the License, or (at your option) any later version.
  14  *
  15  */
  16 #ifndef _LINUX_ARCDEVICE_H
  17 #define _LINUX_ARCDEVICE_H
  18
  19 #include <asm/timex.h>
  20 #include <linux/if_arcnet.h>
  21
  22 #ifdef __KERNEL__
  23
  24 #ifndef bool
  25 #define bool int
  26 #endif
  27
  28
  29 /*
  30  * RECON_THRESHOLD is the maximum number of RECON messages to receive
  31  * within one minute before printing a "cabling problem" warning. The
  32  * default value should be fine.
  33  *
  34  * After that, a "cabling restored" message will be printed on the next IRQ
  35  * if no RECON messages have been received for 10 seconds.
  36  *
  37  * Do not define RECON_THRESHOLD at all if you want to disable this feature.
  38  */
  39 #define RECON_THRESHOLD 30
  40
  41
  42 /*
  43  * Define this to the minimum "timeout" value.  If a transmit takes longer
  44  * than TX_TIMEOUT jiffies, Linux will abort the TX and retry.  On a large
  45  * network, or one with heavy network traffic, this timeout may need to be
  46  * increased.  The larger it is, though, the longer it will be between
  47  * necessary transmits - don't set this too high.
  48  */
  49 #define TX_TIMEOUT (HZ * 200 / 1000)
  50
  51
  52 /* Display warnings about the driver being an ALPHA version. */
  53 #undef ALPHA_WARNING
  54
  55
  56 /*
  57  * Debugging bitflags: each option can be enabled individually.
  58  *
  59  * Note: only debug flags included in the ARCNET_DEBUG_MAX define will
  60  *   actually be available.  GCC will (at least, GCC 2.7.0 will) notice
  61  *   lines using a BUGLVL not in ARCNET_DEBUG_MAX and automatically optimize
  62  *   them out.
  63  */
  64 #define D_NORMAL        1       /* important operational info             */
  65 #define D_EXTRA         2       /* useful, but non-vital information      */
  66 #define D_INIT          4       /* show init/probe messages               */
  67 #define D_INIT_REASONS  8       /* show reasons for discarding probes     */
  68 #define D_RECON         32      /* print a message whenever token is lost */
  69 #define D_PROTO         64      /* debug auto-protocol support            */
  70 /* debug levels below give LOTS of output during normal operation! */
  71 #define D_DURING        128     /* trace operations (including irq's)     */
  72 #define D_TX            256     /* show tx packets                        */
  73 #define D_RX            512     /* show rx packets                        */
  74 #define D_SKB           1024    /* show skb's                             */
  75 #define D_SKB_SIZE      2048    /* show skb sizes                         */
  76 #define D_TIMING        4096    /* show time needed to copy buffers to card */
  77
  78 #ifndef ARCNET_DEBUG_MAX
  79 #define ARCNET_DEBUG_MAX (127)  /* change to ~0 if you want detailed debugging */
  80 #endif
  81
  82 #ifndef ARCNET_DEBUG
  83 #define ARCNET_DEBUG (D_NORMAL|D_EXTRA)
  84 #endif
  85 extern int arcnet_debug;
  86
  87 /* macros to simplify debug checking */
  88 #define BUGLVL(x) if ((ARCNET_DEBUG_MAX)&arcnet_debug&(x))
  89 #define BUGMSG2(x,msg,args...) do { BUGLVL(x) printk(msg, ## args); } while (0)
  90 #define BUGMSG(x,msg,args...) \
  91         BUGMSG2(x, "%s%6s: " msg, \
  92             x==D_NORMAL ? KERN_WARNING \
  93                         : x < D_DURING ? KERN_INFO : KERN_DEBUG, \
  94             dev->name , ## args)
  95
  96 /* see how long a function call takes to run, expressed in CPU cycles */
  97 #define TIME(name, bytes, call) BUGLVL(D_TIMING) { \
  98             unsigned long _x, _y; \
  99             _x = get_cycles(); \
 100             call; \
 101             _y = get_cycles(); \
 102             BUGMSG(D_TIMING, \
 103                "%s: %d bytes in %lu cycles == " \
 104                "%lu Kbytes/100Mcycle\n",\
 105                    name, bytes, _y - _x, \
 106                    100000000 / 1024 * bytes / (_y - _x + 1));\
 107         } \
 108         else { \
 109                     call;\
 110         }
 111
 112
 113 /*
 114  * Time needed to reset the card - in ms (milliseconds).  This works on my
 115  * SMC PC100.  I can't find a reference that tells me just how long I
 116  * should wait.
 117  */
 118 #define RESETtime (300)
 119
 120 /*
 121  * These are the max/min lengths of packet payload, not including the
 122  * arc_hardware header, but definitely including the soft header.
 123  *
 124  * Note: packet sizes 254, 255, 256 are impossible because of the way
 125  * ARCnet registers work  That's why RFC1201 defines "exception" packets.
 126  * In non-RFC1201 protocols, we have to just tack some extra bytes on the
 127  * end.
 128  */
 129 #define MTU     253             /* normal packet max size */
 130 #define MinTU   257             /* extended packet min size */
 131 #define XMTU    508             /* extended packet max size */
 132
 133 /* status/interrupt mask bit fields */
 134 #define TXFREEflag      0x01    /* transmitter available */
 135 #define TXACKflag       0x02    /* transmitted msg. ackd */
 136 #define RECONflag       0x04    /* network reconfigured */
 137 #define TESTflag        0x08    /* test flag */
 138 #define RESETflag       0x10    /* power-on-reset */
 139 #define RES1flag        0x20    /* reserved - usually set by jumper */
 140 #define RES2flag        0x40    /* reserved - usually set by jumper */
 141 #define NORXflag        0x80    /* receiver inhibited */
 142
 143 /* Flags used for IO-mapped memory operations */
 144 #define AUTOINCflag     0x40    /* Increase location with each access */
 145 #define IOMAPflag       0x02    /* (for 90xx) Use IO mapped memory, not mmap */
 146 #define ENABLE16flag    0x80    /* (for 90xx) Enable 16-bit mode */
 147
 148 /* in the command register, the following bits have these meanings:
 149  *                0-2     command
 150  *                3-4     page number (for enable rcv/xmt command)
 151  *                 7      receive broadcasts
 152  */
 153 #define NOTXcmd         0x01    /* disable transmitter */
 154 #define NORXcmd         0x02    /* disable receiver */
 155 #define TXcmd           0x03    /* enable transmitter */
 156 #define RXcmd           0x04    /* enable receiver */
 157 #define CONFIGcmd       0x05    /* define configuration */
 158 #define CFLAGScmd       0x06    /* clear flags */
 159 #define TESTcmd         0x07    /* load test flags */
 160
 161 /* flags for "clear flags" command */
 162 #define RESETclear      0x08    /* power-on-reset */
 163 #define CONFIGclear     0x10    /* system reconfigured */
 164
 165 /* flags for "load test flags" command */
 166 #define TESTload        0x08    /* test flag (diagnostic) */
 167
 168 /* byte deposited into first address of buffers on reset */
 169 #define TESTvalue       0321    /* that's octal for 0xD1 :) */
 170
 171 /* for "enable receiver" command */
 172 #define RXbcasts        0x80    /* receive broadcasts */
 173
 174 /* flags for "define configuration" command */
 175 #define NORMALconf      0x00    /* 1-249 byte packets */
 176 #define EXTconf         0x08    /* 250-504 byte packets */
 177
 178 /* card feature flags, set during auto-detection.
 179  * (currently only used by com20020pci)
 180  */
 181 #define ARC_IS_5MBIT    1   /* card default speed is 5MBit */
 182 #define ARC_CAN_10MBIT  2   /* card uses COM20022, supporting 10MBit,
 183                                  but default is 2.5MBit. */
 184
 185
 186 /* information needed to define an encapsulation driver */
 187 struct ArcProto {
 188         char suffix;            /* a for RFC1201, e for ether-encap, etc. */
 189         int mtu;                /* largest possible packet */
 190
 191         void (*rx) (struct net_device * dev, int bufnum,
 192                     struct archdr * pkthdr, int length);
 193         int (*build_header) (struct sk_buff * skb, struct net_device *dev,
 194                              unsigned short ethproto, uint8_t daddr);
 195
 196         /* these functions return '1' if the skb can now be freed */
 197         int (*prepare_tx) (struct net_device * dev, struct archdr * pkt, int length,
 198                            int bufnum);
 199         int (*continue_tx) (struct net_device * dev, int bufnum);
 200 };
 201
 202 extern struct ArcProto *arc_proto_map[256], *arc_proto_default, *arc_bcast_proto;
 203 extern struct ArcProto arc_proto_null;
 204
 205
 206 /*
 207  * "Incoming" is information needed for each address that could be sending
 208  * to us.  Mostly for partially-received split packets.
 209  */
 210 struct Incoming {
 211         struct sk_buff *skb;    /* packet data buffer             */
 212         uint16_t sequence;      /* sequence number of assembly    */
 213         uint8_t lastpacket,     /* number of last packet (from 1) */
 214                 numpackets;     /* number of packets in split     */
 215 };
 216
 217
 218 /* only needed for RFC1201 */
 219 struct Outgoing {
 220         struct ArcProto *proto; /* protocol driver that owns this:
 221                                  *   if NULL, no packet is pending.
 222                                  */
 223         struct sk_buff *skb;    /* buffer from upper levels */
 224         struct archdr *pkt;     /* a pointer into the skb */
 225         uint16_t length,        /* bytes total */
 226                 dataleft,       /* bytes left */
 227                 segnum,         /* segment being sent */
 228                 numsegs;        /* number of segments */
 229 };
 230
 231
 232 struct arcnet_local {
 233         struct net_device_stats stats;
 234
 235         uint8_t config,         /* current value of CONFIG register */
 236                 timeout,        /* Extended timeout for COM20020 */
 237                 backplane,      /* Backplane flag for COM20020 */
 238                 clockp,         /* COM20020 clock divider */
 239                 clockm,         /* COM20020 clock multiplier flag */
 240                 setup,          /* Contents of setup1 register */
 241                 setup2,         /* Contents of setup2 register */
 242                 intmask;        /* current value of INTMASK register */
 243         uint8_t default_proto[256];     /* default encap to use for each host */
 244         int     cur_tx,         /* buffer used by current transmit, or -1 */
 245                 next_tx,        /* buffer where a packet is ready to send */
 246                 cur_rx;         /* current receive buffer */
 247         int     lastload_dest,  /* can last loaded packet be acked? */
 248                 lasttrans_dest; /* can last TX'd packet be acked? */
 249         int     timed_out;      /* need to process TX timeout and drop packet */
 250         unsigned long last_timeout;     /* time of last reported timeout */
 251         char *card_name;        /* card ident string */
 252         int card_flags;         /* special card features */
 253
 254         /*
 255          * Buffer management: an ARCnet card has 4 x 512-byte buffers, each of
 256          * which can be used for either sending or receiving.  The new dynamic
 257          * buffer management routines use a simple circular queue of available
 258          * buffers, and take them as they're needed.  This way, we simplify
 259          * situations in which we (for example) want to pre-load a transmit
 260          * buffer, or start receiving while we copy a received packet to
 261          * memory.
 262          *
 263          * The rules: only the interrupt handler is allowed to _add_ buffers to
 264          * the queue; thus, this doesn't require a lock.  Both the interrupt
 265          * handler and the transmit function will want to _remove_ buffers, so
 266          * we need to handle the situation where they try to do it at the same
 267          * time.
 268          *
 269          * If next_buf == first_free_buf, the queue is empty.  Since there are
 270          * only four possible buffers, the queue should never be full.
 271          */
 272         atomic_t buf_lock;
 273         int buf_queue[5];
 274         int next_buf, first_free_buf;
 275
 276         /* network "reconfiguration" handling */
 277         time_t first_recon,     /* time of "first" RECON message to count */
 278                 last_recon;     /* time of most recent RECON */
 279         int num_recons;         /* number of RECONs between first and last. */
 280         bool network_down;      /* do we think the network is down? */
 281
 282         struct {
 283                 uint16_t sequence;      /* sequence number (incs with each packet) */
 284                 uint16_t aborted_seq;
 285
 286                 struct Incoming incoming[256];  /* one from each address */
 287         } rfc1201;
 288
 289         /* really only used by rfc1201, but we'll pretend it's not */
 290         struct Outgoing outgoing;       /* packet currently being sent */
 291
 292         /* hardware-specific functions */
 293         struct {
 294                 struct module *owner;
 295                 void (*command) (struct net_device * dev, int cmd);
 296                 int (*status) (struct net_device * dev);
 297                 void (*intmask) (struct net_device * dev, int mask);
 298                 bool (*reset) (struct net_device * dev, bool really_reset);
 299                 void (*open) (struct net_device * dev);
 300                 void (*close) (struct net_device * dev);
 301
 302                 void (*copy_to_card) (struct net_device * dev, int bufnum, int offset,
 303                                       void *buf, int count);
 304                 void (*copy_from_card) (struct net_device * dev, int bufnum, int offset,
 305                                         void *buf, int count);
 306         } hw;
 307
 308         void *mem_start;        /* pointer to ioremap'ed MMIO */
 309 };
 310
 311
 312 #define ARCRESET(x)  (lp->hw.reset(dev, (x)))
 313 #define ACOMMAND(x)  (lp->hw.command(dev, (x)))
 314 #define ASTATUS()    (lp->hw.status(dev))
 315 #define AINTMASK(x)  (lp->hw.intmask(dev, (x)))
 316
 317
 318
 319 #if ARCNET_DEBUG_MAX & D_SKB
 320 void arcnet_dump_skb(struct net_device *dev, struct sk_buff *skb, char *desc);
 321 #else
 322 #define arcnet_dump_skb(dev,skb,desc) ;
 323 #endif
 324
 325 #if (ARCNET_DEBUG_MAX & D_RX) || (ARCNET_DEBUG_MAX & D_TX)
 326 void arcnet_dump_packet(struct net_device *dev, int bufnum, char *desc);
 327 #else
 328 #define arcnet_dump_packet(dev, bufnum, desc) ;
 329 #endif
 330
 331 void arcnet_unregister_proto(struct ArcProto *proto);
 332 irqreturn_t arcnet_interrupt(int irq, void *dev_id, struct pt_regs *regs);
 333 void arcdev_setup(struct net_device *dev);
 334 void arcnet_rx(struct net_device *dev, int bufnum);
 335
 336 #endif                          /* __KERNEL__ */
 337 #endif                          /* _LINUX_ARCDEVICE_H */