include/asm-arm/arch-at91/board.h

   1 /*
   2  * include/asm-arm/arch-at91/board.h
   3  *
   4  *  Copyright (C) 2005 HP Labs
   5  *
   6  * This program is free software; you can redistribute it and/or modify
   7  * it under the terms of the GNU General Public License as published by
   8  * the Free Software Foundation; either version 2 of the License, or
   9  * (at your option) any later version.
  10  *
  11  * This program is distributed in the hope that it will be useful,
  12  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  13  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  14  * GNU General Public License for more details.
  15  *
  16  * You should have received a copy of the GNU General Public License
  17  * along with this program; if not, write to the Free Software
  18  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  19  */
  20
  21 /*
  22  * These are data structures found in platform_device.dev.platform_data,
  23  * and describing board-specific data needed by drivers.  For example,
  24  * which pin is used for a given GPIO role.
  25  *
  26  * In 2.6, drivers should strongly avoid board-specific knowledge so
  27  * that supporting new boards normally won't require driver patches.
  28  * Most board-specific knowledge should be in arch/.../board-*.c files.
  29  */
  30
  31 #ifndef __ASM_ARCH_BOARD_H
  32 #define __ASM_ARCH_BOARD_H
  33
  34 #include <linux/mtd/partitions.h>
  35 #include <linux/device.h>
  36 #include <linux/i2c.h>
  37 #include <linux/leds.h>
  38 #include <linux/spi/spi.h>
  39
  40  /* USB Device */
  41 struct at91_udc_data {
  42         u8      vbus_pin;               /* high == host powering us */
  43         u8      pullup_pin;             /* active == D+ pulled up */
  44         u8      pullup_active_low;      /* true == pullup_pin is active low */
  45 };
  46 extern void __init at91_add_device_udc(struct at91_udc_data *data);
  47
  48  /* Compact Flash */
  49 struct at91_cf_data {
  50         u8      irq_pin;                /* I/O IRQ */
  51         u8      det_pin;                /* Card detect */
  52         u8      vcc_pin;                /* power switching */
  53         u8      rst_pin;                /* card reset */
  54         u8      chipselect;             /* EBI Chip Select number */
  55 };
  56 extern void __init at91_add_device_cf(struct at91_cf_data *data);
  57
  58  /* MMC / SD */
  59 struct at91_mmc_data {
  60         u8              det_pin;        /* card detect IRQ */
  61         unsigned        slot_b:1;       /* uses Slot B */
  62         unsigned        wire4:1;        /* (SD) supports DAT0..DAT3 */
  63         u8              wp_pin;         /* (SD) writeprotect detect */
  64         u8              vcc_pin;        /* power switching (high == on) */
  65 };
  66 extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data);
  67
  68  /* Ethernet (EMAC & MACB) */
  69 struct at91_eth_data {
  70         u32             phy_mask;
  71         u8              phy_irq_pin;    /* PHY IRQ */
  72         u8              is_rmii;        /* using RMII interface? */
  73 };
  74 extern void __init at91_add_device_eth(struct at91_eth_data *data);
  75
  76 #if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91CAP9)
  77 #define eth_platform_data       at91_eth_data
  78 #endif
  79
  80  /* USB Host */
  81 struct at91_usbh_data {
  82         u8              ports;          /* number of ports on root hub */
  83         u8              vbus_pin[];     /* port power-control pin */
  84 };
  85 extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
  86
  87  /* NAND / SmartMedia */
  88 struct at91_nand_data {
  89         u8              enable_pin;     /* chip enable */
  90         u8              det_pin;        /* card detect */
  91         u8              rdy_pin;        /* ready/busy */
  92         u8              ale;            /* address line number connected to ALE */
  93         u8              cle;            /* address line number connected to CLE */
  94         u8              bus_width_16;   /* buswidth is 16 bit */
  95         struct mtd_partition* (*partition_info)(int, int*);
  96 };
  97 extern void __init at91_add_device_nand(struct at91_nand_data *data);
  98
  99  /* I2C*/
 100 extern void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices);
 101
 102  /* SPI */
 103 extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices);
 104
 105  /* Serial */
 106 #define ATMEL_UART_CTS  0x01
 107 #define ATMEL_UART_RTS  0x02
 108 #define ATMEL_UART_DSR  0x04
 109 #define ATMEL_UART_DTR  0x08
 110 #define ATMEL_UART_DCD  0x10
 111 #define ATMEL_UART_RI   0x20
 112
 113 extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
 114 extern void __init at91_set_serial_console(unsigned portnr);
 115
 116 struct at91_uart_config {
 117         unsigned short  console_tty;    /* tty number of serial console */
 118         unsigned short  nr_tty;         /* number of serial tty's */
 119         short           tty_map[];      /* map UART to tty number */
 120 };
 121 extern struct platform_device *atmel_default_console_device;
 122 extern void __init __deprecated at91_init_serial(struct at91_uart_config *config);
 123
 124 struct atmel_uart_data {
 125         short           use_dma_tx;     /* use transmit DMA? */
 126         short           use_dma_rx;     /* use receive DMA? */
 127         void __iomem    *regs;          /* virtual base address, if any */
 128 };
 129 extern void __init at91_add_device_serial(void);
 130
 131 /*
 132  * SSC -- accessed through ssc_request(id).  Drivers don't bind to SSC
 133  * platform devices.  Their SSC ID is part of their configuration data,
 134  * along with information about which SSC signals they should use.
 135  */
 136 #define ATMEL_SSC_TK    0x01
 137 #define ATMEL_SSC_TF    0x02
 138 #define ATMEL_SSC_TD    0x04
 139 #define ATMEL_SSC_TX    (ATMEL_SSC_TK | ATMEL_SSC_TF | ATMEL_SSC_TD)
 140
 141 #define ATMEL_SSC_RK    0x10
 142 #define ATMEL_SSC_RF    0x20
 143 #define ATMEL_SSC_RD    0x40
 144 #define ATMEL_SSC_RX    (ATMEL_SSC_RK | ATMEL_SSC_RF | ATMEL_SSC_RD)
 145
 146 extern void __init at91_add_device_ssc(unsigned id, unsigned pins);
 147
 148  /* LCD Controller */
 149 struct atmel_lcdfb_info;
 150 extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
 151
 152  /* AC97 */
 153 struct atmel_ac97_data {
 154         u8              reset_pin;      /* reset */
 155 };
 156 extern void __init at91_add_device_ac97(struct atmel_ac97_data *data);
 157
 158  /* ISI */
 159 extern void __init at91_add_device_isi(void);
 160
 161  /* LEDs */
 162 extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
 163 extern void __init at91_gpio_leds(struct gpio_led *leds, int nr);
 164
 165 /* FIXME: this needs a better location, but gets stuff building again */
 166 extern int at91_suspend_entering_slow_clock(void);
 167
 168 #endif