linprocfs - Introduce /proc/mounts

[dragonfly.git] / sys / platform / pc32 / isa / ic / mb86960.h

/*
 * All Rights Reserved, Copyright (C) Fujitsu Limited 1995
 *
 * This software may be used, modified, copied, distributed, and sold, in
 * both source and binary form provided that the above copyright, these
 * terms and the following disclaimer are retained.  The name of the author
 * and/or the contributor may not be used to endorse or promote products
 * derived from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND THE CONTRIBUTOR ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR OR THE CONTRIBUTOR BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 *
 * $FreeBSD: src/sys/i386/isa/ic/mb86960.h,v 1.2.8.1 2000/08/03 01:01:25 peter Exp $
 * $DragonFly: src/sys/platform/pc32/isa/ic/mb86960.h,v 1.2 2003/06/17 04:28:37 dillon Exp $
 */

/*
 * Registers of Fujitsu MB86960A/MB86965A series Ethernet controllers.
 * Written and contributed by M.S. <seki@sysrap.cs.fujitsu.co.jp>
 */

/*
 * Notes on register naming:
 *
 * Fujitsu documents for MB86960A/MB86965A uses no mnemorable names
 * for their registers.  They defined only three names for 32
 * registers and appended numbers to distinguish registers of
 * same name.  Surprisingly, the numbers represent I/O address
 * offsets of the registers from the base addresses, and their
 * names correspond to the "bank" the registers are allocated.
 * All this means that, for example, to say "read DLCR8" has no more
 * than to say "read a register at offset 8 on bank DLCR."
 *
 * The following definitions may look silly, but that's what Fujitsu
 * did, and it is necessary to know these names to read Fujitsu
 * documents..
 */

/* Data Link Control Registrs, on invaliant port addresses.  */
#define FE_DLCR0        0
#define FE_DLCR1        1
#define FE_DLCR2        2
#define FE_DLCR3        3
#define FE_DLCR4        4
#define FE_DLCR5        5
#define FE_DLCR6        6
#define FE_DLCR7        7

/* More DLCRs, on register bank #0.  */
#define FE_DLCR8        8
#define FE_DLCR9        9
#define FE_DLCR10       10
#define FE_DLCR11       11
#define FE_DLCR12       12
#define FE_DLCR13       13
#define FE_DLCR14       14
#define FE_DLCR15       15

/* Malticast Address Registers.  On register bank #1.  */
#define FE_MAR8         8
#define FE_MAR9         9
#define FE_MAR10        10
#define FE_MAR11        11
#define FE_MAR12        12
#define FE_MAR13        13
#define FE_MAR14        14
#define FE_MAR15        15

/* Buffer Memory Port Registers.  On register back #2.  */
#define FE_BMPR8        8
#define FE_BMPR9        9
#define FE_BMPR10       10
#define FE_BMPR11       11
#define FE_BMPR12       12
#define FE_BMPR13       13
#define FE_BMPR14       14
#define FE_BMPR15       15

/* More BMPRs, only on 86965, accessible only when JLI mode.  */
#define FE_BMPR16       16
#define FE_BMPR17       17
#define FE_BMPR18       18
#define FE_BMPR19       19

/*
 * Definitions of registers.
 * I don't have Fujitsu documents of MB86960A/MB86965A, so I don't
 * know the official names for each flags and fields.  The following
 * names are assigned by me (the author of this file,) since I cannot
 * mnemorize hexadecimal constants for all of these functions.
 * Comments?
 *
 * I've got documents from Fujitsu web site, recently.  However, it's
 * too late.  Names for some fields (bits) are kept different from
 * those used in the Fujitsu documents...
 */

/* DLCR0 -- transmitter status */
#define FE_D0_BUSERR    0x01    /* Bus write error?                     */
#define FE_D0_COLL16    0x02    /* Collision limit (16) encountered     */
#define FE_D0_COLLID    0x04    /* Collision on last transmission       */
#define FE_D0_JABBER    0x08    /* Jabber                               */
#define FE_D0_CRLOST    0x10    /* Carrier lost on last transmission    */
#define FE_D0_PKTRCD    0x20    /* Last packet looped back correctly    */
#define FE_D0_NETBSY    0x40    /* Network Busy (Carrier Detected)      */
#define FE_D0_TXDONE    0x80    /* Transmission complete                */

/* DLCR1 -- receiver status */
#define FE_D1_OVRFLO    0x01    /* Receiver buffer overflow             */
#define FE_D1_CRCERR    0x02    /* CRC error on last packet             */
#define FE_D1_ALGERR    0x04    /* Alignment error on last packet       */
#define FE_D1_SRTPKT    0x08    /* Short (RUNT) packet is received      */
#define FE_D1_RMTRST    0x10    /* Remote reset packet (type = 0x0900)  */
#define FE_D1_DMAEOP    0x20    /* Host asserted End of DMA OPeration   */
#define FE_D1_BUSERR    0x40    /* Bus read error                       */
#define FE_D1_PKTRDY    0x80    /* Packet(s) ready on receive buffer    */

/* DLCR2 -- transmitter interrupt control; same layout as DLCR0 */
#define FE_D2_BUSERR    FE_D0_BUSERR
#define FE_D2_COLL16    FE_D0_COLL16
#define FE_D2_COLLID    FE_D0_COLLID
#define FE_D2_JABBER    FE_D0_JABBER
#define FE_D2_TXDONE    FE_D0_TXDONE

#define FE_D2_RESERVED  0x70

/* DLCR3 -- receiver interrupt control; same layout as DLCR1 */
#define FE_D3_OVRFLO    FE_D1_OVRFLO
#define FE_D3_CRCERR    FE_D1_CRCERR
#define FE_D3_ALGERR    FE_D1_ALGERR
#define FE_D3_SRTPKT    FE_D1_SRTPKT
#define FE_D3_RMTRST    FE_D1_RMTRST
#define FE_D3_DMAEOP    FE_D1_DMAEOP
#define FE_D3_BUSERR    FE_D1_BUSERR
#define FE_D3_PKTRDY    FE_D1_PKTRDY

/* DLCR4 -- transmitter operation mode */
#define FE_D4_DSC       0x01    /* Disable carrier sense on trans.      */
#define FE_D4_LBC       0x02    /* Loop back test control               */
#define FE_D4_CNTRL     0x04    /* - tied to CNTRL pin of the chip      */
#define FE_D4_TEST1     0x08    /* Test output #1                       */
#define FE_D4_COL       0xF0    /* Collision counter                    */

#define FE_D4_LBC_ENABLE        0x00    /* Perform loop back test       */
#define FE_D4_LBC_DISABLE       0x02    /* Normal operation             */

#define FE_D4_COL_SHIFT 4

/* DLCR5 -- receiver operation mode */
#define FE_D5_AFM0      0x01    /* Receive packets for other stations   */
#define FE_D5_AFM1      0x02    /* Receive packets for this station     */
#define FE_D5_RMTRST    0x04    /* Enable remote reset operation        */
#define FE_D5_SRTPKT    0x08    /* Accept short (RUNT) packets          */
#define FE_D5_SRTADR    0x10    /* Short (16 bits?) MAC address         */
#define FE_D5_BADPKT    0x20    /* Accept packets with error            */
#define FE_D5_BUFEMP    0x40    /* Receive buffer is empty              */
#define FE_D5_TEST2     0x80    /* Test output #2                       */

/* DLCR6 -- hardware configuration #0 */
#define FE_D6_BUFSIZ    0x03    /* Size of NIC buffer SRAM              */
#define FE_D6_TXBSIZ    0x0C    /* Size (and config)of trans. buffer    */
#define FE_D6_BBW       0x10    /* Buffer SRAM bus width                */
#define FE_D6_SBW       0x20    /* System bus width                     */
#define FE_D6_SRAM      0x40    /* Buffer SRAM access time              */
#define FE_D6_DLC       0x80    /* Disable DLC (recever/transmitter)    */

#define FE_D6_BUFSIZ_8KB        0x00    /* The board has  8KB SRAM      */
#define FE_D6_BUFSIZ_16KB       0x01    /* The board has 16KB SRAM      */
#define FE_D6_BUFSIZ_32KB       0x02    /* The board has 32KB SRAM      */
#define FE_D6_BUFSIZ_64KB       0x03    /* The board has 64KB SRAM      */

#define FE_D6_TXBSIZ_1x2KB      0x00    /* Single 2KB buffer for trans. */
#define FE_D6_TXBSIZ_2x2KB      0x04    /* Double 2KB buffers           */
#define FE_D6_TXBSIZ_2x4KB      0x08    /* Double 4KB buffers           */
#define FE_D6_TXBSIZ_2x8KB      0x0C    /* Double 8KB buffers           */

#define FE_D6_BBW_WORD          0x00    /* SRAM has 16 bit data line    */
#define FE_D6_BBW_BYTE          0x10    /* SRAM has  8 bit data line    */

#define FE_D6_SBW_WORD          0x00    /* Access with 16 bit (AT) bus  */
#define FE_D6_SBW_BYTE          0x20    /* Access with  8 bit (XT) bus  */

#define FE_D6_SRAM_150ns        0x00    /* The board has slow SRAM      */
#define FE_D6_SRAM_100ns        0x40    /* The board has fast SRAM      */

#define FE_D6_DLC_ENABLE        0x00    /* Normal operation             */
#define FE_D6_DLC_DISABLE       0x80    /* Stop sending/receiving       */

/* DLC7 -- hardware configuration #1 */
#define FE_D7_BYTSWP    0x01    /* Host byte order control              */
#define FE_D7_EOPPOL    0x02    /* Polarity of DMA EOP signal           */
#define FE_D7_RBS       0x0C    /* Register bank select                 */
#define FE_D7_RDYPNS    0x10    /* Senses RDYPNSEL input signal         */
#define FE_D7_POWER     0x20    /* Stand-by (power down) mode control   */
#define FE_D7_IDENT     0xC0    /* Chip identification                  */

#define FE_D7_BYTSWP_LH 0x00    /* DEC/Intel byte order         */
#define FE_D7_BYTSWP_HL 0x01    /* IBM/Motorolla byte order     */

#define FE_D7_RBS_DLCR          0x00    /* Select DLCR8-15              */
#define FE_D7_RBS_MAR           0x04    /* Select MAR8-15               */
#define FE_D7_RBS_BMPR          0x08    /* Select BMPR8-15              */

#define FE_D7_POWER_DOWN        0x00    /* Power down (stand-by) mode   */
#define FE_D7_POWER_UP          0x20    /* Normal operation             */

#define FE_D7_IDENT_TDK         0x00    /* TDK chips?                   */
#define FE_D7_IDENT_NICE        0x80    /* Fujitsu NICE (86960)         */
#define FE_D7_IDENT_EC          0xC0    /* Fujitsu EtherCoupler (86965) */

/* DLCR8 thru DLCR13 are for Ethernet station address.  */

/* DLCR14 and DLCR15 are for TDR.  (TDR is used for cable diagnostic.)  */

/* MAR8 thru MAR15 are for Multicast address filter.  */

/* BMPR8 and BMPR9 are for packet data.  */

/* BMPR10 -- transmitter start trigger */
#define FE_B10_START    0x80    /* Start transmitter                    */
#define FE_B10_COUNT    0x7F    /* Packet count                         */

/* BMPR11 -- 16 collisions control */
#define FE_B11_CTRL     0x01    /* Skip or resend errored packets       */
#define FE_B11_MODE1    0x02    /* Restart transmitter after COLL16     */
#define FE_B11_MODE2    0x04    /* Automatic restart enable             */

#define FE_B11_CTRL_RESEND      0x00    /* Re-send the collided packet  */
#define FE_B11_CTRL_SKIP        0x01    /* Skip the collided packet     */

/* BMPR12 -- DMA enable */
#define FE_B12_TXDMA    0x01    /* Enable transmitter DMA               */
#define FE_B12_RXDMA    0x02    /* Enable receiver DMA                  */

/* BMPR13 -- DMA control */
#define FE_B13_BSTCTL   0x03    /* DMA burst mode control               */
#define FE_B13_TPTYPE   0x04    /* Twisted pair cable impedance         */
#define FE_B13_PORT     0x18    /* Port (TP/AUI) selection              */
#define FE_B13_LNKTST   0x20    /* Link test enable                     */
#define FE_B13_SQTHLD   0x40    /* Lower squelch threshold              */
#define FE_B13_IOUNLK   0x80    /* Change I/O base address, on JLI mode */

#define FE_B13_BSTCTL_1         0x00
#define FE_B13_BSTCTL_4         0x01
#define FE_B13_BSTCTL_8         0x02
#define FE_B13_BSTCLT_12        0x03

#define FE_B13_TPTYPE_UTP       0x00    /* Unshielded (standard) cable  */
#define FE_B13_TPTYPE_STP       0x04    /* Shielded (IBM) cable         */

#define FE_B13_PORT_AUTO        0x00    /* Auto detected                */
#define FE_B13_PORT_TP          0x08    /* Force TP                     */
#define FE_B13_PORT_AUI         0x18    /* Force AUI                    */

/* BMPR14 -- More receiver control and more transmission interrupts */
#define FE_B14_FILTER   0x01    /* Filter out self-originated packets   */
#define FE_B14_SQE      0x02    /* SQE interrupt enable                 */
#define FE_B14_SKIP     0x04    /* Skip a received packet               */
#define FE_B14_RJAB     0x20    /* RJAB interrupt enable                */
#define FE_B14_LLD      0x40    /* Local-link-down interrupt enable     */
#define FE_B14_RLD      0x80    /* Remote-link-down interrupt enable    */

/* BMPR15 -- More transmitter status; basically same layout as BMPR14 */
#define FE_B15_SQE      FE_B14_SQE
#define FE_B15_RCVPOL   0x08    /* Reversed receive line polarity       */
#define FE_B15_RMTPRT   0x10    /* ???                                  */
#define FE_B15_RAJB     FE_B14_RJAB
#define FE_B15_LLD      FE_B14_LLD
#define FE_B15_RLD      FE_B14_RLD

/* BMPR16 -- EEPROM control */
#define FE_B16_DOUT     0x04    /* EEPROM Data in (CPU to EEPROM)       */
#define FE_B16_SELECT   0x20    /* EEPROM chip select                   */
#define FE_B16_CLOCK    0x40    /* EEPROM shift clock                   */
#define FE_B16_DIN      0x80    /* EEPROM data out (EEPROM to CPU)      */

/* BMPR17 -- EEPROM data */
#define FE_B17_DATA     0x80    /* EEPROM data bit                      */

/* BMPR18 -- cycle I/O address setting in JLI mode */

/* BMPR19 -- ISA interface configuration in JLI mode */
#define FE_B19_IRQ              0xC0
#define FE_B19_IRQ_SHIFT        6

#define FE_B19_ROM              0x38
#define FE_B19_ROM_SHIFT        3

#define FE_B19_ADDR             0x07
#define FE_B19_ADDR_SHIFT       0

/*
 * An extra I/O port address to reset 86965.  This location is called
 * "ID ROM area" by Fujitsu document.
 */

/*
 * Flags in Receive Packet Header... Basically same layout as DLCR1.
 */
#define FE_RPH_OVRFLO   FE_D1_OVRFLO
#define FE_RPH_CRCERR   FE_D1_CRCERR
#define FE_RPH_ALGERR   FE_D1_ALGERR
#define FE_RPH_SRTPKT   FE_D1_SRTPKT
#define FE_RPH_RMTRST   FE_D1_RMTRST
#define FE_RPH_GOOD     0x20    /* Good packet follows                  */

/*
 * EEPROM specification (of JLI mode).
 */

/* Number of bytes in an EEPROM accessible through 86965.  */
#define FE_EEPROM_SIZE  32

/* Offset for JLI config; automatically copied into BMPR19 at startup.  */
#define FE_EEPROM_CONF  0

/*
 * Some 8696x specific constants.
 */

/* Length (in bytes) of a Multicast Address Filter.  */
#define FE_FILTER_LEN   8

/* How many packets we can put in the transmission buffer on NIC memory.  */
#define FE_QUEUEING_MAX 127

/* Length (in bytes) of a "packet length" word in transmission buffer.  */
#define FE_DATA_LEN_LEN 2

/* Special Multicast Address Filter value.  */
#define FE_FILTER_NOTHING       { 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00 }
#define FE_FILTER_ALL           { 0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF }