syscons - Add option for the default terminal border color to kernel config.
[dragonfly.git] / sys / config / LINT64
blob93aa5c4be9c416d9a63b1f2f17e3b7c8b16605db
2 # X86_64_LINT -- config file for checking all the sources, tries to pull in
3 #       as much of the source tree as it can.
5 # $FreeBSD: src/sys/i386/conf/LINT,v 1.749.2.144 2003/06/04 17:56:59 sam Exp $
7 # See the kernconf(5) manual page for more information on the format of
8 # this file.
10 # NB: You probably don't want to try running a kernel built from this
11 # file.  Instead, you should start from X86_64_GENERIC, and add options
12 # from this file as required.
15 # These directives are mandatory.  The machine directive specifies the
16 # platform and the machine_arch directive specifies the cpu architecture.
18 platform        pc64
19 machine         x86_64
20 machine_arch    x86_64
23 # This is the ``identification'' of the kernel.  Usually this should
24 # be the same as the name of your kernel.
26 ident           X86_64_LINT
29 # The `maxusers' parameter controls the static sizing of a number of
30 # internal system tables by a formula defined in subr_param.c.  Setting
31 # maxusers to 0 will cause the system to auto-size based on physical
32 # memory.
34 maxusers        10
37 # The `makeoptions' parameter allows variables to be passed to the
38 # generated Makefile in the build area.
40 # CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
41 # after most other flags.  Here we use it to inhibit use of non-optimal
42 # gcc builtin functions (e.g., memcmp).
44 # DEBUG happens to be magic.
45 # The following is equivalent to 'config -g KERNELNAME' and creates
46 # 'kernel.debug' compiled with -g debugging as well as a normal
47 # 'kernel'.  Use 'make install.debug' to install the debug kernel
48 # but that isn't normally necessary as the debug symbols are not loaded
49 # by the kernel and are not useful there anyway.
51 # KERNEL can be overridden so that you can change the default name of your
52 # kernel.
54 # MODULES_OVERRIDE can be used to limit modules built to a specific list.
56 # INSTALLSTRIPPED can be set to cause installkernel to install stripped
57 # kernels and modules rather than a kernel and modules with debug symbols.
59 # INSTALLSTRIPPEDMODULES can be set to allow a full debug kernel to be
60 # installed, but to strip the installed modules.
62 makeoptions     CONF_CFLAGS=-fno-builtin  #Don't allow use of memcmp, etc.
63 #makeoptions    DEBUG=-g                #Build kernel with gdb(1) debug symbols
64 #makeoptions    KERNEL=foo              #Build kernel "foo" and install "/foo"
65 # Only build those parts of the sound system I need.
66 #makeoptions    MODULES_OVERRIDE="sound/snd sound/pcm"
67 #makeoptions    INSTALLSTRIPPED=1
68 #makeoptions    INSTALLSTRIPPEDMODULES=1
71 # Certain applications can grow to be larger than the 128M limit
72 # that DragonFly initially imposes.  Below are some options to
73 # allow that limit to grow to 256MB, and can be increased further
74 # with changing the parameters.  MAXDSIZ is the maximum that the
75 # limit can be set to, and the DFLDSIZ is the default value for
76 # the limit.  MAXSSIZ is the maximum that the stack limit can be
77 # set to.  You might want to set the default lower than the max,
78 # and explicitly set the maximum with a shell command for processes
79 # that regularly exceed the limit like INND.
81 options         MAXDSIZ="(256*1024*1024)"
82 options         MAXSSIZ="(256*1024*1024)"
83 options         DFLDSIZ="(256*1024*1024)"
86 # BLKDEV_IOSIZE sets the default block size used in user block
87 # device I/O.  Note that this value will be overridden by the label
88 # when specifying a block device from a label with a non-0
89 # partition blocksize.  The default is PAGE_SIZE.
91 options         BLKDEV_IOSIZE=8192
93 # This allows you to actually store this configuration file into
94 # the kernel binary itself, where it may be later read by saying:
95 #    strings -n 3 /kernel | sed -n 's/^___//p' > MYKERNEL
97 options         INCLUDE_CONFIG_FILE     # Include this file in kernel
100 # The root device and filesystem type can be compiled in;
101 # this provides a fallback option if the root device cannot
102 # be correctly guessed by the bootstrap code, or an override if
103 # the RB_DFLTROOT flag (-r) is specified when booting the kernel.
105 options         ROOTDEVNAME=\"ufs:da0s2e\"
107 #####################################################################
108 # CPU OPTIONS
110 cpu             HAMMER_CPU
113 # Options for CPU features.
115 # CPU_DISABLE_AVX disables AVX instruction set.
117 options         CPU_DISABLE_AVX
119 #####################################################################
120 # COMPATIBILITY OPTIONS
122 # Enable NDIS binary driver support
123 options         NDISAPI
124 device          ndis
127 # These three options provide support for System V Interface
128 # Definition-style interprocess communication, in the form of shared
129 # memory, semaphores, and message queues, respectively.
131 # System V shared memory and tunable parameters
132 options         SHMMIN=2        # min shared memory segment size (bytes)
133 options         SHMMNI=33       # max number of shared memory identifiers
134 options         SHMSEG=9        # max shared memory segments per process
136 # System V semaphores and tunable parameters
137 options         SEMMAP=31       # amount of entries in semaphore map
138 options         SEMMNI=11       # number of semaphore identifiers in the system
139 options         SEMMNS=61       # number of semaphores in the system
140 options         SEMMNU=31       # number of undo structures in the system
141 options         SEMMSL=61       # max number of semaphores per id
142 options         SEMOPM=101      # max number of operations per semop call
143 options         SEMUME=11       # max number of undo entries per process
145 # System V message queues and tunable parameters
146 options         MSGMNB=2049     # max characters per message queue
147 options         MSGMNI=41       # max number of message queue identifiers
148 options         MSGSEG=2049     # max number of message segments in the system
149 options         MSGSSZ=16       # size of a message segment MUST be power of 2
150 options         MSGTQL=41       # max amount of messages in the system
152 #####################################################################
153 # DEBUGGING OPTIONS
156 # Enable the kernel debugger.
158 options         DDB
161 # Print a stack trace on kernel panic.
163 options         DDB_TRACE
166 # Don't drop into DDB for a panic. Intended for unattended operation
167 # where you may want to drop to DDB from the console, but still want
168 # the machine to recover from a panic
170 options         DDB_UNATTENDED
173 # If using GDB remote mode to debug the kernel, there's a non-standard
174 # extension to the remote protocol that can be used to use the serial
175 # port as both the debugging port and the system console.  It's non-
176 # standard and you're on your own if you enable it.  See also the
177 # "remotechat" variables in the DragonFly specific version of gdb.
179 options         GDB_REMOTE_CHAT
182 # KTRACE enables the system-call tracing facility ktrace(2).
184 options         KTRACE                  #kernel tracing
187 # The INVARIANTS option is used in a number of source files to enable
188 # extra sanity checking of internal structures.  This support is not
189 # enabled by default because of the extra time it would take to check
190 # for these conditions, which can only occur as a result of
191 # programming errors.
193 options         INVARIANTS
196 # The DIAGNOSTIC option is used to enable extra debugging information
197 # from some parts of the kernel.  As this makes everything more noisy,
198 # it is disabled by default.
200 options         DIAGNOSTIC
203 # This option let some drivers co-exist that can't co-exist in a running
204 # system.  This is used to be able to compile all kernel code in one go for
205 # quality assurance purposes (like this file, which the option takes it name
206 # from.)
208 options         COMPILING_LINT
211 # XXX - this doesn't belong here.
212 # Allow ordinary users to take the console - this is useful for X.
213 options         UCONSOLE
215 #####################################################################
216 # NETWORKING OPTIONS
219 # Protocol families:
220 #  Only the INET (Internet) family is officially supported in DragonFly.
221 #  Source code for the NS (Xerox Network Service) is provided for amusement
222 #  value.
224 options         INET                    #Internet communications protocols
225 options         INET6                   #IPv6 communications protocols
226 options         IPSEC                   #IP security
227 options         IPSEC_ESP               #IP security (crypto; define w/ IPSEC)
228 options         IPSEC_DEBUG             #debug for IP security
230 # Set IPSEC_FILTERGIF to force packets coming through a gif tunnel
231 # to be processed by any configured packet filtering (ipfw).
232 # The default is that packets coming from a tunnel are _not_ processed;
233 # they are assumed trusted.
235 # Note that enabling this can be problematic as there are no mechanisms
236 # in place for distinguishing packets coming out of a tunnel (e.g. no
237 # encX devices as found on openbsd).
239 #options        IPSEC_FILTERGIF         #filter ipsec packets from a tunnel
242 # Experimental IPsec implementation that uses the kernel crypto
243 # framework.  This cannot be configured together with IPSEC and
244 # (currently) supports only IPv4.  To use this you must also
245 # configure the crypto device (see below).  Note that with this
246 # you get all the IPsec protocols (e.g. there is no FAST_IPSEC_ESP).
247 # IPSEC_DEBUG is used, as above, to configure debugging support
248 # within the IPsec protocols.
250 #options        FAST_IPSEC              #new IPsec
252 options         MPLS                    #Multi-Protocol Label Switching
255 # SMB/CIFS requester
256 # NETSMB enables support for SMB protocol, it requires LIBMCHAIN and LIBICONV
257 # options.
258 # NETSMBCRYPTO enables support for encrypted passwords.
259 options         NETSMB                  #SMB/CIFS requester
260 options         NETSMBCRYPTO            #encrypted password support for SMB
262 # mchain library. It can be either loaded as KLD or compiled into kernel
263 options         LIBMCHAIN               #mbuf management library
265 # netgraph(4). Enable the base netgraph code with the NETGRAPH option.
266 # Individual node types can be enabled with the corresponding option
267 # listed below; however, this is not strictly necessary as netgraph
268 # will automatically load the corresponding KLD module if the node type
269 # is not already compiled into the kernel. Each type below has a
270 # corresponding man page, e.g., ng_async(4).
271 options         NETGRAPH                #netgraph(4) system
272 options         NETGRAPH_ASYNC
273 options         NETGRAPH_BPF
274 options         NETGRAPH_BRIDGE
275 options         NETGRAPH_CISCO
276 options         NETGRAPH_ECHO
277 options         NETGRAPH_EIFACE
278 options         NETGRAPH_ETHER
279 options         NETGRAPH_FEC
280 options         NETGRAPH_FRAME_RELAY
281 options         NETGRAPH_HOLE
282 options         NETGRAPH_IFACE
283 options         NETGRAPH_KSOCKET
284 options         NETGRAPH_L2TP
285 options         NETGRAPH_LMI
286 # MPPC compression requires proprietary files (not included)
287 #options        NETGRAPH_MPPC_COMPRESSION
288 options         NETGRAPH_MPPC_ENCRYPTION
289 options         NETGRAPH_ONE2MANY
290 options         NETGRAPH_PPP
291 options         NETGRAPH_PPPOE
292 options         NETGRAPH_PPTPGRE
293 options         NETGRAPH_RFC1490
294 options         NETGRAPH_SOCKET
295 options         NETGRAPH_TEE
296 options         NETGRAPH_TTY
297 options         NETGRAPH_UI
298 options         NETGRAPH_VJC
300 device          mn      # Munich32x/Falc54 Nx64kbit/sec cards.
303 # Network interfaces:
304 #  The `loop' pseudo-device is MANDATORY when networking is enabled.
305 #  The `ether' pseudo-device provides generic code to handle
306 #  Ethernets; it is MANDATORY when a Ethernet device driver is
307 #  configured.
308 #  The `sppp' pseudo-device serves a similar role for certain types
309 #  of synchronous PPP links.
310 #  The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
311 #  The `ppp' pseudo-device implements the Point-to-Point Protocol.
312 #  The `bpf' pseudo-device enables the Berkeley Packet Filter.  Be
313 #  aware of the legal and administrative consequences of enabling this
314 #  option.  The number of devices determines the maximum number of
315 #  simultaneous BPF clients programs runnable.
316 #  The `disc' pseudo-device implements a minimal network interface,
317 #  which throws away all packets sent and never receives any.  It is
318 #  included for testing purposes.  This shows up as the 'ds' interface.
319 #  The `tun' pseudo-device implements (user-)ppp and nos-tun
320 #  The `gif' pseudo-device implements IPv6 over IP4 tunneling,
321 #  IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
322 #  IPv6 over IPv6 tunneling.
323 #  The `gre' device implements two types of IP4 over IP4 tunneling:
324 #  GRE and MOBILE, as specified in the RFC1701 and RFC2004.
325 #  The `faith' pseudo-device captures packets sent to it and diverts them
326 #  to the IPv4/IPv6 translation daemon.
327 #  The `stf' device implements 6to4 encapsulation.
328 #  The `ef' pseudo-device provides support for multiple ethernet frame types
329 #  specified via ETHER_* options. See ef(4) for details.
331 # The PPP_BSDCOMP option enables support for compress(1) style entire
332 # packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
333 # PPP_FILTER enables code for filtering the ppp data stream and selecting
334 # events for resetting the demand dial activity timer - requires bpf.
335 # See pppd(8) for more details.
337 pseudo-device   ether                   #Generic Ethernet
338 pseudo-device   vlan    1               #VLAN support
339 pseudo-device   bridge                  #Bridging support
340 pseudo-device   sppp                    #Generic Synchronous PPP
341 pseudo-device   loop                    #Network loopback device
342 pseudo-device   bpf                     #Berkeley packet filter
343 pseudo-device   disc                    #Discard device (ds0, ds1, etc)
344 pseudo-device   tap                     #Ethernet tunnel network interface
345 pseudo-device   tun                     #Tunnel driver (ppp(8), nos-tun(8))
346 pseudo-device   sl      2               #Serial Line IP
347 pseudo-device   gre                     #IP over IP tunneling
348 pseudo-device   ppp     2               #Point-to-point protocol
349 options         PPP_BSDCOMP             #PPP BSD-compress support
350 options         PPP_DEFLATE             #PPP zlib/deflate/gzip support
351 options         PPP_FILTER              #enable bpf filtering (needs bpf)
353 # for IPv6
354 pseudo-device   gif                     #IPv6 and IPv4 tunneling
355 pseudo-device   faith   1               #for IPv6 and IPv4 translation
356 pseudo-device   stf                     #6to4 IPv6 over IPv4 encapsulation
359 # Internet family options:
361 # MROUTING enables the kernel multicast packet forwarder, which works
362 # with mrouted(8).
364 # PIM enables Protocol Independent Multicast in the kernel.
365 # Requires MROUTING enabled.
367 # IPFIREWALL enables support for IP firewall construction, in
368 # conjunction with the `ipfw' program.  IPFIREWALL_VERBOSE sends
369 # logged packets to the system logger.  IPFIREWALL_VERBOSE_LIMIT
370 # limits the number of times a matching entry can be logged.
372 # WARNING:  IPFIREWALL defaults to a policy of "deny ip from any to any"
373 # and if you do not add other rules during startup to allow access,
374 # YOU WILL LOCK YOURSELF OUT.  It is suggested that you set firewall_type=open
375 # in /etc/rc.conf when first enabling this feature, then refining the
376 # firewall rules in /etc/rc.firewall after you've tested that the new kernel
377 # feature works properly.
379 # IPFIREWALL3 is based on a newer version of FreeBSD's ipfw2, along with
380 # some enhancements. See ipfw3(4).
382 # IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
383 # allow everything.  Use with care, if a cracker can crash your
384 # firewall machine, they can get to your protected machines.  However,
385 # if you are using it as an as-needed filter for specific problems as
386 # they arise, then this may be for you.  Changing the default to 'allow'
387 # means that you won't get stuck if the kernel and /sbin/ipfw binary get
388 # out of sync.
390 # IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
392 # IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
393 # packets without touching the ttl).  This can be useful to hide firewalls
394 # from traceroute and similar tools.
396 # TCPDEBUG is undocumented.
398 # ICMPPRINTFS enables ICMP to do extra debug prints.
400 options         MROUTING                # Multicast routing
401 options         PIM                     # Protocol Independent Multicast
402 options         IPFIREWALL              #firewall
403 options         IPFIREWALL_DEBUG        #debug prints
404 options         IPFIREWALL_VERBOSE      #enable logging to syslogd(8)
405 options         IPFIREWALL_VERBOSE_LIMIT=100    #limit verbosity
406 options         IPFIREWALL_DEFAULT_TO_ACCEPT    #allow everything by default
407 options         IPV6FIREWALL            #firewall for IPv6
408 options         IPV6FIREWALL_VERBOSE
409 options         IPV6FIREWALL_VERBOSE_LIMIT=100
410 options         IPV6FIREWALL_DEFAULT_TO_ACCEPT
411 options         IPDIVERT                #divert sockets
412 options         IPSTEALTH               #support for stealth forwarding
413 options         TCPDEBUG
414 options         ICMPPRINTFS
416 options         IPFIREWALL3
418 device          pf
419 device          pflog
421 #CARP
422 pseudo-device carp
423 options CARP
425 # The MBUF_STRESS_TEST option enables options which create
426 # various random failures / extreme cases related to mbuf
427 # functions.  See the mbuf(9) manpage for a list of available
428 # test cases.
429 options         MBUF_STRESS_TEST
431 # Statically link in accept filters
432 options                ACCEPT_FILTER_DATA
433 options                ACCEPT_FILTER_HTTP
435 # TCP_SIGNATURE adds support for RFC 2385 (TCP-MD5) digests. These are
436 # carried in TCP option 19. This option is commonly used to protect
437 # TCP sessions (e.g. BGP) where IPSEC is not available nor desirable.
438 # This is enabled on a per-socket basis using the TCP_SIGNATURE_ENABLE
439 # socket option.
440 # This requires the use of 'device crypto', 'options IPSEC'
441 # or 'device cryptodev'.
442 options   TCP_SIGNATURE   #include support for RFC 2385
445 # TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
446 # prevents nmap et al. from identifying the TCP/IP stack, but breaks support
447 # for RFC1644 extensions and is not recommended for web servers.
449 options         TCP_DROP_SYNFIN         #drop TCP packets with SYN+FIN
451 # ICMP_BANDLIM enables icmp error response bandwidth limiting.   You
452 # typically want this option as it will help protect the machine from
453 # D.O.S. packet attacks.
455 options         ICMP_BANDLIM
457 # DUMMYNET enables the "dummynet" bandwidth limiter. You need
458 # IPFIREWALL as well. See the dummynet(4) and ipfw(8) manpages for more info.
460 options         DUMMYNET
461 options         DUMMYNET_DEBUG
463 # IFPOLL_ENABLE adds support for mixed interrupt-polling handling
464 # of network device drivers, which has significant benefits in terms
465 # of robustness to overloads and responsivity, as well as permitting
466 # accurate scheduling of the CPU time between kernel network processing
467 # and other activities. The drawback is a moderate (up to 1/pollhz seconds)
468 # potential increase in response times. See polling(4) for further details.
470 # IFPOLL_ENABLE adds hardware queues' based polling
471 options         IFPOLL_ENABLE
473 #####################################################################
474 # FILESYSTEM OPTIONS
477 # Only the root, /usr, and /tmp filesystems need be statically
478 # compiled; everything else will be automatically loaded at mount
479 # time.  (Exception: the UFS family --- FFS, and MFS ---
480 # cannot currently be demand-loaded.)  Some people still prefer
481 # to statically compile other filesystems as well.
483 # NB: The PORTAL filesystem is known to be
484 # buggy, and WILL panic your system if you attempt to do anything with
485 # it.  It is included here as an incentive for some enterprising
486 # soul to sit down and fix it.
489 # One of these is mandatory:
490 options         FFS                     #Fast filesystem
491 options         MFS                     #Memory filesystem
492 options         NFS                     #Network filesystem
494 # The rest are optional:
495 #options        NFS_NOSERVER            #Disable the NFS-server code.
496 options         AUTOFS                  #Automounter filesystem
497 options         CD9660                  #ISO 9660 filesystem
498 options         HAMMER                  #HAMMER filesystem
499 options         HPFS                    #OS/2 File system
500 options         MSDOSFS                 #MS DOS filesystem
501 options         NTFS                    #NT filesystem
502 options         NULLFS                  #NULL filesystem
503 options         PORTAL                  #Portal filesystem
504 options         PROCFS                  #Process filesystem
505 options         PUFFS                   #Userspace file systems (e.g. ntfs-3g & sshfs)
506 options         SMBFS                   #SMB/CIFS filesystem
507 options         TMPFS                   #Temporary filesystem
508 options         UDF                     #UDF filesystem
510 # The xFS_ROOT options REQUIRE the associated ``options xFS''
511 options         FFS_ROOT                #FFS usable as root device
512 options         NFS_ROOT                #NFS usable as root device
514 # Soft updates is technique for improving UFS filesystem speed and
515 # making abrupt shutdown less risky.
516 options         SOFTUPDATES
518 # Directory hashing improves the speed of operations on very large
519 # directories at the expense of some memory.
520 options         UFS_DIRHASH
522 # Make space in the kernel for a root filesystem on a md device.
523 # Define to the number of kilobytes to reserve for the filesystem.
524 options         MD_ROOT_SIZE=10
526 # Make the md device a potential root device, either with preloaded
527 # images of type mfs_root or md_root.
528 options         MD_ROOT
530 # Specify double the default maximum size for malloc(9)-backed md devices.
531 options         MD_NSECT=40000
533 # Allow this many swap-devices.
535 # In order to manage swap, the system must reserve bitmap space that
536 # scales with the largest mounted swap device multiplied by NSWAPDEV,
537 # regardless of whether other swap devices exist or not.  So it
538 # is not a good idea to make this value too large.
539 options         NSWAPDEV=5
541 # Disk quotas are supported when this option is enabled.
542 options         QUOTA                   #enable disk quotas
544 # If you are running a machine just as a fileserver for PC and MAC
545 # users, e.g. using SAMBA, you may consider setting this option
546 # and keeping all those users' directories on a filesystem that is
547 # mounted with the suiddir option. This gives new files the same
548 # ownership as the directory (similar to group). It's a security hole
549 # if you let these users run programs, so confine it to file-servers
550 # (but it'll save you lots of headaches in those cases). Root owned
551 # directories are exempt and X bits are cleared. The suid bit must be
552 # set on the directory as well; see chmod(1) PC owners can't see/set
553 # ownerships so they keep getting their toes trodden on. This saves
554 # you all the support calls as the filesystem it's used on will act as
555 # they expect: "It's my dir so it must be my file".
557 options         SUIDDIR
559 # NFS options:
560 options         NFS_MINATTRTIMO=3       # VREG attrib cache timeout in sec
561 options         NFS_MAXATTRTIMO=60
562 options         NFS_MINDIRATTRTIMO=30   # VDIR attrib cache timeout in sec
563 options         NFS_MAXDIRATTRTIMO=60
564 options         NFS_GATHERDELAY=10      # Default write gather delay (msec)
565 options         NFS_UIDHASHSIZ=29       # Tune the size of nfssvc_sock with this
566 options         NFS_WDELAYHASHSIZ=16    # and with this
567 options         NFS_MUIDHASHSIZ=63      # Tune the size of nfsmount with this
568 options         NFS_DEBUG               # Enable NFS Debugging
570 # NTFS options:
571 options         NTFS_DEBUG
573 # MSDOSFS options:
574 options         MSDOSFS_DEBUG           # Enable MSDOSFS Debugging
577 # Add support for the EXT2FS filesystem of Linux fame.  Be a bit
578 # careful with this - the ext2fs code has a tendency to lag behind
579 # changes and not be exercised very much, so mounting read/write could
580 # be dangerous (and even mounting read only could result in panics.)
582 options         EXT2FS
584 # Optional character code conversion support with LIBICONV.
585 # Each option requires their base file system and LIBICONV.
586 options         CD9660_ICONV
587 options         MSDOSFS_ICONV
588 options         NTFS_ICONV
590 #####################################################################
591 # POSIX P1003.1B
593 # Real time extensions added in the 1993 Posix
594 # _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
596 options         _KPOSIX_PRIORITY_SCHEDULING
598 #####################################################################
599 # CLOCK OPTIONS
601 # The granularity of operation is controlled by the kernel option HZ whose
602 # default value (100) means a granularity of 10ms (1s/HZ).
603 # Consider, however, that reducing the granularity too much might
604 # cause excessive overhead in clock interrupt processing,
605 # potentially causing ticks to be missed and thus actually reducing
606 # the accuracy of operation.
608 options         HZ=100
610 # The following options are used for debugging clock behavior only, and
611 # should not be used for production systems.
613 # CLK_CALIBRATION_LOOP will run the clock calibration loop at startup
614 # until the user presses a key.
616 #options        CLK_CALIBRATION_LOOP
618 # The following two options measure the frequency of the corresponding
619 # clock relative to the RTC (onboard mc146818a).
621 #options        CLK_USE_I8254_CALIBRATION
622 #options        CLK_USE_TSC_CALIBRATION
624 #####################################################################
625 # SCSI DEVICES
627 # SCSI DEVICE CONFIGURATION
629 # The SCSI subsystem consists of the `base' SCSI code, a number of
630 # high-level SCSI device `type' drivers, and the low-level host-adapter
631 # device drivers.  The host adapters are listed in the ISA and PCI
632 # device configuration sections below.
634 # Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
635 # that a given bus, target, and LUN always come on line as the same
636 # device unit.  In earlier versions the unit numbers were assigned
637 # in the order that the devices were probed on the SCSI bus.  This
638 # means that if you removed a disk drive, you may have had to rewrite
639 # your /etc/fstab file, and also that you had to be careful when adding
640 # a new disk as it may have been probed earlier and moved your device
641 # configuration around.
643 # This old behavior is maintained as the default behavior.  The unit
644 # assignment begins with the first non-wired down unit for a device
645 # type.  For example, if you wire a disk as "da3" then the first
646 # non-wired disk will be assigned da4.
648 # The syntax for wiring down devices is:
650 # device        scbus0 at ahc0          # Single bus device
651 # device        scbus1 at ahc1 bus 0    # Single bus device
652 # device        scbus3 at ahc2 bus 0    # Twin bus device
653 # device        scbus2 at ahc2 bus 1    # Twin bus device
654 # device        da0 at scbus0 target 0 unit 0
655 # device        da1 at scbus3 target 1
656 # device        da2 at scbus2 target 3
657 # device        sa1 at scbus1 target 6
658 # device        cd
660 # "units" (SCSI logical unit number) that are not specified are
661 # treated as if specified as LUN 0.
663 # All SCSI devices allocate as many units as are required.
665 # The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
666 # configuration and doesn't have to be explicitly configured.
668 device          scbus                   #base SCSI code
669 device          ch                      #SCSI media changers
670 device          da                      #SCSI direct access devices (aka disks)
671 device          sa                      #SCSI tapes
672 device          cd                      #SCSI CD-ROMs
673 device          pass                    #CAM passthrough driver
674 device          sg                      #Passthrough device (linux scsi generic)
675 device          pt                      #SCSI processor type
676 device          ses                     #SCSI SES/SAF-TE driver
677 device          targ                    #SCSI Target Mode Code
678 device          targbh                  #SCSI Target Mode Blackhole Device
680 # Options for device mapper
681 device          dm
682 device          dm_target_crypt
683 device          dm_target_linear
684 device          dm_target_striped
685 device          dm_target_delay
686 device          dm_target_flakey
688 # Options for iSCSI
689 device          iscsi_initiator
690 options         ISCSI_INITIATOR_DEBUG=8
692 # CAM OPTIONS:
693 # debugging options:
694 # -- NOTE --  If you specify one of the bus/target/lun options, you must
695 #             specify them all!
696 # CAMDEBUG: When defined enables debugging macros
697 # CAM_DEBUG_BUS:  Debug the given bus.  Use -1 to debug all busses.
698 # CAM_DEBUG_TARGET:  Debug the given target.  Use -1 to debug all targets.
699 # CAM_DEBUG_LUN:  Debug the given lun.  Use -1 to debug all luns.
700 # CAM_DEBUG_FLAGS:  OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
701 #                   CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
703 # CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
704 # SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
705 # SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
706 # SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
707 #             queue after a bus reset, and the number of milliseconds to
708 #             freeze the device queue after a bus device reset.  This
709 #             can be changed at boot and runtime with the
710 #             kern.cam.scsi_delay tunable/sysctl.
711 options         CAMDEBUG
712 options         CAM_DEBUG_BUS=-1
713 options         CAM_DEBUG_TARGET=-1
714 options         CAM_DEBUG_LUN=-1
715 options         CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
716 options         CAM_MAX_HIGHPOWER=4
717 options         SCSI_NO_SENSE_STRINGS
718 options         SCSI_NO_OP_STRINGS
719 options         SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
721 # Options for the CAM CDROM driver:
722 # CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
723 # CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
724 #                           enforced if there is I/O waiting for another LUN
725 # The compiled in defaults for these variables are 2 and 10 seconds,
726 # respectively.
728 # These can also be changed on the fly with the following sysctl variables:
729 # kern.cam.cd.changer.min_busy_seconds
730 # kern.cam.cd.changer.max_busy_seconds
732 options         CHANGER_MIN_BUSY_SECONDS=2
733 options         CHANGER_MAX_BUSY_SECONDS=10
735 # Options for the CAM sequential access driver:
736 # SA_IO_TIMEOUT: Timeout for read/write/wfm  operations, in minutes
737 # SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
738 # SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
739 # SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
740 # SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
741 options         SA_IO_TIMEOUT="(4)"
742 options         SA_SPACE_TIMEOUT="(60)"
743 options         SA_REWIND_TIMEOUT="(2*60)"
744 options         SA_ERASE_TIMEOUT="(4*60)"
745 options         SA_1FM_AT_EOD
747 # Optional timeout for the CAM processor target (pt) device
748 # This is specified in seconds.  The default is 60 seconds.
749 options         SCSI_PT_DEFAULT_TIMEOUT="60"
751 # Optional enable of doing SES passthrough on other devices (e.g., disks)
753 # Normally disabled because a lot of newer SCSI disks report themselves
754 # as having SES capabilities, but this can then clot up attempts to build
755 # build a topology with the SES device that's on the box these drives
756 # are in....
757 options         SES_ENABLE_PASSTHROUGH
759 #####################################################################
760 # MISCELLANEOUS DEVICES AND OPTIONS
762 # The `pty' device usually turns out to be ``effectively mandatory'',
763 # as it is required for `telnetd', `rlogind', `screen', `emacs', and
764 # `xterm', among others.
766 pseudo-device   pty             # Pseudo ttys
767 pseudo-device   gzip            # Exec gzipped a.out's
768 pseudo-device   md              # Memory/malloc disk
769 pseudo-device   vn              # File image "disks"
770 pseudo-device   putter          # for puffs and pud
771 pseudo-device   snp             # Snoop device - to look at pty/vty/etc..
772 pseudo-device   ccd     4       # Concatenated disk driver
774 # Configuring Vinum into the kernel is not necessary, since the kld
775 # module gets started automatically when vinum(8) starts.  This
776 # device is also untested.  Use at your own risk.
778 # The option VINUMDEBUG must match the value set in CFLAGS
779 # in src/sbin/vinum/Makefile.  Failure to do so will result in
780 # the following message from vinum(8):
782 # Can't get vinum config: Invalid argument
784 # see vinum(4) for more reasons not to use these options.
785 pseudo-device   vinum           #Vinum concat/mirror/raid driver
786 options         VINUMDEBUG      #enable Vinum debugging hooks
788 # Kernel side iconv library
789 options         LIBICONV
791 # Size of the kernel message buffer.  Should be N * pagesize.
792 options         MSGBUF_SIZE=40960
794 #####################################################################
795 # HARDWARE DEVICE CONFIGURATION
797 # ISA devices:
800 # Mandatory ISA devices: isa
802 device          isa
805 # Options for `isa':
807 # AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
808 # interrupt controller.  This saves about 0.7-1.25 usec for each interrupt.
809 # This option breaks suspend/resume on some portables.
811 # AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
812 # interrupt controller.  This saves about 0.7-1.25 usec for each interrupt.
813 # Automatic EOI is documented not to work for the slave with the
814 # original i8259A, but it works for some clones and some integrated
815 # versions.
817 # MAXMEM specifies the amount of RAM on the machine; if this is not
818 # specified, DragonFly will first read the amount of memory from the CMOS
819 # RAM, so the amount of memory will initially be limited to 64MB or 16MB
820 # depending on the BIOS.  If the BIOS reports 64MB, a memory probe will
821 # then attempt to detect the installed amount of RAM.  If this probe
822 # fails to detect >64MB RAM you will have to use the MAXMEM option.
823 # The amount is in kilobytes, so for a machine with 128MB of RAM, it would
824 # be 131072 (128 * 1024).
826 # BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
827 # reset the CPU for reboot.  This is needed on some systems with broken
828 # keyboard controllers.
830 options         AUTO_EOI_1
831 #options        AUTO_EOI_2
832 options         MAXMEM="(128*1024)"
833 #options        BROKEN_KEYBOARD_RESET
835 # Enable support for the kernel PLL to use an external PPS signal,
836 # under supervision of [x]ntpd(8)
837 # More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
839 options         PPS_SYNC
841 # The keyboard controller; it controls the keyboard and the PS/2 mouse.
842 device          atkbdc0 at isa? port IO_KBD
844 # The AT keyboard
845 device          atkbd0  at atkbdc? irq 1
847 # Options for atkbd:
848 options         ATKBD_DFLT_KEYMAP       # specify the built-in keymap
849 makeoptions     ATKBD_DFLT_KEYMAP="jp.106"
851 # These options are valid for other keyboard drivers as well.
852 options         KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
853 options         KBD_INSTALL_CDEV        # install a CDEV entry in /dev
855 # `flags' for atkbd:
856 #       0x01    Force detection of keyboard, else we always assume a keyboard
857 #       0x02    Don't reset keyboard, useful for some newer ThinkPads
858 #       0x03    Force detection and avoid reset, might help with certain
859 #               dockingstations
860 #       0x04    Old-style (XT) keyboard support, useful for older ThinkPads
862 # PS/2 mouse
863 device          psm0    at atkbdc? irq 12
865 # Options for psm:
866 options         PSM_HOOKRESUME          #hook the system resume event, useful
867                                         #for some laptops
868 options         PSM_RESETAFTERSUSPEND   #reset the device at the resume event
870 device          kbdmux                  # keyboard multiplexer
872 # The video card driver.
873 device          vga0    at isa?
875 # Options for vga:
876 options         VGA_DEBUG=2             # enable VGA debug output
878 # If you experience problems switching back to 80x25 (or a derived mode),
879 # the following option might help.
880 #options        VGA_KEEP_POWERON_MODE   # use power-on settings for 80x25
882 # If you can dispense with some vga driver features, you may want to
883 # use the following options to save some memory.
884 #options        VGA_NO_FONT_LOADING     # don't save/load font
885 #options        VGA_NO_MODE_CHANGE      # don't change video modes
887 # The following option probably won't work with the LCD displays.
888 options         VGA_WIDTH90             # support 90 column modes
890 # Splash screen at start up!  Screen savers require this too.
891 pseudo-device   splash
893 # The syscons console driver (sco color console compatible).
894 device          sc0     at isa?
895 options         MAXCONS=16              # number of virtual consoles
896 options         SC_ALT_MOUSE_IMAGE      # simplified mouse cursor in text mode
897 options         SC_DEBUG_LEVEL=5        # enable debug output
898 options         SC_DFLT_FONT            # compile font in
899 makeoptions     SC_DFLT_FONT=cp850
900 options         SC_DISABLE_DDBKEY       # disable `debug' key
901 options         SC_DISABLE_REBOOT       # disable reboot key sequence
902 options         SC_HISTORY_SIZE=200     # number of history buffer lines
903 options         SC_MOUSE_CHAR=0x3       # char code for text mode mouse cursor
904 options         SC_PIXEL_MODE           # add support for the raster text mode
906 # The following options will let you change the default colors of syscons.
907 options         SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
908 options         SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
909 options         SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
910 options         SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
911 options         SC_BORDER_COLOR="FG_BLACK"
913 # If you have a two button mouse, you may want to add the following option
914 # to use the right button of the mouse to paste text.
915 options         SC_TWOBUTTON_MOUSE
917 # You can selectively disable features in syscons.
918 #options        SC_NO_CUTPASTE
919 #options        SC_NO_FONT_LOADING
920 #options        SC_NO_HISTORY
921 #options        SC_NO_SYSMOUSE
924 # SCSI host adapters
926 # adv: All Narrow SCSI bus AdvanSys controllers.
927 # adw: Second Generation AdvanSys controllers including the ADV940UW.
928 # ahc: Adaptec 274x/284x/294x
929 # aic: Adaptec 1460
930 # bt: Most Buslogic controllers
931 # ncv: NCR 53C500 based SCSI host adapters.
932 # nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
933 # stg: TMC 18C30, 18C50 based PC Card SCSI host adapters.
935 # Note that the order is important in order for Buslogic cards to be
936 # probed correctly.
939 device          bt
940 device          adv
941 device          adw
942 device          aic
943 device          ncv
944 device          nsp
945 device          stg
948 # Adaptec FSA RAID controllers, including integrated DELL controller,
949 # the Dell PERC 2/QC and the HP NetRAID-4M
951 device          aac
952 options         AAC_DEBUG
953 device          aacp    # SCSI Passthrough interface (optional, CAM required)
956 # Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers.  Only
957 # one entry is needed; the code will find and configure all supported
958 # controllers.
960 device          ida             # Compaq Smart RAID
961 device          mlx             # Mylex DAC960
962 device          amr             # AMI MegaRAID
963 device          amrp            # SCSI Passthrough interface (optional, CAM req.)
964 options         AMR_DEBUG=3
965 device          mfi             # LSI MegaRAID SAS
966 device          mfip            # LSI MegaRAID SAS passthrough, requires CAM
967 options         MFI_DEBUG
970 # LSI MegaRAID 6Gb/s and 12Gb/s SAS+SATA RAID controller driver
972 device          mrsas
975 # Areca RAID (CAM is required).
977 device          arcmsr          # Areca SATA II RAID
980 # Highpoint RocketRAID 182x.
981 device          hptmv
984 # Highpoint RocketRAID.  Supports RR172x, RR222x, RR2240, RR232x, RR2340,
985 # RR2210, RR174x, RR2522, RR231x, RR230x.
986 device          hptrr
989 # Highpoint RocketRAID 27xx.
990 device          "hpt27xx"
993 # Highpoint RocketRaid 3xxx series SATA RAID
994 device          hptiop
997 # 3ware ATA RAID
999 device          twe             # 3ware ATA RAID
1000 device          twa             # 3ware 9000 series PATA/SATA RAID
1001 options         TWA_DEBUG=10    # enable debug messages
1002 device          tws             # 3ware 9750 series SATA/SAS RAID
1005 # IBM ServeRAID
1007 device  ips
1009 # AHCI driver, this will override NATA for AHCI devices,
1010 # both drivers may be included.
1012 device          ahci
1014 # NVME driver
1016 device          nvme
1018 # SiI3124/3132 driver
1020 device          sili
1022 # The 'NATA' driver supports all ATA and ATAPI devices.
1023 # You only need one "device nata" for it to find all
1024 # PCI ATA/ATAPI devices on modern machines.
1026 device          nata
1027 device          natadisk        # ATA disk drives
1028 device          natapicd        # ATAPI CD/DVD drives
1029 device          natapifd        # ATAPI floppy drives
1030 device          natapist        # ATAPI tape drives
1031 device          natapicam       # ATAPI CAM layer emulation
1032 device          nataraid        # support for ATA software RAID controllers
1034 # The following options are valid for the NATA driver:
1036 # ATA_STATIC_ID:        controller numbering is static (like the old driver)
1037 #                       else the device numbers are dynamically allocated.
1038 options         ATA_STATIC_ID
1040 # For older non-PCI systems, these are the lines to use:
1042 #device         nata0   at isa? port IO_WD1 irq 14
1043 #device         nata1   at isa? port IO_WD2 irq 15
1046 # Standard floppy disk controllers: `fdc' and `fd'
1048 #device         fdc0    at isa? port IO_FD1 irq 6 drq 2
1050 # FDC_DEBUG enables floppy debugging.  Since the debug output is huge, you
1051 # gotta turn it actually on by setting the variable fd_debug with DDB,
1052 # however.
1053 #options        FDC_DEBUG
1055 #device         fd0     at fdc0 drive 0
1056 #device         fd1     at fdc0 drive 1
1059 # sio: serial ports (see sio(4))
1061 device          sio0    at isa? port IO_COM1 flags 0x10 irq 4
1064 # `flags' for serial drivers that support consoles (only for sio now):
1065 #       0x10    enable console support for this unit.  The other console flags
1066 #               are ignored unless this is set.  Enabling console support does
1067 #               not make the unit the preferred console - boot with -h or set
1068 #               the 0x20 flag for that.  Currently, at most one unit can have
1069 #               console support; the first one (in config file order) with
1070 #               this flag set is preferred.  Setting this flag for sio0 gives
1071 #               the old behaviour.
1072 #       0x20    force this unit to be the console (unless there is another
1073 #               higher priority console).  This replaces the COMCONSOLE option.
1074 #       0x40    reserve this unit for low level console operations.  Do not
1075 #               access the device in any normal way.
1076 #       0x80    use this port for serial line gdb support in ddb.
1079 # Options for serial drivers that support consoles (only for sio now):
1080 options         BREAK_TO_DEBUGGER       #a BREAK on a comconsole goes to
1081                                         #DDB, if available.
1082 options         CONSPEED=115200         # speed for serial console
1083                                         # (default 9600)
1085 # Solaris implements a new BREAK which is initiated by a character
1086 # sequence CR ~ ^b which is similar to a familiar pattern used on
1087 # Sun servers by the Remote Console.
1088 options         ALT_BREAK_TO_DEBUGGER
1090 # Options for sio:
1091 options         COM_ESP                 #code for Hayes ESP
1092 options         COM_MULTIPORT           #code for some cards with shared IRQs
1094 # Other flags for sio that aren't documented in the man page.
1095 #       0x20000 enable hardware RTS/CTS and larger FIFOs.  Only works for
1096 #               ST16650A-compatible UARTs.
1098 # PCI Universal Communications driver
1099 # Supports various single and multi port PCI serial cards. Maybe later
1100 # also the parallel ports on combination serial/parallel cards. New cards
1101 # can be added in src/sys/dev/misc/puc/pucdata.c.
1102 device          puc
1105 # Network interfaces: `is', `lnc'
1107 # lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
1108 # sbsh: Granch SBNI16 SHDSL modem PCI adapters
1109 # wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
1110 #     the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
1111 #     bridge with a PCMCIA adapter plugged into it.
1112 # xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
1114 device lnc
1115 device sln
1116 device sn
1118 # Wlan support is mandatory for some wireless LAN devices.
1119 options         IEEE80211_DEBUG         #enable debugging msgs
1120 options         IEEE80211_SUPPORT_MESH  #enable 802.11s D3.0 support
1121 options         IEEE80211_SUPPORT_TDMA  #enable TDMA support
1122 device          wlan            # 802.11 support
1123 device          wlan_acl        # 802.11 MAC-based access control for AP
1124 device          wlan_ccmp       # 802.11 CCMP support
1125 device          wlan_tkip       # 802.11 TKIP support
1126 device          wlan_wep        # 802.11 WEP support
1127 device          wlan_xauth      # 802.11 WPA or 802.1x authentication for AP
1128 device          wlan_amrr       # 802.11 AMRR TX rate control algorithm
1129 device          ath             # Atheros AR521x
1130 options         AH_AR5416_INTERRUPT_MITIGATION
1131 options         AH_ASSERT
1132 options         AH_DEBUG
1133 options         AH_INTERRUPT_DEBUGGING
1134 options         AH_MAXCHAN=96
1135 options         AH_NEED_DESC_SWAP
1136 options         AH_PRIVATE_DIAG
1137 options         AH_RXCFG_SDMAMW_4BYTES
1138 options         AH_SUPPORT_AR5416
1139 options         AH_SUPPORT_AR9130
1140 options         AH_SUPPORT_AR9330
1141 options         AH_SUPPORT_AR9340
1142 options         AH_USE_INIPDGAIN
1143 device          ath_hal         # Atheros Hardware Access Layer
1144 #device         ath_rate_amrr   # Atheros AMRR TX rate control algorithm
1145 #device         ath_rate_onoe   # Atheros Onoe TX rate control algorithm
1146 device          ath_rate_sample # Atheros Sample TX rate control algorithm
1147 options         ATH_DEBUG       # turn on debugging output (see hw.ath.debug)
1148 options         ATH_DIAGAPI     # diagnostic interface to the HAL
1149 options         ATH_ENABLE_DFS
1150 options         ATH_KTR_INTR_DEBUG
1151 device          siba_bwn        # Sonic Inc. Silicon Backplane needed for bwn
1152 options         SIBA_DEBUG      # turn on debugging output
1153 device          bwn             # Broadcom BCM43xx NICs using v4 firmware
1154 options         BWN_DEBUG       # turn on debugging output
1155 options         BWN_RXRING_SLOTS=128    # number of RX slots to allocate
1156 options         BWN_TXRING_SLOTS=128    # number of TX slots to allocate
1157 device          iwi             # Intel PRO/Wireless 2200BG/2915ABG
1158 device          iwm             # Intel Dual Band Wireless AC 316x/726x/826x
1159 options         IWM_DEBUG       # turn on debugging output
1160 device          iwn             # Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1161 options         IWN_DEBUG       # turn on debugging output
1162 device          wi              # WaveLAN/IEEE, PRISM-II, Spectrum24 802.11DS
1163 device          xe              # Xircom PCMCIA
1164 device          ral             # Ralink Technology 802.11 wireless NIC
1165 device          wpi
1166 options         WPI_DEBUG       # turn on debugging output
1168 # IEEE 802.11 adapter firmware modules
1170 # iwifw:        Intel PRO/Wireless 2200BG/2225BG/2915ABG firmware
1171 # iwmfw         Intel Dual Band Wireless AC 3160/3165/3168/7260/7265/8260/8265
1172 # iwnfw:        Intel WiFi Link 4965/1000/5000/5150/5300/6000/6050
1173 # ralfw:        Ralink Technology RT25xx and RT26xx firmware
1174 # wpifw:        Intel 3945ABG Wireless LAN Controller firmware
1176 device          iwifw
1177 device          iwmfw
1178 device          iwnfw
1179 device          ralfw
1180 device          wpifw
1182 # Bluetooth Protocols
1183 device          bluetooth
1185 # Sound drivers
1188 # Basic sound card support:
1189 device          sound
1190 # For PCI sound cards:
1191 device          "snd_als4000"
1192 device          "snd_atiixp"
1193 device          "snd_cmi"
1194 device          "snd_cs4281"
1195 device          "snd_emu10k1"
1196 device          "snd_emu10kx"
1197 device          "snd_envy24"
1198 device          "snd_envy24ht"
1199 device          "snd_es137x"
1200 device          "snd_fm801"
1201 device          "snd_hda"
1202 device          "snd_hdspe"
1203 device          "snd_ich"
1204 device          "snd_maestro"
1205 device          "snd_neomagic"
1206 device          "snd_solo"
1207 device          "snd_spicds"
1208 device          "snd_t4dwave"
1209 device          "snd_via8233"
1210 device          "snd_via82c686"
1211 device          "snd_vibes"
1212 # USB
1213 device          "snd_uaudio"
1216 # Following options are intended for debugging/testing purposes:
1218 # SND_DEBUG                    Enable extra debugging code that includes
1219 #                              sanity checking and possible increase of
1220 #                              verbosity.
1222 # SND_DIAGNOSTIC               Similar in a spirit of INVARIANTS/DIAGNOSTIC,
1223 #                              zero tolerance against inconsistencies.
1225 # SND_FEEDER_MULTIFORMAT       By default, only 16/32 bit feeders are compiled
1226 #                              in. This options enable most feeder converters
1227 #                              except for 8bit. WARNING: May bloat the kernel.
1229 # SND_FEEDER_FULL_MULTIFORMAT  Ditto, but includes 8bit feeders as well.
1231 # SND_FEEDER_RATE_HP           (feeder_rate) High precision 64bit arithmetic
1232 #                              as much as possible (the default trying to
1233 #                              avoid it). Possible slowdown.
1235 # SND_PCM_64                   (Only applicable for i386/32bit arch)
1236 #                              Process 32bit samples through 64bit
1237 #                              integer/arithmetic. Slight increase of dynamic
1238 #                              range at a cost of possible slowdown.
1240 # SND_OLDSTEREO                Only 2 channels are allowed, effectively
1241 #                              disabling multichannel processing.
1243 options         SND_DEBUG
1244 #options                SND_DIAGNOSTIC
1245 options         SND_FEEDER_MULTIFORMAT
1246 options         SND_FEEDER_FULL_MULTIFORMAT
1247 options         SND_FEEDER_RATE_HP
1248 options         SND_PCM_64
1249 options         SND_OLDSTEREO
1252 # Miscellaneous hardware:
1254 # bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
1255 # coremctl: Intel Core/E3 memory controller (required by ecc(4) and memtemp(4))
1256 # dimm: Location inforamtion (required by ecc(4) and memtemp(4))
1257 # ecc: ECC memory controller
1258 # ipmi: Intelligent Platform Management Interface
1259 # joy: joystick
1260 # nrp: Comtrol Rocketport
1261 # si: Specialix SI/XIO 4-32 port terminal multiplexor
1262 # nmdm: nullmodem terminal driver (see nmdm(4))
1263 # tpm: Trusted Platform Module
1265 # Notes on the Specialix SI/XIO driver:
1266 #  **This is NOT a Specialix supported Driver!**
1267 #  The host card is memory, not IO mapped.
1268 #  The Rev 1 host cards use a 64K chunk, on a 32K boundary.
1269 #  The Rev 2 host cards use a 32K chunk, on a 32K boundary.
1270 #  The cards can use an IRQ of 11, 12 or 15.
1272 device          coremctl
1273 device          dimm
1274 device          ecc
1275 device          joy0    at isa? port IO_GAME
1276 device          nrp
1277 device          si
1278 # nullmodem terminal driver
1279 device          nmdm
1280 device          tpm
1281 device          ipmi
1283 # The `ahc' device provides support for the Adaptec 274X and 284X
1284 # adapters.
1285 device          ahc
1287 # The aic7xxx driver will attempt to use memory mapped I/O for all PCI
1288 # controllers that have it configured only if this option is set. Unfortunately,
1289 # this doesn't work on some motherboards, which prevents it from being the
1290 # default.
1291 options         AHC_ALLOW_MEMIO
1293 # The adw driver will attempt to use memory mapped I/O for all PCI
1294 # controllers that have it configured only if this option is set.
1295 options         ADW_ALLOW_MEMIO
1298 # PCI devices & PCI options:
1300 # The main PCI bus device is `pci'.  It provides auto-detection and
1301 # configuration support for all devices on the PCI bus, using either
1302 # configuration mode defined in the PCI specification.
1304 device          pci
1306 # AGP GART support
1308 device          agp
1311 # AGP debugging.
1313 options                AGP_DEBUG
1315 # The `ahc' device provides support for the Adaptec 29/3940(U)(W)
1316 # and motherboard based AIC7870/AIC7880 adapters.
1317 options         AHC_DEBUG
1318 options         AHC_DEBUG_OPTS=0xffffffff
1319 options         AHC_REG_PRETTY_PRINT
1320 options         AHC_TMODE_ENABLE
1322 # The 'ahd' device provides support for the Adaptec 79xx Ultra320
1323 # SCSI adapters. Options are documented in the ahd(4) manpage:
1324 options         AHD_DEBUG
1325 options         AHD_DEBUG_OPTS=0xffffffff
1326 options         AHD_REG_PRETTY_PRINT
1327 #options        AHD_TMODE_ENABLE=0xff
1329 # The `amd' device provides support for the AMD 53C974 SCSI host
1330 # adapter chip as found on devices such as the Tekram DC-390(T).
1332 # The `bge' device provides support for gigabit ethernet adapters
1333 # based on the Broadcom BCM570x family of controllers, including the
1334 # 3Com 3c996-T, the Netgear GA302T, the SysKonnect SK-9D21 and SK-9D41,
1335 # and the embedded gigE NICs on Dell PowerEdge 2550 servers.
1337 # The `ncr' device provides support for the NCR 53C810 and 53C825
1338 # self-contained SCSI host adapters.
1340 # The `isp' device provides support for the Qlogic ISP 1020, 1040
1341 # nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
1342 # ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
1343 # the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
1345 # The `dc' device provides support for PCI fast ethernet adapters
1346 # based on the DEC/Intel 21143 and various workalikes including:
1347 # the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
1348 # AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
1349 # 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
1350 # and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
1351 # replaces the old al, ax, dm, pn and mx drivers.  List of brands:
1352 # Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
1353 # SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
1354 # LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
1355 # KNE110TX.
1357 # The `de' device provides support for the Digital Equipment DC21040
1358 # self-contained Ethernet adapter.
1360 # The `em' device provides support for the Intel Pro/1000 Family of Gigabit
1361 # adapters (82542, 82543, 82544, 82540).
1363 # The `et' device provides support for the Agere ET1310 10/100/1000 PCIe
1364 # adapters.
1366 # The `fxp' device provides support for the Intel EtherExpress Pro/100B
1367 # PCI Fast Ethernet adapters.
1369 # The 'lge' device provides support for PCI gigabit ethernet adapters
1370 # based on the Level 1 LXT1001 NetCellerator chipset. This includes the
1371 # D-Link DGE-500SX, SMC TigerCard 1000 (SMC9462SX), and some Addtron cards.
1373 # The 'my' device provides support for the Myson MTD80X and MTD89X PCI
1374 # Fast Ethernet adapters.
1376 # The 'nge' device provides support for PCI gigabit ethernet adapters
1377 # based on the National Semiconductor DP83820 and DP83821 chipset. This
1378 # includes the SMC EZ Card 1000 (SMC9462TX), D-Link DGE-500T, Asante
1379 # FriendlyNet GigaNIX 1000TA and 1000TPC, the Addtron AEG320T, the
1380 # LinkSys EG1032 and EG1064, the Surecom EP-320G-TX and the Netgear GA622T.
1382 # The 'oce' device provides support for Emulex 10 Gbit adapters
1383 # (OneConnect Ethernet).
1385 # The 'pcn' device provides support for PCI fast ethernet adapters based
1386 # on the AMD Am79c97x chipsets, including the PCnet/FAST, PCnet/FAST+,
1387 # PCnet/PRO and PCnet/Home. These were previously handled by the lnc
1388 # driver (and still will be if you leave this driver out of the kernel).
1390 # Te 're' device provides support for PCI GigaBit ethernet adapters based
1391 # on the RealTek 8169 chipset. It also supports the 8139C+ and is the
1392 # preferred driver for that chip.
1394 # The 'rl' device provides support for PCI fast ethernet adapters based
1395 # on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
1396 # to using programmed I/O to do register accesses because memory mapped
1397 # mode seems to cause severe lockups on SMP hardware. This driver also
1398 # supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
1399 # the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
1400 # workalike.  Note that the D-Link DFE-530TX+ uses the RealTek chipset
1401 # and is supported by this driver, not the 'vr' driver.
1403 # The 'sf' device provides support for Adaptec Duralink PCI fast
1404 # ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
1405 # This includes dual and quad port cards, as well as one 100baseFX card.
1406 # Most of these are 64-bit PCI devices, except for one single port
1407 # card which is 32-bit.
1409 # The 'ste' device provides support for adapters based on the Sundance
1410 # Technologies ST201 PCI fast ethernet controller. This includes the
1411 # D-Link DFE-550TX.
1413 # The 'sis' device provides support for adapters based on the Silicon
1414 # Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
1415 # chips.
1417 # The 'sk' device provides support for the SysKonnect SK-984x series
1418 # PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
1419 # single port cards (single mode and multimode fiber) and the
1420 # SK-9843 and SK-9844 dual port cards (also single mode and multimode).
1421 # The driver will autodetect the number of ports on the card and
1422 # attach each one as a separate network interface.
1424 # The 'ti' device provides support for PCI gigabit ethernet NICs based
1425 # on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
1426 # Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
1427 # Note that you will probably want to bump up NMBCLUSTERS a lot to use
1428 # this driver.
1430 # The 'tl' device provides support for the Texas Instruments TNETE100
1431 # series 'ThunderLAN' cards and integrated ethernet controllers. This
1432 # includes several Compaq Netelligent 10/100 cards and the built-in
1433 # ethernet controllers in several Compaq Prosignia, Proliant and
1434 # Deskpro systems. It also supports several Olicom 10Mbps and 10/100
1435 # boards.
1437 # The `tx' device provides support for the SMC 9432 TX, BTX and FTX cards.
1439 # The `txp' device provides support for the 3Com 3cR990 "Typhoon"
1440 # 10/100 adapters.
1442 # The `vr' device provides support for various fast ethernet adapters
1443 # based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
1444 # chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
1445 # Technologies PN102TX, and the AOpen/Acer ALN-320.
1447 # The `wb' device provides support for various fast ethernet adapters
1448 # based on the Winbond W89C840F chip. Note: this is not the same as
1449 # the Winbond W89C940F, which is an NE2000 clone.
1451 # The `xl' device provides support for the 3Com 3c900, 3c905 and
1452 # 3c905B (Fast) Etherlink XL cards and integrated controllers. This
1453 # includes the integrated 3c905B-TX chips in certain Dell Optiplex and
1454 # Dell Precision desktop machines and the integrated 3c905-TX chips
1455 # in Dell Latitude laptop docking stations.
1457 # The 'bktr' device is a PCI video capture device using the Brooktree
1458 # bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
1459 # TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
1460 # Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
1462 # options       OVERRIDE_CARD=xxx
1463 # options       OVERRIDE_TUNER=xxx
1464 # options       OVERRIDE_MSP=1
1465 # options       OVERRIDE_DBX=1
1466 # These options can be used to override the auto detection
1467 # The current values for xxx are found in src/sys/dev/video/bktr/bktr_card.h
1468 # Using sysctl(8) run-time overrides on a per-card basis can be made
1470 # options       BKTR_SYSTEM_DEFAULT=BROOKTREE_PAL
1471 # or
1472 # options       BKTR_SYSTEM_DEFAULT=BROOKTREE_NTSC
1473 # Specifies the default video capture mode.
1474 # This is required for Dual Crystal (28&35Mhz) boards where PAL is used
1475 # to prevent hangs during initialisation.  eg VideoLogic Captivator PCI.
1477 # options       BKTR_USE_PLL
1478 # PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
1479 # must enable PLL mode with this option. eg some new Bt878 cards.
1481 # options       BKTR_GPIO_ACCESS
1482 # This enable IOCTLs which give user level access to the GPIO port.
1484 # options       BKTR_NO_MSP_RESET
1485 # Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
1487 # options       BKTR_430_FX_MODE
1488 # Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
1490 # options       BKTR_SIS_VIA_MODE
1491 # Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
1492 # needed for some old SiS and VIA chipset motherboards.
1493 # This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
1494 # motherboards and motherboards with bad or incomplete PCI 2.1 support.
1495 # As a rough guess, old = before 1998
1497 # options       BKTR_NEW_MSP34XX_DRIVER
1498 # Use new, more complete initialization scheme for the msp34* soundchip.
1499 # Should fix stereo autodetection if the old driver does only output
1500 # mono sound.
1502 # options       BKTR_OVERRIDE_CARD=xxx
1503 # options       BKTR_OVERRIDE_DBX=xxx
1504 # options       BKTR_OVERRIDE_MSP=xxx
1505 # options       BKTR_OVERRIDE_TUNER=xxx
1506 # These options can be used to select a specific device, regardless of
1507 # the autodetection and i2c device checks (see comments in bktr_card.c).
1509 device          ahc             # AHA2940 and onboard AIC7xxx devices
1510 device          ahd             # AIC79xx devices
1511 device          amd             # AMD 53C974 (Tekram DC-390(T))
1512 device          isp             # Qlogic family
1513 device          ispfw           # Firmware for QLogic HBAs
1514 device          mpt             # LSI '909 FC adapters
1515 device          mps             # LSI-Logic MPT-Fusion 2
1516 device          ncr             # NCR/Symbios Logic
1517 device          sym             # NCR/Symbios Logic (newer chipsets)
1518 device          trm             # Tekram DC395U/UW/F and DC315U
1520 # Options for ISP
1522 #       ISP_TARGET_MODE         -       enable target mode operation
1523 #options        ISP_TARGET_MODE=1
1525 # Options used in dev/disk/sym/ (Symbios SCSI driver).
1526 #options        SYM_SETUP_LP_PROBE_MAP  #-Low Priority Probe Map (bits)
1527                                         # Allows the ncr to take precedence
1528                                         # 1 (1<<0) -> 810a, 860
1529                                         # 2 (1<<1) -> 825a, 875, 885, 895
1530                                         # 4 (1<<2) -> 895a, 896, 1510d
1531 #options        SYM_SETUP_SCSI_DIFF     #-HVD support for 825a, 875, 885
1532                                         # disabled:0 (default), enabled:1
1533 #options        SYM_SETUP_PCI_PARITY    #-PCI parity checking
1534                                         # disabled:0, enabled:1 (default)
1535 #options        SYM_SETUP_MAX_LUN       #-Number of LUNs supported
1536                                         # default:8, range:[1..64]
1539 # MII bus support is required for some PCI 10/100 ethernet NICs,
1540 # namely those which use MII-compliant transceivers or implement
1541 # transceiver control interfaces that operate like an MII. Adding
1542 # "device miibus0" to the kernel config pulls in support for
1543 # the generic miibus API and all of the PHY drivers, including a
1544 # generic one for PHYs that aren't specifically handled by an
1545 # individual driver.
1546 device          miibus
1548 # PCI Ethernet NICs that use the common MII bus controller code.
1549 device          ae              # Attansic/Atheros L2 Fast Ethernet
1550 device          alc             # Atheros AR8131/AR8132
1551 device          ale             # Atheros AR8121/AR8113/AR8114
1552 device          age             # Attansic/Atheros L1 Gigabit Ethernet
1553 device          bce             # Broadcom NetXtreme II Gigabit Ethernet
1554 device          bfe             # Broadcom BCM440x 10/100 Ethernet
1555 device          bnx             # Broadcom NetXtreme 5718/57785 Gigabit Ethernet
1556 device          dc              # DEC/Intel 21143 and various workalikes
1557 device          fxp             # Intel EtherExpress PRO/100B (82557, 82558)
1558 device          my              # Myson Fast Ethernet (MTD80X, MTD89X)
1559 device          pcn             # AMD Am79C97x PCI 10/100 NICs
1560 device          re              # RealTek 8139C+/8169
1561 device          rl              # RealTek 8129/8139
1562 device          sbsh            # Granch SBNI16 SHDSL modem
1563 device          sf              # Adaptec AIC-6915 (``Starfire'')
1564 device          sis             # Silicon Integrated Systems SiS 900/SiS 7016
1565 device          ste             # Sundance ST201 (D-Link DFE-550TX)
1566 device          tl              # Texas Instruments ThunderLAN
1567 device          tx              # SMC EtherPower II (83c17x ``EPIC'')
1568 device          vge             # VIA 612x GigE
1569 device          vr              # VIA Rhine, Rhine II
1570 device          wb              # Winbond W89C840F
1571 device          xl              # 3Com 3c90x (``Boomerang'', ``Cyclone'')
1573 # PCI Ethernet NICs.
1574 device          de              # DEC/Intel DC21x4x (``Tulip'')
1575 device          txp             # 3Com 3cR990 (``Typhoon'')
1577 # Gigabit Ethernet NICs.
1578 device          bge             # Broadcom BCM570x (``Tigon III'')
1579 device          em              # Intel Pro/1000 (8254x,8257x)
1580                                 # Requires ig_hal
1581 device          emx             # Intel Pro/1000 (8257{1,2,3,4})
1582                                 # Requires ig_hal
1583 device          igb             # Intel Pro/1000 (82575, 82576, 82580, i350)
1584                                 # Requires ig_hal
1585 device          ig_hal          # Intel Pro/1000 hardware abstraction layer
1586 device          ix              # Intel PRO/10GbE PCIE Ethernet Family
1587 device          et              # Agere ET1310 10/100/1000 Ethernet
1588 device          lge             # Level 1 LXT1001 (``Mercury'')
1589 device          mxge            # Myricom Myri-10G 10GbE NIC
1590 device          nfe             # nVidia nForce2/3 MCP04/51/55 CK804
1591 device          nge             # NatSemi DP83820 and DP83821
1592 device          oce             # Emulex 10 GbE (OneConnect Ethernet)
1593 device          sk              # SysKonnect GEnesis, LinkSys EG1023, D-Link
1594 device          ti              # Alteon (``Tigon I'', ``Tigon II'')
1595 device          stge            # Sundance/Tamarack TC9021 Gigabit Ethernet
1596 device          msk             # Marvell/SysKonnect Yukon II Gigabit Ethernet
1597 device          jme             # JMicron Gigabit/Fast Ethernet
1599 # Brooktree driver has been ported to the new I2C framework. Thus,
1600 # you'll need to have the following 3 lines in the kernel config.
1601 #     device smbus
1602 #     device iicbus
1603 #     device iicbb
1604 # The iic and smb devices are only needed if you want to control other
1605 # I2C slaves connected to the external connector of some cards.
1607 device          bktr
1608 options         BKTR_NEW_MSP34XX_DRIVER
1610 # WinTV PVR-250/350 driver
1611 device          cxm
1614 # PCCARD/PCMCIA
1616 # pccard: pccard slots
1617 # cardbus/cbb: cardbus bridge
1618 device          pccard
1619 device          cardbus
1620 device          cbb
1623 # MMC/SD
1625 # mmc           MMC/SD bus
1626 # mmcsd         MMC/SD memory card
1627 # sdhci         Generic PCI SD Host Controller
1629 device          mmc
1630 device          mmcsd
1631 device          sdhci
1634 # SMB bus
1636 # System Management Bus support is provided by the 'smbus' device.
1637 # Access to the SMBus device is via the 'smb' device (/dev/smb*),
1638 # which is a child of the 'smbus' device.
1640 # Supported devices:
1641 # smb           standard io through /dev/smb*
1643 # ACPI support:
1644 # smbacpi       support for ACPI I2cSerialBus resources
1646 # Supported SMB interfaces:
1647 # iicsmb        I2C to SMB bridge with any iicbus interface
1648 # bktr          brooktree848 I2C hardware interface
1649 # intpm         Intel PIIX4 (82371AB, 82443MX) Power Management Unit
1650 # alpm          Acer Aladdin-IV/V/Pro2 Power Management Unit
1651 # ichiic        Intel generation 4 I2C controller
1652 # ichsmb        Intel ICH SMBus controller chips (82801AA, 82801AB, 82801BA)
1653 # viapm         VIA VT82C586B,596,686A and VT8233 SMBus controllers
1654 # amdpm         AMD 756 Power Management Unit
1655 # amdsmb        AMD 8111 SMBus 2.0 Controller
1657 device          smbus           # Bus support, required for smb below.
1659 device          intpm
1660 device          alpm
1661 device          ichiic
1662 device          ichsmb
1663 device          viapm
1664 device          amdpm
1665 device          amdsmb
1667 device          smb
1669 device          smbacpi
1672 # I2C Bus
1674 # Philips i2c bus support is provided by the `iicbus' device.
1676 # Supported devices:
1677 # ic    i2c network interface
1678 # iic   i2c standard io
1679 # iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
1681 # Supported interfaces:
1682 # pcf   Philips PCF8584 ISA-bus controller
1683 # bktr  brooktree848 I2C software interface
1685 # Other:
1686 # iicbb generic I2C bit-banging code (needed by lpbb, bktr)
1688 device          iicbus          # Bus support, required for ic/iic/iicsmb below.
1689 device          iicbb
1691 device          ic
1692 device          iic
1693 device          iicsmb          # smb over i2c bridge
1695 device          pcf0    at isa? port 0x320 irq 5
1697 # Intel performance-energy bias
1698 device          perfbias
1700 # Intel software controlled clock modulation
1701 device          clockmod
1703 # Intel Sandy Bridge and newer CPUs power usage estimation
1704 device          corepower
1706 # Intel Core and newer CPUs on-die digital thermal sensor support
1707 device          coretemp
1709 # Memory thermal sensor
1710 device          memtemp
1712 # CPU control pseudo-device. Provides access to MSRs, CPUID info and
1713 # microcode update feature.
1714 device          cpuctl
1716 # Effective CPU frequency interface via APERF/MPERF MSRs
1717 device          aperf
1719 # AMD Family 0Fh, 10h and 11h temperature sensors
1720 device          kate
1721 device          km
1723 # ThinkPad Active Protection System accelerometer
1724 device          aps0    at isa? port 0x1600
1726 # HW monitoring devices lm(4), it(4) and nsclpcsio.
1727 device          lm0     at isa? port 0x290
1728 device          it0     at isa? port 0x290
1729 device          it1     at isa? port 0xc00
1730 device          it2     at isa? port 0xd00
1731 device          it3     at isa? port 0x228
1732 device          nsclpcsio0 at isa? port 0x2e
1733 device          nsclpcsio1 at isa? port 0x4e
1734 device          wbsio0  at isa? port 0x2e
1735 device          wbsio1  at isa? port 0x4e
1736 device          uguru0  at isa? port 0xe0       # ABIT uGuru
1738 # EFI Runtime Services support (not functional yet).
1739 options         EFIRT
1741 # Parallel-Port Bus
1743 # Parallel port bus support is provided by the `ppbus' device.
1744 # Multiple devices may be attached to the parallel port, devices
1745 # are automatically probed and attached when found.
1747 # Supported devices:
1748 # vpo   Iomega Zip Drive
1749 #       Requires SCSI disk support ('scbus' and 'da'); the best
1750 #       performance is achieved with ports in EPP 1.9 mode.
1751 # lpt   Parallel Printer
1752 # plip  Parallel network interface
1753 # ppi   General-purpose I/O ("Geek Port") + IEEE1284 I/O
1754 # pps   Pulse per second Timing Interface
1755 # lpbb  Philips official parallel port I2C bit-banging interface
1757 # Supported interfaces:
1758 # ppc   ISA-bus parallel port interfaces.
1761 options         PPC_PROBE_CHIPSET # Enable chipset specific detection
1762                                   # (see flags in ppc(4))
1763 options         DEBUG_1284      # IEEE1284 signaling protocol debug
1764 options         PERIPH_1284     # Makes your computer act as a IEEE1284
1765                                 # compliant peripheral
1766 options         DONTPROBE_1284  # Avoid boot detection of PnP parallel devices
1767 options         VP0_DEBUG       # ZIP/ZIP+ debug
1768 options         LPT_DEBUG       # Printer driver debug
1769 options         PPC_DEBUG=2     # Parallel chipset level debug
1770 options         PLIP_DEBUG      # Parallel network IP interface debug
1771 options         PCFCLOCK_VERBOSE         # Verbose pcfclock driver
1772 options         PCFCLOCK_MAX_RETRIES=5   # Maximum read tries (default 10)
1774 device          ppc0    at isa? irq 7
1775 device          ppbus
1776 device          vpo
1777 device          lpt
1778 device          plip
1779 device          ppi
1780 device          pps
1781 device          lpbb
1782 device          pcfclock
1784 # Kernel BOOTP support
1786 options         BOOTP           # Use BOOTP to obtain IP address/hostname
1787 options         BOOTP_NFSROOT   # NFS mount root filesystem using BOOTP info
1788 options         BOOTP_COMPAT    # Workaround for broken bootp daemons.
1789 options         BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
1792 # Set the number of PV entries per process.  Increasing this can
1793 # stop panics related to heavy use of shared memory. However, that can
1794 # (combined with large amounts of physical memory) cause panics at
1795 # boot time due the kernel running out of VM space.
1797 # If you're tweaking this, you might also want to increase the sysctls
1798 # "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
1800 # The value below is the one more than the default.
1802 options         PMAP_SHPGPERPROC=201
1805 # Disable swapping. This option removes all code which actually performs
1806 # swapping, so it's not possible to turn it back on at run-time.
1808 # This is sometimes usable for systems which don't have any swap space
1809 # (see also sysctls "vm.defer_swapspace_pageouts" and
1810 # "vm.disable_swapspace_pageouts")
1812 #options        NO_SWAPPING
1814 # Set the size of the buffer cache KVM reservation, in buffers.  This is
1815 # scaled by approximately 16384 bytes.  The system will auto-size the buffer
1816 # cache if this option is not specified.
1818 options         NBUF=512
1820 # Set the size of the mbuf KVM reservation, in clusters.  This is scaled
1821 # by approximately 2048 bytes.  The system will auto-size the mbuf area
1822 # to (512 + maxusers*16) if this option is not specified.
1823 # maxusers is in turn computed at boot time depending on available memory
1824 # or set to the value specified by "options MAXUSERS=x" (x=0 means
1825 # autoscaling).
1826 # So, to take advantage of autoscaling, you have to remove both
1827 # NMBCLUSTERS and MAXUSERS (and NMBUFS) from your kernel config.
1829 options         NMBCLUSTERS=1024
1831 # Set the number of mbufs available in the system. Each mbuf
1832 # consumes 256 bytes. The system will autosize this (to 4 times
1833 # the number of NMBCLUSTERS, depending on other constraints)
1834 # if this option is not specified.
1836 options         NMBUFS=4096
1838 # Tune the buffer cache maximum KVA reservation, in bytes.  The maximum is
1839 # usually capped at 200 MB, effecting machines with > 1GB of ram.  Note
1840 # that the buffer cache only really governs write buffering and disk block
1841 # translations.  The VM page cache is our primary disk cache and is not
1842 # effected by the size of the buffer cache.
1844 options         VM_BCACHE_SIZE_MAX="(100*1024*1024)"
1846 # Tune the swap zone KVA reservation, in bytes.  The default is typically
1847 # 70 MB, giving the system the ability to manage a maximum of 28GB worth
1848 # of swapped out data.
1850 options         VM_SWZONE_SIZE_MAX="(50*1024*1024)"
1853 # Enable extra debugging code for locks.  This stores the filename and
1854 # line of whatever acquired the lock in the lock itself, and change a
1855 # number of function calls to pass around the relevant data.  This is
1856 # not at all useful unless you are debugging lock code.  Also note
1857 # that it is likely to break e.g. fstat(1) unless you recompile your
1858 # userland with -DDEBUG_LOCKS as well.
1860 # DEBUG_LOCKS_LATENCY adds a sysctl to add a forced latency loop
1861 # (count to N) in front of any spinlock or gettoken.
1863 options         DEBUG_LOCKS
1864 options         DEBUG_LOCKS_LATENCY
1866 # Set the amount of time (in seconds) the system will wait before
1867 # rebooting automatically when a kernel panic occurs.  If set to (-1),
1868 # the system will wait indefinitely until a key is pressed on the
1869 # console.
1870 options         PANIC_REBOOT_WAIT_TIME=16
1872 # Attempt to bypass the buffer cache and put data directly into the
1873 # userland buffer for read operation when O_DIRECT flag is set on the
1874 # file.  Both offset and length of the read operation must be
1875 # multiples of the physical media sector size.
1877 options         DIRECTIO
1879 # Specify a lower limit for the number of swap I/O buffers.  They are
1880 # (among other things) used when bypassing the buffer cache due to
1881 # DIRECTIO kernel option enabled and O_DIRECT flag set on file.
1883 #options                NSWBUF_MIN=120
1885 # The 'asr' driver provides support for current DPT/Adaptec SCSI RAID
1886 # controllers (SmartRAID V and VI and later).
1887 # These controllers require the CAM infrastructure.
1889 device          asr
1891 # The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
1892 # These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
1893 # The DPT controllers are commonly re-licensed under other brand-names -
1894 # some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
1895 # Compaq are actually DPT controllers.
1897 # See src/sys/dev/raid/dpt for debugging and other subtle options.
1898 #   DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
1899 #                           instruments are enabled.  The tools in
1900 #                           /usr/sbin/dpt_* assume these to be enabled.
1901 #   DPT_HANDLE_TIMEOUTS     Normally device timeouts are handled by the DPT.
1902 #                           If you ant the driver to handle timeouts, enable
1903 #                           this option.  If your system is very busy, this
1904 #                           option will create more trouble than solve.
1905 #   DPT_TIMEOUT_FACTOR      Used to compute the excessive amount of time to
1906 #                           wait when timing out with the above option.
1907 #  DPT_DEBUG_xxxx           These are controllable from sys/dev/raid/dpt/dpt.h
1908 #  DPT_LOST_IRQ             When enabled, will try, once per second, to catch
1909 #                           any interrupt that got lost.  Seems to help in some
1910 #                           DPT-firmware/Motherboard combinations.  Minimal
1911 #                           cost, great benefit.
1912 #  DPT_RESET_HBA            Make "reset" actually reset the controller
1913 #                           instead of fudging it.  Only enable this if you
1914 #                           are 100% certain you need it.
1916 device          dpt
1918 # DPT options
1919 #!CAM# options  DPT_MEASURE_PERFORMANCE
1920 #!CAM# options  DPT_HANDLE_TIMEOUTS
1921 options         DPT_TIMEOUT_FACTOR=4
1922 options         DPT_LOST_IRQ
1923 options         DPT_RESET_HBA
1926 # Compaq "CISS" RAID controllers (SmartRAID 5* series)
1927 # These controllers have a SCSI-like interface, and require the
1928 # CAM infrastructure.
1930 device          ciss
1933 # Intel Integrated RAID controllers.
1934 # This driver is supported and maintained by
1935 # "Leubner, Achim" <Achim_Leubner@adaptec.com>.
1937 device          iir
1940 # Mylex AcceleRAID and eXtremeRAID controllers with v6 and later
1941 # firmware.  These controllers have a SCSI-like interface, and require
1942 # the CAM infrastructure.
1944 device          mly
1946 # USB support
1949 # UHCI controller
1950 device          uhci
1951 # OHCI controller
1952 device          ohci
1953 # EHCI controller
1954 device          ehci
1955 # XHCI controller
1956 device          xhci
1957 # General USB code (mandatory for USB)
1958 device          usb
1959 # Human Interface Device (anything with buttons and dials)
1960 device          uhid
1961 # USB keyboard
1962 device          ukbd
1963 # USB printer
1964 device          ulpt
1965 # USB mass storage (Requires scbus and da)
1966 device          umass
1967 # USB mass storage driver for device-side mode
1968 device          usfs
1969 # USB modem support
1970 device          umodem
1971 # USB mouse
1972 device          ums
1973 # eGalax USB touch screen
1974 device          uep
1975 # Diamond Rio 500 MP3 player
1976 device          urio
1977 # USB com devices
1978 device          "u3g"
1979 device          uark
1980 device          ubsa
1981 device          ubser
1982 device          uchcom
1983 device          ucom
1984 device          ucycom
1985 device          ufoma
1986 device          uftdi
1987 device          ugensa
1988 device          uipaq
1989 device          umcs
1990 device          umct
1991 device          umoscom
1992 device          uplcom
1993 device          uslcom
1994 device          uvisor
1995 device          uvscom
1998 # USB ethernet support
1999 device          uether
2001 # ADMtek USB ethernet. Supports the LinkSys USB100TX,
2002 # the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
2003 # and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
2004 # eval board.
2005 device          aue
2007 # ASIX Electronics AX88172 USB 2.0 ethernet driver. Used in the
2008 # LinkSys USB200M and various other adapters.
2009 device          axe
2011 # ASIX Electronics AX88178A/AX88179 USB 2.0/3.0 gigabit ethernet driver.
2012 device          axge
2014 # CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
2015 # and Netmate II, and the Belkin F5U111.
2016 device          cue
2018 # USB Apple iPhone/iPad tethered Ethernet driver
2019 device          ipheth
2021 # Kawasaki LSI ethernet. Supports the LinkSys USB10T,
2022 # Entrega USB-NET-E45, Peracom Ethernet Adapter, the
2023 # 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
2024 # the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
2025 # and 2104USB, and the Corega USB-T.
2026 device          kue
2028 # Moschip MCS7730/MCS7840 USB to fast ethernet. Supports the Sitecom LN030.
2029 device          mos
2031 # Davicom DM9601E USB to fast ethernet. Supports the Corega FEther USB-TXC.
2032 device          udav
2034 # USB wireless NICs, requires wlan_amrr
2036 # Ralink Technology RT2501USB/RT2601USB
2037 device          rum
2039 # Ralink Technology RT2700U/RT2800U/RT3000U wireless driver
2040 device          run
2041 device          runfw
2043 # RNDIS USB ethernet driver
2044 device          urndis
2046 # Realtek RTL8188CU/RTL8192CU wireless driver
2047 device          urtwn
2048 device          urtwnfw
2049 options         URTWN_WITHOUT_UCODE
2051 # Fm Radio
2053 device          ufm
2055 # Templates for programming USB device side drivers
2057 device          usb_template
2059 # debugging options for the USB subsystem
2061 options         USB_DEBUG
2063 # options for ukbd:
2064 options         UKBD_DFLT_KEYMAP        # specify the built-in keymap
2065 makeoptions     UKBD_DFLT_KEYMAP=it.iso
2067 # Firewire support
2068 device          firewire        # Firewire bus code
2069 device          sbp             # SCSI over Firewire (Requires scbus and da)
2070 device          fwe             # Ethernet over Firewire (non-standard!)
2072 # dcons support (Dumb Console Device)
2073 device          dcons                   # dumb console driver
2074 device          dcons_crom              # FireWire attachment
2075 options         DCONS_BUF_SIZE=16384    # buffer size
2076 options         DCONS_POLL_HZ=100       # polling rate
2077 options         DCONS_FORCE_CONSOLE=1   # force to be the primary console
2078 options         DCONS_FORCE_GDB=1       # force to be the gdb device
2080 #####################################################################
2081 # crypto subsystem
2083 # This is a port of the openbsd crypto framework.  Include this when
2084 # configuring IPsec and when you have a h/w crypto device to accelerate
2085 # user applications that link to openssl.
2087 # Drivers are ports from openbsd with some simple enhancements that have
2088 # been fed back to openbsd (and hopefully will be included).
2090 device          crypto          # core crypto support
2091 device          cryptodev       # /dev/crypto for access to h/w
2093 device          rndtest         # FIPS 140-2 entropy tester
2095 device          hifn            # Hifn 7951, 7781, etc.
2096 options         HIFN_DEBUG      # enable debugging support: hw.hifn.debug
2097 #options        HIFN_NO_RNG     # for devices without RNG
2098 options         HIFN_RNDTEST    # enable rndtest support
2100 device          safe            # SafeNet 1141
2101 options         SAFE_DEBUG      # enable debugging support: hw.safe.debug
2102 #options        SAFE_NO_RNG     # for devices without RNG
2103 options         SAFE_RNDTEST    # enable rndtest support
2105 device          ubsec           # Broadcom 5501, 5601, 58xx
2106 options         UBSEC_DEBUG     # enable debugging support: hw.ubsec.debug
2107 #options        UBSEC_NO_RNG    # for devices without RNG
2108 options         UBSEC_RNDTEST   # enable rndtest support
2110 device          aesni           # hardware crypto/RNG for AES-NI
2111 device          padlock         # hardware crypto/RNG for VIA C3/C7/Eden
2112 device          rdrand          # hardware RNG for RdRand
2115 # ACPI support using the Intel ACPI Component Architecture reference
2116 # implementation.
2118 # ACPI_DEBUG enables the use of the debug.acpi.level and debug.acpi.layer
2119 # kernel environment variables to select initial debugging levels for the
2120 # Intel ACPICA code.
2122 # Note that building ACPI into the kernel is deprecated; the module is
2123 # normally loaded automatically by the loader.
2125 device          acpi
2126 options         ACPI_DEBUG
2128 # ACPI WMI Mapping driver
2129 device          acpi_wmi
2131 # ACPI Asus Extras (LCD backlight/brightness, video output, etc.)
2132 device          acpi_asus
2134 # ACPI Fujitsu Extras (Buttons)
2135 device          acpi_fujitsu
2137 # ACPI extras driver for HP laptops
2138 device          acpi_hp
2140 # ACPI Panasonic Extras (LCD backlight/brightness, video output, etc.)
2141 device          acpi_panasonic
2143 # ACPI pvpanic driver for virtual machines running in Qemu
2144 device          acpi_pvpanic
2146 # ACPI Sony extra (LCD brightness)
2147 device          acpi_sony
2149 # ACPI extras driver for ThinkPad laptops
2150 device          acpi_thinkpad
2152 # ACPI Toshiba Extras (LCD backlight/brightness, video output, etc.)
2153 device          acpi_toshiba
2155 # ACPI Video Extensions (LCD backlight/brightness, video output, etc.)
2156 device          acpi_video
2158 # ACPI Docking Station
2159 device          acpi_dock
2161 device          aibs            # ASUSTeK AI Booster (ACPI ASOC ATK0110)
2163 # DRM options:
2164 # drm:          General DRM code
2165 # i915:         Intel integrated GPUs, starting from the 830M family
2166 # radeon:       ATI/AMD Radeon cards
2168 # DRM_DEBUG:    include debug printfs, very slow
2170 # DRM requires AGP in the kernel.
2172 # Also you'll need to have the following 3 lines in the kernel config.
2173 #       device acpi
2174 #       device iicbus
2175 #       device iicbb
2177 device          drm
2179 # For testing and debugging.
2180 device          "i915"
2181 device          radeon
2183 options         DRM_DEBUG
2184 options         DRM_LINUX
2187 # Misc devices
2189 device          cmx             # Omnikey CardMan 4040 smartcard reader
2190 device          amdsbwd         # AMD South Bridge watchdog
2191 device          gpio            # Enable support for the gpio framework
2192 device          ichwd           # Intel ICH watchdog interrupt timer
2193 device          tbridge         # regression testing
2196 # Virtio support
2198 device          virtio
2199 device          virtio_blk
2200 device          vtnet
2201 device          virtio_pci
2204 # Gpio support for ACPI based SoC platforms
2206 device          gpio_acpi
2207 device          gpio_intel      # GPIO support for Intel SoCs
2210 # Embedded system options:
2212 # An embedded system might want to run something other than init.
2213 options         INIT_PATH="/sbin/init:/sbin/oinit"
2215 # Debug options
2216 options         BUS_DEBUG       # enable newbus debugging
2217 options         RSS_DEBUG       # enable RSS (Receive Side Scaling) debugging
2219 # Record the program counter of the code interrupted by the statistics
2220 # clock interrupt.  Use pctrack(8) to dump this information.
2221 options         DEBUG_PCTRACK
2223 # More undocumented options for linting.
2224 # Note that documenting these are not considered an affront.
2226 #options        ACPI_NO_SEMAPHORES
2227 options         AHC_DUMP_EEPROM
2228 #options        BKTR_ALLOC_PAGES=xxx
2229 options         CAM_DEBUG_DELAY
2230 options         CLUSTERDEBUG
2231 options         DEBUG
2232 options         DEBUG_CRIT_SECTIONS
2233 #options        DISABLE_PSE
2234 options         BCE_RSS_DEBUG
2235 options         BCE_TSS_DEBUG
2236 options         BNX_RSS_DEBUG
2237 options         BNX_TSO_DEBUG
2238 options         BNX_TSS_DEBUG
2239 options         EMX_RSS_DEBUG
2240 options         EMX_TSO_DEBUG
2241 options         EMX_TSS_DEBUG
2242 options         JME_RSS_DEBUG
2243 options         IGB_RSS_DEBUG
2244 options         IGB_TSS_DEBUG
2245 options         IGB_MSIX_DEBUG
2246 options         IX_RSS_DEBUG
2247 options         ENABLE_ALART
2248 options         FB_DEBUG=2
2249 options         FB_INSTALL_CDEV
2250 #options        IEEE80211_DEBUG_REFCNT
2251 options         IEEE80211_SUPPORT_SUPERG
2252 options         KBDIO_DEBUG=10
2253 options         KBD_MAXRETRY=4
2254 options         KBD_MAXWAIT=6
2255 options         KBD_RESETDELAY=201
2256 #options        KERN_TIMESTAMP
2257 options         KEY
2258 #options        LINPROCFS
2259 options         LOCKF_DEBUG
2260 #options        MAXFILES=xxx
2261 options         MBUF_DEBUG
2262 options         NO_LWKT_SPLIT_USERPRI
2263 options         PANIC_DEBUG
2264 options         PMAP_DEBUG
2265 options         PSM_DEBUG=4
2266 options         SCSI_NCR_DEBUG
2267 options         SCSI_NCR_MAX_SYNC=10000
2268 options         SCSI_NCR_MAX_WIDE=1
2269 options         SCSI_NCR_MYADDR=7
2270 options         SHOW_BUSYBUFS   # List buffers that prevent root unmount
2271 options         SI_DEBUG
2272 options         SLAB_DEBUG
2273 options         SOCKBUF_DEBUG
2274 options         TDMA_BINTVAL_DEFAULT=5
2275 options         TDMA_SLOTCNT_DEFAULT=2
2276 options         TDMA_SLOTLEN_DEFAULT=10*1000
2277 options         TDMA_TXRATE_11A_DEFAULT=2*24
2278 options         TDMA_TXRATE_11B_DEFAULT=2*11
2279 options         TDMA_TXRATE_11G_DEFAULT=2*24
2280 options         TDMA_TXRATE_11NA_DEFAULT="(4|IEEE80211_RATE_MCS)"
2281 options         TDMA_TXRATE_11NG_DEFAULT="(4|IEEE80211_RATE_MCS)"
2282 options         TDMA_TXRATE_HALF_DEFAULT=2*12
2283 options         TDMA_TXRATE_QUARTER_DEFAULT=2*6
2284 options         TDMA_TXRATE_TURBO_DEFAULT=2*24
2285 #options        TIMER_FREQ="((14318182+6)/12)"
2286 options         VFS_BIO_DEBUG
2287 options         VM_PAGE_DEBUG
2288 options         XBONEHACK
2290 options KTR
2291 options KTR_ALL
2292 options KTR_ENTRIES=1024
2293 options KTR_VERBOSE=1
2294 #options KTR_ACPI_EC
2295 #options KTR_CTXSW
2296 #options KTR_DMCRYPT
2297 #options KTR_ETHERNET
2298 #options KTR_HAMMER
2299 #options KTR_IFQ
2300 #options KTR_IF_BGE
2301 #options KTR_IF_EM
2302 #options KTR_IF_EMX
2303 #options KTR_IF_POLL
2304 #options KTR_IF_START
2305 #options KTR_IPIQ
2306 #options KTR_KERNENTRY
2307 #options KTR_MEMORY
2308 #options KTR_SERIALIZER
2309 #options KTR_SOWAKEUP
2310 #options KTR_SPIN_CONTENTION
2311 #options KTR_TESTLOG
2312 #options KTR_TOKENS
2313 #options KTR_TSLEEP
2314 #options KTR_UDP
2315 #options KTR_USCHED_BSD4
2316 #options KTR_USCHED_DFLY
2318 # ALTQ
2319 options         ALTQ            #alternate queueing
2320 options         ALTQ_CBQ        #class based queueing
2321 options         ALTQ_RED        #random early detection
2322 options         ALTQ_RIO        #triple red for diffserv (needs RED)
2323 options         ALTQ_HFSC       #hierarchical fair service curve
2324 options         ALTQ_PRIQ       #priority queue
2325 options         ALTQ_FAIRQ      #fair queue
2326 #options        ALTQ_NOPCC      #don't use processor cycle counter
2327 options         ALTQ_DEBUG      #for debugging
2328 # you might want to set kernel timer to 1kHz if you use CBQ,
2329 # especially with 100baseT
2330 #options        HZ=1000
2332 # WATCHDOG
2333 options         WDOG_DISABLE_ON_PANIC   # Automatically disable watchdogs on panic
2335 # LED
2336 options         ERROR_LED_ON_PANIC      # If an error led is present, light it up on panic