contrib/gdb-6.2.1/gdb/serial.h

   1 /* Remote serial support interface definitions for GDB, the GNU Debugger.
   2    Copyright 1992, 1993, 1994, 1995, 1996, 1998, 1999, 2000
   3    Free Software Foundation, Inc.
   4
   5    This file is part of GDB.
   6
   7    This program is free software; you can redistribute it and/or modify
   8    it under the terms of the GNU General Public License as published by
   9    the Free Software Foundation; either version 2 of the License, or
  10    (at your option) any later version.
  11
  12    This program is distributed in the hope that it will be useful,
  13    but WITHOUT ANY WARRANTY; without even the implied warranty of
  14    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  15    GNU General Public License for more details.
  16
  17    You should have received a copy of the GNU General Public License
  18    along with this program; if not, write to the Free Software
  19    Foundation, Inc., 59 Temple Place - Suite 330,
  20    Boston, MA 02111-1307, USA.  */
  21
  22 #ifndef SERIAL_H
  23 #define SERIAL_H
  24
  25 struct ui_file;
  26
  27 /* For most routines, if a failure is indicated, then errno should be
  28    examined.  */
  29
  30 /* Terminal state pointer.  This is specific to each type of
  31    interface. */
  32
  33 typedef void *serial_ttystate;
  34 struct serial;
  35
  36 /* Try to open NAME.  Returns a new `struct serial *' on success, NULL
  37    on failure. Note that some open calls can block and, if possible,
  38    should be  written to be non-blocking, with calls to ui_look_hook
  39    so they can be cancelled. An async interface for open could be
  40    added to GDB if necessary. */
  41
  42 extern struct serial *serial_open (const char *name);
  43
  44 /* Open a new serial stream using a file handle.  */
  45
  46 extern struct serial *serial_fdopen (const int fd);
  47
  48 /* Push out all buffers, close the device and destroy SCB. */
  49
  50 extern void serial_close (struct serial *scb);
  51
  52 /* Push out all buffers and destroy SCB without closing the device.  */
  53
  54 extern void serial_un_fdopen (struct serial *scb);
  55
  56 /* Read one char from the serial device with TIMEOUT seconds to wait
  57    or -1 to wait forever.  Use timeout of 0 to effect a poll.
  58    Infinite waits are not permitted. Returns unsigned char if ok, else
  59    one of the following codes.  Note that all error return-codes are
  60    guaranteed to be < 0. */
  61
  62 enum serial_rc {
  63   SERIAL_ERROR = -1,    /* General error. */
  64   SERIAL_TIMEOUT = -2,  /* Timeout or data-not-ready during read.
  65                            Unfortunately, through
  66                            deprecated_ui_loop_hook(), this can also be
  67                            a QUIT indication.  */
  68   SERIAL_EOF = -3       /* General end-of-file or remote target
  69                            connection closed, indication.  Includes
  70                            things like the line dropping dead. */
  71 };
  72
  73 extern int serial_readchar (struct serial *scb, int timeout);
  74
  75 /* Write LEN chars from STRING to the port SCB.  Returns 0 for
  76    success, non-zero for failure.  */
  77
  78 extern int serial_write (struct serial *scb, const char *str, int len);
  79
  80 /* Write a printf style string onto the serial port. */
  81
  82 extern void serial_printf (struct serial *desc, const char *,...) ATTR_FORMAT (printf, 2, 3);
  83
  84 /* Allow pending output to drain. */
  85
  86 extern int serial_drain_output (struct serial *);
  87
  88 /* Flush (discard) pending output.  Might also flush input (if this
  89    system can't flush only output).  */
  90
  91 extern int serial_flush_output (struct serial *);
  92
  93 /* Flush pending input.  Might also flush output (if this system can't
  94    flush only input).  */
  95
  96 extern int serial_flush_input (struct serial *);
  97
  98 /* Send a break between 0.25 and 0.5 seconds long.  */
  99
 100 extern int serial_send_break (struct serial *scb);
 101
 102 /* Turn the port into raw mode. */
 103
 104 extern void serial_raw (struct serial *scb);
 105
 106 /* Return a pointer to a newly malloc'd ttystate containing the state
 107    of the tty.  */
 108
 109 extern serial_ttystate serial_get_tty_state (struct serial *scb);
 110
 111 /* Set the state of the tty to TTYSTATE.  The change is immediate.
 112    When changing to or from raw mode, input might be discarded.
 113    Returns 0 for success, negative value for error (in which case
 114    errno contains the error).  */
 115
 116 extern int serial_set_tty_state (struct serial *scb, serial_ttystate ttystate);
 117
 118 /* printf_filtered a user-comprehensible description of ttystate on
 119    the specified STREAM. FIXME: At present this sends output to the
 120    default stream - GDB_STDOUT. */
 121
 122 extern void serial_print_tty_state (struct serial *scb, serial_ttystate ttystate, struct ui_file *);
 123
 124 /* Set the tty state to NEW_TTYSTATE, where OLD_TTYSTATE is the
 125    current state (generally obtained from a recent call to
 126    serial_get_tty_state()), but be careful not to discard any input.
 127    This means that we never switch in or out of raw mode, even if
 128    NEW_TTYSTATE specifies a switch.  */
 129
 130 extern int serial_noflush_set_tty_state (struct serial *scb, serial_ttystate new_ttystate, serial_ttystate old_ttystate);
 131
 132 /* Set the baudrate to the decimal value supplied.  Returns 0 for
 133    success, -1 for failure.  */
 134
 135 extern int serial_setbaudrate (struct serial *scb, int rate);
 136
 137 /* Set the number of stop bits to the value specified.  Returns 0 for
 138    success, -1 for failure.  */
 139
 140 #define SERIAL_1_STOPBITS 1
 141 #define SERIAL_1_AND_A_HALF_STOPBITS 2  /* 1.5 bits, snicker... */
 142 #define SERIAL_2_STOPBITS 3
 143
 144 extern int serial_setstopbits (struct serial *scb, int num);
 145
 146 /* Asynchronous serial interface: */
 147
 148 /* Can the serial device support asynchronous mode? */
 149
 150 extern int serial_can_async_p (struct serial *scb);
 151
 152 /* Has the serial device been put in asynchronous mode? */
 153
 154 extern int serial_is_async_p (struct serial *scb);
 155
 156 /* For ASYNC enabled devices, register a callback and enable
 157    asynchronous mode.  To disable asynchronous mode, register a NULL
 158    callback. */
 159
 160 typedef void (serial_event_ftype) (struct serial *scb, void *context);
 161 extern void serial_async (struct serial *scb, serial_event_ftype *handler, void *context);
 162
 163 /* Provide direct access to the underlying FD (if any) used to
 164    implement the serial device.  This interface is clearly
 165    deprecated. Will call internal_error() if the operation isn't
 166    applicable to the current serial device. */
 167
 168 extern int deprecated_serial_fd (struct serial *scb);
 169
 170 /* Trace/debug mechanism.
 171
 172    serial_debug() enables/disables internal debugging.
 173    serial_debug_p() indicates the current debug state. */
 174
 175 extern void serial_debug (struct serial *scb, int debug_p);
 176
 177 extern int serial_debug_p (struct serial *scb);
 178
 179
 180 /* Details of an instance of a serial object */
 181
 182 struct serial
 183   {
 184     int fd;                     /* File descriptor */
 185     struct serial_ops *ops;     /* Function vector */
 186     void *state;                /* Local context info for open FD */
 187     serial_ttystate ttystate;   /* Not used (yet) */
 188     int bufcnt;                 /* Amount of data remaining in receive
 189                                    buffer.  -ve for sticky errors. */
 190     unsigned char *bufp;        /* Current byte */
 191     unsigned char buf[BUFSIZ];  /* Da buffer itself */
 192     int current_timeout;        /* (ser-unix.c termio{,s} only), last
 193                                    value of VTIME */
 194     int timeout_remaining;      /* (ser-unix.c termio{,s} only), we
 195                                    still need to wait for this many
 196                                    more seconds.  */
 197     char *name;                 /* The name of the device or host */
 198     struct serial *next;        /* Pointer to the next `struct serial *' */
 199     int refcnt;                 /* Number of pointers to this block */
 200     int debug_p;                /* Trace this serial devices operation. */
 201     int async_state;            /* Async internal state. */
 202     void *async_context;        /* Async event thread's context */
 203     serial_event_ftype *async_handler;/* Async event handler */
 204   };
 205
 206 struct serial_ops
 207   {
 208     char *name;
 209     struct serial_ops *next;
 210     int (*open) (struct serial *, const char *name);
 211     void (*close) (struct serial *);
 212     int (*readchar) (struct serial *, int timeout);
 213     int (*write) (struct serial *, const char *str, int len);
 214     /* Discard pending output */
 215     int (*flush_output) (struct serial *);
 216     /* Discard pending input */
 217     int (*flush_input) (struct serial *);
 218     int (*send_break) (struct serial *);
 219     void (*go_raw) (struct serial *);
 220     serial_ttystate (*get_tty_state) (struct serial *);
 221     int (*set_tty_state) (struct serial *, serial_ttystate);
 222     void (*print_tty_state) (struct serial *, serial_ttystate,
 223                              struct ui_file *);
 224     int (*noflush_set_tty_state) (struct serial *, serial_ttystate,
 225                                   serial_ttystate);
 226     int (*setbaudrate) (struct serial *, int rate);
 227     int (*setstopbits) (struct serial *, int num);
 228     /* Wait for output to drain */
 229     int (*drain_output) (struct serial *);
 230     /* Change the serial device into/out of asynchronous mode, call
 231        the specified function when ever there is something
 232        interesting. */
 233     void (*async) (struct serial *scb, int async_p);
 234   };
 235
 236 /* Add a new serial interface to the interface list */
 237
 238 extern void serial_add_interface (struct serial_ops * optable);
 239
 240 /* File in which to record the remote debugging session */
 241
 242 extern void serial_log_command (const char *);
 243
 244 #endif /* SERIAL_H */