src/main/target/stm32f1xx_hal_conf.h

   1 /**
   2   ******************************************************************************
   3   * @file    stm32f1xx_hal_conf.h
   4   * @brief   HAL configuration template file.
   5   ******************************************************************************
   6   * @attention
   7   *
   8   * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
   9   *
  10   * Redistribution and use in source and binary forms, with or without modification,
  11   * are permitted provided that the following conditions are met:
  12   *   1. Redistributions of source code must retain the above copyright notice,
  13   *      this list of conditions and the following disclaimer.
  14   *   2. Redistributions in binary form must reproduce the above copyright notice,
  15   *      this list of conditions and the following disclaimer in the documentation
  16   *      and/or other materials provided with the distribution.
  17   *   3. Neither the name of STMicroelectronics nor the names of its contributors
  18   *      may be used to endorse or promote products derived from this software
  19   *      without specific prior written permission.
  20   *
  21   * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  22   * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  23   * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  24   * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  25   * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  26   * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  27   * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  28   * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  29   * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  30   * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  31   *
  32   ******************************************************************************
  33   */
  34
  35 /* Define to prevent recursive inclusion -------------------------------------*/
  36 #ifndef __STM32F1xx_HAL_CONF_H
  37 #define __STM32F1xx_HAL_CONF_H
  38
  39 #ifdef __cplusplus
  40  extern "C" {
  41 #endif
  42
  43 /* Exported types ------------------------------------------------------------*/
  44 /* Exported constants --------------------------------------------------------*/
  45
  46 /* ########################## Module Selection ############################## */
  47 /**
  48   * @brief This is the list of modules to be used in the HAL driver
  49   */
  50 #define HAL_MODULE_ENABLED
  51 #define HAL_ADC_MODULE_ENABLED
  52 //#define HAL_CAN_MODULE_ENABLED
  53 //#define HAL_CEC_MODULE_ENABLED
  54 #define HAL_CORTEX_MODULE_ENABLED
  55 //#define HAL_CRC_MODULE_ENABLED
  56 //#define HAL_DAC_MODULE_ENABLED
  57 #define HAL_DMA_MODULE_ENABLED
  58 //#define HAL_ETH_MODULE_ENABLED
  59 #define HAL_FLASH_MODULE_ENABLED
  60 #define HAL_GPIO_MODULE_ENABLED
  61 //#define HAL_HCD_MODULE_ENABLED
  62 #define HAL_I2C_MODULE_ENABLED
  63 //#define HAL_I2S_MODULE_ENABLED
  64 //#define HAL_IRDA_MODULE_ENABLED
  65 //#define HAL_IWDG_MODULE_ENABLED
  66 //#define HAL_NAND_MODULE_ENABLED
  67 //#define HAL_NOR_MODULE_ENABLED
  68 //#define HAL_PCCARD_MODULE_ENABLED
  69 #define HAL_PCD_MODULE_ENABLED
  70 #define HAL_PWR_MODULE_ENABLED
  71 #define HAL_RCC_MODULE_ENABLED
  72 //#define HAL_RTC_MODULE_ENABLED
  73 //#define HAL_SD_MODULE_ENABLED
  74 //#define HAL_SMARTCARD_MODULE_ENABLED
  75 #define HAL_SPI_MODULE_ENABLED
  76 //#define HAL_SRAM_MODULE_ENABLED
  77 #define HAL_TIM_MODULE_ENABLED
  78 #define HAL_UART_MODULE_ENABLED
  79 #define HAL_USART_MODULE_ENABLED
  80 //#define HAL_WWDG_MODULE_ENABLED
  81
  82 /* ########################## Oscillator Values adaptation ####################*/
  83 /**
  84   * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
  85   *        This value is used by the RCC HAL module to compute the system frequency
  86   *        (when HSE is used as system clock source, directly or through the PLL).
  87   */
  88 #if !defined  (HSE_VALUE)
  89 #if defined(USE_STM3210C_EVAL)
  90   #define HSE_VALUE    ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */
  91 #else
  92   #define HSE_VALUE    ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
  93 #endif
  94 #endif /* HSE_VALUE */
  95
  96 #if !defined  (HSE_STARTUP_TIMEOUT)
  97   #define HSE_STARTUP_TIMEOUT    ((uint32_t)100)   /*!< Time out for HSE start up, in ms */
  98 #endif /* HSE_STARTUP_TIMEOUT */
  99
 100 /**
 101   * @brief Internal High Speed oscillator (HSI) value.
 102   *        This value is used by the RCC HAL module to compute the system frequency
 103   *        (when HSI is used as system clock source, directly or through the PLL).
 104   */
 105 #if !defined  (HSI_VALUE)
 106   #define HSI_VALUE    ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/
 107 #endif /* HSI_VALUE */
 108
 109 /**
 110   * @brief External Low Speed oscillator (LSE) value.
 111   *        This value is used by the UART, RTC HAL module to compute the system frequency
 112   */
 113 #if !defined  (LSE_VALUE)
 114   #define LSE_VALUE    ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/
 115 #endif /* LSE_VALUE */
 116
 117
 118 #if !defined  (LSE_STARTUP_TIMEOUT)
 119   #define LSE_STARTUP_TIMEOUT    ((uint32_t)5000)   /*!< Time out for LSE start up, in ms */
 120 #endif /* HSE_STARTUP_TIMEOUT */
 121
 122
 123 /* Tip: To avoid modifying this file each time you need to use different HSE,
 124    ===  you can define the HSE value in your toolchain compiler preprocessor. */
 125
 126 /* ########################### System Configuration ######################### */
 127 /**
 128   * @brief This is the HAL system configuration section
 129   */
 130 #define  VDD_VALUE                    ((uint32_t)3300) /*!< Value of VDD in mv */
 131 #define  TICK_INT_PRIORITY            ((uint32_t)0x000F)    /*!< tick interrupt priority */
 132 #define  USE_RTOS                     0
 133 #define  PREFETCH_ENABLE              1
 134
 135 /* ########################## Assert Selection ############################## */
 136 /**
 137   * @brief Uncomment the line below to expanse the "assert_param" macro in the
 138   *        HAL drivers code
 139   */
 140 /*#define USE_FULL_ASSERT    1*/
 141
 142
 143 /* ################## Ethernet peripheral configuration ##################### */
 144
 145 /* Section 1 : Ethernet peripheral configuration */
 146
 147 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
 148 #define MAC_ADDR0   2
 149 #define MAC_ADDR1   0
 150 #define MAC_ADDR2   0
 151 #define MAC_ADDR3   0
 152 #define MAC_ADDR4   0
 153 #define MAC_ADDR5   0
 154
 155 /* Definition of the Ethernet driver buffers size and count */
 156 #define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
 157 #define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
 158 #define ETH_RXBUFNB                    ((uint32_t)8)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
 159 #define ETH_TXBUFNB                    ((uint32_t)4)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
 160
 161 /* Section 2: PHY configuration section */
 162
 163 /* DP83848 PHY Address*/
 164 #define DP83848_PHY_ADDRESS             0x01
 165 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
 166 #define PHY_RESET_DELAY                 ((uint32_t)0x000000FF)
 167 /* PHY Configuration delay */
 168 #define PHY_CONFIG_DELAY                ((uint32_t)0x00000FFF)
 169
 170 #define PHY_READ_TO                     ((uint32_t)0x0000FFFF)
 171 #define PHY_WRITE_TO                    ((uint32_t)0x0000FFFF)
 172
 173 /* Section 3: Common PHY Registers */
 174
 175 #define PHY_BCR                         ((uint16_t)0x00)    /*!< Transceiver Basic Control Register   */
 176 #define PHY_BSR                         ((uint16_t)0x01)    /*!< Transceiver Basic Status Register    */
 177
 178 #define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
 179 #define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
 180 #define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
 181 #define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
 182 #define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
 183 #define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
 184 #define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
 185 #define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
 186 #define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
 187 #define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
 188
 189 #define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
 190 #define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
 191 #define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
 192
 193 /* Section 4: Extended PHY Registers */
 194
 195 #define PHY_SR                          ((uint16_t)0x10)    /*!< PHY status register Offset                      */
 196 #define PHY_MICR                        ((uint16_t)0x11)    /*!< MII Interrupt Control Register                  */
 197 #define PHY_MISR                        ((uint16_t)0x12)    /*!< MII Interrupt Status and Misc. Control Register */
 198
 199 #define PHY_LINK_STATUS                 ((uint16_t)0x0001)  /*!< PHY Link mask                                   */
 200 #define PHY_SPEED_STATUS                ((uint16_t)0x0002)  /*!< PHY Speed mask                                  */
 201 #define PHY_DUPLEX_STATUS               ((uint16_t)0x0004)  /*!< PHY Duplex mask                                 */
 202
 203 #define PHY_MICR_INT_EN                 ((uint16_t)0x0002)  /*!< PHY Enable interrupts                           */
 204 #define PHY_MICR_INT_OE                 ((uint16_t)0x0001)  /*!< PHY Enable output interrupt events              */
 205
 206 #define PHY_MISR_LINK_INT_EN            ((uint16_t)0x0020)  /*!< Enable Interrupt on change of link status       */
 207 #define PHY_LINK_INTERRUPT              ((uint16_t)0x2000)  /*!< PHY link status interrupt mask                  */
 208
 209
 210
 211 /* Includes ------------------------------------------------------------------*/
 212 /**
 213   * @brief Include module's header file
 214   */
 215
 216 #ifdef HAL_RCC_MODULE_ENABLED
 217  #include "stm32f1xx_hal_rcc.h"
 218 #endif /* HAL_RCC_MODULE_ENABLED */
 219
 220 #ifdef HAL_GPIO_MODULE_ENABLED
 221  #include "stm32f1xx_hal_gpio.h"
 222 #endif /* HAL_GPIO_MODULE_ENABLED */
 223
 224 #ifdef HAL_DMA_MODULE_ENABLED
 225   #include "stm32f1xx_hal_dma.h"
 226 #endif /* HAL_DMA_MODULE_ENABLED */
 227
 228 #ifdef HAL_ETH_MODULE_ENABLED
 229   #include "stm32f1xx_hal_eth.h"
 230 #endif /* HAL_ETH_MODULE_ENABLED */
 231
 232 #ifdef HAL_CAN_MODULE_ENABLED
 233  #include "stm32f1xx_hal_can.h"
 234 #endif /* HAL_CAN_MODULE_ENABLED */
 235
 236 #ifdef HAL_CEC_MODULE_ENABLED
 237  #include "stm32f1xx_hal_cec.h"
 238 #endif /* HAL_CEC_MODULE_ENABLED */
 239
 240 #ifdef HAL_CORTEX_MODULE_ENABLED
 241  #include "stm32f1xx_hal_cortex.h"
 242 #endif /* HAL_CORTEX_MODULE_ENABLED */
 243
 244 #ifdef HAL_ADC_MODULE_ENABLED
 245  #include "stm32f1xx_hal_adc.h"
 246 #endif /* HAL_ADC_MODULE_ENABLED */
 247
 248 #ifdef HAL_CRC_MODULE_ENABLED
 249  #include "stm32f1xx_hal_crc.h"
 250 #endif /* HAL_CRC_MODULE_ENABLED */
 251
 252 #ifdef HAL_DAC_MODULE_ENABLED
 253  #include "stm32f1xx_hal_dac.h"
 254 #endif /* HAL_DAC_MODULE_ENABLED */
 255
 256 #ifdef HAL_FLASH_MODULE_ENABLED
 257  #include "stm32f1xx_hal_flash.h"
 258 #endif /* HAL_FLASH_MODULE_ENABLED */
 259
 260 #ifdef HAL_SRAM_MODULE_ENABLED
 261  #include "stm32f1xx_hal_sram.h"
 262 #endif /* HAL_SRAM_MODULE_ENABLED */
 263
 264 #ifdef HAL_NOR_MODULE_ENABLED
 265  #include "stm32f1xx_hal_nor.h"
 266 #endif /* HAL_NOR_MODULE_ENABLED */
 267
 268 #ifdef HAL_I2C_MODULE_ENABLED
 269  #include "stm32f1xx_hal_i2c.h"
 270 #endif /* HAL_I2C_MODULE_ENABLED */
 271
 272 #ifdef HAL_I2S_MODULE_ENABLED
 273  #include "stm32f1xx_hal_i2s.h"
 274 #endif /* HAL_I2S_MODULE_ENABLED */
 275
 276 #ifdef HAL_IWDG_MODULE_ENABLED
 277  #include "stm32f1xx_hal_iwdg.h"
 278 #endif /* HAL_IWDG_MODULE_ENABLED */
 279
 280 #ifdef HAL_PWR_MODULE_ENABLED
 281  #include "stm32f1xx_hal_pwr.h"
 282 #endif /* HAL_PWR_MODULE_ENABLED */
 283
 284 #ifdef HAL_RTC_MODULE_ENABLED
 285  #include "stm32f1xx_hal_rtc.h"
 286 #endif /* HAL_RTC_MODULE_ENABLED */
 287
 288 #ifdef HAL_PCCARD_MODULE_ENABLED
 289  #include "stm32f1xx_hal_pccard.h"
 290 #endif /* HAL_PCCARD_MODULE_ENABLED */
 291
 292 #ifdef HAL_SD_MODULE_ENABLED
 293  #include "stm32f1xx_hal_sd.h"
 294 #endif /* HAL_SD_MODULE_ENABLED */
 295
 296 #ifdef HAL_NAND_MODULE_ENABLED
 297  #include "stm32f1xx_hal_nand.h"
 298 #endif /* HAL_NAND_MODULE_ENABLED */
 299
 300 #ifdef HAL_SPI_MODULE_ENABLED
 301  #include "stm32f1xx_hal_spi.h"
 302 #endif /* HAL_SPI_MODULE_ENABLED */
 303
 304 #ifdef HAL_TIM_MODULE_ENABLED
 305  #include "stm32f1xx_hal_tim.h"
 306 #endif /* HAL_TIM_MODULE_ENABLED */
 307
 308 #ifdef HAL_UART_MODULE_ENABLED
 309  #include "stm32f1xx_hal_uart.h"
 310 #endif /* HAL_UART_MODULE_ENABLED */
 311
 312 #ifdef HAL_USART_MODULE_ENABLED
 313  #include "stm32f1xx_hal_usart.h"
 314 #endif /* HAL_USART_MODULE_ENABLED */
 315
 316 #ifdef HAL_IRDA_MODULE_ENABLED
 317  #include "stm32f1xx_hal_irda.h"
 318 #endif /* HAL_IRDA_MODULE_ENABLED */
 319
 320 #ifdef HAL_SMARTCARD_MODULE_ENABLED
 321  #include "stm32f1xx_hal_smartcard.h"
 322 #endif /* HAL_SMARTCARD_MODULE_ENABLED */
 323
 324 #ifdef HAL_WWDG_MODULE_ENABLED
 325  #include "stm32f1xx_hal_wwdg.h"
 326 #endif /* HAL_WWDG_MODULE_ENABLED */
 327
 328 #ifdef HAL_PCD_MODULE_ENABLED
 329  #include "stm32f1xx_hal_pcd.h"
 330 #endif /* HAL_PCD_MODULE_ENABLED */
 331
 332
 333 #ifdef HAL_HCD_MODULE_ENABLED
 334  #include "stm32f1xx_hal_hcd.h"
 335 #endif /* HAL_HCD_MODULE_ENABLED */
 336
 337
 338 /* Exported macro ------------------------------------------------------------*/
 339 #ifdef  USE_FULL_ASSERT
 340 /**
 341   * @brief  The assert_param macro is used for function's parameters check.
 342   * @param  expr: If expr is false, it calls assert_failed function
 343   *         which reports the name of the source file and the source
 344   *         line number of the call that failed.
 345   *         If expr is true, it returns no value.
 346   * @retval None
 347   */
 348   #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
 349 /* Exported functions ------------------------------------------------------- */
 350   void assert_failed(uint8_t* file, uint32_t line);
 351 #else
 352   #define assert_param(expr) ((void)0)
 353 #endif /* USE_FULL_ASSERT */
 354
 355 #ifdef __cplusplus
 356 }
 357 #endif
 358
 359 #endif /* __STM32F1xx_HAL_CONF_H */
 360
 361
 362 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/