| blob | a483803e8fa204c202329176f367b74f10dc5539 |
1 ;
2 ; Zapata telephony interface
3 ;
4 ; Configuration file
5 ;
6 ; You need to restart Asterisk to re-configure the Zap channel
7 ; CLI> reload chan_zap.so
8 ; will reload the configuration file,
9 ; but not all configuration options are
10 ; re-configured during a reload.
14 [trunkgroups]
15 ;
16 ; Trunk groups are used for NFAS or GR-303 connections.
17 ;
18 ; Group: Defines a trunk group.
19 ; trunkgroup => <trunkgroup>,<dchannel>[,<backup1>...]
20 ;
21 ; trunkgroup is the numerical trunk group to create
22 ; dchannel is the zap channel which will have the
23 ; d-channel for the trunk.
24 ; backup1 is an optional list of backup d-channels.
25 ;
26 ;trunkgroup => 1,24,48
27 ;trunkgroup => 1,24
28 ;
29 ; Spanmap: Associates a span with a trunk group
30 ; spanmap => <zapspan>,<trunkgroup>[,<logicalspan>]
31 ;
32 ; zapspan is the zap span number to associate
33 ; trunkgroup is the trunkgroup (specified above) for the mapping
34 ; logicalspan is the logical span number within the trunk group to use.
35 ; if unspecified, no logical span number is used.
36 ;
37 ;spanmap => 1,1,1
38 ;spanmap => 2,1,2
39 ;spanmap => 3,1,3
40 ;spanmap => 4,1,4
42 [channels]
43 ;
44 ; Default language
45 ;
46 ;language=en
47 ;
48 ; Default context
49 ;
50 context=default
51 ;
52 ; Switchtype: Only used for PRI.
53 ;
54 ; national: National ISDN 2 (default)
55 ; dms100: Nortel DMS100
56 ; 4ess: AT&T 4ESS
57 ; 5ess: Lucent 5ESS
58 ; euroisdn: EuroISDN
59 ; ni1: Old National ISDN 1
60 ; qsig: Q.SIG
61 ;
62 switchtype=national
63 ;
64 ; Some switches (AT&T especially) require network specific facility IE
65 ; supported values are currently 'none', 'sdn', 'megacom', 'tollfreemegacom', 'accunet'
66 ;
67 ;nsf=none
68 ;
69 ; PRI Dialplan: Only RARELY used for PRI.
70 ;
71 ; unknown: Unknown
72 ; private: Private ISDN
73 ; local: Local ISDN
74 ; national: National ISDN
75 ; international: International ISDN
76 ; dynamic: Dynamically selects the appropriate dialplan
77 ;
78 ;pridialplan=national
79 ;
80 ; PRI Local Dialplan: Only RARELY used for PRI (sets the calling number's numbering plan)
81 ;
82 ; unknown: Unknown
83 ; private: Private ISDN
84 ; local: Local ISDN
85 ; national: National ISDN
86 ; international: International ISDN
87 ; dynamic: Dynamically selects the appropriate dialplan
88 ;
89 ;prilocaldialplan=national
90 ;
91 ; PRI callerid prefixes based on the given TON/NPI (dialplan)
92 ; This is especially needed for euroisdn E1-PRIs
93 ;
94 ; sample 1 for Germany
95 ;internationalprefix = 00
96 ;nationalprefix = 0
97 ;localprefix = 0711
98 ;privateprefix = 07115678
99 ;unknownprefix =
100 ;
101 ; sample 2 for Germany
102 ;internationalprefix = +
103 ;nationalprefix = +49
104 ;localprefix = +49711
105 ;privateprefix = +497115678
106 ;unknownprefix =
107 ;
108 ; PRI resetinterval: sets the time in seconds between restart of unused
109 ; channels, defaults to 3600; minimum 60 seconds. Some PBXs don't like
110 ; channel restarts. so set the interval to a very long interval e.g. 100000000
111 ; or 'never' to disable *entirely*.
112 ;
113 ;resetinterval = 3600
114 ;
115 ; Overlap dialing mode (sending overlap digits)
116 ;
117 ;overlapdial=yes
118 ;
119 ; PRI Out of band indications.
120 ; Enable this to report Busy and Congestion on a PRI using out-of-band
121 ; notification. Inband indication, as used by Asterisk doesn't seem to work
122 ; with all telcos.
123 ;
124 ; outofband: Signal Busy/Congestion out of band with RELEASE/DISCONNECT
125 ; inband: Signal Busy/Congestion using in-band tones
126 ;
127 ; priindication = outofband
128 ;
129 ; If you need to override the existing channels selection routine and force all
130 ; PRI channels to be marked as exclusively selected, set this to yes.
131 ; priexclusive = yes
132 ;
133 ; ISDN Timers
134 ; All of the ISDN timers and counters that are used are configurable. Specify
135 ; the timer name, and its value (in ms for timers).
136 ; K: Layer 2 max number of outstanding unacknowledged I frames (default 7)
137 ; N200: Layer 2 max number of retransmissions of a frame (default 3)
138 ; T200: Layer 2 max time before retransmission of a frame (default 1000 ms)
139 ; T203: Layer 2 max time without frames being exchanged (default 10000 ms)
140 ; T305: Wait for DISCONNECT acknowledge (default 30000 ms)
141 ; T308: Wait for RELEASE acknowledge (default 4000 ms)
142 ; T309: Maintain active calls on Layer 2 disconnection (default -1, Asterisk clears calls)
143 ; EuroISDN: 6000 to 12000 ms, according to (N200 + 1) x T200 + 2s
144 ; May vary in other ISDN standards (Q.931 1993 : 90000 ms)
145 ; T313: Wait for CONNECT acknowledge, CPE side only (default 3000 ms)
146 ;
147 ; pritimer => t200,1000
148 ; pritimer => t313,4000
149 ;
150 ; To enable transmission of facility-based ISDN supplementary services (such
151 ; as caller name from CPE over facility), enable this option.
152 ; facilityenable = yes
153 ;
154 ;
155 ; Signalling method (default is fxs). Valid values:
156 ; em: E & M
157 ; em_w: E & M Wink
158 ; featd: Feature Group D (The fake, Adtran style, DTMF)
159 ; featdmf: Feature Group D (The real thing, MF (domestic, US))
160 ; featdmf_ta: Feature Group D (The real thing, MF (domestic, US)) through
161 ; a Tandem Access point
162 ; featb: Feature Group B (MF (domestic, US))
163 ; fgccama Feature Group C-CAMA (DP DNIS, MF ANI)
164 ; fgccamamf Feature Group C-CAMA MF (MF DNIS, MF ANI)
165 ; fxs_ls: FXS (Loop Start)
166 ; fxs_gs: FXS (Ground Start)
167 ; fxs_ks: FXS (Kewl Start)
168 ; fxo_ls: FXO (Loop Start)
169 ; fxo_gs: FXO (Ground Start)
170 ; fxo_ks: FXO (Kewl Start)
171 ; pri_cpe: PRI signalling, CPE side
172 ; pri_net: PRI signalling, Network side
173 ; gr303fxoks_net: GR-303 Signalling, FXO Loopstart, Network side
174 ; gr303fxsks_cpe: GR-303 Signalling, FXS Loopstart, CPE side
175 ; sf: SF (Inband Tone) Signalling
176 ; sf_w: SF Wink
177 ; sf_featd: SF Feature Group D (The fake, Adtran style, DTMF)
178 ; sf_featdmf: SF Feature Group D (The real thing, MF (domestic, US))
179 ; sf_featb: SF Feature Group B (MF (domestic, US))
180 ; e911: E911 (MF) style signalling
181 ;
182 ; The following are used for Radio interfaces:
183 ; fxs_rx: Receive audio/COR on an FXS kewlstart interface (FXO at the
184 ; channel bank)
185 ; fxs_tx: Transmit audio/PTT on an FXS loopstart interface (FXO at the
186 ; channel bank)
187 ; fxo_rx: Receive audio/COR on an FXO loopstart interface (FXS at the
188 ; channel bank)
189 ; fxo_tx: Transmit audio/PTT on an FXO groundstart interface (FXS at
190 ; the channel bank)
191 ; em_rx: Receive audio/COR on an E&M interface (1-way)
192 ; em_tx: Transmit audio/PTT on an E&M interface (1-way)
193 ; em_txrx: Receive audio/COR AND Transmit audio/PTT on an E&M interface
194 ; (2-way)
195 ; em_rxtx: Same as em_txrx (for our dyslexic friends)
196 ; sf_rx: Receive audio/COR on an SF interface (1-way)
197 ; sf_tx: Transmit audio/PTT on an SF interface (1-way)
198 ; sf_txrx: Receive audio/COR AND Transmit audio/PTT on an SF interface
199 ; (2-way)
200 ; sf_rxtx: Same as sf_txrx (for our dyslexic friends)
201 ;
202 signalling=fxo_ls
203 ;
204 ; If you have an outbound signalling format that is different from format
205 ; specified above (but compatible), you can specify outbound signalling format,
206 ; (see below). The 'signalling' format specified will be the inbound signalling
207 ; format. If you only specify 'signalling', then it will be the format for
208 ; both inbound and outbound.
209 ;
210 ; signalling=featdmf
211 ; outsignalling=featb
212 ;
213 ; For Feature Group D Tandem access, to set the default CIC and OZZ use these
214 ; parameters:
215 ;defaultozz=0000
216 ;defaultcic=303
217 ;
218 ; A variety of timing parameters can be specified as well
219 ; Including:
220 ; prewink: Pre-wink time (default 50ms)
221 ; preflash: Pre-flash time (default 50ms)
222 ; wink: Wink time (default 150ms)
223 ; flash: Flash time (default 750ms)
224 ; start: Start time (default 1500ms)
225 ; rxwink: Receiver wink time (default 300ms)
226 ; rxflash: Receiver flashtime (default 1250ms)
227 ; debounce: Debounce timing (default 600ms)
228 ;
229 rxwink=300 ; Atlas seems to use long (250ms) winks
230 ;
231 ; How long generated tones (DTMF and MF) will be played on the channel
232 ; (in milliseconds)
233 ;toneduration=100
234 ;
235 ; Whether or not to do distinctive ring detection on FXO lines
236 ;
237 ;usedistinctiveringdetection=yes
238 ;distinctiveringaftercid=yes ; enable dring detection after callerid for those countries like Australia
239 ; where the ring cadence is changed *after* the callerid spill.
240 ;
241 ; Whether or not to use caller ID
242 ;
243 usecallerid=yes
244 ;
245 ; Type of caller ID signalling in use
246 ; bell = bell202 as used in US
247 ; v23 = v23 as used in the UK
248 ; v23_jp = v23 as used in Japan
249 ; dtmf = DTMF as used in Denmark, Sweden and Netherlands
250 ; smdi = Use SMDI for callerid. Requires SMDI to be enabled (usesmdi).
251 ;
252 ;cidsignalling=bell
253 ;
254 ; What signals the start of caller ID
255 ; ring = a ring signals the start
256 ; polarity = polarity reversal signals the start
257 ;
258 ;cidstart=ring
259 ;
260 ; Whether or not to hide outgoing caller ID (Override with *67 or *82)
261 ;
262 hidecallerid=no
263 ;
264 ; Whether or not to enable call waiting on internal extensions
265 ; With this set to 'yes', busy extensions will hear the call-waiting
266 ; tone, and can use hook-flash to switch between callers. The Dial()
267 ; app will not return the "BUSY" result for extensions.
268 ;
269 callwaiting=yes
270 ;
271 ; Whether or not restrict outgoing caller ID (will be sent as ANI only, not
272 ; available for the user)
273 ; Mostly use with FXS ports
274 ;
275 ;restrictcid=no
276 ;
277 ; Whether or not use the caller ID presentation for the outgoing call that the
278 ; calling switch is sending.
279 ; See README.callingpres
280 ;
281 usecallingpres=yes
282 ;
283 ; Some countries (UK) have ring tones with different ring tones (ring-ring),
284 ; which means the callerid needs to be set later on, and not just after
285 ; the first ring, as per the default.
286 ;
287 ;sendcalleridafter=1
288 ;
289 ;
290 ; Support Caller*ID on Call Waiting
291 ;
292 callwaitingcallerid=yes
293 ;
294 ; Support three-way calling
295 ;
296 threewaycalling=yes
297 ;
298 ; For FXS ports (either direct analog or over T1/E1):
299 ; Support flash-hook call transfer (requires three way calling)
300 ; Also enables call parking (overrides the 'canpark' parameter)
301 ;
302 ; For digital ports using ISDN PRI protocols:
303 ; Support switch-side transfer (called 2BCT, RLT or other names)
304 ; This setting must be enabled on both ports involved, and the
305 ; 'facilityenable' setting must also be enabled to allow sending
306 ; the transfer to the ISDN switch, since it sent in a FACILITY
307 ; message.
308 ;
309 transfer=yes
310 ;
311 ; Allow call parking
312 ; ('canpark=no' is overridden by 'transfer=yes')
313 ;
314 canpark=yes
315 ;
316 ; Support call forward variable
317 ;
318 cancallforward=yes
319 ;
320 ; Whether or not to support Call Return (*69)
321 ;
322 callreturn=yes
323 ;
324 ; Stutter dialtone support: If a mailbox is specified without a voicemail
325 ; context, then when voicemail is received in a mailbox in the default
326 ; voicemail context in voicemail.conf, taking the phone off hook will cause a
327 ; stutter dialtone instead of a normal one.
328 ;
329 ; If a mailbox is specified *with* a voicemail context, the same will result
330 ; if voicemail received in mailbox in the specified voicemail context.
331 ;
332 ; for default voicemail context, the example below is fine:
333 ;
334 ;mailbox=1234
335 ;
336 ; for any other voicemail context, the following will produce the stutter tone:
337 ;
338 ;mailbox=1234@context
339 ;
340 ; Enable echo cancellation
341 ; Use either "yes", "no", or a power of two from 32 to 256 if you wish to
342 ; actually set the number of taps of cancellation.
343 ;
344 ; Note that when setting the number of taps, the number 256 does not translate
345 ; to 256 ms of echo cancellation. echocancel=256 means 256 / 8 = 32 ms.
346 ;
347 ; Note that if any of your Zaptel cards have hardware echo cancellers,
348 ; then this setting only turns them on and off; numeric settings will
349 ; be treated as "yes". There are no special settings required for
350 ; hardware echo cancellers; when present and enabled in their kernel
351 ; modules, they take precedence over the software echo canceller compiled
352 ; into Zaptel automatically.
353 ;
354 echocancel=yes
355 ;
356 ; Generally, it is not necessary (and in fact undesirable) to echo cancel when
357 ; the circuit path is entirely TDM. You may, however, change this behavior
358 ; by enabling the echo cancel during pure TDM bridging below.
359 ;
360 echocancelwhenbridged=yes
361 ;
362 ; In some cases, the echo canceller doesn't train quickly enough and there
363 ; is echo at the beginning of the call. Enabling echo training will cause
364 ; asterisk to briefly mute the channel, send an impulse, and use the impulse
365 ; response to pre-train the echo canceller so it can start out with a much
366 ; closer idea of the actual echo. Value may be "yes", "no", or a number of
367 ; milliseconds to delay before training (default = 400)
368 ;
369 ; WARNING: In some cases this option can make echo worse! If you are
370 ; trying to debug an echo problem, it is worth checking to see if your echo
371 ; is better with the option set to yes or no. Use whatever setting gives
372 ; the best results.
373 ;
374 ; Note that these parameters do not apply to hardware echo cancellers.
375 ;
376 ;echotraining=yes
377 ;echotraining=800
378 ;
379 ; If you are having trouble with DTMF detection, you can relax the DTMF
380 ; detection parameters. Relaxing them may make the DTMF detector more likely
381 ; to have "talkoff" where DTMF is detected when it shouldn't be.
382 ;
383 ;relaxdtmf=yes
384 ;
385 ; You may also set the default receive and transmit gains (in dB)
386 ;
387 rxgain=0.0
388 txgain=0.0
389 ;
390 ; Logical groups can be assigned to allow outgoing rollover. Groups range
391 ; from 0 to 63, and multiple groups can be specified.
392 ;
393 group=1
394 ;
395 ; Ring groups (a.k.a. call groups) and pickup groups. If a phone is ringing
396 ; and it is a member of a group which is one of your pickup groups, then
397 ; you can answer it by picking up and dialling *8#. For simple offices, just
398 ; make these both the same. Groups range from 0 to 63.
399 ;
400 callgroup=1
401 pickupgroup=1
403 ;
404 ; Specify whether the channel should be answered immediately or if the simple
405 ; switch should provide dialtone, read digits, etc.
406 ; Note: If immediate=yes the dialplan execution will always start at extension
407 ; 's' priority 1 regardless of the dialed number!
408 ;
409 immediate=no
410 ;
411 ; Specify whether flash-hook transfers to 'busy' channels should complete or
412 ; return to the caller performing the transfer (default is yes).
413 ;
414 ;transfertobusy=no
415 ;
416 ; CallerID can be set to "asreceived" or a specific number if you want to
417 ; override it. Note that "asreceived" only applies to trunk interfaces.
418 ;
419 ;callerid=2564286000
420 ;
421 ; AMA flags affects the recording of Call Detail Records. If specified
422 ; it may be 'default', 'omit', 'billing', or 'documentation'.
423 ;
424 ;amaflags=default
425 ;
426 ; Channels may be associated with an account code to ease
427 ; billing
428 ;
429 ;accountcode=lss0101
430 ;
431 ; ADSI (Analog Display Services Interface) can be enabled on a per-channel
432 ; basis if you have (or may have) ADSI compatible CPE equipment
433 ;
434 ;adsi=yes
435 ;
436 ; SMDI (Simplified Message Desk Interface) can be enabled on a per-channel
437 ; basis if you would like that channel to behave like an SMDI message desk.
438 ; The SMDI port specified should have already been defined in smdi.conf. The
439 ; default port is /dev/ttyS0.
440 ;
441 ;usesmdi=yes
442 ;smdiport=/dev/ttyS0
443 ;
444 ; On trunk interfaces (FXS) and E&M interfaces (E&M, Wink, Feature Group D
445 ; etc, it can be useful to perform busy detection either in an effort to
446 ; detect hangup or for detecting busies. This enables listening for
447 ; the beep-beep busy pattern.
448 ;
449 ;busydetect=yes
450 ;
451 ; If busydetect is enabled, it is also possible to specify how many busy tones
452 ; to wait for before hanging up. The default is 4, but better results can be
453 ; achieved if set to 6 or even 8. Mind that the higher the number, the more
454 ; time that will be needed to hangup a channel, but lowers the probability
455 ; that you will get random hangups.
456 ;
457 ;busycount=4
458 ;
459 ; If busydetect is enabled, it is also possible to specify the cadence of your
460 ; busy signal. In many countries, it is 500msec on, 500msec off. Without
461 ; busypattern specified, we'll accept any regular sound-silence pattern that
462 ; repeats <busycount> times as a busy signal. If you specify busypattern,
463 ; then we'll further check the length of the sound (tone) and silence, which
464 ; will further reduce the chance of a false positive.
465 ;
466 ;busypattern=500,500
467 ;
468 ; NOTE: In the Asterisk Makefile you'll find further options to tweak the busy
469 ; detector. If your country has a busy tone with the same length tone and
470 ; silence (as many countries do), consider defining the
471 ; -DBUSYDETECT_COMPARE_TONE_AND_SILENCE option.
472 ;
473 ; Use a polarity reversal to mark when a outgoing call is answered by the
474 ; remote party.
475 ;
476 ;answeronpolarityswitch=yes
477 ;
478 ; In some countries, a polarity reversal is used to signal the disconnect of a
479 ; phone line. If the hanguponpolarityswitch option is selected, the call will
480 ; be considered "hung up" on a polarity reversal.
481 ;
482 ;hanguponpolarityswitch=yes
483 ;
484 ; On trunk interfaces (FXS) it can be useful to attempt to follow the progress
485 ; of a call through RINGING, BUSY, and ANSWERING. If turned on, call
486 ; progress attempts to determine answer, busy, and ringing on phone lines.
487 ; This feature is HIGHLY EXPERIMENTAL and can easily detect false answers,
488 ; so don't count on it being very accurate.
489 ;
490 ; Few zones are supported at the time of this writing, but may be selected
491 ; with "progzone"
492 ;
493 ; This feature can also easily detect false hangups. The symptoms of this is
494 ; being disconnected in the middle of a call for no reason.
495 ;
496 ;callprogress=yes
497 ;progzone=us
498 ;
499 ; FXO (FXS signalled) devices must have a timeout to determine if there was a
500 ; hangup before the line was answered. This value can be tweaked to shorten
501 ; how long it takes before Zap considers a non-ringing line to have hungup.
502 ;
503 ;ringtimeout=8000
504 ;
505 ; For FXO (FXS signalled) devices, whether to use pulse dial instead of DTMF
506 ;
507 ;pulsedial=yes
508 ;
509 ; For fax detection, uncomment one of the following lines. The default is *OFF*
510 ;
511 ;faxdetect=both
512 ;faxdetect=incoming
513 ;faxdetect=outgoing
514 ;faxdetect=no
515 ;
516 ; This option specifies a preference for which music on hold class this channel
517 ; should listen to when put on hold if the music class has not been set on the
518 ; channel with Set(CHANNEL(musicclass)=whatever) in the dialplan, and the peer
519 ; channel putting this one on hold did not suggest a music class.
520 ;
521 ; If this option is set to "passthrough", then the hold message will always be
522 ; passed through as signalling instead of generating hold music locally. This
523 ; setting is only valid when used on a channel that uses digital signalling.
524 ;
525 ; This option may be specified globally, or on a per-user or per-peer basis.
526 ;
527 ;mohinterpret=default
528 ;
529 ; This option specifies which music on hold class to suggest to the peer channel
530 ; when this channel places the peer on hold. It may be specified globally or on
531 ; a per-user or per-peer basis.
532 ;
533 ;mohsuggest=default
534 ;
535 ; PRI channels can have an idle extension and a minunused number. So long as
536 ; at least "minunused" channels are idle, chan_zap will try to call "idledial"
537 ; on them, and then dump them into the PBX in the "idleext" extension (which
538 ; is of the form exten@context). When channels are needed the "idle" calls
539 ; are disconnected (so long as there are at least "minidle" calls still
540 ; running, of course) to make more channels available. The primary use of
541 ; this is to create a dynamic service, where idle channels are bundled through
542 ; multilink PPP, thus more efficiently utilizing combined voice/data services
543 ; than conventional fixed mappings/muxings.
544 ;
545 ;idledial=6999
546 ;idleext=6999@dialout
547 ;minunused=2
548 ;minidle=1
549 ;
550 ; Configure jitter buffers in zapata (each one is 20ms, default is 4)
551 ;
552 ;jitterbuffers=4
553 ;
554 ;------------------------------ JITTER BUFFER CONFIGURATION --------------------------
555 ; jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of a
556 ; ZAP channel. Defaults to "no". An enabled jitterbuffer will
557 ; be used only if the sending side can create and the receiving
558 ; side can not accept jitter. The ZAP channel can't accept jitter,
559 ; thus an enabled jitterbuffer on the receive ZAP side will always
560 ; be used if the sending side can create jitter.
562 ; jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds.
564 ; jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is
565 ; resynchronized. Useful to improve the quality of the voice, with
566 ; big jumps in/broken timestamps, usually sent from exotic devices
567 ; and programs. Defaults to 1000.
569 ; jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of a ZAP
570 ; channel. Two implementations are currently available - "fixed"
571 ; (with size always equals to jbmax-size) and "adaptive" (with
572 ; variable size, actually the new jb of IAX2). Defaults to fixed.
574 ; jblog = no ; Enables jitterbuffer frame logging. Defaults to "no".
575 ;-----------------------------------------------------------------------------------
576 ;
577 ; You can define your own custom ring cadences here. You can define up to 8
578 ; pairs. If the silence is negative, it indicates where the callerid spill is
579 ; to be placed. Also, if you define any custom cadences, the default cadences
580 ; will be turned off.
581 ;
582 ; Syntax is: cadence=ring,silence[,ring,silence[...]]
583 ;
584 ; These are the default cadences:
585 ;
586 ;cadence=125,125,2000,-4000
587 ;cadence=250,250,500,1000,250,250,500,-4000
588 ;cadence=125,125,125,125,125,-4000
589 ;cadence=1000,500,2500,-5000
590 ;
591 ; Each channel consists of the channel number or range. It inherits the
592 ; parameters that were specified above its declaration.
593 ;
594 ; For GR-303, CRV's are created like channels except they must start with the
595 ; trunk group followed by a colon, e.g.:
596 ;
597 ; crv => 1:1
598 ; crv => 2:1-2,5-8
599 ;
600 ;
601 ;callerid="Green Phone"<(256) 428-6121>
602 ;channel => 1
603 ;callerid="Black Phone"<(256) 428-6122>
604 ;channel => 2
605 ;callerid="CallerID Phone" <(256) 428-6123>
606 ;callerid="CallerID Phone" <(630) 372-1564>
607 ;callerid="CallerID Phone" <(256) 704-4666>
608 ;channel => 3
609 ;callerid="Pac Tel Phone" <(256) 428-6124>
610 ;channel => 4
611 ;callerid="Uniden Dead" <(256) 428-6125>
612 ;channel => 5
613 ;callerid="Cortelco 2500" <(256) 428-6126>
614 ;channel => 6
615 ;callerid="Main TA 750" <(256) 428-6127>
616 ;channel => 44
617 ;
618 ; For example, maybe we have some other channels which start out in a
619 ; different context and use E & M signalling instead.
620 ;
621 ;context=remote
622 ;sigalling=em
623 ;channel => 15
624 ;channel => 16
626 ;signalling=em_w
627 ;
628 ; All those in group 0 I'll use for outgoing calls
629 ;
630 ; Strip most significant digit (9) before sending
631 ;
632 ;stripmsd=1
633 ;callerid=asreceived
634 ;group=0
635 ;signalling=fxs_ls
636 ;channel => 45
638 ;signalling=fxo_ls
639 ;group=1
640 ;callerid="Joe Schmoe" <(256) 428-6131>
641 ;channel => 25
642 ;callerid="Megan May" <(256) 428-6132>
643 ;channel => 26
644 ;callerid="Suzy Queue" <(256) 428-6233>
645 ;channel => 27
646 ;callerid="Larry Moe" <(256) 428-6234>
647 ;channel => 28
648 ;
649 ; Sample PRI (CPE) config: Specify the switchtype, the signalling as either
650 ; pri_cpe or pri_net for CPE or Network termination, and generally you will
651 ; want to create a single "group" for all channels of the PRI.
652 ;
653 ; switchtype = national
654 ; signalling = pri_cpe
655 ; group = 2
656 ; channel => 1-23
658 ;
660 ; Used for distinctive ring support for x100p.
661 ; You can see the dringX patterns is to set any one of the dringXcontext fields
662 ; and they will be printed on the console when an inbound call comes in.
663 ;
664 ;dring1=95,0,0
665 ;dring1context=internal1
666 ;dring2=325,95,0
667 ;dring2context=internal2
668 ; If no pattern is matched here is where we go.
669 ;context=default
670 ;channel => 1