add SDHC support in mmc driver
[u-boot-openmoko/mini2440.git] / include / ns7520_eth.h
blob5019802a33d2ebd935690747b811258cc859266d
1 /***********************************************************************
3 * Copyright 2003 by FS Forth-Systeme GmbH.
4 * All rights reserved.
6 * $Id$
7 * @Author: Markus Pietrek
8 * @Descr: Defines the NS7520 ethernet registers.
9 * Stick with the old ETH prefix names instead going to the
10 * new EFE names in the manual.
11 * NS7520_ETH_* refer to NS7520 Hardware
12 * Reference/January 2003 [1]
13 * PHY_LXT971_* refer to Intel LXT971 Datasheet
14 * #249414 Rev. 02 [2]
15 * Partly derived from netarm_eth_module.h
17 * Modified by Arthur Shipkowski <art@videon-central.com> from the
18 * Linux version to be properly formatted for U-Boot (i.e. no C++ comments)
20 ***********************************************************************/
22 #ifndef FS_NS7520_ETH_H
23 #define FS_NS7520_ETH_H
25 #ifdef CONFIG_DRIVER_NS7520_ETHERNET
27 #include "lxt971a.h"
29 /* The port addresses */
31 #define NS7520_ETH_MODULE_BASE (0xFF800000)
33 #define get_eth_reg_addr(c) \
34 ((volatile unsigned int*) ( NS7520_ETH_MODULE_BASE+(unsigned int) (c)))
35 #define NS7520_ETH_EGCR (0x0000) /* Ethernet Gen Control */
36 #define NS7520_ETH_EGSR (0x0004) /* Ethernet Gen Status */
37 #define NS7520_ETH_FIFO (0x0008) /* FIFO Data */
38 #define NS7520_ETH_FIFOL (0x000C) /* FIFO Data Last */
39 #define NS7520_ETH_ETSR (0x0010) /* Ethernet Transmit Status */
40 #define NS7520_ETH_ERSR (0x0014) /* Ethernet Receive Status */
41 #define NS7520_ETH_MAC1 (0x0400) /* MAC Config 1 */
42 #define NS7520_ETH_MAC2 (0x0404) /* MAC Config 2 */
43 #define NS7520_ETH_IPGT (0x0408) /* Back2Back InterPacket Gap */
44 #define NS7520_ETH_IPGR (0x040C) /* non back2back InterPacket Gap */
45 #define NS7520_ETH_CLRT (0x0410) /* Collision Window/Retry */
46 #define NS7520_ETH_MAXF (0x0414) /* Maximum Frame Register */
47 #define NS7520_ETH_SUPP (0x0418) /* PHY Support */
48 #define NS7520_ETH_TEST (0x041C) /* Test Register */
49 #define NS7520_ETH_MCFG (0x0420) /* MII Management Configuration */
50 #define NS7520_ETH_MCMD (0x0424) /* MII Management Command */
51 #define NS7520_ETH_MADR (0x0428) /* MII Management Address */
52 #define NS7520_ETH_MWTD (0x042C) /* MII Management Write Data */
53 #define NS7520_ETH_MRDD (0x0430) /* MII Management Read Data */
54 #define NS7520_ETH_MIND (0x0434) /* MII Management Indicators */
55 #define NS7520_ETH_SMII (0x0438) /* SMII Status Register */
56 #define NS7520_ETH_SA1 (0x0440) /* Station Address 1 */
57 #define NS7520_ETH_SA2 (0x0444) /* Station Address 2 */
58 #define NS7520_ETH_SA3 (0x0448) /* Station Address 3 */
59 #define NS7520_ETH_SAFR (0x05C0) /* Station Address Filter */
60 #define NS7520_ETH_HT1 (0x05D0) /* Hash Table 1 */
61 #define NS7520_ETH_HT2 (0x05D4) /* Hash Table 2 */
62 #define NS7520_ETH_HT3 (0x05D8) /* Hash Table 3 */
63 #define NS7520_ETH_HT4 (0x05DC) /* Hash Table 4 */
65 /* EGCR Ethernet General Control Register Bit Fields*/
67 #define NS7520_ETH_EGCR_ERX (0x80000000) /* Enable Receive FIFO */
68 #define NS7520_ETH_EGCR_ERXDMA (0x40000000) /* Enable Receive DMA */
69 #define NS7520_ETH_EGCR_ERXLNG (0x20000000) /* Accept Long packets */
70 #define NS7520_ETH_EGCR_ERXSHT (0x10000000) /* Accept Short packets */
71 #define NS7520_ETH_EGCR_ERXREG (0x08000000) /* Enable Receive Data Interrupt */
72 #define NS7520_ETH_EGCR_ERFIFOH (0x04000000) /* Enable Receive Half-Full Int */
73 #define NS7520_ETH_EGCR_ERXBR (0x02000000) /* Enable Receive buffer ready */
74 #define NS7520_ETH_EGCR_ERXBAD (0x01000000) /* Accept bad receive packets */
75 #define NS7520_ETH_EGCR_ETX (0x00800000) /* Enable Transmit FIFO */
76 #define NS7520_ETH_EGCR_ETXDMA (0x00400000) /* Enable Transmit DMA */
77 #define NS7520_ETH_EGCR_ETXWM_R (0x00300000) /* Enable Transmit FIFO mark Reserv */
78 #define NS7520_ETH_EGCR_ETXWM_75 (0x00200000) /* Enable Transmit FIFO mark 75% */
79 #define NS7520_ETH_EGCR_ETXWM_50 (0x00100000) /* Enable Transmit FIFO mark 50% */
80 #define NS7520_ETH_EGCR_ETXWM_25 (0x00000000) /* Enable Transmit FIFO mark 25% */
81 #define NS7520_ETH_EGCR_ETXREG (0x00080000) /* Enable Transmit Data Read Int */
82 #define NS7520_ETH_EGCR_ETFIFOH (0x00040000) /* Enable Transmit Fifo Half Int */
83 #define NS7520_ETH_EGCR_ETXBC (0x00020000) /* Enable Transmit Buffer Compl Int */
84 #define NS7520_ETH_EGCR_EFULLD (0x00010000) /* Enable Full Duplex Operation */
85 #define NS7520_ETH_EGCR_MODE_MA (0x0000C000) /* Mask */
86 #define NS7520_ETH_EGCR_MODE_SEE (0x0000C000) /* 10 Mbps SEEQ ENDEC PHY */
87 #define NS7520_ETH_EGCR_MODE_LEV (0x00008000) /* 10 Mbps Level1 ENDEC PHY */
88 #define NS7520_ETH_EGCR_RES1 (0x00002000) /* Reserved */
89 #define NS7520_ETH_EGCR_RXCINV (0x00001000) /* Invert the receive clock input */
90 #define NS7520_ETH_EGCR_TXCINV (0x00000800) /* Invert the transmit clock input */
91 #define NS7520_ETH_EGCR_PNA (0x00000400) /* pSOS pNA buffer */
92 #define NS7520_ETH_EGCR_MAC_RES (0x00000200) /* MAC Software reset */
93 #define NS7520_ETH_EGCR_ITXA (0x00000100) /* Insert Transmit Source Address */
94 #define NS7520_ETH_EGCR_ENDEC_MA (0x000000FC) /* ENDEC media control bits */
95 #define NS7520_ETH_EGCR_EXINT_MA (0x00000003) /* Mask */
96 #define NS7520_ETH_EGCR_EXINT_RE (0x00000003) /* Reserved */
97 #define NS7520_ETH_EGCR_EXINT_TP (0x00000002) /* TP-PMD Mode */
98 #define NS7520_ETH_EGCR_EXINT_10 (0x00000001) /* 10-MBit Mode */
99 #define NS7520_ETH_EGCR_EXINT_NO (0x00000000) /* MII normal operation */
101 /* EGSR Ethernet General Status Register Bit Fields*/
103 #define NS7520_ETH_EGSR_RES1 (0xC0000000) /* Reserved */
104 #define NS7520_ETH_EGSR_RXFDB_MA (0x30000000) /* Receive FIFO mask */
105 #define NS7520_ETH_EGSR_RXFDB_3 (0x30000000) /* Receive FIFO 3 bytes available */
106 #define NS7520_ETH_EGSR_RXFDB_2 (0x20000000) /* Receive FIFO 2 bytes available */
107 #define NS7520_ETH_EGCR_RXFDB_1 (0x10000000) /* Receive FIFO 1 Bytes available */
108 #define NS7520_ETH_EGCR_RXFDB_4 (0x00000000) /* Receive FIFO 4 Bytes available */
109 #define NS7520_ETH_EGSR_RXREGR (0x08000000) /* Receive Register Ready */
110 #define NS7520_ETH_EGSR_RXFIFOH (0x04000000) /* Receive FIFO Half Full */
111 #define NS7520_ETH_EGSR_RXBR (0x02000000) /* Receive Buffer Ready */
112 #define NS7520_ETH_EGSR_RXSKIP (0x01000000) /* Receive Buffer Skip */
113 #define NS7520_ETH_EGSR_RES2 (0x00F00000) /* Reserved */
114 #define NS7520_ETH_EGSR_TXREGE (0x00080000) /* Transmit Register Empty */
115 #define NS7520_ETH_EGSR_TXFIFOH (0x00040000) /* Transmit FIFO half empty */
116 #define NS7520_ETH_EGSR_TXBC (0x00020000) /* Transmit buffer complete */
117 #define NS7520_ETH_EGSR_TXFIFOE (0x00010000) /* Transmit FIFO empty */
118 #define NS7520_ETH_EGSR_RXPINS (0x0000FC00) /* ENDEC Phy Status */
119 #define NS7520_ETH_EGSR_RES3 (0x000003FF) /* Reserved */
121 /* ETSR Ethernet Transmit Status Register Bit Fields*/
123 #define NS7520_ETH_ETSR_RES1 (0xFFFF0000) /* Reserved */
124 #define NS7520_ETH_ETSR_TXOK (0x00008000) /* Packet transmitted OK */
125 #define NS7520_ETH_ETSR_TXBR (0x00004000) /* Broadcast packet transmitted */
126 #define NS7520_ETH_ETSR_TXMC (0x00002000) /* Multicast packet transmitted */
127 #define NS7520_ETH_ETSR_TXAL (0x00001000) /* Transmit abort - late collision */
128 #define NS7520_ETH_ETSR_TXAED (0x00000800) /* Transmit abort - deferral */
129 #define NS7520_ETH_ETSR_TXAEC (0x00000400) /* Transmit abort - exc collisions */
130 #define NS7520_ETH_ETSR_TXAUR (0x00000200) /* Transmit abort - underrun */
131 #define NS7520_ETH_ETSR_TXAJ (0x00000100) /* Transmit abort - jumbo */
132 #define NS7520_ETH_ETSR_RES2 (0x00000080) /* Reserved */
133 #define NS7520_ETH_ETSR_TXDEF (0x00000040) /* Transmit Packet Deferred */
134 #define NS7520_ETH_ETSR_TXCRC (0x00000020) /* Transmit CRC error */
135 #define NS7520_ETH_ETSR_RES3 (0x00000010) /* Reserved */
136 #define NS7520_ETH_ETSR_TXCOLC (0x0000000F) /* Transmit Collision Count */
138 /* ERSR Ethernet Receive Status Register Bit Fields*/
140 #define NS7520_ETH_ERSR_RXSIZE (0xFFFF0000) /* Receive Buffer Size */
141 #define NS7520_ETH_ERSR_RXCE (0x00008000) /* Receive Carrier Event */
142 #define NS7520_ETH_ERSR_RXDV (0x00004000) /* Receive Data Violation Event */
143 #define NS7520_ETH_ERSR_RXOK (0x00002000) /* Receive Packet OK */
144 #define NS7520_ETH_ERSR_RXBR (0x00001000) /* Receive Broadcast Packet */
145 #define NS7520_ETH_ERSR_RXMC (0x00000800) /* Receive Multicast Packet */
146 #define NS7520_ETH_ERSR_RXCRC (0x00000400) /* Receive Packet has CRC error */
147 #define NS7520_ETH_ERSR_RXDR (0x00000200) /* Receive Packet has dribble error */
148 #define NS7520_ETH_ERSR_RXCV (0x00000100) /* Receive Packet code violation */
149 #define NS7520_ETH_ERSR_RXLNG (0x00000080) /* Receive Packet too long */
150 #define NS7520_ETH_ERSR_RXSHT (0x00000040) /* Receive Packet too short */
151 #define NS7520_ETH_ERSR_ROVER (0x00000020) /* Recive overflow */
152 #define NS7520_ETH_ERSR_RES (0x0000001F) /* Reserved */
154 /* MAC1 MAC Configuration Register 1 Bit Fields*/
156 #define NS7520_ETH_MAC1_RES1 (0xFFFF0000) /* Reserved */
157 #define NS7520_ETH_MAC1_SRST (0x00008000) /* Soft Reset */
158 #define NS7520_ETH_MAC1_SIMMRST (0x00004000) /* Simulation Reset */
159 #define NS7520_ETH_MAC1_RES2 (0x00003000) /* Reserved */
160 #define NS7520_ETH_MAC1_RPEMCSR (0x00000800) /* Reset PEMCS/RX */
161 #define NS7520_ETH_MAC1_RPERFUN (0x00000400) /* Reset PERFUN */
162 #define NS7520_ETH_MAC1_RPEMCST (0x00000200) /* Reset PEMCS/TX */
163 #define NS7520_ETH_MAC1_RPETFUN (0x00000100) /* Reset PETFUN */
164 #define NS7520_ETH_MAC1_RES3 (0x000000E0) /* Reserved */
165 #define NS7520_ETH_MAC1_LOOPBK (0x00000010) /* Internal Loopback */
166 #define NS7520_ETH_MAC1_TXFLOW (0x00000008) /* TX flow control */
167 #define NS7520_ETH_MAC1_RXFLOW (0x00000004) /* RX flow control */
168 #define NS7520_ETH_MAC1_PALLRX (0x00000002) /* Pass ALL receive frames */
169 #define NS7520_ETH_MAC1_RXEN (0x00000001) /* Receive enable */
171 /* MAC Configuration Register 2 Bit Fields*/
173 #define NS7520_ETH_MAC2_RES1 (0xFFFF8000) /* Reserved */
174 #define NS7520_ETH_MAC2_EDEFER (0x00004000) /* Excess Deferral */
175 #define NS7520_ETH_MAC2_BACKP (0x00002000) /* Backpressure/NO back off */
176 #define NS7520_ETH_MAC2_NOBO (0x00001000) /* No back off */
177 #define NS7520_ETH_MAC2_RES2 (0x00000C00) /* Reserved */
178 #define NS7520_ETH_MAC2_LONGP (0x00000200) /* Long Preable enforcement */
179 #define NS7520_ETH_MAC2_PUREP (0x00000100) /* Pure preamble enforcement */
180 #define NS7520_ETH_MAC2_AUTOP (0x00000080) /* Auto detect PAD enable */
181 #define NS7520_ETH_MAC2_VLANP (0x00000040) /* VLAN pad enable */
182 #define NS7520_ETH_MAC2_PADEN (0x00000020) /* PAD/CRC enable */
183 #define NS7520_ETH_MAC2_CRCEN (0x00000010) /* CRC enable */
184 #define NS7520_ETH_MAC2_DELCRC (0x00000008) /* Delayed CRC */
185 #define NS7520_ETH_MAC2_HUGE (0x00000004) /* Huge frame enable */
186 #define NS7520_ETH_MAC2_FLENC (0x00000002) /* Frame length checking */
187 #define NS7520_ETH_MAC2_FULLD (0x00000001) /* Full duplex */
189 /* IPGT Back-to-Back Inter-Packet-Gap Register Bit Fields*/
191 #define NS7520_ETH_IPGT_RES (0xFFFFFF80) /* Reserved */
192 #define NS7520_ETH_IPGT_IPGT (0x0000007F) /* Back-to-Back Interpacket Gap */
194 /* IPGR Non Back-to-Back Inter-Packet-Gap Register Bit Fields*/
196 #define NS7520_ETH_IPGR_RES1 (0xFFFF8000) /* Reserved */
197 #define NS7520_ETH_IPGR_IPGR1 (0x00007F00) /* Non Back-to-back Interpacket Gap */
198 #define NS7520_ETH_IPGR_RES2 (0x00000080) /* Reserved */
199 #define NS7520_ETH_IPGR_IPGR2 (0x0000007F) /* Non back-to-back Interpacket Gap */
201 /* CLRT Collision Windows/Collision Retry Register Bit Fields*/
203 #define NS7520_ETH_CLRT_RES1 (0xFFFFC000) /* Reserved */
204 #define NS7520_ETH_CLRT_CWIN (0x00003F00) /* Collision Windows */
205 #define NS7520_ETH_CLRT_RES2 (0x000000F0) /* Reserved */
206 #define NS7520_ETH_CLRT_RETX (0x0000000F) /* Retransmission maximum */
208 /* MAXF Maximum Frame Register Bit Fields*/
210 #define NS7520_ETH_MAXF_RES1 (0xFFFF0000) /* Reserved */
211 #define NS7520_ETH_MAXF_MAXF (0x0000FFFF) /* Maximum frame length */
213 /* SUPP PHY Support Register Bit Fields*/
215 #define NS7520_ETH_SUPP_RES1 (0xFFFFFF00) /* Reserved */
216 #define NS7520_ETH_SUPP_RPE100X (0x00000080) /* Reset PE100X module */
217 #define NS7520_ETH_SUPP_FORCEQ (0x00000040) /* Force Quit */
218 #define NS7520_ETH_SUPP_NOCIPH (0x00000020) /* No Cipher */
219 #define NS7520_ETH_SUPP_DLINKF (0x00000010) /* Disable link fail */
220 #define NS7520_ETH_SUPP_RPE10T (0x00000008) /* Reset PE10T module */
221 #define NS7520_ETH_SUPP_RES2 (0x00000004) /* Reserved */
222 #define NS7520_ETH_SUPP_JABBER (0x00000002) /* Enable Jabber protection */
223 #define NS7520_ETH_SUPP_BITMODE (0x00000001) /* Bit Mode */
225 /* TEST Register Bit Fields*/
227 #define NS7520_ETH_TEST_RES1 (0xFFFFFFF8) /* Reserved */
228 #define NS7520_ETH_TEST_TBACK (0x00000004) /* Test backpressure */
229 #define NS7520_ETH_TEST_TPAUSE (0x00000002) /* Test Pause */
230 #define NS7520_ETH_TEST_SPQ (0x00000001) /* Shortcut pause quanta */
232 /* MCFG MII Management Configuration Register Bit Fields*/
234 #define NS7520_ETH_MCFG_RES1 (0xFFFF0000) /* Reserved */
235 #define NS7520_ETH_MCFG_RMIIM (0x00008000) /* Reset MII management */
236 #define NS7520_ETH_MCFG_RES2 (0x00007FE0) /* Reserved */
237 #define NS7520_ETH_MCFG_CLKS_MA (0x0000001C) /* Clock Select */
238 #define NS7520_ETH_MCFG_CLKS_4 (0x00000004) /* Sysclk / 4 */
239 #define NS7520_ETH_MCFG_CLKS_6 (0x00000008) /* Sysclk / 6 */
240 #define NS7520_ETH_MCFG_CLKS_8 (0x0000000C) /* Sysclk / 8 */
241 #define NS7520_ETH_MCFG_CLKS_10 (0x00000010) /* Sysclk / 10 */
242 #define NS7520_ETH_MCFG_CLKS_14 (0x00000014) /* Sysclk / 14 */
243 #define NS7520_ETH_MCFG_CLKS_20 (0x00000018) /* Sysclk / 20 */
244 #define NS7520_ETH_MCFG_CLKS_28 (0x0000001C) /* Sysclk / 28 */
245 #define NS7520_ETH_MCFG_SPRE (0x00000002) /* Suppress preamble */
246 #define NS7520_ETH_MCFG_SCANI (0x00000001) /* Scan increment */
248 /* MCMD MII Management Command Register Bit Fields*/
250 #define NS7520_ETH_MCMD_RES1 (0xFFFFFFFC) /* Reserved */
251 #define NS7520_ETH_MCMD_SCAN (0x00000002) /* Automatically Scan for Read Data */
252 #define NS7520_ETH_MCMD_READ (0x00000001) /* Single scan for Read Data */
254 /* MCMD MII Management Address Register Bit Fields*/
256 #define NS7520_ETH_MADR_RES1 (0xFFFFE000) /* Reserved */
257 #define NS7520_ETH_MADR_DADR (0x00001F00) /* MII PHY device address */
258 #define NS7520_ETH_MADR_RES2 (0x000000E0) /* Reserved */
259 #define NS7520_ETH_MADR_RADR (0x0000001F) /* MII PHY register address */
261 /* MWTD MII Management Write Data Register Bit Fields*/
263 #define NS7520_ETH_MWTD_RES1 (0xFFFF0000) /* Reserved */
264 #define NS7520_ETH_MWTD_MWTD (0x0000FFFF) /* MII Write Data */
266 /* MRRD MII Management Read Data Register Bit Fields*/
268 #define NS7520_ETH_MRRD_RES1 (0xFFFF0000) /* Reserved */
269 #define NS7520_ETH_MRRD_MRDD (0x0000FFFF) /* MII Read Data */
271 /* MIND MII Management Indicators Register Bit Fields*/
273 #define NS7520_ETH_MIND_RES1 (0xFFFFFFF8) /* Reserved */
274 #define NS7520_ETH_MIND_NVALID (0x00000004) /* Read Data not valid */
275 #define NS7520_ETH_MIND_SCAN (0x00000002) /* Automatically scan for read data */
276 #define NS7520_ETH_MIND_BUSY (0x00000001) /* MII interface busy */
278 /* SMII Status Register Bit Fields*/
280 #define NS7520_ETH_SMII_RES1 (0xFFFFFFE0) /* Reserved */
281 #define NS7520_ETH_SMII_CLASH (0x00000010) /* MAC-to-MAC with PHY */
282 #define NS7520_ETH_SMII_JABBER (0x00000008) /* Jabber condition present */
283 #define NS7520_ETH_SMII_LINK (0x00000004) /* Link OK */
284 #define NS7520_ETH_SMII_DUPLEX (0x00000002) /* Full-duplex operation */
285 #define NS7520_ETH_SMII_SPEED (0x00000001) /* 100 Mbps */
287 /* SA1 Station Address 1 Register Bit Fields*/
289 #define NS7520_ETH_SA1_RES1 (0xFFFF0000) /* Reserved */
290 #define NS7520_ETH_SA1_OCTET1 (0x0000FF00) /* Station Address octet 1 */
291 #define NS7520_ETH_SA1_OCTET2 (0x000000FF) /* Station Address octet 2 */
293 /* SA2 Station Address 2 Register Bit Fields*/
295 #define NS7520_ETH_SA2_RES1 (0xFFFF0000) /* Reserved */
296 #define NS7520_ETH_SA2_OCTET3 (0x0000FF00) /* Station Address octet 3 */
297 #define NS7520_ETH_SA2_OCTET4 (0x000000FF) /* Station Address octet 4 */
299 /* SA3 Station Address 3 Register Bit Fields*/
301 #define NS7520_ETH_SA3_RES1 (0xFFFF0000) /* Reserved */
302 #define NS7520_ETH_SA3_OCTET5 (0x0000FF00) /* Station Address octet 5 */
303 #define NS7520_ETH_SA3_OCTET6 (0x000000FF) /* Station Address octet 6 */
305 /* SAFR Station Address Filter Register Bit Fields*/
307 #define NS7520_ETH_SAFR_RES1 (0xFFFFFFF0) /* Reserved */
308 #define NS7520_ETH_SAFR_PRO (0x00000008) /* Enable Promiscuous mode */
309 #define NS7520_ETH_SAFR_PRM (0x00000004) /* Accept ALL multicast packets */
310 #define NS7520_ETH_SAFR_PRA (0x00000002) /* Accept multicast packets table */
311 #define NS7520_ETH_SAFR_BROAD (0x00000001) /* Accept ALL Broadcast packets */
313 /* HT1 Hash Table 1 Register Bit Fields*/
315 #define NS7520_ETH_HT1_RES1 (0xFFFF0000) /* Reserved */
316 #define NS7520_ETH_HT1_HT1 (0x0000FFFF) /* CRC value 15-0 */
318 /* HT2 Hash Table 2 Register Bit Fields*/
320 #define NS7520_ETH_HT2_RES1 (0xFFFF0000) /* Reserved */
321 #define NS7520_ETH_HT2_HT2 (0x0000FFFF) /* CRC value 31-16 */
323 /* HT3 Hash Table 3 Register Bit Fields*/
325 #define NS7520_ETH_HT3_RES1 (0xFFFF0000) /* Reserved */
326 #define NS7520_ETH_HT3_HT3 (0x0000FFFF) /* CRC value 47-32 */
328 /* HT4 Hash Table 4 Register Bit Fields*/
330 #define NS7520_ETH_HT4_RES1 (0xFFFF0000) /* Reserved */
331 #define NS7520_ETH_HT4_HT4 (0x0000FFFF) /* CRC value 63-48 */
333 #endif /* CONFIG_DRIVER_NS7520_ETHERNET */
335 #endif /* FS_NS7520_ETH_H */