GUI: Fix Tomato RAF theme for all builds. Compilation typo.

[tomato.git] / release / src-rt-6.x.4708 / linux / linux-2.6.36 / drivers / input / touchscreen / wm9712.c

/*
 * wm9712.c  --  Codec driver for Wolfson WM9712 AC97 Codecs.
 *
 * Copyright 2003, 2004, 2005, 2006, 2007 Wolfson Microelectronics PLC.
 * Author: Liam Girdwood <lrg@slimlogic.co.uk>
 * Parts Copyright : Ian Molton <spyro@f2s.com>
 *                   Andrew Zabolotny <zap@homelink.ru>
 *                   Russell King <rmk@arm.linux.org.uk>
 *
 *  This program is free software; you can redistribute  it and/or modify it
 *  under  the terms of  the GNU General  Public License as published by the
 *  Free Software Foundation;  either version 2 of the  License, or (at your
 *  option) any later version.
 *
 */

#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/kernel.h>
#include <linux/input.h>
#include <linux/delay.h>
#include <linux/bitops.h>
#include <linux/wm97xx.h>

#define TS_NAME                 "wm97xx"
#define WM9712_VERSION          "1.00"
#define DEFAULT_PRESSURE        0xb0c0

/*
 * Module parameters
 */

/*
 * Set internal pull up for pen detect.
 *
 * Pull up is in the range 1.02k (least sensitive) to 64k (most sensitive)
 * i.e. pull up resistance = 64k Ohms / rpu.
 *
 * Adjust this value if you are having problems with pen detect not
 * detecting any down event.
 */
static int rpu = 8;
module_param(rpu, int, 0);
MODULE_PARM_DESC(rpu, "Set internal pull up resitor for pen detect.");

/*
 * Set current used for pressure measurement.
 *
 * Set pil = 2 to use 400uA
 *     pil = 1 to use 200uA and
 *     pil = 0 to disable pressure measurement.
 *
 * This is used to increase the range of values returned by the adc
 * when measureing touchpanel pressure.
 */
static int pil;
module_param(pil, int, 0);
MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");

/*
 * Set threshold for pressure measurement.
 *
 * Pen down pressure below threshold is ignored.
 */
static int pressure = DEFAULT_PRESSURE & 0xfff;
module_param(pressure, int, 0);
MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");

/*
 * Set adc sample delay.
 *
 * For accurate touchpanel measurements, some settling time may be
 * required between the switch matrix applying a voltage across the
 * touchpanel plate and the ADC sampling the signal.
 *
 * This delay can be set by setting delay = n, where n is the array
 * position of the delay in the array delay_table below.
 * Long delays > 1ms are supported for completeness, but are not
 * recommended.
 */
static int delay = 3;
module_param(delay, int, 0);
MODULE_PARM_DESC(delay, "Set adc sample delay.");

/*
 * Set five_wire = 1 to use a 5 wire touchscreen.
 *
 * NOTE: Five wire mode does not allow for readback of pressure.
 */
static int five_wire;
module_param(five_wire, int, 0);
MODULE_PARM_DESC(five_wire, "Set to '1' to use 5-wire touchscreen.");

/*
 * Set adc mask function.
 *
 * Sources of glitch noise, such as signals driving an LCD display, may feed
 * through to the touch screen plates and affect measurement accuracy. In
 * order to minimise this, a signal may be applied to the MASK pin to delay or
 * synchronise the sampling.
 *
 * 0 = No delay or sync
 * 1 = High on pin stops conversions
 * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
 * 3 = Edge triggered, edge on pin starts conversion after delay param
 */
static int mask;
module_param(mask, int, 0);
MODULE_PARM_DESC(mask, "Set adc mask function.");

/*
 * Coordinate Polling Enable.
 *
 * Set to 1 to enable coordinate polling. e.g. x,y[,p] is sampled together
 * for every poll.
 */
static int coord;
module_param(coord, int, 0);
MODULE_PARM_DESC(coord, "Polling coordinate mode");

/*
 * ADC sample delay times in uS
 */
static const int delay_table[] = {
        21,    /* 1 AC97 Link frames */
        42,    /* 2 */
        84,    /* 4 */
        167,   /* 8 */
        333,   /* 16 */
        667,   /* 32 */
        1000,  /* 48 */
        1333,  /* 64 */
        2000,  /* 96 */
        2667,  /* 128 */
        3333,  /* 160 */
        4000,  /* 192 */
        4667,  /* 224 */
        5333,  /* 256 */
        6000,  /* 288 */
        0      /* No delay, switch matrix always on */
};

/*
 * Delay after issuing a POLL command.
 *
 * The delay is 3 AC97 link frames + the touchpanel settling delay
 */
static inline void poll_delay(int d)
{
        udelay(3 * AC97_LINK_FRAME + delay_table[d]);
}

/*
 * set up the physical settings of the WM9712
 */
static void wm9712_phy_init(struct wm97xx *wm)
{
        u16 dig1 = 0;
        u16 dig2 = WM97XX_RPR | WM9712_RPU(1);

        /* WM9712 rpu */
        if (rpu) {
                dig2 &= 0xffc0;
                dig2 |= WM9712_RPU(rpu);
                dev_dbg(wm->dev, "setting pen detect pull-up to %d Ohms",
                        64000 / rpu);
        }

        /* WM9712 five wire */
        if (five_wire) {
                dig2 |= WM9712_45W;
                dev_dbg(wm->dev, "setting 5-wire touchscreen mode.");

                if (pil) {
                        dev_warn(wm->dev, "pressure measurement is not "
                                 "supported in 5-wire mode\n");
                        pil = 0;
                }
        }

        /* touchpanel pressure current*/
        if (pil == 2) {
                dig2 |= WM9712_PIL;
                dev_dbg(wm->dev,
                        "setting pressure measurement current to 400uA.");
        } else if (pil)
                dev_dbg(wm->dev,
                        "setting pressure measurement current to 200uA.");
        if (!pil)
                pressure = 0;

        /* polling mode sample settling delay */
        if (delay < 0 || delay > 15) {
                dev_dbg(wm->dev, "supplied delay out of range.");
                delay = 4;
        }
        dig1 &= 0xff0f;
        dig1 |= WM97XX_DELAY(delay);
        dev_dbg(wm->dev, "setting adc sample delay to %d u Secs.",
                delay_table[delay]);

        /* mask */
        dig2 |= ((mask & 0x3) << 6);
        if (mask) {
                u16 reg;
                /* Set GPIO4 as Mask Pin*/
                reg = wm97xx_reg_read(wm, AC97_MISC_AFE);
                wm97xx_reg_write(wm, AC97_MISC_AFE, reg | WM97XX_GPIO_4);
                reg = wm97xx_reg_read(wm, AC97_GPIO_CFG);
                wm97xx_reg_write(wm, AC97_GPIO_CFG, reg | WM97XX_GPIO_4);
        }

        /* wait - coord mode */
        if (coord)
                dig2 |= WM9712_WAIT;

        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
}

static void wm9712_dig_enable(struct wm97xx *wm, int enable)
{
        u16 dig2 = wm->dig[2];

        if (enable) {
                wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
                                 dig2 | WM97XX_PRP_DET_DIG);
                wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
        } else
                wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
                                 dig2 & ~WM97XX_PRP_DET_DIG);
}

static void wm9712_aux_prepare(struct wm97xx *wm)
{
        memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, 0);
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, WM97XX_PRP_DET_DIG);
}

static void wm9712_dig_restore(struct wm97xx *wm)
{
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, wm->dig_save[1]);
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, wm->dig_save[2]);
}

static inline int is_pden(struct wm97xx *wm)
{
        return wm->dig[2] & WM9712_PDEN;
}

/*
 * Read a sample from the WM9712 adc in polling mode.
 */
static int wm9712_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
{
        int timeout = 5 * delay;

        if (!wm->pen_probably_down) {
                u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
                if (!(data & WM97XX_PEN_DOWN))
                        return RC_PENUP;
                wm->pen_probably_down = 1;
        }

        /* set up digitiser */
        if (adcsel & 0x8000)
                adcsel = ((adcsel & 0x7fff) + 3) << 12;

        if (wm->mach_ops && wm->mach_ops->pre_sample)
                wm->mach_ops->pre_sample(adcsel);
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
                         adcsel | WM97XX_POLL | WM97XX_DELAY(delay));

        /* wait 3 AC97 time slots + delay for conversion */
        poll_delay(delay);

        /* wait for POLL to go low */
        while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
               && timeout) {
                udelay(AC97_LINK_FRAME);
                timeout--;
        }

        if (timeout <= 0) {
                /* If PDEN is set, we can get a timeout when pen goes up */
                if (is_pden(wm))
                        wm->pen_probably_down = 0;
                else
                        dev_dbg(wm->dev, "adc sample timeout");
                return RC_PENUP;
        }

        *sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
        if (wm->mach_ops && wm->mach_ops->post_sample)
                wm->mach_ops->post_sample(adcsel);

        /* check we have correct sample */
        if ((*sample & WM97XX_ADCSEL_MASK) != adcsel) {
                dev_dbg(wm->dev, "adc wrong sample, read %x got %x", adcsel,
                *sample & WM97XX_ADCSEL_MASK);
                return RC_PENUP;
        }

        if (!(*sample & WM97XX_PEN_DOWN)) {
                wm->pen_probably_down = 0;
                return RC_PENUP;
        }

        return RC_VALID;
}

/*
 * Read a coord from the WM9712 adc in polling mode.
 */
static int wm9712_poll_coord(struct wm97xx *wm, struct wm97xx_data *data)
{
        int timeout = 5 * delay;

        if (!wm->pen_probably_down) {
                u16 data_rd = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
                if (!(data_rd & WM97XX_PEN_DOWN))
                        return RC_PENUP;
                wm->pen_probably_down = 1;
        }

        /* set up digitiser */
        if (wm->mach_ops && wm->mach_ops->pre_sample)
                wm->mach_ops->pre_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);

        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
                WM97XX_COO | WM97XX_POLL | WM97XX_DELAY(delay));

        /* wait 3 AC97 time slots + delay for conversion and read x */
        poll_delay(delay);
        data->x = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
        /* wait for POLL to go low */
        while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
               && timeout) {
                udelay(AC97_LINK_FRAME);
                timeout--;
        }

        if (timeout <= 0) {
                /* If PDEN is set, we can get a timeout when pen goes up */
                if (is_pden(wm))
                        wm->pen_probably_down = 0;
                else
                        dev_dbg(wm->dev, "adc sample timeout");
                return RC_PENUP;
        }

        /* read back y data */
        data->y = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
        if (pil)
                data->p = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
        else
                data->p = DEFAULT_PRESSURE;

        if (wm->mach_ops && wm->mach_ops->post_sample)
                wm->mach_ops->post_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);

        /* check we have correct sample */
        if (!(data->x & WM97XX_ADCSEL_X) || !(data->y & WM97XX_ADCSEL_Y))
                goto err;
        if (pil && !(data->p & WM97XX_ADCSEL_PRES))
                goto err;

        if (!(data->x & WM97XX_PEN_DOWN) || !(data->y & WM97XX_PEN_DOWN)) {
                wm->pen_probably_down = 0;
                return RC_PENUP;
        }
        return RC_VALID;
err:
        return 0;
}

/*
 * Sample the WM9712 touchscreen in polling mode
 */
static int wm9712_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
{
        int rc;

        if (coord) {
                rc = wm9712_poll_coord(wm, data);
                if (rc != RC_VALID)
                        return rc;
        } else {
                rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_X, &data->x);
                if (rc != RC_VALID)
                        return rc;

                rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_Y, &data->y);
                if (rc != RC_VALID)
                        return rc;

                if (pil && !five_wire) {
                        rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_PRES,
                                                &data->p);
                        if (rc != RC_VALID)
                                return rc;
                } else
                        data->p = DEFAULT_PRESSURE;
        }
        return RC_VALID;
}

/*
 * Enable WM9712 continuous mode, i.e. touch data is streamed across
 * an AC97 slot
 */
static int wm9712_acc_enable(struct wm97xx *wm, int enable)
{
        u16 dig1, dig2;
        int ret = 0;

        dig1 = wm->dig[1];
        dig2 = wm->dig[2];

        if (enable) {
                /* continous mode */
                if (wm->mach_ops->acc_startup) {
                        ret = wm->mach_ops->acc_startup(wm);
                        if (ret < 0)
                                return ret;
                }
                dig1 &= ~(WM97XX_CM_RATE_MASK | WM97XX_ADCSEL_MASK |
                        WM97XX_DELAY_MASK | WM97XX_SLT_MASK);
                dig1 |= WM97XX_CTC | WM97XX_COO | WM97XX_SLEN |
                        WM97XX_DELAY(delay) |
                        WM97XX_SLT(wm->acc_slot) |
                        WM97XX_RATE(wm->acc_rate);
                if (pil)
                        dig1 |= WM97XX_ADCSEL_PRES;
                dig2 |= WM9712_PDEN;
        } else {
                dig1 &= ~(WM97XX_CTC | WM97XX_COO | WM97XX_SLEN);
                dig2 &= ~WM9712_PDEN;
                if (wm->mach_ops->acc_shutdown)
                        wm->mach_ops->acc_shutdown(wm);
        }

        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
        wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);

        return 0;
}

struct wm97xx_codec_drv wm9712_codec = {
        .id = WM9712_ID2,
        .name = "wm9712",
        .poll_sample = wm9712_poll_sample,
        .poll_touch = wm9712_poll_touch,
        .acc_enable = wm9712_acc_enable,
        .phy_init = wm9712_phy_init,
        .dig_enable = wm9712_dig_enable,
        .dig_restore = wm9712_dig_restore,
        .aux_prepare = wm9712_aux_prepare,
};
EXPORT_SYMBOL_GPL(wm9712_codec);

/* Module information */
MODULE_AUTHOR("Liam Girdwood <lrg@slimlogic.co.uk>");
MODULE_DESCRIPTION("WM9712 Touch Screen Driver");
MODULE_LICENSE("GPL");