release/src-rt-6.x.4708/linux/linux-2.6.36/drivers/ide/dtc2278.c

   1 /*
   2  *  Copyright (C) 1996  Linus Torvalds & author (see below)
   3  */
   4
   5 #include <linux/module.h>
   6 #include <linux/types.h>
   7 #include <linux/kernel.h>
   8 #include <linux/delay.h>
   9 #include <linux/timer.h>
  10 #include <linux/mm.h>
  11 #include <linux/ioport.h>
  12 #include <linux/blkdev.h>
  13 #include <linux/ide.h>
  14 #include <linux/init.h>
  15
  16 #include <asm/io.h>
  17
  18 #define DRV_NAME "dtc2278"
  19
  20 /*
  21  * Changing this #undef to #define may solve start up problems in some systems.
  22  */
  23 #undef ALWAYS_SET_DTC2278_PIO_MODE
  24
  25 /*
  26  * From: andy@cercle.cts.com (Dyan Wile)
  27  *
  28  * Below is a patch for DTC-2278 - alike software-programmable controllers
  29  * The code enables the secondary IDE controller and the PIO4 (3?) timings on
  30  * the primary (EIDE). You may probably have to enable the 32-bit support to
  31  * get the full speed. You better get the disk interrupts disabled ( hdparm -u0
  32  * /dev/hd.. ) for the drives connected to the EIDE interface. (I get my
  33  * filesystem  corrupted with -u1, but under heavy disk load only :-)
  34  *
  35  * This card is now forced to use the "serialize" feature,
  36  * and irq-unmasking is disallowed.  If io_32bit is enabled,
  37  * it must be done for BOTH drives on each interface.
  38  *
  39  * This code was written for the DTC2278E, but might work with any of these:
  40  *
  41  * DTC2278S has only a single IDE interface.
  42  * DTC2278D has two IDE interfaces and is otherwise identical to the S version.
  43  * DTC2278E also has serial ports and a printer port
  44  * DTC2278EB: has onboard BIOS, and "works like a charm" -- Kent Bradford <kent@theory.caltech.edu>
  45  *
  46  * There may be a fourth controller type. The S and D versions use the
  47  * Winbond chip, and I think the E version does also.
  48  *
  49  */
  50
  51 static void sub22 (char b, char c)
  52 {
  53         int i;
  54
  55         for(i = 0; i < 3; ++i) {
  56                 inb(0x3f6);
  57                 outb_p(b,0xb0);
  58                 inb(0x3f6);
  59                 outb_p(c,0xb4);
  60                 inb(0x3f6);
  61                 if(inb(0xb4) == c) {
  62                         outb_p(7,0xb0);
  63                         inb(0x3f6);
  64                         return; /* success */
  65                 }
  66         }
  67 }
  68
  69 static DEFINE_SPINLOCK(dtc2278_lock);
  70
  71 static void dtc2278_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
  72 {
  73         unsigned long flags;
  74
  75         if (drive->pio_mode >= XFER_PIO_3) {
  76                 spin_lock_irqsave(&dtc2278_lock, flags);
  77                 /*
  78                  * This enables PIO mode4 (3?) on the first interface
  79                  */
  80                 sub22(1,0xc3);
  81                 sub22(0,0xa0);
  82                 spin_unlock_irqrestore(&dtc2278_lock, flags);
  83         } else {
  84                 /* we don't know how to set it back again.. */
  85                 /* Actually we do - there is a data sheet available for the
  86                    Winbond but does anyone actually care */
  87         }
  88 }
  89
  90 static const struct ide_port_ops dtc2278_port_ops = {
  91         .set_pio_mode           = dtc2278_set_pio_mode,
  92 };
  93
  94 static const struct ide_port_info dtc2278_port_info __initdata = {
  95         .name                   = DRV_NAME,
  96         .chipset                = ide_dtc2278,
  97         .port_ops               = &dtc2278_port_ops,
  98         .host_flags             = IDE_HFLAG_SERIALIZE |
  99                                   IDE_HFLAG_NO_UNMASK_IRQS |
 100                                   IDE_HFLAG_IO_32BIT |
 101                                   /* disallow ->io_32bit changes */
 102                                   IDE_HFLAG_NO_IO_32BIT |
 103                                   IDE_HFLAG_NO_DMA |
 104                                   IDE_HFLAG_DTC2278,
 105         .pio_mask               = ATA_PIO4,
 106 };
 107
 108 static int __init dtc2278_probe(void)
 109 {
 110         unsigned long flags;
 111
 112         local_irq_save(flags);
 113         /*
 114          * This enables the second interface
 115          */
 116         outb_p(4,0xb0);
 117         inb(0x3f6);
 118         outb_p(0x20,0xb4);
 119         inb(0x3f6);
 120 #ifdef ALWAYS_SET_DTC2278_PIO_MODE
 121         /*
 122          * This enables PIO mode4 (3?) on the first interface
 123          * and may solve start-up problems for some people.
 124          */
 125         sub22(1,0xc3);
 126         sub22(0,0xa0);
 127 #endif
 128         local_irq_restore(flags);
 129
 130         return ide_legacy_device_add(&dtc2278_port_info, 0);
 131 }
 132
 133 static int probe_dtc2278;
 134
 135 module_param_named(probe, probe_dtc2278, bool, 0);
 136 MODULE_PARM_DESC(probe, "probe for DTC2278xx chipsets");
 137
 138 static int __init dtc2278_init(void)
 139 {
 140         if (probe_dtc2278 == 0)
 141                 return -ENODEV;
 142
 143         if (dtc2278_probe()) {
 144                 printk(KERN_ERR "dtc2278: ide interfaces already in use!\n");
 145                 return -EBUSY;
 146         }
 147         return 0;
 148 }
 149
 150 module_init(dtc2278_init);
 151
 152 MODULE_AUTHOR("See Local File");
 153 MODULE_DESCRIPTION("support of DTC-2278 VLB IDE chipsets");
 154 MODULE_LICENSE("GPL");