Add init_board procedure executed after init_targets

[openocd.git] / src / target / startup.tcl

# Defines basic Tcl procs for OpenOCD target module

proc new_target_name { } {
        return [target number [expr [target count] - 1 ]]
}

global in_process_reset
set in_process_reset 0

# Catch reset recursion
proc ocd_process_reset { MODE } {
        global in_process_reset
        if {$in_process_reset} {
                set in_process_reset 0
                return -code error "'reset' can not be invoked recursively"
        }

        set in_process_reset 1
        set success [expr [catch {ocd_process_reset_inner $MODE} result]==0]
        set in_process_reset 0

        if {$success} {
                return $result
        } else {
                return -code error $result
        }
}

proc ocd_process_reset_inner { MODE } {
        set targets [target names]

        # If this target must be halted...
        set halt -1
        if { 0 == [string compare $MODE halt] } {
                set halt 1
        }
        if { 0 == [string compare $MODE init] } {
                set halt 1;
        }
        if { 0 == [string compare $MODE run ] } {
                set halt 0;
        }
        if { $halt < 0 } {
                return -code error "Invalid mode: $MODE, must be one of: halt, init, or run";
        }

        # Target event handlers *might* change which TAPs are enabled
        # or disabled, so we fire all of them.  But don't issue any
        # target "arp_*" commands, which may issue JTAG transactions,
        # unless we know the underlying TAP is active.
        #
        # NOTE:  ARP == "Advanced Reset Process" ... "advanced" is
        # relative to a previous restrictive scheme

        foreach t $targets {
                # New event script.
                $t invoke-event reset-start
        }

        # Use TRST or TMS/TCK operations to reset all the tap controllers.
        # TAP reset events get reported; they might enable some taps.
        init_reset $MODE

        # Examine all targets on enabled taps.
        foreach t $targets {
                if {[jtag tapisenabled [$t cget -chain-position]]} {
                        $t arp_examine
                }
        }

        # Assert SRST, and report the pre/post events.
        # Note:  no target sees SRST before "pre" or after "post".
        foreach t $targets {
                $t invoke-event reset-assert-pre
        }
        foreach t $targets {
                # C code needs to know if we expect to 'halt'
                if {[jtag tapisenabled [$t cget -chain-position]]} {
                        $t arp_reset assert $halt
                }
        }
        foreach t $targets {
                $t invoke-event reset-assert-post
        }

        # Now de-assert SRST, and report the pre/post events.
        # Note:  no target sees !SRST before "pre" or after "post".
        foreach t $targets {
                $t invoke-event reset-deassert-pre
        }
        foreach t $targets {
                # Again, de-assert code needs to know if we 'halt'
                if {[jtag tapisenabled [$t cget -chain-position]]} {
                        $t arp_reset deassert $halt
                }
        }
        foreach t $targets {
                $t invoke-event reset-deassert-post
        }

        # Pass 1 - Now wait for any halt (requested as part of reset
        # assert/deassert) to happen.  Ideally it takes effect without
        # first executing any instructions.
        if { $halt } {
                foreach t $targets {
                        if {[jtag tapisenabled [$t cget -chain-position]] == 0} {
                                continue
                        }

                        # Wait upto 1 second for target to halt.  Why 1sec? Cause
                        # the JTAG tap reset signal might be hooked to a slow
                        # resistor/capacitor circuit - and it might take a while
                        # to charge

                        # Catch, but ignore any errors.
                        catch { $t arp_waitstate halted 1000 }

                        # Did we succeed?
                        set s [$t curstate]

                        if { 0 != [string compare $s "halted" ] } {
                                return -code error [format "TARGET: %s - Not halted" $t]
                        }
                }
        }

        #Pass 2 - if needed "init"
        if { 0 == [string compare init $MODE] } {
                foreach t $targets {
                        if {[jtag tapisenabled [$t cget -chain-position]] == 0} {
                                continue
                        }

                        set err [catch "$t arp_waitstate halted 5000"]
                        # Did it halt?
                        if { $err == 0 } {
                                $t invoke-event reset-init
                        }
                }
        }

        foreach t $targets {
                $t invoke-event reset-end
        }
}

#########

# Temporary migration aid.  May be removed starting in January 2011.
proc armv4_5 params {
        echo "DEPRECATED! use 'arm $params' not 'armv4_5 $params'"
        arm $params
}

# Target/chain configuration scripts can either execute commands directly 
# or define a procedure which is executed once all configuration 
# scripts have completed.
#
# By default(classic) the config scripts will set up the target configuration
proc init_targets {} {
}

# Additionally board config scripts can define a procedure init_board that will be executed after init and init_targets
proc init_board {} {
}