nuttx/configs/hymini-stm32v/nxlines/defconfig

   1 ############################################################################
   2 # configs/hymini-stm32v/nxlines/defconfig
   3 #
   4 #   Copyright (C) 2011-2012 Gregory Nutt. All rights reserved.
   5 #   Author: Gregory Nutt <gnutt@nuttx.org>
   6 #
   7 # Redistribution and use in source and binary forms, with or without
   8 # modification, are permitted provided that the following conditions
   9 # are met:
  10 #
  11 # 1. Redistributions of source code must retain the above copyright
  12 #    notice, this list of conditions and the following disclaimer.
  13 # 2. Redistributions in binary form must reproduce the above copyright
  14 #    notice, this list of conditions and the following disclaimer in
  15 #    the documentation and/or other materials provided with the
  16 #    distribution.
  17 # 3. Neither the name NuttX nor the names of its contributors may be
  18 #    used to endorse or promote products derived from this software
  19 #    without specific prior written permission.
  20 #
  21 # THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
  22 # "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
  23 # LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
  24 # FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
  25 # COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
  26 # INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
  27 # BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
  28 # OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
  29 # AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
  30 # LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
  31 # ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
  32 # POSSIBILITY OF SUCH DAMAGE.
  33 #
  34 ############################################################################
  35 #
  36 # Architecture Selection
  37 #
  38 CONFIG_ARCH="arm"
  39 CONFIG_ARCH_ARM=y
  40 CONFIG_ARCH_CORTEXM3=y
  41 CONFIG_ARCH_CHIP="stm32"
  42 CONFIG_ARCH_CHIP_STM32F103VCT6=y
  43 CONFIG_ARCH_BOARD="hymini-stm32v"
  44 CONFIG_ARCH_BOARD_HYMINI_STM32V=y
  45
  46 CONFIG_BOARD_LOOPSPERMSEC=5483
  47 CONFIG_DRAM_SIZE=49152
  48 CONFIG_DRAM_START=0x20000000
  49 CONFIG_ARCH_IRQPRIO=y
  50 CONFIG_ARCH_INTERRUPTSTACK=n
  51 CONFIG_ARCH_STACKDUMP=y
  52 CONFIG_ARCH_BOOTLOADER=n
  53 CONFIG_ARCH_LEDS=y
  54 CONFIG_ARCH_BUTTONS=n
  55 CONFIG_ARCH_CALIBRATION=n
  56 CONFIG_ARCH_DMA=y
  57
  58 #
  59 # Identify toolchain and linker options
  60 #
  61 CONFIG_STM32_CODESOURCERYW=n
  62 CONFIG_STM32_CODESOURCERYL=y
  63 CONFIG_STM32_DEVKITARM=n
  64 CONFIG_STM32_RAISONANCE=n
  65 CONFIG_STM32_BUILDROOT=n
  66 CONFIG_STM32_DFU=n
  67
  68 #
  69 # Individual subsystems can be enabled:
  70 # AHB:
  71 CONFIG_STM32_DMA1=n
  72 CONFIG_STM32_DMA2=y
  73 CONFIG_STM32_CRC=n
  74 CONFIG_STM32_FSMC=y
  75 CONFIG_STM32_SDIO=y
  76 # APB1:
  77 CONFIG_STM32_TIM2=n
  78 CONFIG_STM32_TIM3=n
  79 CONFIG_STM32_TIM4=n
  80 CONFIG_STM32_TIM5=n
  81 CONFIG_STM32_TIM6=n
  82 CONFIG_STM32_TIM7=n
  83 CONFIG_STM32_WWDG=n
  84 CONFIG_STM32_IWDG=n
  85 CONFIG_STM32_SPI2=n
  86 CONFIG_STM32_SPI4=n
  87 CONFIG_STM32_USART2=y
  88 CONFIG_STM32_USART3=n
  89 CONFIG_STM32_UART4=n
  90 CONFIG_STM32_UART5=n
  91 CONFIG_STM32_I2C1=y
  92 CONFIG_STM32_I2C2=n
  93 CONFIG_STM32_USB=y
  94 CONFIG_STM32_CAN1=n
  95 CONFIG_STM32_BKP=n
  96 CONFIG_STM32_PWR=n
  97 CONFIG_STM32_DAC=n
  98
  99 CONFIG_STM32_TIM3_PARTIAL_REMAP=y
 100
 101 # APB2:
 102 CONFIG_STM32_ADC1=n
 103 CONFIG_STM32_ADC2=n
 104 CONFIG_STM32_TIM1=n
 105 CONFIG_STM32_SPI1=n
 106 CONFIG_STM32_TIM8=n
 107 CONFIG_STM32_USART1=y
 108 CONFIG_STM32_ADC3=n
 109
 110 #
 111 # Timer and I2C devices may need to the following to force power to be applied:
 112 #
 113 #CONFIG_STM32_FORCEPOWER=y
 114
 115 #
 116 # STM32F103Z specific serial device driver settings
 117 #
 118 CONFIG_USART1_SERIAL_CONSOLE=y
 119 CONFIG_USART2_SERIAL_CONSOLE=n
 120 CONFIG_USART3_SERIAL_CONSOLE=n
 121 CONFIG_UART4_SERIAL_CONSOLE=n
 122 CONFIG_UART5_SERIAL_CONSOLE=n
 123
 124 CONFIG_USART1_TXBUFSIZE=256
 125 CONFIG_USART2_TXBUFSIZE=256
 126 CONFIG_USART3_TXBUFSIZE=256
 127 CONFIG_UART4_TXBUFSIZE=256
 128 CONFIG_UART5_TXBUFSIZE=256
 129
 130 CONFIG_USART1_RXBUFSIZE=256
 131 CONFIG_USART2_RXBUFSIZE=256
 132 CONFIG_USART3_RXBUFSIZE=256
 133 CONFIG_UART4_RXBUFSIZE=256
 134 CONFIG_UART5_RXBUFSIZE=256
 135
 136 CONFIG_USART1_BAUD=115200
 137 CONFIG_USART2_BAUD=115200
 138 CONFIG_USART3_BAUD=115200
 139 CONFIG_UART4_BAUD=115200
 140 CONFIG_UART5_BAUD=115200
 141
 142 CONFIG_USART1_BITS=8
 143 CONFIG_USART2_BITS=8
 144 CONFIG_USART3_BITS=8
 145 CONFIG_UART4_BITS=8
 146 CONFIG_UART5_BITS=8
 147
 148 CONFIG_USART1_PARITY=0
 149 CONFIG_USART2_PARITY=0
 150 CONFIG_USART3_PARITY=0
 151 CONFIG_UART4_PARITY=0
 152 CONFIG_UART5_PARITY=0
 153
 154 CONFIG_USART1_2STOP=0
 155 CONFIG_USART2_2STOP=0
 156 CONFIG_USART3_2STOP=0
 157 CONFIG_UART4_2STOP=0
 158 CONFIG_UART5_2STOP=0
 159
 160 #
 161 # STM32F103V specific SSI device driver settings
 162 #
 163 CONFIG_SSI0_DISABLE=n
 164 CONFIG_SSI1_DISABLE=y
 165 CONFIG_SSI_POLLWAIT=y
 166 #CONFIG_SSI_TXLIMIT=4
 167
 168 #
 169 # General build options
 170 #
 171 CONFIG_RRLOAD_BINARY=n
 172 CONFIG_INTELHEX_BINARY=y
 173 CONFIG_MOTOROLA_SREC=n
 174 CONFIG_RAW_BINARY=n
 175 CONFIG_HAVE_LIBM=n
 176
 177 #
 178 # General OS setup
 179 #
 180 CONFIG_USER_ENTRYPOINT="nxlines_main"
 181 CONFIG_DEBUG=n
 182 CONFIG_DEBUG_VERBOSE=n
 183 CONFIG_DEBUG_GRAPHICS=n
 184 CONFIG_DEBUG_LCD=n
 185 CONFIG_DEBUG_SYMBOLS=n
 186 CONFIG_MM_REGIONS=1
 187 CONFIG_ARCH_LOWPUTC=y
 188 CONFIG_RR_INTERVAL=200
 189 CONFIG_SCHED_INSTRUMENTATION=n
 190 CONFIG_TASK_NAME_SIZE=0
 191 CONFIG_START_YEAR=2011
 192 CONFIG_START_MONTH=7
 193 CONFIG_START_DAY=8
 194 CONFIG_GREGORIAN_TIME=n
 195 CONFIG_JULIAN_TIME=n
 196 CONFIG_DEV_CONSOLE=y
 197 CONFIG_DEV_LOWCONSOLE=y
 198 CONFIG_MUTEX_TYPES=n
 199 CONFIG_PRIORITY_INHERITANCE=n
 200 CONFIG_SEM_PREALLOCHOLDERS=0
 201 CONFIG_SEM_NNESTPRIO=0
 202 CONFIG_FDCLONE_DISABLE=n
 203 CONFIG_FDCLONE_STDIO=n
 204 CONFIG_SDCLONE_DISABLE=y
 205 CONFIG_SCHED_WORKQUEUE=y
 206 CONFIG_SCHED_WORKPRIORITY=192
 207 CONFIG_SCHED_WORKPERIOD=50000
 208 CONFIG_SCHED_WORKSTACKSIZE=1024
 209 CONFIG_SIG_SIGWORK=4
 210
 211 #
 212 # Settings for NXFLAT
 213 #
 214 CONFIG_NXFLAT=n
 215 CONFIG_NXFLAT_DUMPBUFFER=n
 216 CONFIG_SYMTAB_ORDEREDBYNAME=y
 217
 218 #
 219 # The following can be used to disable categories of
 220 # APIs supported by the OS.  If the compiler supports
 221 # weak functions, then it should not be necessary to
 222 # disable functions unless you want to restrict usage
 223 # of those APIs.
 224 #
 225 # There are certain dependency relationships in these
 226 # features.
 227 #
 228 # o mq_notify logic depends on signals to awaken tasks
 229 #   waiting for queues to become full or empty.
 230 # o pthread_condtimedwait() depends on signals to wake
 231 #   up waiting tasks.
 232 #
 233 CONFIG_DISABLE_CLOCK=n
 234 CONFIG_DISABLE_POSIX_TIMERS=y
 235 CONFIG_DISABLE_PTHREAD=n
 236 CONFIG_DISABLE_SIGNALS=n
 237 CONFIG_DISABLE_MQUEUE=n
 238 CONFIG_DISABLE_MOUNTPOINT=y
 239 CONFIG_DISABLE_ENVIRON=y
 240 CONFIG_DISABLE_POLL=y
 241
 242 #
 243 # Misc libc settings
 244 #
 245 CONFIG_NOPRINTF_FIELDWIDTH=n
 246
 247 #
 248 # Allow for architecture optimized implementations
 249 #
 250 # The architecture can provide optimized versions of the
 251 # following to improve system performance
 252 #
 253 CONFIG_ARCH_MEMCPY=n
 254 CONFIG_ARCH_MEMCMP=n
 255 CONFIG_ARCH_MEMMOVE=n
 256 CONFIG_ARCH_MEMSET=n
 257 CONFIG_ARCH_STRCMP=n
 258 CONFIG_ARCH_STRCPY=n
 259 CONFIG_ARCH_STRNCPY=n
 260 CONFIG_ARCH_STRLEN=n
 261 CONFIG_ARCH_STRNLEN=n
 262 CONFIG_ARCH_BZERO=n
 263
 264 #
 265 # Sizes of configurable things (0 disables)
 266 #
 267 CONFIG_MAX_TASKS=16
 268 CONFIG_MAX_TASK_ARGS=4
 269 CONFIG_NPTHREAD_KEYS=4
 270 CONFIG_NFILE_DESCRIPTORS=12
 271 CONFIG_NFILE_STREAMS=12
 272 CONFIG_NAME_MAX=32
 273 CONFIG_STDIO_BUFFER_SIZE=256
 274 CONFIG_NUNGET_CHARS=2
 275 CONFIG_PREALLOC_MQ_MSGS=4
 276 CONFIG_MQ_MAXMSGSIZE=32
 277 CONFIG_MAX_WDOGPARMS=2
 278 CONFIG_PREALLOC_WDOGS=4
 279 CONFIG_PREALLOC_TIMERS=4
 280
 281 #
 282 # Framebuffer driver options
 283 #
 284 CONFIG_FB_CMAP=n
 285 CONFIG_FB_HWCURSOR=n
 286 CONFIG_FB_HWCURSORIMAGE=n
 287 #CONFIG_FB_HWCURSORSIZE
 288 #CONFIG_FB_TRANSPARENCY
 289
 290 #
 291 # Filesystem configuration
 292 #
 293 CONFIG_FS_FAT=n
 294 CONFIG_FAT_LCNAMES=n
 295 CONFIG_FAT_LFN=n
 296 CONFIG_FAT_MAXFNAME=32
 297 CONFIG_FS_NXFFS=n
 298 CONFIG_FS_ROMFS=n
 299
 300 #
 301 # SPI-based MMC/SD driver
 302 #
 303 CONFIG_MMCSD_NSLOTS=1
 304 CONFIG_MMCSD_READONLY=n
 305 CONFIG_MMCSD_SPICLOCK=12500000
 306
 307 #
 308 # Block driver buffering
 309 #
 310 CONFIG_FS_READAHEAD=n
 311 CONFIG_FS_WRITEBUFFER=n
 312
 313 #
 314 # SDIO-based MMC/SD driver
 315 #
 316 CONFIG_SDIO_DMA=y
 317 CONFIG_MMCSD_MMCSUPPORT=n
 318 CONFIG_MMCSD_HAVECARDDETECT=n
 319
 320 #
 321 # TCP/IP and UDP support via uIP
 322 #
 323 CONFIG_NET=n
 324 CONFIG_NET_IPv6=n
 325 CONFIG_NSOCKET_DESCRIPTORS=0
 326 CONFIG_NET_SOCKOPTS=y
 327 CONFIG_NET_BUFSIZE=420
 328 CONFIG_NET_TCP=n
 329 CONFIG_NET_TCP_CONNS=40
 330 CONFIG_NET_MAX_LISTENPORTS=40
 331 CONFIG_NET_UDP=n
 332 CONFIG_NET_UDP_CHECKSUMS=y
 333 #CONFIG_NET_UDP_CONNS=10
 334 CONFIG_NET_ICMP=n
 335 CONFIG_NET_ICMP_PING=n
 336 #CONFIG_NET_PINGADDRCONF=0
 337 CONFIG_NET_STATISTICS=y
 338 #CONFIG_NET_RECEIVE_WINDOW=
 339 #CONFIG_NET_ARPTAB_SIZE=8
 340 CONFIG_NET_BROADCAST=n
 341 #CONFIG_NET_FWCACHE_SIZE=2
 342
 343 #
 344 # UIP Network Utilities
 345 #
 346 CONFIG_NET_DHCP_LIGHT=n
 347 CONFIG_NET_RESOLV_ENTRIES=4
 348
 349 #
 350 # USB Device Configuration
 351 #
 352 CONFIG_USBDEV=n
 353 CONFIG_USBDEV_ISOCHRONOUS=n
 354 CONFIG_USBDEV_DUALSPEED=n
 355 CONFIG_USBDEV_SELFPOWERED=y
 356 CONFIG_USBDEV_REMOTEWAKEUP=n
 357 CONFIG_USBDEV_MAXPOWER=100
 358 CONFIG_USBDEV_TRACE=n
 359 CONFIG_USBDEV_TRACE_NRECORDS=128
 360
 361 #
 362 # USB Serial Device Configuration
 363 #
 364 CONFIG_PL2303=n
 365 CONFIG_PL2303_EPINTIN=1
 366 CONFIG_PL2303_EPBULKOUT=2
 367 CONFIG_PL2303_EPBULKIN=3
 368 CONFIG_PL2303_NWRREQS=4
 369 CONFIG_PL2303_NRDREQS=4
 370 CONFIG_PL2303_VENDORID=0x067b
 371 CONFIG_PL2303_PRODUCTID=0x2303
 372 CONFIG_PL2303_VENDORSTR="Nuttx"
 373 CONFIG_PL2303_PRODUCTSTR="USBdev Serial"
 374 CONFIG_PL2303_RXBUFSIZE=512
 375 CONFIG_PL2303_TXBUFSIZE=512
 376
 377 #
 378 # USB Storage Device Configuration
 379 #
 380 CONFIG_USBMSC=n
 381 CONFIG_USBMSC_EP0MAXPACKET=64
 382 CONFIG_USBMSC_EPBULKOUT=2
 383 CONFIG_USBMSC_EPBULKIN=5
 384 CONFIG_USBMSC_NRDREQS=2
 385 CONFIG_USBMSC_NWRREQS=2
 386 CONFIG_USBMSC_BULKINREQLEN=256
 387 CONFIG_USBMSC_BULKOUTREQLEN=256
 388 CONFIG_USBMSC_VENDORID=0x584e
 389 CONFIG_USBMSC_VENDORSTR="NuttX"
 390 CONFIG_USBMSC_PRODUCTID=0x5342
 391 CONFIG_USBMSC_PRODUCTSTR="USBdev Storage"
 392 CONFIG_USBMSC_VERSIONNO=0x0399
 393 CONFIG_USBMSC_REMOVABLE=y
 394
 395 #
 396 # Watchdog timer configuration
 397 #
 398 CONFIG_WATCHDOG=n
 399
 400 #
 401 # Graphics related configuration settings
 402 #
 403 CONFIG_NX=y
 404 CONFIG_NX_MULTIUSER=n
 405 CONFIG_NX_NPLANES=1
 406 CONFIG_NX_DISABLE_1BPP=y
 407 CONFIG_NX_DISABLE_2BPP=y
 408 CONFIG_NX_DISABLE_4BPP=y
 409 CONFIG_NX_DISABLE_8BPP=y
 410 CONFIG_NX_DISABLE_16BPP=n
 411 CONFIG_NX_DISABLE_24BPP=y
 412 CONFIG_NX_DISABLE_32BPP=y
 413 CONFIG_NX_PACKEDMSFIRST=n
 414 CONFIG_NX_LCDDRIVER=y
 415
 416 CONFIG_NX_MOUSE=y
 417 CONFIG_NX_KBD=y
 418 #CONFIG_NXTK_BORDERWIDTH=4
 419 CONFIG_NXTK_BORDERCOLOR1=0xd69a
 420 CONFIG_NXTK_BORDERCOLOR2=0xad55
 421 CONFIG_NXFONT_SANS22X29=n
 422 CONFIG_NXFONT_SANS23X27=y
 423 CONFIG_NXFONT_SANS28X37=n
 424 CONFIG_NXFONT_SANS22X29B=n
 425 CONFIG_NXFONT_SANS28X37B=n
 426 CONFIG_NXFONT_SANS40X49B=n
 427 CONFIG_NXFONT_SERIF22X29=n
 428 CONFIG_NXFONT_SERIF29X37=n
 429 CONFIG_NXFONT_SERIF38X48=n
 430 CONFIG_NXFONT_SERIF22X28B=y
 431 CONFIG_NXFONT_SERIF27X38B=n
 432 CONFIG_NXFONT_SERIF38X49B=n
 433 CONFIG_NXFONTS_CHARBITS=7
 434 CONFIG_NX_BLOCKING=y
 435 CONFIG_NX_MXSERVERMSGS=32
 436 CONFIG_NX_MXCLIENTMSGS=16
 437
 438 #
 439 # LCD Hardware Configuration
 440 #
 441 CONFIG_LCD_LANDSCAPE=y
 442 CONFIG_LCD_PORTRAIT=n
 443 CONFIG_LCD_RPORTRAIT=n
 444 CONFIG_LCD_BACKLIGHT=y
 445
 446 # Configurable steps for the LCD backlight
 447 CONFIG_LCD_MAXPOWER=100
 448
 449 # Not used
 450 CONFIG_LCD_MAXCONTRAST=100
 451
 452 #
 453 # Settings for apps/nshlib
 454 #
 455 CONFIG_NSH_FILEIOSIZE=512
 456 CONFIG_NSH_STRERROR=n
 457 CONFIG_NSH_LINELEN=64
 458 CONFIG_NSH_NESTDEPTH=3
 459 CONFIG_NSH_DISABLESCRIPT=n
 460 CONFIG_NSH_DISABLEBG=n
 461 CONFIG_NSH_ROMFSETC=n
 462 CONFIG_NSH_CONSOLE=y
 463 CONFIG_NSH_CONDEV="/dev/ttyS1"
 464 CONFIG_NSH_TELNET=n
 465 CONFIG_NSH_ARCHINIT=y
 466 CONFIG_NSH_IOBUFFER_SIZE=512
 467 CONFIG_NSH_DHCPC=n
 468 CONFIG_NSH_NOMAC=n
 469 CONFIG_NSH_IPADDR=0x0a000002
 470 CONFIG_NSH_DRIPADDR=0x0a000001
 471 CONFIG_NSH_NETMASK=0xffffff00
 472 CONFIG_NSH_ROMFSMOUNTPT="/etc"
 473 CONFIG_NSH_INITSCRIPT="init.d/rcS"
 474 CONFIG_NSH_ROMFSDEVNO=0
 475 CONFIG_NSH_ROMFSSECTSIZE=64
 476 CONFIG_NSH_FATDEVNO=1
 477 CONFIG_NSH_FATSECTSIZE=512
 478 CONFIG_NSH_FATNSECTORS=1024
 479 CONFIG_NSH_FATMOUNTPT=/tmp
 480
 481 #
 482 # Architecture-specific NSH options
 483 #
 484 CONFIG_NSH_MMCSDSPIPORTNO=0
 485 CONFIG_NSH_MMCSDSLOTNO=0
 486 CONFIG_NSH_MMCSDMINOR=0
 487
 488 #
 489 # Settings for examples/usbserial
 490 #
 491 CONFIG_EXAMPLES_USBSERIAL_INONLY=n
 492 CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
 493 CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
 494 CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
 495
 496 CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
 497 CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
 498 CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
 499 CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
 500 CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
 501
 502 #
 503 # Settings for examples/nx
 504 #
 505 CONFIG_EXAMPLES_NX_BUILTIN=n
 506 CONFIG_EXAMPLES_NX_VPLANE=0
 507 CONFIG_EXAMPLES_NX_DEVNO=0
 508 CONFIG_EXAMPLES_NX_BGCOLOR=0x0011
 509 CONFIG_EXAMPLES_NX_COLOR1=0xaedc
 510 CONFIG_EXAMPLES_NX_COLOR2=0xe7ff
 511 CONFIG_EXAMPLES_NX_TBCOLOR=0xd69a
 512 CONFIG_EXAMPLES_NX_FONTID=0
 513 CONFIG_EXAMPLES_NX_FONTCOLOR=0x0000
 514 CONFIG_EXAMPLES_NX_BPP=16
 515 CONFIG_EXAMPLES_NX_RAWWINDOWS=n
 516 CONFIG_EXAMPLES_NX_STACKSIZE=2048
 517 CONFIG_EXAMPLES_NX_CLIENTPRIO=80
 518 CONFIG_EXAMPLES_NX_SERVERPRIO=120
 519 CONFIG_EXAMPLES_NX_NOTIFYSIGNO=4
 520 CONFIG_EXAMPLES_NX_EXTERNINIT=n
 521
 522 #
 523 # Settings for examples/nxtext
 524 #
 525 CONFIG_EXAMPLES_NXTEXT_BUILTIN=n
 526 CONFIG_EXAMPLES_NXTEXT_VPLANE=0
 527 CONFIG_EXAMPLES_NXTEXT_DEVNO=0
 528 CONFIG_EXAMPLES_NXTEXT_BGCOLOR=0x0011
 529 CONFIG_EXAMPLES_NXTEXT_BGFONTID=11
 530 CONFIG_EXAMPLES_NXTEXT_BGFONTCOLOR=0xffdf
 531 CONFIG_EXAMPLES_NXTEXT_PUCOLOR=0xfd20
 532 CONFIG_EXAMPLES_NXTEXT_PUFONTID=1
 533 CONFIG_EXAMPLES_NXTEXT_PUFONTCOLOR=0x001f
 534 CONFIG_EXAMPLES_NXTEXT_BPP=16
 535 CONFIG_EXAMPLES_NXTEXT_NOGETRUN=y
 536 CONFIG_EXAMPLES_NXTEXT_EXTERNINIT=n
 537 CONFIG_EXAMPLES_NXTEXT_BMCACHE=512
 538 CONFIG_EXAMPLES_NXTEXT_GLCACHE=16
 539 CONFIG_EXAMPLES_NXTEXT_STACKSIZE=2048
 540 CONFIG_EXAMPLES_NXTEXT_CLIENTPRIO=80
 541 CONFIG_EXAMPLES_NXTEXT_SERVERPRIO=120
 542 CONFIG_EXAMPLES_NXTEXT_NOTIFYSIGNO=4
 543
 544 #
 545 # Settings for examples/nximage
 546 #
 547 CONFIG_EXAMPLES_NXIMAGE_BUILTIN=n
 548 CONFIG_EXAMPLES_NXIMAGE_VPLANE=0
 549 CONFIG_EXAMPLES_NXIMAGE_DEVNO=0
 550 CONFIG_EXAMPLES_NXIMAGE_BPP=16
 551 CONFIG_EXAMPLES_NXIMAGE_XSCALEp5=n
 552 CONFIG_EXAMPLES_NXIMAGE_XSCALE1p5=y
 553 CONFIG_EXAMPLES_NXIMAGE_XSCALE2p0=n
 554 CONFIG_EXAMPLES_NXIMAGE_YSCALEp5=n
 555 CONFIG_EXAMPLES_NXIMAGE_YSCALE1p5=y
 556 CONFIG_EXAMPLES_NXIMAGE_YSCALE2p0=n
 557 CONFIG_EXAMPLES_NXIMAGE_EXTERNINIT=n
 558
 559 #
 560 # Settings for examples/nxlines
 561 #
 562 CONFIG_EXAMPLES_NXLINES_BUILTIN=n
 563 CONFIG_EXAMPLES_NXLINES_VPLANE=0
 564 CONFIG_EXAMPLES_NXLINES_DEVNO=0
 565 CONFIG_EXAMPLES_NXLINES_BGCOLOR=0x0320
 566 CONFIG_EXAMPLES_NXLINES_LINEWIDTH=16
 567 CONFIG_EXAMPLES_NXLINES_LINECOLOR=0xffe0
 568 CONFIG_EXAMPLES_NXLINES_BORDERWIDTH=4
 569 CONFIG_EXAMPLES_NXLINES_BORDERCOLOR=0xffe0
 570 CONFIG_EXAMPLES_NXLINES_CIRCLECOLOR=0xf7bb
 571 CONFIG_EXAMPLES_NXLINES_BPP=16
 572 CONFIG_EXAMPLES_NXLINES_EXTERNINIT=n
 573
 574 #
 575 # Settings for examples/watchdog
 576 #
 577 # This test depends on these specific Watchdog/NSH configurations settings (your
 578 # specific watchdog hardware settings might require additional settings).
 579 #
 580
 581 #
 582 # Stack and heap information
 583 #
 584 CONFIG_BOOT_RUNFROMFLASH=n
 585 CONFIG_BOOT_COPYTORAM=n
 586 CONFIG_CUSTOM_STACK=n
 587 #CONFIG_STACK_POINTER
 588 CONFIG_IDLETHREAD_STACKSIZE=1024
 589 CONFIG_USERMAIN_STACKSIZE=2048
 590 CONFIG_PTHREAD_STACK_MIN=256
 591 CONFIG_PTHREAD_STACK_DEFAULT=2048
 592 CONFIG_HEAP_BASE=
 593 CONFIG_HEAP_SIZE=