drivers/usb/serial/ftdi_sio.h

   1 /*
   2  * Definitions for the FTDI USB Single Port Serial Converter -
   3  * known as FTDI_SIO (Serial Input/Output application of the chipset)
   4  *
   5  * The example I have is known as the USC-1000 which is available from
   6  * http://www.dse.co.nz - cat no XH4214 It looks similar to this:
   7  * http://www.dansdata.com/usbser.htm but I can't be sure There are other
   8  * USC-1000s which don't look like my device though so beware!
   9  *
  10  * The device is based on the FTDI FT8U100AX chip. It has a DB25 on one side,
  11  * USB on the other.
  12  *
  13  * Thanx to FTDI (http://www.ftdi.co.uk) for so kindly providing details
  14  * of the protocol required to talk to the device and ongoing assistence
  15  * during development.
  16  *
  17  * Bill Ryder - bryder@sgi.com formerly of Silicon Graphics, Inc.- wrote the
  18  * FTDI_SIO implementation.
  19  *
  20  * Philipp Gühring - pg@futureware.at - added the Device ID of the USB relais
  21  * from Rudolf Gugler
  22  *
  23  */
  24
  25 #define FTDI_VID        0x0403  /* Vendor Id */
  26 #define FTDI_SIO_PID    0x8372  /* Product Id SIO application of 8U100AX  */
  27 #define FTDI_8U232AM_PID 0x6001 /* Similar device to SIO above */
  28 #define FTDI_8U232AM_ALT_PID 0x6006 /* FTDI's alternate PID for above */
  29 #define FTDI_8U2232C_PID 0x6010 /* Dual channel device */
  30 #define FTDI_RELAIS_PID 0xFA10  /* Relais device from Rudolf Gugler */
  31 #define FTDI_NF_RIC_VID 0x0DCD  /* Vendor Id */
  32 #define FTDI_NF_RIC_PID 0x0001  /* Product Id */
  33
  34
  35 /* www.irtrans.de device */
  36 #define FTDI_IRTRANS_PID 0xFC60 /* Product Id */
  37
  38
  39 /* www.thoughttechnology.com/ TT-USB provide with procomp use ftdi_sio */
  40 #define FTDI_TTUSB_PID 0xFF20 /* Product Id */
  41
  42 /* www.crystalfontz.com devices - thanx for providing free devices for evaluation ! */
  43 /* they use the ftdi chipset for the USB interface and the vendor id is the same */
  44 #define FTDI_XF_632_PID 0xFC08  /* 632: 16x2 Character Display */
  45 #define FTDI_XF_634_PID 0xFC09  /* 634: 20x4 Character Display */
  46 #define FTDI_XF_547_PID 0xFC0A  /* 547: Two line Display */
  47 #define FTDI_XF_633_PID 0xFC0B  /* 633: 16x2 Character Display with Keys */
  48 #define FTDI_XF_631_PID 0xFC0C  /* 631: 20x2 Character Display */
  49 #define FTDI_XF_635_PID 0xFC0D  /* 635: 20x4 Character Display */
  50 #define FTDI_XF_640_PID 0xFC0E  /* 640: Two line Display */
  51 #define FTDI_XF_642_PID 0xFC0F  /* 642: Two line Display */
  52
  53 /* Video Networks Limited / Homechoice in the UK use an ftdi-based device for their 1Mb */
  54 /* broadband internet service.  The following PID is exhibited by the usb device supplied */
  55 /* (the VID is the standard ftdi vid (FTDI_VID) */
  56 #define FTDI_VNHCPCUSB_D_PID 0xfe38 /* Product Id */
  57
  58 /*
  59  * PCDJ use ftdi based dj-controllers.  The following PID is for their DAC-2 device
  60  * http://www.pcdjhardware.com/DAC2.asp (PID sent by Wouter Paesen)
  61  * (the VID is the standard ftdi vid (FTDI_VID) */
  62 #define FTDI_PCDJ_DAC2_PID 0xFA88
  63
  64 /*
  65  * The following are the values for the Matrix Orbital LCD displays,
  66  * which are the FT232BM ( similar to the 8U232AM )
  67  */
  68 #define FTDI_MTXORB_0_PID      0xFA00  /* Matrix Orbital Product Id */
  69 #define FTDI_MTXORB_1_PID      0xFA01  /* Matrix Orbital Product Id */
  70 #define FTDI_MTXORB_2_PID      0xFA02  /* Matrix Orbital Product Id */
  71 #define FTDI_MTXORB_3_PID      0xFA03  /* Matrix Orbital Product Id */
  72 #define FTDI_MTXORB_4_PID      0xFA04  /* Matrix Orbital Product Id */
  73 #define FTDI_MTXORB_5_PID      0xFA05  /* Matrix Orbital Product Id */
  74 #define FTDI_MTXORB_6_PID      0xFA06  /* Matrix Orbital Product Id */
  75
  76 /* Interbiometrics USB I/O Board */
  77 /* Developed for Interbiometrics by Rudolf Gugler */
  78 #define INTERBIOMETRICS_VID              0x1209
  79 #define INTERBIOMETRICS_IOBOARD_PID      0x1002
  80 #define INTERBIOMETRICS_MINI_IOBOARD_PID 0x1006
  81
  82 /*
  83  * The following are the values for the Perle Systems
  84  * UltraPort USB serial converters
  85  */
  86 #define FTDI_PERLE_ULTRAPORT_PID 0xF0C0 /* Perle UltraPort Product Id */
  87
  88 /*
  89  * The following are the values for the Sealevel SeaLINK+ adapters.
  90  * (Original list sent by Tuan Hoang.  Ian Abbott renamed the macros and
  91  * removed some PIDs that don't seem to match any existing products.)
  92  */
  93 #define SEALEVEL_VID            0x0c52  /* Sealevel Vendor ID */
  94 #define SEALEVEL_2101_PID       0x2101  /* SeaLINK+232 (2101/2105) */
  95 #define SEALEVEL_2102_PID       0x2102  /* SeaLINK+485 (2102) */
  96 #define SEALEVEL_2103_PID       0x2103  /* SeaLINK+232I (2103) */
  97 #define SEALEVEL_2104_PID       0x2104  /* SeaLINK+485I (2104) */
  98 #define SEALEVEL_2201_1_PID     0x2211  /* SeaPORT+2/232 (2201) Port 1 */
  99 #define SEALEVEL_2201_2_PID     0x2221  /* SeaPORT+2/232 (2201) Port 2 */
 100 #define SEALEVEL_2202_1_PID     0x2212  /* SeaPORT+2/485 (2202) Port 1 */
 101 #define SEALEVEL_2202_2_PID     0x2222  /* SeaPORT+2/485 (2202) Port 2 */
 102 #define SEALEVEL_2203_1_PID     0x2213  /* SeaPORT+2 (2203) Port 1 */
 103 #define SEALEVEL_2203_2_PID     0x2223  /* SeaPORT+2 (2203) Port 2 */
 104 #define SEALEVEL_2401_1_PID     0x2411  /* SeaPORT+4/232 (2401) Port 1 */
 105 #define SEALEVEL_2401_2_PID     0x2421  /* SeaPORT+4/232 (2401) Port 2 */
 106 #define SEALEVEL_2401_3_PID     0x2431  /* SeaPORT+4/232 (2401) Port 3 */
 107 #define SEALEVEL_2401_4_PID     0x2441  /* SeaPORT+4/232 (2401) Port 4 */
 108 #define SEALEVEL_2402_1_PID     0x2412  /* SeaPORT+4/485 (2402) Port 1 */
 109 #define SEALEVEL_2402_2_PID     0x2422  /* SeaPORT+4/485 (2402) Port 2 */
 110 #define SEALEVEL_2402_3_PID     0x2432  /* SeaPORT+4/485 (2402) Port 3 */
 111 #define SEALEVEL_2402_4_PID     0x2442  /* SeaPORT+4/485 (2402) Port 4 */
 112 #define SEALEVEL_2403_1_PID     0x2413  /* SeaPORT+4 (2403) Port 1 */
 113 #define SEALEVEL_2403_2_PID     0x2423  /* SeaPORT+4 (2403) Port 2 */
 114 #define SEALEVEL_2403_3_PID     0x2433  /* SeaPORT+4 (2403) Port 3 */
 115 #define SEALEVEL_2403_4_PID     0x2443  /* SeaPORT+4 (2403) Port 4 */
 116 #define SEALEVEL_2801_1_PID     0X2811  /* SeaLINK+8/232 (2801) Port 1 */
 117 #define SEALEVEL_2801_2_PID     0X2821  /* SeaLINK+8/232 (2801) Port 2 */
 118 #define SEALEVEL_2801_3_PID     0X2831  /* SeaLINK+8/232 (2801) Port 3 */
 119 #define SEALEVEL_2801_4_PID     0X2841  /* SeaLINK+8/232 (2801) Port 4 */
 120 #define SEALEVEL_2801_5_PID     0X2851  /* SeaLINK+8/232 (2801) Port 5 */
 121 #define SEALEVEL_2801_6_PID     0X2861  /* SeaLINK+8/232 (2801) Port 6 */
 122 #define SEALEVEL_2801_7_PID     0X2871  /* SeaLINK+8/232 (2801) Port 7 */
 123 #define SEALEVEL_2801_8_PID     0X2881  /* SeaLINK+8/232 (2801) Port 8 */
 124 #define SEALEVEL_2802_1_PID     0X2812  /* SeaLINK+8/485 (2802) Port 1 */
 125 #define SEALEVEL_2802_2_PID     0X2822  /* SeaLINK+8/485 (2802) Port 2 */
 126 #define SEALEVEL_2802_3_PID     0X2832  /* SeaLINK+8/485 (2802) Port 3 */
 127 #define SEALEVEL_2802_4_PID     0X2842  /* SeaLINK+8/485 (2802) Port 4 */
 128 #define SEALEVEL_2802_5_PID     0X2852  /* SeaLINK+8/485 (2802) Port 5 */
 129 #define SEALEVEL_2802_6_PID     0X2862  /* SeaLINK+8/485 (2802) Port 6 */
 130 #define SEALEVEL_2802_7_PID     0X2872  /* SeaLINK+8/485 (2802) Port 7 */
 131 #define SEALEVEL_2802_8_PID     0X2882  /* SeaLINK+8/485 (2802) Port 8 */
 132 #define SEALEVEL_2803_1_PID     0X2813  /* SeaLINK+8 (2803) Port 1 */
 133 #define SEALEVEL_2803_2_PID     0X2823  /* SeaLINK+8 (2803) Port 2 */
 134 #define SEALEVEL_2803_3_PID     0X2833  /* SeaLINK+8 (2803) Port 3 */
 135 #define SEALEVEL_2803_4_PID     0X2843  /* SeaLINK+8 (2803) Port 4 */
 136 #define SEALEVEL_2803_5_PID     0X2853  /* SeaLINK+8 (2803) Port 5 */
 137 #define SEALEVEL_2803_6_PID     0X2863  /* SeaLINK+8 (2803) Port 6 */
 138 #define SEALEVEL_2803_7_PID     0X2873  /* SeaLINK+8 (2803) Port 7 */
 139 #define SEALEVEL_2803_8_PID     0X2883  /* SeaLINK+8 (2803) Port 8 */
 140
 141 /*
 142  * The following are the values for two KOBIL chipcard terminals.
 143  */
 144 #define KOBIL_VID               0x0d46  /* KOBIL Vendor ID */
 145 #define KOBIL_CONV_B1_PID       0x2020  /* KOBIL Konverter for B1 */
 146 #define KOBIL_CONV_KAAN_PID     0x2021  /* KOBIL_Konverter for KAAN */
 147
 148 /*
 149  * DSS-20 Sync Station for Sony Ericsson P800
 150  */
 151
 152 #define FTDI_DSS20_PID          0xFC82
 153
 154 /*
 155  * Home Electronics (www.home-electro.com) USB gadgets
 156  */
 157 #define FTDI_HE_TIRA1_PID       0xFA78  /* Tira-1 IR transceiver */
 158
 159 /* USB-UIRT - An infrared receiver and transmitter using the 8U232AM chip */
 160 /* http://home.earthlink.net/~jrhees/USBUIRT/index.htm */
 161 #define FTDI_USB_UIRT_PID       0xF850  /* Product Id */
 162
 163 /*
 164  * ELV USB devices submitted by Christian Abt of ELV (www.elv.de).
 165  * All of these devices use FTDI's vendor ID (0x0403).
 166  *
 167  * The previously included PID for the UO 100 module was incorrect.
 168  * In fact, that PID was for ELV's UR 100 USB-RS232 converter (0xFB58).
 169  *
 170  * Armin Laeuger originally sent the PID for the UM 100 module.
 171  */
 172 #define FTDI_ELV_UR100_PID      0xFB58  /* USB-RS232-Umsetzer (UR 100) */
 173 #define FTDI_ELV_UM100_PID      0xFB5A  /* USB-Modul UM 100 */
 174 #define FTDI_ELV_UO100_PID      0xFB5B  /* USB-Modul UO 100 */
 175 #define FTDI_ELV_ALC8500_PID    0xF06E  /* ALC 8500 Expert */
 176 /* Additional ELV PIDs that default to using the FTDI D2XX drivers on
 177  * MS Windows, rather than the FTDI Virtual Com Port drivers.
 178  * Maybe these will be easier to use with the libftdi/libusb user-space
 179  * drivers, or possibly the Comedi drivers in some cases. */
 180 #define FTDI_ELV_CLI7000_PID    0xFB59  /* Computer-Light-Interface (CLI 7000) */
 181 #define FTDI_ELV_PPS7330_PID    0xFB5C  /* Processor-Power-Supply (PPS 7330) */
 182 #define FTDI_ELV_TFM100_PID     0xFB5D  /* Temperartur-Feuchte Messgeraet (TFM 100) */
 183 #define FTDI_ELV_UDF77_PID      0xFB5E  /* USB DCF Funkurh (UDF 77) */
 184 #define FTDI_ELV_UIO88_PID      0xFB5F  /* USB-I/O Interface (UIO 88) */
 185 #define FTDI_ELV_UAD8_PID       0xF068  /* USB-AD-Wandler (UAD 8) */
 186 #define FTDI_ELV_UDA7_PID       0xF069  /* USB-DA-Wandler (UDA 7) */
 187 #define FTDI_ELV_USI2_PID       0xF06A  /* USB-Schrittmotoren-Interface (USI 2) */
 188 #define FTDI_ELV_T1100_PID      0xF06B  /* Thermometer (T 1100) */
 189 #define FTDI_ELV_PCD200_PID     0xF06C  /* PC-Datenlogger (PCD 200) */
 190 #define FTDI_ELV_ULA200_PID     0xF06D  /* USB-LCD-Ansteuerung (ULA 200) */
 191 #define FTDI_ELV_FHZ1000PC_PID  0xF06F  /* FHZ 1000 PC */
 192 #define FTDI_ELV_CSI8_PID       0xE0F0  /* Computer-Schalt-Interface (CSI 8) */
 193 #define FTDI_ELV_EM1000DL_PID   0xE0F1  /* PC-Datenlogger fuer Energiemonitor (EM 1000 DL) */
 194 #define FTDI_ELV_PCK100_PID     0xE0F2  /* PC-Kabeltester (PCK 100) */
 195 #define FTDI_ELV_RFP500_PID     0xE0F3  /* HF-Leistungsmesser (RFP 500) */
 196 #define FTDI_ELV_FS20SIG_PID    0xE0F4  /* Signalgeber (FS 20 SIG) */
 197 #define FTDI_ELV_WS300PC_PID    0xE0F6  /* PC-Wetterstation (WS 300 PC) */
 198 #define FTDI_ELV_FHZ1300PC_PID  0xE0E8  /* FHZ 1300 PC */
 199 #define FTDI_ELV_WS500_PID      0xE0E9  /* PC-Wetterstation (WS 500) */
 200
 201 /*
 202  * Definitions for ID TECH (www.idt-net.com) devices
 203  */
 204 #define IDTECH_VID              0x0ACD  /* ID TECH Vendor ID */
 205 #define IDTECH_IDT1221U_PID     0x0300  /* IDT1221U USB to RS-232 adapter */
 206
 207 /*
 208  * Definitions for Omnidirectional Control Technology, Inc. devices
 209  */
 210 #define OCT_VID                 0x0B39  /* OCT vendor ID */
 211 /* Note: OCT US101 is also rebadged as Dick Smith Electronics (NZ) XH6381 */
 212 /* Also rebadged as Dick Smith Electronics (Aus) XH6451 */
 213 /* Also rebadged as SIIG Inc. model US2308 hardware version 1 */
 214 #define OCT_US101_PID           0x0421  /* OCT US101 USB to RS-232 */
 215
 216 /* an infrared receiver for user access control with IR tags */
 217 #define FTDI_PIEGROUP_PID       0xF208  /* Product Id */
 218
 219 /*
 220  * Definitions for Artemis astronomical USB based cameras
 221  * Check it at http://www.artemisccd.co.uk/
 222  */
 223 #define FTDI_ARTEMIS_PID        0xDF28  /* All Artemis Cameras */
 224
 225 /*
 226  * Definitions for ATIK Instruments astronomical USB based cameras
 227  * Check it at http://www.atik-instruments.com/
 228  */
 229 #define FTDI_ATIK_ATK16_PID     0xDF30  /* ATIK ATK-16 Camera */
 230 #define FTDI_ATIK_ATK16HR_PID   0xDF31  /* ATIK ATK-16HR Camera */
 231
 232 /*
 233  * Protego product ids
 234  */
 235 #define PROTEGO_SPECIAL_1       0xFC70  /* special/unknown device */
 236 #define PROTEGO_R2X0            0xFC71  /* R200-USB TRNG unit (R210, R220, and R230) */
 237 #define PROTEGO_SPECIAL_3       0xFC72  /* special/unknown device */
 238 #define PROTEGO_SPECIAL_4       0xFC73  /* special/unknown device */
 239
 240 /*
 241  * Gude Analog- und Digitalsysteme GmbH
 242  */
 243 #define FTDI_GUDEADS_E808_PID    0xE808
 244 #define FTDI_GUDEADS_E809_PID    0xE809
 245 #define FTDI_GUDEADS_E80A_PID    0xE80A
 246 #define FTDI_GUDEADS_E80B_PID    0xE80B
 247 #define FTDI_GUDEADS_E80C_PID    0xE80C
 248 #define FTDI_GUDEADS_E80D_PID    0xE80D
 249 #define FTDI_GUDEADS_E80E_PID    0xE80E
 250 #define FTDI_GUDEADS_E80F_PID    0xE80F
 251 #define FTDI_GUDEADS_E888_PID    0xE888  /* Expert ISDN Control USB */
 252 #define FTDI_GUDEADS_E889_PID    0xE889  /* USB RS-232 OptoBridge */
 253 #define FTDI_GUDEADS_E88A_PID    0xE88A
 254 #define FTDI_GUDEADS_E88B_PID    0xE88B
 255 #define FTDI_GUDEADS_E88C_PID    0xE88C
 256 #define FTDI_GUDEADS_E88D_PID    0xE88D
 257 #define FTDI_GUDEADS_E88E_PID    0xE88E
 258 #define FTDI_GUDEADS_E88F_PID    0xE88F
 259
 260 /*
 261  * Linx Technologies product ids
 262  */
 263 #define LINX_SDMUSBQSS_PID      0xF448  /* Linx SDM-USB-QS-S */
 264 #define LINX_MASTERDEVEL2_PID   0xF449   /* Linx Master Development 2.0 */
 265 #define LINX_FUTURE_0_PID   0xF44A   /* Linx future device */
 266 #define LINX_FUTURE_1_PID   0xF44B   /* Linx future device */
 267 #define LINX_FUTURE_2_PID   0xF44C   /* Linx future device */
 268
 269 /* CCS Inc. ICDU/ICDU40 product ID - the FT232BM is used in an in-circuit-debugger */
 270 /* unit for PIC16's/PIC18's */
 271 #define FTDI_CCSICDU20_0_PID    0xF9D0
 272 #define FTDI_CCSICDU40_1_PID    0xF9D1
 273
 274 /* Inside Accesso contactless reader (http://www.insidefr.com) */
 275 #define INSIDE_ACCESSO          0xFAD0
 276
 277 /*
 278  * Intrepid Control Systems (http://www.intrepidcs.com/) ValueCAN and NeoVI
 279  */
 280 #define INTREPID_VID            0x093C
 281 #define INTREPID_VALUECAN_PID   0x0601
 282 #define INTREPID_NEOVI_PID      0x0701
 283
 284 /*
 285  * Falcom Wireless Communications GmbH
 286  */
 287 #define FALCOM_VID              0x0F94  /* Vendor Id */
 288 #define FALCOM_TWIST_PID        0x0001  /* Falcom Twist USB GPRS modem */
 289 #define FALCOM_SAMBA_PID        0x0005  /* Falcom Samba USB GPRS modem */
 290
 291 /*
 292  * SUUNTO product ids
 293  */
 294 #define FTDI_SUUNTO_SPORTS_PID  0xF680  /* Suunto Sports instrument */
 295
 296 /*
 297  * Definitions for B&B Electronics products.
 298  */
 299 #define BANDB_VID               0x0856  /* B&B Electronics Vendor ID */
 300 #define BANDB_USOTL4_PID        0xAC01  /* USOTL4 Isolated RS-485 Converter */
 301 #define BANDB_USTL4_PID         0xAC02  /* USTL4 RS-485 Converter */
 302 #define BANDB_USO9ML2_PID       0xAC03  /* USO9ML2 Isolated RS-232 Converter */
 303
 304 /*
 305  * RM Michaelides CANview USB (http://www.rmcan.com)
 306  * CAN fieldbus interface adapter, added by port GmbH www.port.de)
 307  * Ian Abbott changed the macro names for consistency.
 308  */
 309 #define FTDI_RM_CANVIEW_PID     0xfd60  /* Product Id */
 310
 311 /*
 312  * EVER Eco Pro UPS (http://www.ever.com.pl/)
 313  */
 314
 315 #define EVER_ECO_PRO_CDS        0xe520  /* RS-232 converter */
 316
 317 /*
 318  * 4N-GALAXY.DE PIDs for CAN-USB, USB-RS232, USB-RS422, USB-RS485,
 319  * USB-TTY activ, USB-TTY passiv.  Some PIDs are used by several devices
 320  * and I'm not entirely sure which are used by which.
 321  */
 322 #define FTDI_4N_GALAXY_DE_0_PID 0x8372
 323 #define FTDI_4N_GALAXY_DE_1_PID 0xF3C0
 324 #define FTDI_4N_GALAXY_DE_2_PID 0xF3C1
 325
 326 /*
 327  * Mobility Electronics products.
 328  */
 329 #define MOBILITY_VID                    0x1342
 330 #define MOBILITY_USB_SERIAL_PID         0x0202  /* EasiDock USB 200 serial */
 331
 332 /*
 333  * microHAM product IDs (http://www.microham.com).
 334  * Submitted by Justin Burket (KL1RL) <zorton@jtan.com>.
 335  */
 336 #define FTDI_MHAM_Y6_PID 0xEEEA         /* USB-Y6 interface */
 337 #define FTDI_MHAM_Y8_PID 0xEEEB         /* USB-Y8 interface */
 338
 339 /*
 340  * Active Robots product ids.
 341  */
 342 #define FTDI_ACTIVE_ROBOTS_PID  0xE548  /* USB comms board */
 343
 344 /*
 345  * Xsens Technologies BV products (http://www.xsens.com).
 346  */
 347 #define XSENS_CONVERTER_0_PID   0xD388
 348 #define XSENS_CONVERTER_1_PID   0xD389
 349 #define XSENS_CONVERTER_2_PID   0xD38A
 350 #define XSENS_CONVERTER_3_PID   0xD38B
 351 #define XSENS_CONVERTER_4_PID   0xD38C
 352 #define XSENS_CONVERTER_5_PID   0xD38D
 353 #define XSENS_CONVERTER_6_PID   0xD38E
 354 #define XSENS_CONVERTER_7_PID   0xD38F
 355
 356 /*
 357  * Teratronik product ids.
 358  * Submitted by O. Wölfelschneider.
 359  */
 360 #define FTDI_TERATRONIK_VCP_PID  0xEC88 /* Teratronik device (preferring VCP driver on windows) */
 361 #define FTDI_TERATRONIK_D2XX_PID 0xEC89 /* Teratronik device (preferring D2XX driver on windows) */
 362
 363 /*
 364  * Evolution Robotics products (http://www.evolution.com/).
 365  * Submitted by Shawn M. Lavelle.
 366  */
 367 #define EVOLUTION_VID           0xDEEE  /* Vendor ID */
 368 #define EVOLUTION_ER1_PID       0x0300  /* ER1 Control Module */
 369
 370 /* Pyramid Computer GmbH */
 371 #define FTDI_PYRAMID_PID        0xE6C8  /* Pyramid Appliance Display */
 372
 373 /*
 374  * Posiflex inc retail equipment (http://www.posiflex.com.tw)
 375  */
 376 #define POSIFLEX_VID            0x0d3a  /* Vendor ID */
 377 #define POSIFLEX_PP7000_PID     0x0300  /* PP-7000II thermal printer */
 378
 379 /*
 380  * Westrex International devices submitted by Cory Lee
 381  */
 382 #define FTDI_WESTREX_MODEL_777_PID      0xDC00  /* Model 777 */
 383 #define FTDI_WESTREX_MODEL_8900F_PID    0xDC01  /* Model 8900F */
 384
 385 /* Commands */
 386 #define FTDI_SIO_RESET          0 /* Reset the port */
 387 #define FTDI_SIO_MODEM_CTRL     1 /* Set the modem control register */
 388 #define FTDI_SIO_SET_FLOW_CTRL  2 /* Set flow control register */
 389 #define FTDI_SIO_SET_BAUD_RATE  3 /* Set baud rate */
 390 #define FTDI_SIO_SET_DATA       4 /* Set the data characteristics of the port */
 391 #define FTDI_SIO_GET_MODEM_STATUS       5 /* Retrieve current value of modern status register */
 392 #define FTDI_SIO_SET_EVENT_CHAR 6 /* Set the event character */
 393 #define FTDI_SIO_SET_ERROR_CHAR 7 /* Set the error character */
 394 #define FTDI_SIO_SET_LATENCY_TIMER      9 /* Set the latency timer */
 395 #define FTDI_SIO_GET_LATENCY_TIMER      10 /* Get the latency timer */
 396
 397
 398 /*
 399  *   BmRequestType:  1100 0000b
 400  *   bRequest:       FTDI_E2_READ
 401  *   wValue:         0
 402  *   wIndex:         Address of word to read
 403  *   wLength:        2
 404  *   Data:           Will return a word of data from E2Address
 405  *
 406  */
 407
 408 /* Port Identifier Table */
 409 #define PIT_DEFAULT             0 /* SIOA */
 410 #define PIT_SIOA                1 /* SIOA */
 411 /* The device this driver is tested with one has only one port */
 412 #define PIT_SIOB                2 /* SIOB */
 413 #define PIT_PARALLEL            3 /* Parallel */
 414
 415 /* FTDI_SIO_RESET */
 416 #define FTDI_SIO_RESET_REQUEST FTDI_SIO_RESET
 417 #define FTDI_SIO_RESET_REQUEST_TYPE 0x40
 418 #define FTDI_SIO_RESET_SIO 0
 419 #define FTDI_SIO_RESET_PURGE_RX 1
 420 #define FTDI_SIO_RESET_PURGE_TX 2
 421
 422 /*
 423  * BmRequestType:  0100 0000B
 424  * bRequest:       FTDI_SIO_RESET
 425  * wValue:         Control Value
 426  *                   0 = Reset SIO
 427  *                   1 = Purge RX buffer
 428  *                   2 = Purge TX buffer
 429  * wIndex:         Port
 430  * wLength:        0
 431  * Data:           None
 432  *
 433  * The Reset SIO command has this effect:
 434  *
 435  *    Sets flow control set to 'none'
 436  *    Event char = $0D
 437  *    Event trigger = disabled
 438  *    Purge RX buffer
 439  *    Purge TX buffer
 440  *    Clear DTR
 441  *    Clear RTS
 442  *    baud and data format not reset
 443  *
 444  * The Purge RX and TX buffer commands affect nothing except the buffers
 445  *
 446    */
 447
 448 /* FTDI_SIO_SET_BAUDRATE */
 449 #define FTDI_SIO_SET_BAUDRATE_REQUEST_TYPE 0x40
 450 #define FTDI_SIO_SET_BAUDRATE_REQUEST 3
 451
 452 /*
 453  * BmRequestType:  0100 0000B
 454  * bRequest:       FTDI_SIO_SET_BAUDRATE
 455  * wValue:         BaudDivisor value - see below
 456  * wIndex:         Port
 457  * wLength:        0
 458  * Data:           None
 459  * The BaudDivisor values are calculated as follows:
 460  * - BaseClock is either 12000000 or 48000000 depending on the device. FIXME: I wish
 461  *   I knew how to detect old chips to select proper base clock!
 462  * - BaudDivisor is a fixed point number encoded in a funny way.
 463  *   (--WRONG WAY OF THINKING--)
 464  *   BaudDivisor is a fixed point number encoded with following bit weighs:
 465  *   (-2)(-1)(13..0). It is a radical with a denominator of 4, so values
 466  *   end with 0.0 (00...), 0.25 (10...), 0.5 (01...), and 0.75 (11...).
 467  *   (--THE REALITY--)
 468  *   The both-bits-set has quite different meaning from 0.75 - the chip designers
 469  *   have decided it to mean 0.125 instead of 0.75.
 470  *   This info looked up in FTDI application note "FT8U232 DEVICES \ Data Rates
 471  *   and Flow Control Consideration for USB to RS232".
 472  * - BaudDivisor = (BaseClock / 16) / BaudRate, where the (=) operation should
 473  *   automagically re-encode the resulting value to take fractions into consideration.
 474  * As all values are integers, some bit twiddling is in order:
 475  *   BaudDivisor = (BaseClock / 16 / BaudRate) |
 476  *   (((BaseClock / 2 / BaudRate) & 4) ? 0x4000    // 0.5
 477  *    : ((BaseClock / 2 / BaudRate) & 2) ? 0x8000  // 0.25
 478  *    : ((BaseClock / 2 / BaudRate) & 1) ? 0xc000  // 0.125
 479  *    : 0)
 480  *
 481  * For the FT232BM, a 17th divisor bit was introduced to encode the multiples
 482  * of 0.125 missing from the FT8U232AM.  Bits 16 to 14 are coded as follows
 483  * (the first four codes are the same as for the FT8U232AM, where bit 16 is
 484  * always 0):
 485  *   000 - add .000 to divisor
 486  *   001 - add .500 to divisor
 487  *   010 - add .250 to divisor
 488  *   011 - add .125 to divisor
 489  *   100 - add .375 to divisor
 490  *   101 - add .625 to divisor
 491  *   110 - add .750 to divisor
 492  *   111 - add .875 to divisor
 493  * Bits 15 to 0 of the 17-bit divisor are placed in the urb value.  Bit 16 is
 494  * placed in bit 0 of the urb index.
 495  *
 496  * Note that there are a couple of special cases to support the highest baud
 497  * rates.  If the calculated divisor value is 1, this needs to be replaced with
 498  * 0.  Additionally for the FT232BM, if the calculated divisor value is 0x4001
 499  * (1.5), this needs to be replaced with 0x0001 (1) (but this divisor value is
 500  * not supported by the FT8U232AM).
 501  */
 502
 503 typedef enum {
 504         SIO = 1,
 505         FT8U232AM = 2,
 506         FT232BM = 3,
 507         FT2232C = 4,
 508 } ftdi_chip_type_t;
 509
 510 typedef enum {
 511  ftdi_sio_b300 = 0,
 512  ftdi_sio_b600 = 1,
 513  ftdi_sio_b1200 = 2,
 514  ftdi_sio_b2400 = 3,
 515  ftdi_sio_b4800 = 4,
 516  ftdi_sio_b9600 = 5,
 517  ftdi_sio_b19200 = 6,
 518  ftdi_sio_b38400 = 7,
 519  ftdi_sio_b57600 = 8,
 520  ftdi_sio_b115200 = 9
 521 } FTDI_SIO_baudrate_t ;
 522
 523 /*
 524  * The ftdi_8U232AM_xxMHz_byyy constants have been removed. The encoded divisor values
 525  * are calculated internally.
 526  */
 527
 528 #define FTDI_SIO_SET_DATA_REQUEST FTDI_SIO_SET_DATA
 529 #define FTDI_SIO_SET_DATA_REQUEST_TYPE 0x40
 530 #define FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8 )
 531 #define FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8 )
 532 #define FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8 )
 533 #define FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8 )
 534 #define FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8 )
 535 #define FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11 )
 536 #define FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11 )
 537 #define FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11 )
 538 #define FTDI_SIO_SET_BREAK (0x1 << 14)
 539 /* FTDI_SIO_SET_DATA */
 540
 541 /*
 542  * BmRequestType:  0100 0000B
 543  * bRequest:       FTDI_SIO_SET_DATA
 544  * wValue:         Data characteristics (see below)
 545  * wIndex:         Port
 546  * wLength:        0
 547  * Data:           No
 548  *
 549  * Data characteristics
 550  *
 551  *   B0..7   Number of data bits
 552  *   B8..10  Parity
 553  *           0 = None
 554  *           1 = Odd
 555  *           2 = Even
 556  *           3 = Mark
 557  *           4 = Space
 558  *   B11..13 Stop Bits
 559  *           0 = 1
 560  *           1 = 1.5
 561  *           2 = 2
 562  *   B14
 563  *           1 = TX ON (break)
 564  *           0 = TX OFF (normal state)
 565  *   B15 Reserved
 566  *
 567  */
 568
 569
 570
 571 /* FTDI_SIO_MODEM_CTRL */
 572 #define FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE 0x40
 573 #define FTDI_SIO_SET_MODEM_CTRL_REQUEST FTDI_SIO_MODEM_CTRL
 574
 575 /*
 576  * BmRequestType:   0100 0000B
 577  * bRequest:        FTDI_SIO_MODEM_CTRL
 578  * wValue:          ControlValue (see below)
 579  * wIndex:          Port
 580  * wLength:         0
 581  * Data:            None
 582  *
 583  * NOTE: If the device is in RTS/CTS flow control, the RTS set by this
 584  * command will be IGNORED without an error being returned
 585  * Also - you can not set DTR and RTS with one control message
 586  */
 587
 588 #define FTDI_SIO_SET_DTR_MASK 0x1
 589 #define FTDI_SIO_SET_DTR_HIGH ( 1 | ( FTDI_SIO_SET_DTR_MASK  << 8))
 590 #define FTDI_SIO_SET_DTR_LOW  ( 0 | ( FTDI_SIO_SET_DTR_MASK  << 8))
 591 #define FTDI_SIO_SET_RTS_MASK 0x2
 592 #define FTDI_SIO_SET_RTS_HIGH ( 2 | ( FTDI_SIO_SET_RTS_MASK << 8 ))
 593 #define FTDI_SIO_SET_RTS_LOW ( 0 | ( FTDI_SIO_SET_RTS_MASK << 8 ))
 594
 595 /*
 596  * ControlValue
 597  * B0    DTR state
 598  *          0 = reset
 599  *          1 = set
 600  * B1    RTS state
 601  *          0 = reset
 602  *          1 = set
 603  * B2..7 Reserved
 604  * B8    DTR state enable
 605  *          0 = ignore
 606  *          1 = use DTR state
 607  * B9    RTS state enable
 608  *          0 = ignore
 609  *          1 = use RTS state
 610  * B10..15 Reserved
 611  */
 612
 613 /* FTDI_SIO_SET_FLOW_CTRL */
 614 #define FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE 0x40
 615 #define FTDI_SIO_SET_FLOW_CTRL_REQUEST FTDI_SIO_SET_FLOW_CTRL
 616 #define FTDI_SIO_DISABLE_FLOW_CTRL 0x0
 617 #define FTDI_SIO_RTS_CTS_HS (0x1 << 8)
 618 #define FTDI_SIO_DTR_DSR_HS (0x2 << 8)
 619 #define FTDI_SIO_XON_XOFF_HS (0x4 << 8)
 620 /*
 621  *   BmRequestType:  0100 0000b
 622  *   bRequest:       FTDI_SIO_SET_FLOW_CTRL
 623  *   wValue:         Xoff/Xon
 624  *   wIndex:         Protocol/Port - hIndex is protocl / lIndex is port
 625  *   wLength:        0
 626  *   Data:           None
 627  *
 628  * hIndex protocol is:
 629  *   B0 Output handshaking using RTS/CTS
 630  *       0 = disabled
 631  *       1 = enabled
 632  *   B1 Output handshaking using DTR/DSR
 633  *       0 = disabled
 634  *       1 = enabled
 635  *   B2 Xon/Xoff handshaking
 636  *       0 = disabled
 637  *       1 = enabled
 638  *
 639  * A value of zero in the hIndex field disables handshaking
 640  *
 641  * If Xon/Xoff handshaking is specified, the hValue field should contain the XOFF character
 642  * and the lValue field contains the XON character.
 643  */
 644
 645 /*
 646  * FTDI_SIO_GET_LATENCY_TIMER
 647  *
 648  * Set the timeout interval. The FTDI collects data from the slave
 649  * device, transmitting it to the host when either A) 62 bytes are
 650  * received, or B) the timeout interval has elapsed and the buffer
 651  * contains at least 1 byte.  Setting this value to a small number
 652  * can dramatically improve performance for applications which send
 653  * small packets, since the default value is 16ms.
 654  */
 655 #define  FTDI_SIO_GET_LATENCY_TIMER_REQUEST FTDI_SIO_GET_LATENCY_TIMER
 656 #define  FTDI_SIO_GET_LATENCY_TIMER_REQUEST_TYPE 0xC0
 657
 658 /*
 659  *  BmRequestType:   1100 0000b
 660  *  bRequest:        FTDI_SIO_GET_LATENCY_TIMER
 661  *  wValue:          0
 662  *  wIndex:          Port
 663  *  wLength:         0
 664  *  Data:            latency (on return)
 665  */
 666
 667 /*
 668  * FTDI_SIO_SET_LATENCY_TIMER
 669  *
 670  * Set the timeout interval. The FTDI collects data from the slave
 671  * device, transmitting it to the host when either A) 62 bytes are
 672  * received, or B) the timeout interval has elapsed and the buffer
 673  * contains at least 1 byte.  Setting this value to a small number
 674  * can dramatically improve performance for applications which send
 675  * small packets, since the default value is 16ms.
 676  */
 677 #define  FTDI_SIO_SET_LATENCY_TIMER_REQUEST FTDI_SIO_SET_LATENCY_TIMER
 678 #define  FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE 0x40
 679
 680 /*
 681  *  BmRequestType:   0100 0000b
 682  *  bRequest:        FTDI_SIO_SET_LATENCY_TIMER
 683  *  wValue:          Latency (milliseconds)
 684  *  wIndex:          Port
 685  *  wLength:         0
 686  *  Data:            None
 687  *
 688  * wValue:
 689  *   B0..7   Latency timer
 690  *   B8..15  0
 691  *
 692  */
 693
 694 /*
 695  * FTDI_SIO_SET_EVENT_CHAR
 696  *
 697  * Set the special event character for the specified communications port.
 698  * If the device sees this character it will immediately return the
 699  * data read so far - rather than wait 40ms or until 62 bytes are read
 700  * which is what normally happens.
 701  */
 702
 703
 704 #define  FTDI_SIO_SET_EVENT_CHAR_REQUEST FTDI_SIO_SET_EVENT_CHAR
 705 #define  FTDI_SIO_SET_EVENT_CHAR_REQUEST_TYPE 0x40
 706
 707
 708 /*
 709  *  BmRequestType:   0100 0000b
 710  *  bRequest:        FTDI_SIO_SET_EVENT_CHAR
 711  *  wValue:          EventChar
 712  *  wIndex:          Port
 713  *  wLength:         0
 714  *  Data:            None
 715  *
 716  * wValue:
 717  *   B0..7   Event Character
 718  *   B8      Event Character Processing
 719  *             0 = disabled
 720  *             1 = enabled
 721  *   B9..15  Reserved
 722  *
 723  */
 724
 725 /* FTDI_SIO_SET_ERROR_CHAR */
 726
 727 /* Set the parity error replacement character for the specified communications port */
 728
 729 /*
 730  *  BmRequestType:  0100 0000b
 731  *  bRequest:       FTDI_SIO_SET_EVENT_CHAR
 732  *  wValue:         Error Char
 733  *  wIndex:         Port
 734  *  wLength:        0
 735  *  Data:           None
 736  *
 737  *Error Char
 738  *  B0..7  Error Character
 739  *  B8     Error Character Processing
 740  *           0 = disabled
 741  *           1 = enabled
 742  *  B9..15 Reserved
 743  *
 744  */
 745
 746 /* FTDI_SIO_GET_MODEM_STATUS */
 747 /* Retrieve the current value of the modem status register */
 748
 749 #define FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE 0xc0
 750 #define FTDI_SIO_GET_MODEM_STATUS_REQUEST FTDI_SIO_GET_MODEM_STATUS
 751 #define FTDI_SIO_CTS_MASK 0x10
 752 #define FTDI_SIO_DSR_MASK 0x20
 753 #define FTDI_SIO_RI_MASK  0x40
 754 #define FTDI_SIO_RLSD_MASK 0x80
 755 /*
 756  *   BmRequestType:   1100 0000b
 757  *   bRequest:        FTDI_SIO_GET_MODEM_STATUS
 758  *   wValue:          zero
 759  *   wIndex:          Port
 760  *   wLength:         1
 761  *   Data:            Status
 762  *
 763  * One byte of data is returned
 764  * B0..3 0
 765  * B4    CTS
 766  *         0 = inactive
 767  *         1 = active
 768  * B5    DSR
 769  *         0 = inactive
 770  *         1 = active
 771  * B6    Ring Indicator (RI)
 772  *         0 = inactive
 773  *         1 = active
 774  * B7    Receive Line Signal Detect (RLSD)
 775  *         0 = inactive
 776  *         1 = active
 777  */
 778
 779
 780
 781 /* Descriptors returned by the device
 782  *
 783  *  Device Descriptor
 784  *
 785  * Offset       Field           Size    Value   Description
 786  * 0    bLength         1       0x12    Size of descriptor in bytes
 787  * 1    bDescriptorType 1       0x01    DEVICE Descriptor Type
 788  * 2    bcdUSB          2       0x0110  USB Spec Release Number
 789  * 4    bDeviceClass    1       0x00    Class Code
 790  * 5    bDeviceSubClass 1       0x00    SubClass Code
 791  * 6    bDeviceProtocol 1       0x00    Protocol Code
 792  * 7    bMaxPacketSize0 1       0x08    Maximum packet size for endpoint 0
 793  * 8    idVendor        2       0x0403  Vendor ID
 794  * 10   idProduct       2       0x8372  Product ID (FTDI_SIO_PID)
 795  * 12   bcdDevice       2       0x0001  Device release number
 796  * 14   iManufacturer   1       0x01    Index of man. string desc
 797  * 15   iProduct        1       0x02    Index of prod string desc
 798  * 16   iSerialNumber   1       0x02    Index of serial nmr string desc
 799  * 17   bNumConfigurations 1    0x01    Number of possible configurations
 800  *
 801  * Configuration Descriptor
 802  *
 803  * Offset       Field                   Size    Value
 804  * 0    bLength                 1       0x09    Size of descriptor in bytes
 805  * 1    bDescriptorType         1       0x02    CONFIGURATION Descriptor Type
 806  * 2    wTotalLength            2       0x0020  Total length of data
 807  * 4    bNumInterfaces          1       0x01    Number of interfaces supported
 808  * 5    bConfigurationValue     1       0x01    Argument for SetCOnfiguration() req
 809  * 6    iConfiguration          1       0x02    Index of config string descriptor
 810  * 7    bmAttributes            1       0x20    Config characteristics Remote Wakeup
 811  * 8    MaxPower                1       0x1E    Max power consumption
 812  *
 813  * Interface Descriptor
 814  *
 815  * Offset       Field                   Size    Value
 816  * 0    bLength                 1       0x09    Size of descriptor in bytes
 817  * 1    bDescriptorType         1       0x04    INTERFACE Descriptor Type
 818  * 2    bInterfaceNumber        1       0x00    Number of interface
 819  * 3    bAlternateSetting       1       0x00    Value used to select alternate
 820  * 4    bNumEndpoints           1       0x02    Number of endpoints
 821  * 5    bInterfaceClass         1       0xFF    Class Code
 822  * 6    bInterfaceSubClass      1       0xFF    Subclass Code
 823  * 7    bInterfaceProtocol      1       0xFF    Protocol Code
 824  * 8    iInterface              1       0x02    Index of interface string description
 825  *
 826  * IN Endpoint Descriptor
 827  *
 828  * Offset       Field                   Size    Value
 829  * 0    bLength                 1       0x07    Size of descriptor in bytes
 830  * 1    bDescriptorType         1       0x05    ENDPOINT descriptor type
 831  * 2    bEndpointAddress        1       0x82    Address of endpoint
 832  * 3    bmAttributes            1       0x02    Endpoint attributes - Bulk
 833  * 4    bNumEndpoints           2       0x0040  maximum packet size
 834  * 5    bInterval               1       0x00    Interval for polling endpoint
 835  *
 836  * OUT Endpoint Descriptor
 837  *
 838  * Offset       Field                   Size    Value
 839  * 0    bLength                 1       0x07    Size of descriptor in bytes
 840  * 1    bDescriptorType         1       0x05    ENDPOINT descriptor type
 841  * 2    bEndpointAddress        1       0x02    Address of endpoint
 842  * 3    bmAttributes            1       0x02    Endpoint attributes - Bulk
 843  * 4    bNumEndpoints           2       0x0040  maximum packet size
 844  * 5    bInterval               1       0x00    Interval for polling endpoint
 845  *
 846  * DATA FORMAT
 847  *
 848  * IN Endpoint
 849  *
 850  * The device reserves the first two bytes of data on this endpoint to contain the current
 851  * values of the modem and line status registers. In the absence of data, the device
 852  * generates a message consisting of these two status bytes every 40 ms
 853  *
 854  * Byte 0: Modem Status
 855  *
 856  * Offset       Description
 857  * B0   Reserved - must be 1
 858  * B1   Reserved - must be 0
 859  * B2   Reserved - must be 0
 860  * B3   Reserved - must be 0
 861  * B4   Clear to Send (CTS)
 862  * B5   Data Set Ready (DSR)
 863  * B6   Ring Indicator (RI)
 864  * B7   Receive Line Signal Detect (RLSD)
 865  *
 866  * Byte 1: Line Status
 867  *
 868  * Offset       Description
 869  * B0   Data Ready (DR)
 870  * B1   Overrun Error (OE)
 871  * B2   Parity Error (PE)
 872  * B3   Framing Error (FE)
 873  * B4   Break Interrupt (BI)
 874  * B5   Transmitter Holding Register (THRE)
 875  * B6   Transmitter Empty (TEMT)
 876  * B7   Error in RCVR FIFO
 877  *
 878  */
 879 #define FTDI_RS0_CTS    (1 << 4)
 880 #define FTDI_RS0_DSR    (1 << 5)
 881 #define FTDI_RS0_RI     (1 << 6)
 882 #define FTDI_RS0_RLSD   (1 << 7)
 883
 884 #define FTDI_RS_DR  1
 885 #define FTDI_RS_OE (1<<1)
 886 #define FTDI_RS_PE (1<<2)
 887 #define FTDI_RS_FE (1<<3)
 888 #define FTDI_RS_BI (1<<4)
 889 #define FTDI_RS_THRE (1<<5)
 890 #define FTDI_RS_TEMT (1<<6)
 891 #define FTDI_RS_FIFO  (1<<7)
 892
 893 /*
 894  * OUT Endpoint
 895  *
 896  * This device reserves the first bytes of data on this endpoint contain the length
 897  * and port identifier of the message. For the FTDI USB Serial converter the port
 898  * identifier is always 1.
 899  *
 900  * Byte 0: Line Status
 901  *
 902  * Offset       Description
 903  * B0   Reserved - must be 1
 904  * B1   Reserved - must be 0
 905  * B2..7        Length of message - (not including Byte 0)
 906  *
 907  */
 908