drivers/ide/serverworks.c

   1 /*
   2  * Copyright (C) 1998-2000 Michel Aubry
   3  * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
   4  * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
   5  * Copyright (C)      2007 Bartlomiej Zolnierkiewicz
   6  * Portions copyright (c) 2001 Sun Microsystems
   7  *
   8  *
   9  * RCC/ServerWorks IDE driver for Linux
  10  *
  11  *   OSB4: `Open South Bridge' IDE Interface (fn 1)
  12  *         supports UDMA mode 2 (33 MB/s)
  13  *
  14  *   CSB5: `Champion South Bridge' IDE Interface (fn 1)
  15  *         all revisions support UDMA mode 4 (66 MB/s)
  16  *         revision A2.0 and up support UDMA mode 5 (100 MB/s)
  17  *
  18  *         *** The CSB5 does not provide ANY register ***
  19  *         *** to detect 80-conductor cable presence. ***
  20  *
  21  *   CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
  22  *
  23  *   HT1000: AKA BCM5785 - Hypertransport Southbridge for Opteron systems. IDE
  24  *   controller same as the CSB6. Single channel ATA100 only.
  25  *
  26  * Documentation:
  27  *      Available under NDA only. Errata info very hard to get.
  28  *
  29  */
  30
  31 #include <linux/types.h>
  32 #include <linux/module.h>
  33 #include <linux/kernel.h>
  34 #include <linux/pci.h>
  35 #include <linux/ide.h>
  36 #include <linux/init.h>
  37
  38 #include <asm/io.h>
  39
  40 #define DRV_NAME "serverworks"
  41
  42 #define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
  43 #define SVWKS_CSB6_REVISION     0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
  44
  45 /* Seagate Barracuda ATA IV Family drives in UDMA mode 5
  46  * can overrun their FIFOs when used with the CSB5 */
  47 static const char *svwks_bad_ata100[] = {
  48         "ST320011A",
  49         "ST340016A",
  50         "ST360021A",
  51         "ST380021A",
  52         NULL
  53 };
  54
  55 static struct pci_dev *isa_dev;
  56
  57 static int check_in_drive_lists (ide_drive_t *drive, const char **list)
  58 {
  59         char *m = (char *)&drive->id[ATA_ID_PROD];
  60
  61         while (*list)
  62                 if (!strcmp(*list++, m))
  63                         return 1;
  64         return 0;
  65 }
  66
  67 static u8 svwks_udma_filter(ide_drive_t *drive)
  68 {
  69         struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
  70         u8 mask = 0;
  71
  72         if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
  73                 return 0x1f;
  74         if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
  75                 u32 reg = 0;
  76                 if (isa_dev)
  77                         pci_read_config_dword(isa_dev, 0x64, &reg);
  78
  79                 /*
  80                  *      Don't enable UDMA on disk devices for the moment
  81                  */
  82                 if(drive->media == ide_disk)
  83                         return 0;
  84                 /* Check the OSB4 DMA33 enable bit */
  85                 return ((reg & 0x00004000) == 0x00004000) ? 0x07 : 0;
  86         } else if (dev->revision < SVWKS_CSB5_REVISION_NEW) {
  87                 return 0x07;
  88         } else if (dev->revision >= SVWKS_CSB5_REVISION_NEW) {
  89                 u8 btr = 0, mode;
  90                 pci_read_config_byte(dev, 0x5A, &btr);
  91                 mode = btr & 0x3;
  92
  93                 /* If someone decides to do UDMA133 on CSB5 the same
  94                    issue will bite so be inclusive */
  95                 if (mode > 2 && check_in_drive_lists(drive, svwks_bad_ata100))
  96                         mode = 2;
  97
  98                 switch(mode) {
  99                 case 3:  mask = 0x3f; break;
 100                 case 2:  mask = 0x1f; break;
 101                 case 1:  mask = 0x07; break;
 102                 default: mask = 0x00; break;
 103                 }
 104         }
 105         if (((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
 106              (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) &&
 107             (!(PCI_FUNC(dev->devfn) & 1)))
 108                 mask = 0x1f;
 109
 110         return mask;
 111 }
 112
 113 static u8 svwks_csb_check (struct pci_dev *dev)
 114 {
 115         switch (dev->device) {
 116                 case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
 117                 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
 118                 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
 119                 case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
 120                         return 1;
 121                 default:
 122                         break;
 123         }
 124         return 0;
 125 }
 126
 127 static void svwks_set_pio_mode(ide_drive_t *drive, const u8 pio)
 128 {
 129         static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
 130         static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };
 131
 132         struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
 133
 134         pci_write_config_byte(dev, drive_pci[drive->dn], pio_modes[pio]);
 135
 136         if (svwks_csb_check(dev)) {
 137                 u16 csb_pio = 0;
 138
 139                 pci_read_config_word(dev, 0x4a, &csb_pio);
 140
 141                 csb_pio &= ~(0x0f << (4 * drive->dn));
 142                 csb_pio |= (pio << (4 * drive->dn));
 143
 144                 pci_write_config_word(dev, 0x4a, csb_pio);
 145         }
 146 }
 147
 148 static void svwks_set_dma_mode(ide_drive_t *drive, const u8 speed)
 149 {
 150         static const u8 udma_modes[]            = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
 151         static const u8 dma_modes[]             = { 0x77, 0x21, 0x20 };
 152         static const u8 drive_pci2[]            = { 0x45, 0x44, 0x47, 0x46 };
 153
 154         ide_hwif_t *hwif        = drive->hwif;
 155         struct pci_dev *dev     = to_pci_dev(hwif->dev);
 156         u8 unit                 = drive->dn & 1;
 157
 158         u8 ultra_enable  = 0, ultra_timing = 0, dma_timing = 0;
 159
 160         pci_read_config_byte(dev, (0x56|hwif->channel), &ultra_timing);
 161         pci_read_config_byte(dev, 0x54, &ultra_enable);
 162
 163         ultra_timing    &= ~(0x0F << (4*unit));
 164         ultra_enable    &= ~(0x01 << drive->dn);
 165
 166         if (speed >= XFER_UDMA_0) {
 167                 dma_timing   |= dma_modes[2];
 168                 ultra_timing |= (udma_modes[speed - XFER_UDMA_0] << (4 * unit));
 169                 ultra_enable |= (0x01 << drive->dn);
 170         } else if (speed >= XFER_MW_DMA_0)
 171                 dma_timing   |= dma_modes[speed - XFER_MW_DMA_0];
 172
 173         pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
 174         pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
 175         pci_write_config_byte(dev, 0x54, ultra_enable);
 176 }
 177
 178 static unsigned int init_chipset_svwks(struct pci_dev *dev)
 179 {
 180         unsigned int reg;
 181         u8 btr;
 182
 183         /* force Master Latency Timer value to 64 PCICLKs */
 184         pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x40);
 185
 186         /* OSB4 : South Bridge and IDE */
 187         if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
 188                 isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
 189                           PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
 190                 if (isa_dev) {
 191                         pci_read_config_dword(isa_dev, 0x64, &reg);
 192                         reg &= ~0x00002000; /* disable 600ns interrupt mask */
 193                         if(!(reg & 0x00004000))
 194                                 printk(KERN_DEBUG DRV_NAME " %s: UDMA not BIOS "
 195                                         "enabled.\n", pci_name(dev));
 196                         reg |=  0x00004000; /* enable UDMA/33 support */
 197                         pci_write_config_dword(isa_dev, 0x64, reg);
 198                 }
 199         }
 200
 201         /* setup CSB5/CSB6 : South Bridge and IDE option RAID */
 202         else if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
 203                  (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
 204                  (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
 205
 206                 /* Third Channel Test */
 207                 if (!(PCI_FUNC(dev->devfn) & 1)) {
 208                         struct pci_dev * findev = NULL;
 209                         u32 reg4c = 0;
 210                         findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
 211                                 PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
 212                         if (findev) {
 213                                 pci_read_config_dword(findev, 0x4C, &reg4c);
 214                                 reg4c &= ~0x000007FF;
 215                                 reg4c |=  0x00000040;
 216                                 reg4c |=  0x00000020;
 217                                 pci_write_config_dword(findev, 0x4C, reg4c);
 218                                 pci_dev_put(findev);
 219                         }
 220                         outb_p(0x06, 0x0c00);
 221                         dev->irq = inb_p(0x0c01);
 222                 } else {
 223                         struct pci_dev * findev = NULL;
 224                         u8 reg41 = 0;
 225
 226                         findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
 227                                         PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
 228                         if (findev) {
 229                                 pci_read_config_byte(findev, 0x41, &reg41);
 230                                 reg41 &= ~0x40;
 231                                 pci_write_config_byte(findev, 0x41, reg41);
 232                                 pci_dev_put(findev);
 233                         }
 234                         /*
 235                          * This is a device pin issue on CSB6.
 236                          * Since there will be a future raid mode,
 237                          * early versions of the chipset require the
 238                          * interrupt pin to be set, and it is a compatibility
 239                          * mode issue.
 240                          */
 241                         if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
 242                                 dev->irq = 0;
 243                 }
 244 //              pci_read_config_dword(dev, 0x40, &pioreg)
 245 //              pci_write_config_dword(dev, 0x40, 0x99999999);
 246 //              pci_read_config_dword(dev, 0x44, &dmareg);
 247 //              pci_write_config_dword(dev, 0x44, 0xFFFFFFFF);
 248                 /* setup the UDMA Control register
 249                  *
 250                  * 1. clear bit 6 to enable DMA
 251                  * 2. enable DMA modes with bits 0-1
 252                  *      00 : legacy
 253                  *      01 : udma2
 254                  *      10 : udma2/udma4
 255                  *      11 : udma2/udma4/udma5
 256                  */
 257                 pci_read_config_byte(dev, 0x5A, &btr);
 258                 btr &= ~0x40;
 259                 if (!(PCI_FUNC(dev->devfn) & 1))
 260                         btr |= 0x2;
 261                 else
 262                         btr |= (dev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
 263                 pci_write_config_byte(dev, 0x5A, btr);
 264         }
 265         /* Setup HT1000 SouthBridge Controller - Single Channel Only */
 266         else if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
 267                 pci_read_config_byte(dev, 0x5A, &btr);
 268                 btr &= ~0x40;
 269                 btr |= 0x3;
 270                 pci_write_config_byte(dev, 0x5A, btr);
 271         }
 272
 273         return dev->irq;
 274 }
 275
 276 static u8 ata66_svwks_svwks(ide_hwif_t *hwif)
 277 {
 278         return ATA_CBL_PATA80;
 279 }
 280
 281 /* On Dell PowerEdge servers with a CSB5/CSB6, the top two bits
 282  * of the subsystem device ID indicate presence of an 80-pin cable.
 283  * Bit 15 clear = secondary IDE channel does not have 80-pin cable.
 284  * Bit 15 set   = secondary IDE channel has 80-pin cable.
 285  * Bit 14 clear = primary IDE channel does not have 80-pin cable.
 286  * Bit 14 set   = primary IDE channel has 80-pin cable.
 287  */
 288 static u8 ata66_svwks_dell(ide_hwif_t *hwif)
 289 {
 290         struct pci_dev *dev = to_pci_dev(hwif->dev);
 291
 292         if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
 293             dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
 294             (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE ||
 295              dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE))
 296                 return ((1 << (hwif->channel + 14)) &
 297                         dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
 298         return ATA_CBL_PATA40;
 299 }
 300
 301 /* Sun Cobalt Alpine hardware avoids the 80-pin cable
 302  * detect issue by attaching the drives directly to the board.
 303  * This check follows the Dell precedent (how scary is that?!)
 304  *
 305  * WARNING: this only works on Alpine hardware!
 306  */
 307 static u8 ata66_svwks_cobalt(ide_hwif_t *hwif)
 308 {
 309         struct pci_dev *dev = to_pci_dev(hwif->dev);
 310
 311         if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN &&
 312             dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
 313             dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
 314                 return ((1 << (hwif->channel + 14)) &
 315                         dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
 316         return ATA_CBL_PATA40;
 317 }
 318
 319 static u8 svwks_cable_detect(ide_hwif_t *hwif)
 320 {
 321         struct pci_dev *dev = to_pci_dev(hwif->dev);
 322
 323         /* Server Works */
 324         if (dev->subsystem_vendor == PCI_VENDOR_ID_SERVERWORKS)
 325                 return ata66_svwks_svwks (hwif);
 326
 327         /* Dell PowerEdge */
 328         if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL)
 329                 return ata66_svwks_dell (hwif);
 330
 331         /* Cobalt Alpine */
 332         if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN)
 333                 return ata66_svwks_cobalt (hwif);
 334
 335         /* Per Specified Design by OEM, and ASIC Architect */
 336         if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
 337             (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2))
 338                 return ATA_CBL_PATA80;
 339
 340         return ATA_CBL_PATA40;
 341 }
 342
 343 static const struct ide_port_ops osb4_port_ops = {
 344         .set_pio_mode           = svwks_set_pio_mode,
 345         .set_dma_mode           = svwks_set_dma_mode,
 346         .udma_filter            = svwks_udma_filter,
 347 };
 348
 349 static const struct ide_port_ops svwks_port_ops = {
 350         .set_pio_mode           = svwks_set_pio_mode,
 351         .set_dma_mode           = svwks_set_dma_mode,
 352         .udma_filter            = svwks_udma_filter,
 353         .cable_detect           = svwks_cable_detect,
 354 };
 355
 356 #define IDE_HFLAGS_SVWKS IDE_HFLAG_LEGACY_IRQS
 357
 358 static const struct ide_port_info serverworks_chipsets[] __devinitdata = {
 359         {       /* 0: OSB4 */
 360                 .name           = DRV_NAME,
 361                 .init_chipset   = init_chipset_svwks,
 362                 .port_ops       = &osb4_port_ops,
 363                 .host_flags     = IDE_HFLAGS_SVWKS,
 364                 .pio_mask       = ATA_PIO4,
 365                 .mwdma_mask     = ATA_MWDMA2,
 366                 .udma_mask      = 0x00, /* UDMA is problematic on OSB4 */
 367         },
 368         {       /* 1: CSB5 */
 369                 .name           = DRV_NAME,
 370                 .init_chipset   = init_chipset_svwks,
 371                 .port_ops       = &svwks_port_ops,
 372                 .host_flags     = IDE_HFLAGS_SVWKS,
 373                 .pio_mask       = ATA_PIO4,
 374                 .mwdma_mask     = ATA_MWDMA2,
 375                 .udma_mask      = ATA_UDMA5,
 376         },
 377         {       /* 2: CSB6 */
 378                 .name           = DRV_NAME,
 379                 .init_chipset   = init_chipset_svwks,
 380                 .port_ops       = &svwks_port_ops,
 381                 .host_flags     = IDE_HFLAGS_SVWKS,
 382                 .pio_mask       = ATA_PIO4,
 383                 .mwdma_mask     = ATA_MWDMA2,
 384                 .udma_mask      = ATA_UDMA5,
 385         },
 386         {       /* 3: CSB6-2 */
 387                 .name           = DRV_NAME,
 388                 .init_chipset   = init_chipset_svwks,
 389                 .port_ops       = &svwks_port_ops,
 390                 .host_flags     = IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
 391                 .pio_mask       = ATA_PIO4,
 392                 .mwdma_mask     = ATA_MWDMA2,
 393                 .udma_mask      = ATA_UDMA5,
 394         },
 395         {       /* 4: HT1000 */
 396                 .name           = DRV_NAME,
 397                 .init_chipset   = init_chipset_svwks,
 398                 .port_ops       = &svwks_port_ops,
 399                 .host_flags     = IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
 400                 .pio_mask       = ATA_PIO4,
 401                 .mwdma_mask     = ATA_MWDMA2,
 402                 .udma_mask      = ATA_UDMA5,
 403         }
 404 };
 405
 406 /**
 407  *      svwks_init_one  -       called when a OSB/CSB is found
 408  *      @dev: the svwks device
 409  *      @id: the matching pci id
 410  *
 411  *      Called when the PCI registration layer (or the IDE initialization)
 412  *      finds a device matching our IDE device tables.
 413  */
 414
 415 static int __devinit svwks_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 416 {
 417         struct ide_port_info d;
 418         u8 idx = id->driver_data;
 419
 420         d = serverworks_chipsets[idx];
 421
 422         if (idx == 1)
 423                 d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
 424         else if (idx == 2 || idx == 3) {
 425                 if ((PCI_FUNC(dev->devfn) & 1) == 0) {
 426                         if (pci_resource_start(dev, 0) != 0x01f1)
 427                                 d.host_flags |= IDE_HFLAG_NON_BOOTABLE;
 428                         d.host_flags |= IDE_HFLAG_SINGLE;
 429                 } else
 430                         d.host_flags &= ~IDE_HFLAG_SINGLE;
 431         }
 432
 433         return ide_pci_init_one(dev, &d, NULL);
 434 }
 435
 436 static const struct pci_device_id svwks_pci_tbl[] = {
 437         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE),   0 },
 438         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE),   1 },
 439         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE),   2 },
 440         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2),  3 },
 441         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 4 },
 442         { 0, },
 443 };
 444 MODULE_DEVICE_TABLE(pci, svwks_pci_tbl);
 445
 446 static struct pci_driver svwks_pci_driver = {
 447         .name           = "Serverworks_IDE",
 448         .id_table       = svwks_pci_tbl,
 449         .probe          = svwks_init_one,
 450         .remove         = ide_pci_remove,
 451         .suspend        = ide_pci_suspend,
 452         .resume         = ide_pci_resume,
 453 };
 454
 455 static int __init svwks_ide_init(void)
 456 {
 457         return ide_pci_register_driver(&svwks_pci_driver);
 458 }
 459
 460 static void __exit svwks_ide_exit(void)
 461 {
 462         pci_unregister_driver(&svwks_pci_driver);
 463 }
 464
 465 module_init(svwks_ide_init);
 466 module_exit(svwks_ide_exit);
 467
 468 MODULE_AUTHOR("Michael Aubry. Andrzej Krzysztofowicz, Andre Hedrick");
 469 MODULE_DESCRIPTION("PCI driver module for Serverworks OSB4/CSB5/CSB6 IDE");
 470 MODULE_LICENSE("GPL");