Merge branch 'next' of git://git.monstr.eu/linux-2.6-microblaze
[linux-2.6/linux-acpi-2.6/ibm-acpi-2.6.git] / drivers / scsi / g_NCR5380.c
blob81182badfeb10f62c5e499c8d587198ac37fa696
1 /*
2 * Generic Generic NCR5380 driver
3 *
4 * Copyright 1993, Drew Eckhardt
5 * Visionary Computing
6 * (Unix and Linux consulting and custom programming)
7 * drew@colorado.edu
8 * +1 (303) 440-4894
10 * NCR53C400 extensions (c) 1994,1995,1996, Kevin Lentin
11 * K.Lentin@cs.monash.edu.au
13 * NCR53C400A extensions (c) 1996, Ingmar Baumgart
14 * ingmar@gonzo.schwaben.de
16 * DTC3181E extensions (c) 1997, Ronald van Cuijlenborg
17 * ronald.van.cuijlenborg@tip.nl or nutty@dds.nl
19 * Added ISAPNP support for DTC436 adapters,
20 * Thomas Sailer, sailer@ife.ee.ethz.ch
22 * ALPHA RELEASE 1.
24 * For more information, please consult
26 * NCR 5380 Family
27 * SCSI Protocol Controller
28 * Databook
30 * NCR Microelectronics
31 * 1635 Aeroplaza Drive
32 * Colorado Springs, CO 80916
33 * 1+ (719) 578-3400
34 * 1+ (800) 334-5454
37 /*
38 * TODO : flesh out DMA support, find some one actually using this (I have
39 * a memory mapped Trantor board that works fine)
43 * Options :
45 * PARITY - enable parity checking. Not supported.
47 * SCSI2 - enable support for SCSI-II tagged queueing. Untested.
49 * USLEEP - enable support for devices that don't disconnect. Untested.
51 * The card is detected and initialized in one of several ways :
52 * 1. With command line overrides - NCR5380=port,irq may be
53 * used on the LILO command line to override the defaults.
55 * 2. With the GENERIC_NCR5380_OVERRIDE compile time define. This is
56 * specified as an array of address, irq, dma, board tuples. Ie, for
57 * one board at 0x350, IRQ5, no dma, I could say
58 * -DGENERIC_NCR5380_OVERRIDE={{0xcc000, 5, DMA_NONE, BOARD_NCR5380}}
60 * -1 should be specified for no or DMA interrupt, -2 to autoprobe for an
61 * IRQ line if overridden on the command line.
63 * 3. When included as a module, with arguments passed on the command line:
64 * ncr_irq=xx the interrupt
65 * ncr_addr=xx the port or base address (for port or memory
66 * mapped, resp.)
67 * ncr_dma=xx the DMA
68 * ncr_5380=1 to set up for a NCR5380 board
69 * ncr_53c400=1 to set up for a NCR53C400 board
70 * e.g.
71 * modprobe g_NCR5380 ncr_irq=5 ncr_addr=0x350 ncr_5380=1
72 * for a port mapped NCR5380 board or
73 * modprobe g_NCR5380 ncr_irq=255 ncr_addr=0xc8000 ncr_53c400=1
74 * for a memory mapped NCR53C400 board with interrupts disabled.
76 * 255 should be specified for no or DMA interrupt, 254 to autoprobe for an
77 * IRQ line if overridden on the command line.
82 * $Log: generic_NCR5380.c,v $
85 /* settings for DTC3181E card with only Mustek scanner attached */
86 #define USLEEP
87 #define USLEEP_POLL 1
88 #define USLEEP_SLEEP 20
89 #define USLEEP_WAITLONG 500
91 #define AUTOPROBE_IRQ
92 #define AUTOSENSE
95 #ifdef CONFIG_SCSI_GENERIC_NCR53C400
96 #define NCR53C400_PSEUDO_DMA 1
97 #define PSEUDO_DMA
98 #define NCR53C400
99 #define NCR5380_STATS
100 #undef NCR5380_STAT_LIMIT
101 #endif
103 #include <asm/system.h>
104 #include <asm/io.h>
105 #include <linux/signal.h>
106 #include <linux/blkdev.h>
107 #include "scsi.h"
108 #include <scsi/scsi_host.h>
109 #include "g_NCR5380.h"
110 #include "NCR5380.h"
111 #include <linux/stat.h>
112 #include <linux/init.h>
113 #include <linux/ioport.h>
114 #include <linux/isapnp.h>
115 #include <linux/delay.h>
116 #include <linux/interrupt.h>
118 #define NCR_NOT_SET 0
119 static int ncr_irq = NCR_NOT_SET;
120 static int ncr_dma = NCR_NOT_SET;
121 static int ncr_addr = NCR_NOT_SET;
122 static int ncr_5380 = NCR_NOT_SET;
123 static int ncr_53c400 = NCR_NOT_SET;
124 static int ncr_53c400a = NCR_NOT_SET;
125 static int dtc_3181e = NCR_NOT_SET;
127 static struct override {
128 NCR5380_map_type NCR5380_map_name;
129 int irq;
130 int dma;
131 int board; /* Use NCR53c400, Ricoh, etc. extensions ? */
132 } overrides
133 #ifdef GENERIC_NCR5380_OVERRIDE
134 [] __initdata = GENERIC_NCR5380_OVERRIDE;
135 #else
136 [1] __initdata = { { 0,},};
137 #endif
139 #define NO_OVERRIDES ARRAY_SIZE(overrides)
141 #ifndef MODULE
144 * internal_setup - handle lilo command string override
145 * @board: BOARD_* identifier for the board
146 * @str: unused
147 * @ints: numeric parameters
149 * Do LILO command line initialization of the overrides array. Display
150 * errors when needed
152 * Locks: none
155 static void __init internal_setup(int board, char *str, int *ints)
157 static int commandline_current = 0;
158 switch (board) {
159 case BOARD_NCR5380:
160 if (ints[0] != 2 && ints[0] != 3) {
161 printk(KERN_ERR "generic_NCR5380_setup : usage ncr5380=" STRVAL(NCR5380_map_name) ",irq,dma\n");
162 return;
164 break;
165 case BOARD_NCR53C400:
166 if (ints[0] != 2) {
167 printk(KERN_ERR "generic_NCR53C400_setup : usage ncr53c400=" STRVAL(NCR5380_map_name) ",irq\n");
168 return;
170 break;
171 case BOARD_NCR53C400A:
172 if (ints[0] != 2) {
173 printk(KERN_ERR "generic_NCR53C400A_setup : usage ncr53c400a=" STRVAL(NCR5380_map_name) ",irq\n");
174 return;
176 break;
177 case BOARD_DTC3181E:
178 if (ints[0] != 2) {
179 printk("generic_DTC3181E_setup : usage dtc3181e=" STRVAL(NCR5380_map_name) ",irq\n");
180 return;
182 break;
185 if (commandline_current < NO_OVERRIDES) {
186 overrides[commandline_current].NCR5380_map_name = (NCR5380_map_type) ints[1];
187 overrides[commandline_current].irq = ints[2];
188 if (ints[0] == 3)
189 overrides[commandline_current].dma = ints[3];
190 else
191 overrides[commandline_current].dma = DMA_NONE;
192 overrides[commandline_current].board = board;
193 ++commandline_current;
199 * do_NCR53C80_setup - set up entry point
200 * @str: unused
202 * Setup function invoked at boot to parse the ncr5380= command
203 * line.
206 static int __init do_NCR5380_setup(char *str)
208 int ints[10];
210 get_options(str, ARRAY_SIZE(ints), ints);
211 internal_setup(BOARD_NCR5380, str, ints);
212 return 1;
216 * do_NCR53C400_setup - set up entry point
217 * @str: unused
218 * @ints: integer parameters from kernel setup code
220 * Setup function invoked at boot to parse the ncr53c400= command
221 * line.
224 static int __init do_NCR53C400_setup(char *str)
226 int ints[10];
228 get_options(str, ARRAY_SIZE(ints), ints);
229 internal_setup(BOARD_NCR53C400, str, ints);
230 return 1;
234 * do_NCR53C400A_setup - set up entry point
235 * @str: unused
236 * @ints: integer parameters from kernel setup code
238 * Setup function invoked at boot to parse the ncr53c400a= command
239 * line.
242 static int __init do_NCR53C400A_setup(char *str)
244 int ints[10];
246 get_options(str, ARRAY_SIZE(ints), ints);
247 internal_setup(BOARD_NCR53C400A, str, ints);
248 return 1;
252 * do_DTC3181E_setup - set up entry point
253 * @str: unused
254 * @ints: integer parameters from kernel setup code
256 * Setup function invoked at boot to parse the dtc3181e= command
257 * line.
260 static int __init do_DTC3181E_setup(char *str)
262 int ints[10];
264 get_options(str, ARRAY_SIZE(ints), ints);
265 internal_setup(BOARD_DTC3181E, str, ints);
266 return 1;
269 #endif
272 * generic_NCR5380_detect - look for NCR5380 controllers
273 * @tpnt: the scsi template
275 * Scan for the present of NCR5380, NCR53C400, NCR53C400A, DTC3181E
276 * and DTC436(ISAPnP) controllers. If overrides have been set we use
277 * them.
279 * The caller supplied NCR5380_init function is invoked from here, before
280 * the interrupt line is taken.
282 * Locks: none
285 int __init generic_NCR5380_detect(struct scsi_host_template * tpnt)
287 static int current_override = 0;
288 int count;
289 unsigned int *ports;
290 #ifndef SCSI_G_NCR5380_MEM
291 int i;
292 unsigned long region_size = 16;
293 #endif
294 static unsigned int __initdata ncr_53c400a_ports[] = {
295 0x280, 0x290, 0x300, 0x310, 0x330, 0x340, 0x348, 0x350, 0
297 static unsigned int __initdata dtc_3181e_ports[] = {
298 0x220, 0x240, 0x280, 0x2a0, 0x2c0, 0x300, 0x320, 0x340, 0
300 int flags = 0;
301 struct Scsi_Host *instance;
302 #ifdef SCSI_G_NCR5380_MEM
303 unsigned long base;
304 void __iomem *iomem;
305 #endif
307 if (ncr_irq != NCR_NOT_SET)
308 overrides[0].irq = ncr_irq;
309 if (ncr_dma != NCR_NOT_SET)
310 overrides[0].dma = ncr_dma;
311 if (ncr_addr != NCR_NOT_SET)
312 overrides[0].NCR5380_map_name = (NCR5380_map_type) ncr_addr;
313 if (ncr_5380 != NCR_NOT_SET)
314 overrides[0].board = BOARD_NCR5380;
315 else if (ncr_53c400 != NCR_NOT_SET)
316 overrides[0].board = BOARD_NCR53C400;
317 else if (ncr_53c400a != NCR_NOT_SET)
318 overrides[0].board = BOARD_NCR53C400A;
319 else if (dtc_3181e != NCR_NOT_SET)
320 overrides[0].board = BOARD_DTC3181E;
321 #ifndef SCSI_G_NCR5380_MEM
322 if (!current_override && isapnp_present()) {
323 struct pnp_dev *dev = NULL;
324 count = 0;
325 while ((dev = pnp_find_dev(NULL, ISAPNP_VENDOR('D', 'T', 'C'), ISAPNP_FUNCTION(0x436e), dev))) {
326 if (count >= NO_OVERRIDES)
327 break;
328 if (pnp_device_attach(dev) < 0)
329 continue;
330 if (pnp_activate_dev(dev) < 0) {
331 printk(KERN_ERR "dtc436e probe: activate failed\n");
332 pnp_device_detach(dev);
333 continue;
335 if (!pnp_port_valid(dev, 0)) {
336 printk(KERN_ERR "dtc436e probe: no valid port\n");
337 pnp_device_detach(dev);
338 continue;
340 if (pnp_irq_valid(dev, 0))
341 overrides[count].irq = pnp_irq(dev, 0);
342 else
343 overrides[count].irq = SCSI_IRQ_NONE;
344 if (pnp_dma_valid(dev, 0))
345 overrides[count].dma = pnp_dma(dev, 0);
346 else
347 overrides[count].dma = DMA_NONE;
348 overrides[count].NCR5380_map_name = (NCR5380_map_type) pnp_port_start(dev, 0);
349 overrides[count].board = BOARD_DTC3181E;
350 count++;
353 #endif
354 tpnt->proc_name = "g_NCR5380";
356 for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
357 if (!(overrides[current_override].NCR5380_map_name))
358 continue;
360 ports = NULL;
361 switch (overrides[current_override].board) {
362 case BOARD_NCR5380:
363 flags = FLAG_NO_PSEUDO_DMA;
364 break;
365 case BOARD_NCR53C400:
366 flags = FLAG_NCR53C400;
367 break;
368 case BOARD_NCR53C400A:
369 flags = FLAG_NO_PSEUDO_DMA;
370 ports = ncr_53c400a_ports;
371 break;
372 case BOARD_DTC3181E:
373 flags = FLAG_NO_PSEUDO_DMA | FLAG_DTC3181E;
374 ports = dtc_3181e_ports;
375 break;
378 #ifndef SCSI_G_NCR5380_MEM
379 if (ports) {
380 /* wakeup sequence for the NCR53C400A and DTC3181E */
382 /* Disable the adapter and look for a free io port */
383 outb(0x59, 0x779);
384 outb(0xb9, 0x379);
385 outb(0xc5, 0x379);
386 outb(0xae, 0x379);
387 outb(0xa6, 0x379);
388 outb(0x00, 0x379);
390 if (overrides[current_override].NCR5380_map_name != PORT_AUTO)
391 for (i = 0; ports[i]; i++) {
392 if (!request_region(ports[i], 16, "ncr53c80"))
393 continue;
394 if (overrides[current_override].NCR5380_map_name == ports[i])
395 break;
396 release_region(ports[i], 16);
397 } else
398 for (i = 0; ports[i]; i++) {
399 if (!request_region(ports[i], 16, "ncr53c80"))
400 continue;
401 if (inb(ports[i]) == 0xff)
402 break;
403 release_region(ports[i], 16);
405 if (ports[i]) {
406 /* At this point we have our region reserved */
407 outb(0x59, 0x779);
408 outb(0xb9, 0x379);
409 outb(0xc5, 0x379);
410 outb(0xae, 0x379);
411 outb(0xa6, 0x379);
412 outb(0x80 | i, 0x379); /* set io port to be used */
413 outb(0xc0, ports[i] + 9);
414 if (inb(ports[i] + 9) != 0x80)
415 continue;
416 else
417 overrides[current_override].NCR5380_map_name = ports[i];
418 } else
419 continue;
421 else
423 /* Not a 53C400A style setup - just grab */
424 if(!(request_region(overrides[current_override].NCR5380_map_name, NCR5380_region_size, "ncr5380")))
425 continue;
426 region_size = NCR5380_region_size;
428 #else
429 base = overrides[current_override].NCR5380_map_name;
430 if (!request_mem_region(base, NCR5380_region_size, "ncr5380"))
431 continue;
432 iomem = ioremap(base, NCR5380_region_size);
433 if (!iomem) {
434 release_mem_region(base, NCR5380_region_size);
435 continue;
437 #endif
438 instance = scsi_register(tpnt, sizeof(struct NCR5380_hostdata));
439 if (instance == NULL) {
440 #ifndef SCSI_G_NCR5380_MEM
441 release_region(overrides[current_override].NCR5380_map_name, region_size);
442 #else
443 iounmap(iomem);
444 release_mem_region(base, NCR5380_region_size);
445 #endif
446 continue;
449 instance->NCR5380_instance_name = overrides[current_override].NCR5380_map_name;
450 #ifndef SCSI_G_NCR5380_MEM
451 instance->n_io_port = region_size;
452 #else
453 ((struct NCR5380_hostdata *)instance->hostdata)->iomem = iomem;
454 #endif
456 NCR5380_init(instance, flags);
458 if (overrides[current_override].irq != IRQ_AUTO)
459 instance->irq = overrides[current_override].irq;
460 else
461 instance->irq = NCR5380_probe_irq(instance, 0xffff);
463 if (instance->irq != SCSI_IRQ_NONE)
464 if (request_irq(instance->irq, generic_NCR5380_intr,
465 IRQF_DISABLED, "NCR5380", instance)) {
466 printk(KERN_WARNING "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq);
467 instance->irq = SCSI_IRQ_NONE;
470 if (instance->irq == SCSI_IRQ_NONE) {
471 printk(KERN_INFO "scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
472 printk(KERN_INFO "scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
475 printk(KERN_INFO "scsi%d : at " STRVAL(NCR5380_map_name) " 0x%x", instance->host_no, (unsigned int) instance->NCR5380_instance_name);
476 if (instance->irq == SCSI_IRQ_NONE)
477 printk(" interrupts disabled");
478 else
479 printk(" irq %d", instance->irq);
480 printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d", CAN_QUEUE, CMD_PER_LUN, GENERIC_NCR5380_PUBLIC_RELEASE);
481 NCR5380_print_options(instance);
482 printk("\n");
484 ++current_override;
485 ++count;
487 return count;
491 * generic_NCR5380_info - reporting string
492 * @host: NCR5380 to report on
494 * Report driver information for the NCR5380
497 const char *generic_NCR5380_info(struct Scsi_Host *host)
499 static const char string[] = "Generic NCR5380/53C400 Driver";
500 return string;
504 * generic_NCR5380_release_resources - free resources
505 * @instance: host adapter to clean up
507 * Free the generic interface resources from this adapter.
509 * Locks: none
512 int generic_NCR5380_release_resources(struct Scsi_Host *instance)
514 NCR5380_local_declare();
515 NCR5380_setup(instance);
517 if (instance->irq != SCSI_IRQ_NONE)
518 free_irq(instance->irq, instance);
519 NCR5380_exit(instance);
521 #ifndef SCSI_G_NCR5380_MEM
522 release_region(instance->NCR5380_instance_name, instance->n_io_port);
523 #else
524 iounmap(((struct NCR5380_hostdata *)instance->hostdata)->iomem);
525 release_mem_region(instance->NCR5380_instance_name, NCR5380_region_size);
526 #endif
529 return 0;
532 #ifdef BIOSPARAM
534 * generic_NCR5380_biosparam
535 * @disk: disk to compute geometry for
536 * @dev: device identifier for this disk
537 * @ip: sizes to fill in
539 * Generates a BIOS / DOS compatible H-C-S mapping for the specified
540 * device / size.
542 * XXX Most SCSI boards use this mapping, I could be incorrect. Someone
543 * using hard disks on a trantor should verify that this mapping
544 * corresponds to that used by the BIOS / ASPI driver by running the linux
545 * fdisk program and matching the H_C_S coordinates to what DOS uses.
547 * Locks: none
550 static int
551 generic_NCR5380_biosparam(struct scsi_device *sdev, struct block_device *bdev,
552 sector_t capacity, int *ip)
554 ip[0] = 64;
555 ip[1] = 32;
556 ip[2] = capacity >> 11;
557 return 0;
559 #endif
561 #ifdef NCR53C400_PSEUDO_DMA
564 * NCR5380_pread - pseudo DMA read
565 * @instance: adapter to read from
566 * @dst: buffer to read into
567 * @len: buffer length
569 * Perform a pseudo DMA mode read from an NCR53C400 or equivalent
570 * controller
573 static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst, int len)
575 int blocks = len / 128;
576 int start = 0;
577 int bl;
579 NCR5380_local_declare();
580 NCR5380_setup(instance);
582 NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE | CSR_TRANS_DIR);
583 NCR5380_write(C400_BLOCK_COUNTER_REG, blocks);
584 while (1) {
585 if ((bl = NCR5380_read(C400_BLOCK_COUNTER_REG)) == 0) {
586 break;
588 if (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ) {
589 printk(KERN_ERR "53C400r: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks);
590 return -1;
592 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY);
594 #ifndef SCSI_G_NCR5380_MEM
596 int i;
597 for (i = 0; i < 128; i++)
598 dst[start + i] = NCR5380_read(C400_HOST_BUFFER);
600 #else
601 /* implies SCSI_G_NCR5380_MEM */
602 memcpy_fromio(dst + start, iomem + NCR53C400_host_buffer, 128);
603 #endif
604 start += 128;
605 blocks--;
608 if (blocks) {
609 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)
611 // FIXME - no timeout
614 #ifndef SCSI_G_NCR5380_MEM
616 int i;
617 for (i = 0; i < 128; i++)
618 dst[start + i] = NCR5380_read(C400_HOST_BUFFER);
620 #else
621 /* implies SCSI_G_NCR5380_MEM */
622 memcpy_fromio(dst + start, iomem + NCR53C400_host_buffer, 128);
623 #endif
624 start += 128;
625 blocks--;
628 if (!(NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ))
629 printk("53C400r: no 53C80 gated irq after transfer");
631 #if 0
633 * DON'T DO THIS - THEY NEVER ARRIVE!
635 printk("53C400r: Waiting for 53C80 registers\n");
636 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_53C80_REG)
638 #endif
639 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER))
640 printk(KERN_ERR "53C400r: no end dma signal\n");
642 NCR5380_write(MODE_REG, MR_BASE);
643 NCR5380_read(RESET_PARITY_INTERRUPT_REG);
644 return 0;
648 * NCR5380_write - pseudo DMA write
649 * @instance: adapter to read from
650 * @dst: buffer to read into
651 * @len: buffer length
653 * Perform a pseudo DMA mode read from an NCR53C400 or equivalent
654 * controller
657 static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src, int len)
659 int blocks = len / 128;
660 int start = 0;
661 int bl;
662 int i;
664 NCR5380_local_declare();
665 NCR5380_setup(instance);
667 NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE);
668 NCR5380_write(C400_BLOCK_COUNTER_REG, blocks);
669 while (1) {
670 if (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ) {
671 printk(KERN_ERR "53C400w: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks);
672 return -1;
675 if ((bl = NCR5380_read(C400_BLOCK_COUNTER_REG)) == 0) {
676 break;
678 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)
679 ; // FIXME - timeout
680 #ifndef SCSI_G_NCR5380_MEM
682 for (i = 0; i < 128; i++)
683 NCR5380_write(C400_HOST_BUFFER, src[start + i]);
685 #else
686 /* implies SCSI_G_NCR5380_MEM */
687 memcpy_toio(iomem + NCR53C400_host_buffer, src + start, 128);
688 #endif
689 start += 128;
690 blocks--;
692 if (blocks) {
693 while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)
694 ; // FIXME - no timeout
696 #ifndef SCSI_G_NCR5380_MEM
698 for (i = 0; i < 128; i++)
699 NCR5380_write(C400_HOST_BUFFER, src[start + i]);
701 #else
702 /* implies SCSI_G_NCR5380_MEM */
703 memcpy_toio(iomem + NCR53C400_host_buffer, src + start, 128);
704 #endif
705 start += 128;
706 blocks--;
709 #if 0
710 printk("53C400w: waiting for registers to be available\n");
711 THEY NEVER DO ! while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_53C80_REG);
712 printk("53C400w: Got em\n");
713 #endif
715 /* Let's wait for this instead - could be ugly */
716 /* All documentation says to check for this. Maybe my hardware is too
717 * fast. Waiting for it seems to work fine! KLL
719 while (!(i = NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ))
720 ; // FIXME - no timeout
723 * I know. i is certainly != 0 here but the loop is new. See previous
724 * comment.
726 if (i) {
727 if (!((i = NCR5380_read(BUS_AND_STATUS_REG)) & BASR_END_DMA_TRANSFER))
728 printk(KERN_ERR "53C400w: No END OF DMA bit - WHOOPS! BASR=%0x\n", i);
729 } else
730 printk(KERN_ERR "53C400w: no 53C80 gated irq after transfer (last block)\n");
732 #if 0
733 if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) {
734 printk(KERN_ERR "53C400w: no end dma signal\n");
736 #endif
737 while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT))
738 ; // TIMEOUT
739 return 0;
741 #endif /* PSEUDO_DMA */
744 * Include the NCR5380 core code that we build our driver around
747 #include "NCR5380.c"
749 #define PRINTP(x) len += sprintf(buffer+len, x)
750 #define ANDP ,
752 static int sprint_opcode(char *buffer, int len, int opcode)
754 int start = len;
755 PRINTP("0x%02x " ANDP opcode);
756 return len - start;
759 static int sprint_command(char *buffer, int len, unsigned char *command)
761 int i, s, start = len;
762 len += sprint_opcode(buffer, len, command[0]);
763 for (i = 1, s = COMMAND_SIZE(command[0]); i < s; ++i)
764 PRINTP("%02x " ANDP command[i]);
765 PRINTP("\n");
766 return len - start;
770 * sprintf_Scsi_Cmnd - print a scsi command
771 * @buffer: buffr to print into
772 * @len: buffer length
773 * @cmd: SCSI command block
775 * Print out the target and command data in hex
778 static int sprint_Scsi_Cmnd(char *buffer, int len, Scsi_Cmnd * cmd)
780 int start = len;
781 PRINTP("host number %d destination target %d, lun %d\n" ANDP cmd->device->host->host_no ANDP cmd->device->id ANDP cmd->device->lun);
782 PRINTP(" command = ");
783 len += sprint_command(buffer, len, cmd->cmnd);
784 return len - start;
788 * generic_NCR5380_proc_info - /proc for NCR5380 driver
789 * @buffer: buffer to print into
790 * @start: start position
791 * @offset: offset into buffer
792 * @len: length
793 * @hostno: instance to affect
794 * @inout: read/write
796 * Provide the procfs information for the 5380 controller. We fill
797 * this with useful debugging information including the commands
798 * being executed, disconnected command queue and the statistical
799 * data
801 * Locks: global cli/lock for queue walk
804 static int generic_NCR5380_proc_info(struct Scsi_Host *scsi_ptr, char *buffer, char **start, off_t offset, int length, int inout)
806 int len = 0;
807 NCR5380_local_declare();
808 unsigned long flags;
809 unsigned char status;
810 int i;
811 Scsi_Cmnd *ptr;
812 struct NCR5380_hostdata *hostdata;
813 #ifdef NCR5380_STATS
814 struct scsi_device *dev;
815 #endif
817 NCR5380_setup(scsi_ptr);
818 hostdata = (struct NCR5380_hostdata *) scsi_ptr->hostdata;
820 spin_lock_irqsave(scsi_ptr->host_lock, flags);
821 PRINTP("SCSI host number %d : %s\n" ANDP scsi_ptr->host_no ANDP scsi_ptr->hostt->name);
822 PRINTP("Generic NCR5380 driver version %d\n" ANDP GENERIC_NCR5380_PUBLIC_RELEASE);
823 PRINTP("NCR5380 core version %d\n" ANDP NCR5380_PUBLIC_RELEASE);
824 #ifdef NCR53C400
825 PRINTP("NCR53C400 extension version %d\n" ANDP NCR53C400_PUBLIC_RELEASE);
826 PRINTP("NCR53C400 card%s detected\n" ANDP(((struct NCR5380_hostdata *) scsi_ptr->hostdata)->flags & FLAG_NCR53C400) ? "" : " not");
827 # if NCR53C400_PSEUDO_DMA
828 PRINTP("NCR53C400 pseudo DMA used\n");
829 # endif
830 #else
831 PRINTP("NO NCR53C400 driver extensions\n");
832 #endif
833 PRINTP("Using %s mapping at %s 0x%lx, " ANDP STRVAL(NCR5380_map_config) ANDP STRVAL(NCR5380_map_name) ANDP scsi_ptr->NCR5380_instance_name);
834 if (scsi_ptr->irq == SCSI_IRQ_NONE)
835 PRINTP("no interrupt\n");
836 else
837 PRINTP("on interrupt %d\n" ANDP scsi_ptr->irq);
839 #ifdef NCR5380_STATS
840 if (hostdata->connected || hostdata->issue_queue || hostdata->disconnected_queue)
841 PRINTP("There are commands pending, transfer rates may be crud\n");
842 if (hostdata->pendingr)
843 PRINTP(" %d pending reads" ANDP hostdata->pendingr);
844 if (hostdata->pendingw)
845 PRINTP(" %d pending writes" ANDP hostdata->pendingw);
846 if (hostdata->pendingr || hostdata->pendingw)
847 PRINTP("\n");
848 shost_for_each_device(dev, scsi_ptr) {
849 unsigned long br = hostdata->bytes_read[dev->id];
850 unsigned long bw = hostdata->bytes_write[dev->id];
851 long tr = hostdata->time_read[dev->id] / HZ;
852 long tw = hostdata->time_write[dev->id] / HZ;
854 PRINTP(" T:%d %s " ANDP dev->id ANDP scsi_device_type(dev->type));
855 for (i = 0; i < 8; i++)
856 if (dev->vendor[i] >= 0x20)
857 *(buffer + (len++)) = dev->vendor[i];
858 *(buffer + (len++)) = ' ';
859 for (i = 0; i < 16; i++)
860 if (dev->model[i] >= 0x20)
861 *(buffer + (len++)) = dev->model[i];
862 *(buffer + (len++)) = ' ';
863 for (i = 0; i < 4; i++)
864 if (dev->rev[i] >= 0x20)
865 *(buffer + (len++)) = dev->rev[i];
866 *(buffer + (len++)) = ' ';
868 PRINTP("\n%10ld kb read in %5ld secs" ANDP br / 1024 ANDP tr);
869 if (tr)
870 PRINTP(" @ %5ld bps" ANDP br / tr);
872 PRINTP("\n%10ld kb written in %5ld secs" ANDP bw / 1024 ANDP tw);
873 if (tw)
874 PRINTP(" @ %5ld bps" ANDP bw / tw);
875 PRINTP("\n");
877 #endif
879 status = NCR5380_read(STATUS_REG);
880 if (!(status & SR_REQ))
881 PRINTP("REQ not asserted, phase unknown.\n");
882 else {
883 for (i = 0; (phases[i].value != PHASE_UNKNOWN) && (phases[i].value != (status & PHASE_MASK)); ++i);
884 PRINTP("Phase %s\n" ANDP phases[i].name);
887 if (!hostdata->connected) {
888 PRINTP("No currently connected command\n");
889 } else {
890 len += sprint_Scsi_Cmnd(buffer, len, (Scsi_Cmnd *) hostdata->connected);
893 PRINTP("issue_queue\n");
895 for (ptr = (Scsi_Cmnd *) hostdata->issue_queue; ptr; ptr = (Scsi_Cmnd *) ptr->host_scribble)
896 len += sprint_Scsi_Cmnd(buffer, len, ptr);
898 PRINTP("disconnected_queue\n");
900 for (ptr = (Scsi_Cmnd *) hostdata->disconnected_queue; ptr; ptr = (Scsi_Cmnd *) ptr->host_scribble)
901 len += sprint_Scsi_Cmnd(buffer, len, ptr);
903 *start = buffer + offset;
904 len -= offset;
905 if (len > length)
906 len = length;
907 spin_unlock_irqrestore(scsi_ptr->host_lock, flags);
908 return len;
911 #undef PRINTP
912 #undef ANDP
914 static struct scsi_host_template driver_template = {
915 .proc_info = generic_NCR5380_proc_info,
916 .name = "Generic NCR5380/NCR53C400 Scsi Driver",
917 .detect = generic_NCR5380_detect,
918 .release = generic_NCR5380_release_resources,
919 .info = generic_NCR5380_info,
920 .queuecommand = generic_NCR5380_queue_command,
921 .eh_abort_handler = generic_NCR5380_abort,
922 .eh_bus_reset_handler = generic_NCR5380_bus_reset,
923 .bios_param = NCR5380_BIOSPARAM,
924 .can_queue = CAN_QUEUE,
925 .this_id = 7,
926 .sg_tablesize = SG_ALL,
927 .cmd_per_lun = CMD_PER_LUN,
928 .use_clustering = DISABLE_CLUSTERING,
930 #include <linux/module.h>
931 #include "scsi_module.c"
933 module_param(ncr_irq, int, 0);
934 module_param(ncr_dma, int, 0);
935 module_param(ncr_addr, int, 0);
936 module_param(ncr_5380, int, 0);
937 module_param(ncr_53c400, int, 0);
938 module_param(ncr_53c400a, int, 0);
939 module_param(dtc_3181e, int, 0);
940 MODULE_LICENSE("GPL");
942 #ifndef SCSI_G_NCR5380_MEM
943 static struct isapnp_device_id id_table[] __devinitdata = {
945 ISAPNP_ANY_ID, ISAPNP_ANY_ID,
946 ISAPNP_VENDOR('D', 'T', 'C'), ISAPNP_FUNCTION(0x436e),
951 MODULE_DEVICE_TABLE(isapnp, id_table);
952 #endif
954 __setup("ncr5380=", do_NCR5380_setup);
955 __setup("ncr53c400=", do_NCR53C400_setup);
956 __setup("ncr53c400a=", do_NCR53C400A_setup);
957 __setup("dtc3181e=", do_DTC3181E_setup);