Linux-2.6.12-rc2
[linux-2.6/linux-acpi-2.6/ibm-acpi-2.6.git] / sound / oss / sscape.c
blob50ca646294502a4e1d5dbf84d757684bfcc5e77f
1 /*
2 * sound/sscape.c
4 * Low level driver for Ensoniq SoundScape
7 * Copyright (C) by Hannu Savolainen 1993-1997
9 * OSS/Free for Linux is distributed under the GNU GENERAL PUBLIC LICENSE (GPL)
10 * Version 2 (June 1991). See the "COPYING" file distributed with this software
11 * for more info.
14 * Thomas Sailer : ioctl code reworked (vmalloc/vfree removed)
15 * Sergey Smitienko : ensoniq p'n'p support
16 * Christoph Hellwig : adapted to module_init/module_exit
17 * Bartlomiej Zolnierkiewicz : added __init to attach_sscape()
18 * Chris Rankin : Specify that this module owns the coprocessor
19 * Arnaldo C. de Melo : added missing restore_flags in sscape_pnp_upload_file
22 #include <linux/init.h>
23 #include <linux/module.h>
25 #include "sound_config.h"
26 #include "sound_firmware.h"
28 #include <linux/types.h>
29 #include <linux/errno.h>
30 #include <linux/signal.h>
31 #include <linux/fcntl.h>
32 #include <linux/ctype.h>
33 #include <linux/stddef.h>
34 #include <linux/kmod.h>
35 #include <asm/dma.h>
36 #include <asm/io.h>
37 #include <linux/wait.h>
38 #include <linux/slab.h>
39 #include <linux/ioport.h>
40 #include <linux/delay.h>
41 #include <linux/proc_fs.h>
42 #include <linux/spinlock.h>
44 #include "coproc.h"
46 #include "ad1848.h"
47 #include "mpu401.h"
50 * I/O ports
52 #define MIDI_DATA 0
53 #define MIDI_CTRL 1
54 #define HOST_CTRL 2
55 #define TX_READY 0x02
56 #define RX_READY 0x01
57 #define HOST_DATA 3
58 #define ODIE_ADDR 4
59 #define ODIE_DATA 5
62 * Indirect registers
65 #define GA_INTSTAT_REG 0
66 #define GA_INTENA_REG 1
67 #define GA_DMAA_REG 2
68 #define GA_DMAB_REG 3
69 #define GA_INTCFG_REG 4
70 #define GA_DMACFG_REG 5
71 #define GA_CDCFG_REG 6
72 #define GA_SMCFGA_REG 7
73 #define GA_SMCFGB_REG 8
74 #define GA_HMCTL_REG 9
77 * DMA channel identifiers (A and B)
80 #define SSCAPE_DMA_A 0
81 #define SSCAPE_DMA_B 1
83 #define PORT(name) (devc->base+name)
86 * Host commands recognized by the OBP microcode
89 #define CMD_GEN_HOST_ACK 0x80
90 #define CMD_GEN_MPU_ACK 0x81
91 #define CMD_GET_BOARD_TYPE 0x82
92 #define CMD_SET_CONTROL 0x88 /* Old firmware only */
93 #define CMD_GET_CONTROL 0x89 /* Old firmware only */
94 #define CTL_MASTER_VOL 0
95 #define CTL_MIC_MODE 2
96 #define CTL_SYNTH_VOL 4
97 #define CTL_WAVE_VOL 7
98 #define CMD_SET_EXTMIDI 0x8a
99 #define CMD_GET_EXTMIDI 0x8b
100 #define CMD_SET_MT32 0x8c
101 #define CMD_GET_MT32 0x8d
103 #define CMD_ACK 0x80
105 #define IC_ODIE 1
106 #define IC_OPUS 2
108 typedef struct sscape_info
110 int base, irq, dma;
112 int codec, codec_irq; /* required to setup pnp cards*/
113 int codec_type;
114 int ic_type;
115 char* raw_buf;
116 unsigned long raw_buf_phys;
117 int buffsize; /* -------------------------- */
118 spinlock_t lock;
119 int ok; /* Properly detected */
120 int failed;
121 int dma_allocated;
122 int codec_audiodev;
123 int opened;
124 int *osp;
125 int my_audiodev;
126 } sscape_info;
128 static struct sscape_info adev_info = {
132 static struct sscape_info *devc = &adev_info;
133 static int sscape_mididev = -1;
135 /* Some older cards have assigned interrupt bits differently than new ones */
136 static char valid_interrupts_old[] = {
137 9, 7, 5, 15
140 static char valid_interrupts_new[] = {
141 9, 5, 7, 10
144 static char *valid_interrupts = valid_interrupts_new;
147 * See the bottom of the driver. This can be set by spea =0/1.
150 #ifdef REVEAL_SPEA
151 static char old_hardware = 1;
152 #else
153 static char old_hardware;
154 #endif
156 static void sleep(unsigned howlong)
158 current->state = TASK_INTERRUPTIBLE;
159 schedule_timeout(howlong);
162 static unsigned char sscape_read(struct sscape_info *devc, int reg)
164 unsigned long flags;
165 unsigned char val;
167 spin_lock_irqsave(&devc->lock,flags);
168 outb(reg, PORT(ODIE_ADDR));
169 val = inb(PORT(ODIE_DATA));
170 spin_unlock_irqrestore(&devc->lock,flags);
171 return val;
174 static void __sscape_write(int reg, int data)
176 outb(reg, PORT(ODIE_ADDR));
177 outb(data, PORT(ODIE_DATA));
180 static void sscape_write(struct sscape_info *devc, int reg, int data)
182 unsigned long flags;
184 spin_lock_irqsave(&devc->lock,flags);
185 __sscape_write(reg, data);
186 spin_unlock_irqrestore(&devc->lock,flags);
189 static unsigned char sscape_pnp_read_codec(sscape_info* devc, unsigned char reg)
191 unsigned char res;
192 unsigned long flags;
194 spin_lock_irqsave(&devc->lock,flags);
195 outb( reg, devc -> codec);
196 res = inb (devc -> codec + 1);
197 spin_unlock_irqrestore(&devc->lock,flags);
198 return res;
202 static void sscape_pnp_write_codec(sscape_info* devc, unsigned char reg, unsigned char data)
204 unsigned long flags;
206 spin_lock_irqsave(&devc->lock,flags);
207 outb( reg, devc -> codec);
208 outb( data, devc -> codec + 1);
209 spin_unlock_irqrestore(&devc->lock,flags);
212 static void host_open(struct sscape_info *devc)
214 outb((0x00), PORT(HOST_CTRL)); /* Put the board to the host mode */
217 static void host_close(struct sscape_info *devc)
219 outb((0x03), PORT(HOST_CTRL)); /* Put the board to the MIDI mode */
222 static int host_write(struct sscape_info *devc, unsigned char *data, int count)
224 unsigned long flags;
225 int i, timeout_val;
227 spin_lock_irqsave(&devc->lock,flags);
229 * Send the command and data bytes
232 for (i = 0; i < count; i++)
234 for (timeout_val = 10000; timeout_val > 0; timeout_val--)
235 if (inb(PORT(HOST_CTRL)) & TX_READY)
236 break;
238 if (timeout_val <= 0)
240 spin_unlock_irqrestore(&devc->lock,flags);
241 return 0;
243 outb(data[i], PORT(HOST_DATA));
245 spin_unlock_irqrestore(&devc->lock,flags);
246 return 1;
249 static int host_read(struct sscape_info *devc)
251 unsigned long flags;
252 int timeout_val;
253 unsigned char data;
255 spin_lock_irqsave(&devc->lock,flags);
257 * Read a byte
260 for (timeout_val = 10000; timeout_val > 0; timeout_val--)
261 if (inb(PORT(HOST_CTRL)) & RX_READY)
262 break;
264 if (timeout_val <= 0)
266 spin_unlock_irqrestore(&devc->lock,flags);
267 return -1;
269 data = inb(PORT(HOST_DATA));
270 spin_unlock_irqrestore(&devc->lock,flags);
271 return data;
274 #if 0 /* unused */
275 static int host_command1(struct sscape_info *devc, int cmd)
277 unsigned char buf[10];
278 buf[0] = (unsigned char) (cmd & 0xff);
279 return host_write(devc, buf, 1);
281 #endif /* unused */
284 static int host_command2(struct sscape_info *devc, int cmd, int parm1)
286 unsigned char buf[10];
288 buf[0] = (unsigned char) (cmd & 0xff);
289 buf[1] = (unsigned char) (parm1 & 0xff);
291 return host_write(devc, buf, 2);
294 static int host_command3(struct sscape_info *devc, int cmd, int parm1, int parm2)
296 unsigned char buf[10];
298 buf[0] = (unsigned char) (cmd & 0xff);
299 buf[1] = (unsigned char) (parm1 & 0xff);
300 buf[2] = (unsigned char) (parm2 & 0xff);
301 return host_write(devc, buf, 3);
304 static void set_mt32(struct sscape_info *devc, int value)
306 host_open(devc);
307 host_command2(devc, CMD_SET_MT32, value ? 1 : 0);
308 if (host_read(devc) != CMD_ACK)
310 /* printk( "SNDSCAPE: Setting MT32 mode failed\n"); */
312 host_close(devc);
315 static void set_control(struct sscape_info *devc, int ctrl, int value)
317 host_open(devc);
318 host_command3(devc, CMD_SET_CONTROL, ctrl, value);
319 if (host_read(devc) != CMD_ACK)
321 /* printk( "SNDSCAPE: Setting control (%d) failed\n", ctrl); */
323 host_close(devc);
326 static void do_dma(struct sscape_info *devc, int dma_chan, unsigned long buf, int blk_size, int mode)
328 unsigned char temp;
330 if (dma_chan != SSCAPE_DMA_A)
332 printk(KERN_WARNING "soundscape: Tried to use DMA channel != A. Why?\n");
333 return;
335 audio_devs[devc->codec_audiodev]->flags &= ~DMA_AUTOMODE;
336 DMAbuf_start_dma(devc->codec_audiodev, buf, blk_size, mode);
337 audio_devs[devc->codec_audiodev]->flags |= DMA_AUTOMODE;
339 temp = devc->dma << 4; /* Setup DMA channel select bits */
340 if (devc->dma <= 3)
341 temp |= 0x80; /* 8 bit DMA channel */
343 temp |= 1; /* Trigger DMA */
344 sscape_write(devc, GA_DMAA_REG, temp);
345 temp &= 0xfe; /* Clear DMA trigger */
346 sscape_write(devc, GA_DMAA_REG, temp);
349 static int verify_mpu(struct sscape_info *devc)
352 * The SoundScape board could be in three modes (MPU, 8250 and host).
353 * If the card is not in the MPU mode, enabling the MPU driver will
354 * cause infinite loop (the driver believes that there is always some
355 * received data in the buffer.
357 * Detect this by looking if there are more than 10 received MIDI bytes
358 * (0x00) in the buffer.
361 int i;
363 for (i = 0; i < 10; i++)
365 if (inb(devc->base + HOST_CTRL) & 0x80)
366 return 1;
368 if (inb(devc->base) != 0x00)
369 return 1;
371 printk(KERN_WARNING "SoundScape: The device is not in the MPU-401 mode\n");
372 return 0;
375 static int sscape_coproc_open(void *dev_info, int sub_device)
377 if (sub_device == COPR_MIDI)
379 set_mt32(devc, 0);
380 if (!verify_mpu(devc))
381 return -EIO;
383 return 0;
386 static void sscape_coproc_close(void *dev_info, int sub_device)
388 struct sscape_info *devc = dev_info;
389 unsigned long flags;
391 spin_lock_irqsave(&devc->lock,flags);
392 if (devc->dma_allocated)
394 __sscape_write(GA_DMAA_REG, 0x20); /* DMA channel disabled */
395 devc->dma_allocated = 0;
397 spin_unlock_irqrestore(&devc->lock,flags);
398 return;
401 static void sscape_coproc_reset(void *dev_info)
405 static int sscape_download_boot(struct sscape_info *devc, unsigned char *block, int size, int flag)
407 unsigned long flags;
408 unsigned char temp;
409 volatile int done, timeout_val;
410 static unsigned char codec_dma_bits;
412 if (flag & CPF_FIRST)
415 * First block. Have to allocate DMA and to reset the board
416 * before continuing.
419 spin_lock_irqsave(&devc->lock,flags);
420 codec_dma_bits = sscape_read(devc, GA_CDCFG_REG);
422 if (devc->dma_allocated == 0)
423 devc->dma_allocated = 1;
425 spin_unlock_irqrestore(&devc->lock,flags);
427 sscape_write(devc, GA_HMCTL_REG,
428 (temp = sscape_read(devc, GA_HMCTL_REG)) & 0x3f); /*Reset */
430 for (timeout_val = 10000; timeout_val > 0; timeout_val--)
431 sscape_read(devc, GA_HMCTL_REG); /* Delay */
433 /* Take board out of reset */
434 sscape_write(devc, GA_HMCTL_REG,
435 (temp = sscape_read(devc, GA_HMCTL_REG)) | 0x80);
438 * Transfer one code block using DMA
440 if (audio_devs[devc->codec_audiodev]->dmap_out->raw_buf == NULL)
442 printk(KERN_WARNING "soundscape: DMA buffer not available\n");
443 return 0;
445 memcpy(audio_devs[devc->codec_audiodev]->dmap_out->raw_buf, block, size);
447 spin_lock_irqsave(&devc->lock,flags);
449 /******** INTERRUPTS DISABLED NOW ********/
451 do_dma(devc, SSCAPE_DMA_A,
452 audio_devs[devc->codec_audiodev]->dmap_out->raw_buf_phys,
453 size, DMA_MODE_WRITE);
456 * Wait until transfer completes.
459 done = 0;
460 timeout_val = 30;
461 while (!done && timeout_val-- > 0)
463 int resid;
465 if (HZ / 50)
466 sleep(HZ / 50);
467 clear_dma_ff(devc->dma);
468 if ((resid = get_dma_residue(devc->dma)) == 0)
469 done = 1;
472 spin_unlock_irqrestore(&devc->lock,flags);
473 if (!done)
474 return 0;
476 if (flag & CPF_LAST)
479 * Take the board out of reset
481 outb((0x00), PORT(HOST_CTRL));
482 outb((0x00), PORT(MIDI_CTRL));
484 temp = sscape_read(devc, GA_HMCTL_REG);
485 temp |= 0x40;
486 sscape_write(devc, GA_HMCTL_REG, temp); /* Kickstart the board */
489 * Wait until the ODB wakes up
491 spin_lock_irqsave(&devc->lock,flags);
492 done = 0;
493 timeout_val = 5 * HZ;
494 while (!done && timeout_val-- > 0)
496 unsigned char x;
498 sleep(1);
499 x = inb(PORT(HOST_DATA));
500 if (x == 0xff || x == 0xfe) /* OBP startup acknowledge */
502 DDB(printk("Soundscape: Acknowledge = %x\n", x));
503 done = 1;
506 sscape_write(devc, GA_CDCFG_REG, codec_dma_bits);
508 spin_unlock_irqrestore(&devc->lock,flags);
509 if (!done)
511 printk(KERN_ERR "soundscape: The OBP didn't respond after code download\n");
512 return 0;
514 spin_lock_irqsave(&devc->lock,flags);
515 done = 0;
516 timeout_val = 5 * HZ;
517 while (!done && timeout_val-- > 0)
519 sleep(1);
520 if (inb(PORT(HOST_DATA)) == 0xfe) /* Host startup acknowledge */
521 done = 1;
523 spin_unlock_irqrestore(&devc->lock,flags);
524 if (!done)
526 printk(KERN_ERR "soundscape: OBP Initialization failed.\n");
527 return 0;
529 printk(KERN_INFO "SoundScape board initialized OK\n");
530 set_control(devc, CTL_MASTER_VOL, 100);
531 set_control(devc, CTL_SYNTH_VOL, 100);
533 #ifdef SSCAPE_DEBUG3
535 * Temporary debugging aid. Print contents of the registers after
536 * downloading the code.
539 int i;
541 for (i = 0; i < 13; i++)
542 printk("I%d = %02x (new value)\n", i, sscape_read(devc, i));
544 #endif
547 return 1;
550 static int download_boot_block(void *dev_info, copr_buffer * buf)
552 if (buf->len <= 0 || buf->len > sizeof(buf->data))
553 return -EINVAL;
555 if (!sscape_download_boot(devc, buf->data, buf->len, buf->flags))
557 printk(KERN_ERR "soundscape: Unable to load microcode block to the OBP.\n");
558 return -EIO;
560 return 0;
563 static int sscape_coproc_ioctl(void *dev_info, unsigned int cmd, void __user *arg, int local)
565 copr_buffer *buf;
566 int err;
568 switch (cmd)
570 case SNDCTL_COPR_RESET:
571 sscape_coproc_reset(dev_info);
572 return 0;
574 case SNDCTL_COPR_LOAD:
575 buf = (copr_buffer *) vmalloc(sizeof(copr_buffer));
576 if (buf == NULL)
577 return -ENOSPC;
578 if (copy_from_user(buf, arg, sizeof(copr_buffer)))
580 vfree(buf);
581 return -EFAULT;
583 err = download_boot_block(dev_info, buf);
584 vfree(buf);
585 return err;
587 default:
588 return -EINVAL;
592 static coproc_operations sscape_coproc_operations =
594 "SoundScape M68K",
595 THIS_MODULE,
596 sscape_coproc_open,
597 sscape_coproc_close,
598 sscape_coproc_ioctl,
599 sscape_coproc_reset,
600 &adev_info
603 static struct resource *sscape_ports;
604 static int sscape_is_pnp;
606 static void __init attach_sscape(struct address_info *hw_config)
608 #ifndef SSCAPE_REGS
610 * Config register values for Spea/V7 Media FX and Ensoniq S-2000.
611 * These values are card
612 * dependent. If you have another SoundScape based card, you have to
613 * find the correct values. Do the following:
614 * - Compile this driver with SSCAPE_DEBUG1 defined.
615 * - Shut down and power off your machine.
616 * - Boot with DOS so that the SSINIT.EXE program is run.
617 * - Warm boot to {Linux|SYSV|BSD} and write down the lines displayed
618 * when detecting the SoundScape.
619 * - Modify the following list to use the values printed during boot.
620 * Undefine the SSCAPE_DEBUG1
622 #define SSCAPE_REGS { \
623 /* I0 */ 0x00, \
624 /* I1 */ 0xf0, /* Note! Ignored. Set always to 0xf0 */ \
625 /* I2 */ 0x20, /* Note! Ignored. Set always to 0x20 */ \
626 /* I3 */ 0x20, /* Note! Ignored. Set always to 0x20 */ \
627 /* I4 */ 0xf5, /* Ignored */ \
628 /* I5 */ 0x10, \
629 /* I6 */ 0x00, \
630 /* I7 */ 0x2e, /* I7 MEM config A. Likely to vary between models */ \
631 /* I8 */ 0x00, /* I8 MEM config B. Likely to vary between models */ \
632 /* I9 */ 0x40 /* Ignored */ \
634 #endif
636 unsigned long flags;
637 static unsigned char regs[10] = SSCAPE_REGS;
639 int i, irq_bits = 0xff;
641 if (old_hardware)
643 valid_interrupts = valid_interrupts_old;
644 conf_printf("Ensoniq SoundScape (old)", hw_config);
646 else
647 conf_printf("Ensoniq SoundScape", hw_config);
649 for (i = 0; i < 4; i++)
651 if (hw_config->irq == valid_interrupts[i])
653 irq_bits = i;
654 break;
657 if (hw_config->irq > 15 || (regs[4] = irq_bits == 0xff))
659 printk(KERN_ERR "Invalid IRQ%d\n", hw_config->irq);
660 release_region(devc->base, 2);
661 release_region(devc->base + 2, 6);
662 if (sscape_is_pnp)
663 release_region(devc->codec, 2);
664 return;
667 if (!sscape_is_pnp) {
669 spin_lock_irqsave(&devc->lock,flags);
670 /* Host interrupt enable */
671 sscape_write(devc, 1, 0xf0); /* All interrupts enabled */
672 /* DMA A status/trigger register */
673 sscape_write(devc, 2, 0x20); /* DMA channel disabled */
674 /* DMA B status/trigger register */
675 sscape_write(devc, 3, 0x20); /* DMA channel disabled */
676 /* Host interrupt config reg */
677 sscape_write(devc, 4, 0xf0 | (irq_bits << 2) | irq_bits);
678 /* Don't destroy CD-ROM DMA config bits (0xc0) */
679 sscape_write(devc, 5, (regs[5] & 0x3f) | (sscape_read(devc, 5) & 0xc0));
680 /* CD-ROM config (WSS codec actually) */
681 sscape_write(devc, 6, regs[6]);
682 sscape_write(devc, 7, regs[7]);
683 sscape_write(devc, 8, regs[8]);
684 /* Master control reg. Don't modify CR-ROM bits. Disable SB emul */
685 sscape_write(devc, 9, (sscape_read(devc, 9) & 0xf0) | 0x08);
686 spin_unlock_irqrestore(&devc->lock,flags);
688 #ifdef SSCAPE_DEBUG2
690 * Temporary debugging aid. Print contents of the registers after
691 * changing them.
694 int i;
696 for (i = 0; i < 13; i++)
697 printk("I%d = %02x (new value)\n", i, sscape_read(devc, i));
699 #endif
701 if (probe_mpu401(hw_config, sscape_ports))
702 hw_config->always_detect = 1;
703 hw_config->name = "SoundScape";
705 hw_config->irq *= -1; /* Negative value signals IRQ sharing */
706 attach_mpu401(hw_config, THIS_MODULE);
707 hw_config->irq *= -1; /* Restore it */
709 if (hw_config->slots[1] != -1) /* The MPU driver installed itself */
711 sscape_mididev = hw_config->slots[1];
712 midi_devs[hw_config->slots[1]]->coproc = &sscape_coproc_operations;
714 sscape_write(devc, GA_INTENA_REG, 0x80); /* Master IRQ enable */
715 devc->ok = 1;
716 devc->failed = 0;
719 static int detect_ga(sscape_info * devc)
721 unsigned char save;
723 DDB(printk("Entered Soundscape detect_ga(%x)\n", devc->base));
726 * First check that the address register of "ODIE" is
727 * there and that it has exactly 4 writable bits.
728 * First 4 bits
731 if ((save = inb(PORT(ODIE_ADDR))) & 0xf0)
733 DDB(printk("soundscape: Detect error A\n"));
734 return 0;
736 outb((0x00), PORT(ODIE_ADDR));
737 if (inb(PORT(ODIE_ADDR)) != 0x00)
739 DDB(printk("soundscape: Detect error B\n"));
740 return 0;
742 outb((0xff), PORT(ODIE_ADDR));
743 if (inb(PORT(ODIE_ADDR)) != 0x0f)
745 DDB(printk("soundscape: Detect error C\n"));
746 return 0;
748 outb((save), PORT(ODIE_ADDR));
751 * Now verify that some indirect registers return zero on some bits.
752 * This may break the driver with some future revisions of "ODIE" but...
755 if (sscape_read(devc, 0) & 0x0c)
757 DDB(printk("soundscape: Detect error D (%x)\n", sscape_read(devc, 0)));
758 return 0;
760 if (sscape_read(devc, 1) & 0x0f)
762 DDB(printk("soundscape: Detect error E\n"));
763 return 0;
765 if (sscape_read(devc, 5) & 0x0f)
767 DDB(printk("soundscape: Detect error F\n"));
768 return 0;
770 return 1;
773 static int sscape_read_host_ctrl(sscape_info* devc)
775 return host_read(devc);
778 static void sscape_write_host_ctrl2(sscape_info *devc, int a, int b)
780 host_command2(devc, a, b);
783 static int sscape_alloc_dma(sscape_info *devc)
785 char *start_addr, *end_addr;
786 int dma_pagesize;
787 int sz, size;
788 struct page *page;
790 if (devc->raw_buf != NULL) return 0; /* Already done */
791 dma_pagesize = (devc->dma < 4) ? (64 * 1024) : (128 * 1024);
792 devc->raw_buf = NULL;
793 devc->buffsize = 8192*4;
794 if (devc->buffsize > dma_pagesize) devc->buffsize = dma_pagesize;
795 start_addr = NULL;
797 * Now loop until we get a free buffer. Try to get smaller buffer if
798 * it fails. Don't accept smaller than 8k buffer for performance
799 * reasons.
801 while (start_addr == NULL && devc->buffsize > PAGE_SIZE) {
802 for (sz = 0, size = PAGE_SIZE; size < devc->buffsize; sz++, size <<= 1);
803 devc->buffsize = PAGE_SIZE * (1 << sz);
804 start_addr = (char *) __get_free_pages(GFP_ATOMIC|GFP_DMA, sz);
805 if (start_addr == NULL) devc->buffsize /= 2;
808 if (start_addr == NULL) {
809 printk(KERN_ERR "sscape pnp init error: Couldn't allocate DMA buffer\n");
810 return 0;
811 } else {
812 /* make some checks */
813 end_addr = start_addr + devc->buffsize - 1;
814 /* now check if it fits into the same dma-pagesize */
816 if (((long) start_addr & ~(dma_pagesize - 1)) != ((long) end_addr & ~(dma_pagesize - 1))
817 || end_addr >= (char *) (MAX_DMA_ADDRESS)) {
818 printk(KERN_ERR "sscape pnp: Got invalid address 0x%lx for %db DMA-buffer\n", (long) start_addr, devc->buffsize);
819 return 0;
822 devc->raw_buf = start_addr;
823 devc->raw_buf_phys = virt_to_bus(start_addr);
825 for (page = virt_to_page(start_addr); page <= virt_to_page(end_addr); page++)
826 SetPageReserved(page);
827 return 1;
830 static void sscape_free_dma(sscape_info *devc)
832 int sz, size;
833 unsigned long start_addr, end_addr;
834 struct page *page;
836 if (devc->raw_buf == NULL) return;
837 for (sz = 0, size = PAGE_SIZE; size < devc->buffsize; sz++, size <<= 1);
838 start_addr = (unsigned long) devc->raw_buf;
839 end_addr = start_addr + devc->buffsize;
841 for (page = virt_to_page(start_addr); page <= virt_to_page(end_addr); page++)
842 ClearPageReserved(page);
844 free_pages((unsigned long) devc->raw_buf, sz);
845 devc->raw_buf = NULL;
848 /* Intel version !!!!!!!!! */
850 static int sscape_start_dma(int chan, unsigned long physaddr, int count, int dma_mode)
852 unsigned long flags;
854 flags = claim_dma_lock();
855 disable_dma(chan);
856 clear_dma_ff(chan);
857 set_dma_mode(chan, dma_mode);
858 set_dma_addr(chan, physaddr);
859 set_dma_count(chan, count);
860 enable_dma(chan);
861 release_dma_lock(flags);
862 return 0;
865 static void sscape_pnp_start_dma(sscape_info* devc, int arg )
867 int reg;
868 if (arg == 0) reg = 2;
869 else reg = 3;
871 sscape_write(devc, reg, sscape_read( devc, reg) | 0x01);
872 sscape_write(devc, reg, sscape_read( devc, reg) & 0xFE);
875 static int sscape_pnp_wait_dma (sscape_info* devc, int arg )
877 int reg;
878 unsigned long i;
879 unsigned char d;
881 if (arg == 0) reg = 2;
882 else reg = 3;
884 sleep ( 1 );
885 i = 0;
886 do {
887 d = sscape_read(devc, reg) & 1;
888 if ( d == 1) break;
889 i++;
890 } while (i < 500000);
891 d = sscape_read(devc, reg) & 1;
892 return d;
895 static int sscape_pnp_alloc_dma(sscape_info* devc)
897 /* printk(KERN_INFO "sscape: requesting dma\n"); */
898 if (request_dma(devc -> dma, "sscape")) return 0;
899 /* printk(KERN_INFO "sscape: dma channel allocated\n"); */
900 if (!sscape_alloc_dma(devc)) {
901 free_dma(devc -> dma);
902 return 0;
904 return 1;
907 static void sscape_pnp_free_dma(sscape_info* devc)
909 sscape_free_dma( devc);
910 free_dma(devc -> dma );
911 /* printk(KERN_INFO "sscape: dma released\n"); */
914 static int sscape_pnp_upload_file(sscape_info* devc, char* fn)
916 int done = 0;
917 int timeout_val;
918 char* data,*dt;
919 int len,l;
920 unsigned long flags;
922 sscape_write( devc, 9, sscape_read(devc, 9 ) & 0x3F );
923 sscape_write( devc, 2, (devc -> dma << 4) | 0x80 );
924 sscape_write( devc, 3, 0x20 );
925 sscape_write( devc, 9, sscape_read( devc, 9 ) | 0x80 );
927 len = mod_firmware_load(fn, &data);
928 if (len == 0) {
929 printk(KERN_ERR "sscape: file not found: %s\n", fn);
930 return 0;
932 dt = data;
933 spin_lock_irqsave(&devc->lock,flags);
934 while ( len > 0 ) {
935 if (len > devc -> buffsize) l = devc->buffsize;
936 else l = len;
937 len -= l;
938 memcpy(devc->raw_buf, dt, l); dt += l;
939 sscape_start_dma(devc->dma, devc->raw_buf_phys, l, 0x48);
940 sscape_pnp_start_dma ( devc, 0 );
941 if (sscape_pnp_wait_dma ( devc, 0 ) == 0) {
942 spin_unlock_irqrestore(&devc->lock,flags);
943 return 0;
947 spin_unlock_irqrestore(&devc->lock,flags);
948 vfree(data);
950 outb(0, devc -> base + 2);
951 outb(0, devc -> base);
953 sscape_write ( devc, 9, sscape_read( devc, 9 ) | 0x40);
955 timeout_val = 5 * HZ;
956 while (!done && timeout_val-- > 0)
958 unsigned char x;
959 sleep(1);
960 x = inb( devc -> base + 3);
961 if (x == 0xff || x == 0xfe) /* OBP startup acknowledge */
963 //printk(KERN_ERR "Soundscape: Acknowledge = %x\n", x);
964 done = 1;
967 timeout_val = 5 * HZ;
968 done = 0;
969 while (!done && timeout_val-- > 0)
971 unsigned char x;
972 sleep(1);
973 x = inb( devc -> base + 3);
974 if (x == 0xfe) /* OBP startup acknowledge */
976 //printk(KERN_ERR "Soundscape: Acknowledge = %x\n", x);
977 done = 1;
981 if ( !done ) printk(KERN_ERR "soundscape: OBP Initialization failed.\n");
983 sscape_write( devc, 2, devc->ic_type == IC_ODIE ? 0x70 : 0x40);
984 sscape_write( devc, 3, (devc -> dma << 4) + 0x80);
985 return 1;
988 static void __init sscape_pnp_init_hw(sscape_info* devc)
990 unsigned char midi_irq = 0, sb_irq = 0;
991 unsigned i;
992 static char code_file_name[23] = "/sndscape/sndscape.cox";
994 int sscape_sb_enable = 0;
995 int sscape_joystic_enable = 0x7f;
996 int sscape_mic_enable = 0;
997 int sscape_ext_midi = 0;
999 if ( !sscape_pnp_alloc_dma(devc) ) {
1000 printk(KERN_ERR "sscape: faild to allocate dma\n");
1001 return;
1004 for (i = 0; i < 4; i++) {
1005 if ( devc -> irq == valid_interrupts[i] )
1006 midi_irq = i;
1007 if ( devc -> codec_irq == valid_interrupts[i] )
1008 sb_irq = i;
1011 sscape_write( devc, 5, 0x50);
1012 sscape_write( devc, 7, 0x2e);
1013 sscape_write( devc, 8, 0x00);
1015 sscape_write( devc, 2, devc->ic_type == IC_ODIE ? 0x70 : 0x40);
1016 sscape_write( devc, 3, ( devc -> dma << 4) | 0x80);
1018 if ( sscape_sb_enable )
1019 sscape_write (devc, 4, 0xF0 | (sb_irq << 2) | midi_irq);
1020 else
1021 sscape_write (devc, 4, 0xF0 | (midi_irq<<2) | midi_irq);
1023 i = 0x10; //sscape_read(devc, 9) & (devc->ic_type == IC_ODIE ? 0xf0 : 0xc0);
1024 if ( sscape_sb_enable )
1025 i |= devc->ic_type == IC_ODIE ? 0x05 : 0x07;
1026 if (sscape_joystic_enable) i |= 8;
1028 sscape_write (devc, 9, i);
1029 sscape_write (devc, 6, 0x80);
1030 sscape_write (devc, 1, 0x80);
1032 if (devc -> codec_type == 2) {
1033 sscape_pnp_write_codec( devc, 0x0C, 0x50);
1034 sscape_pnp_write_codec( devc, 0x10, sscape_pnp_read_codec( devc, 0x10) & 0x3F);
1035 sscape_pnp_write_codec( devc, 0x11, sscape_pnp_read_codec( devc, 0x11) | 0xC0);
1036 sscape_pnp_write_codec( devc, 29, 0x20);
1039 if (sscape_pnp_upload_file(devc, "/sndscape/scope.cod") == 0 ) {
1040 printk(KERN_ERR "sscape: faild to upload file /sndscape/scope.cod\n");
1041 sscape_pnp_free_dma(devc);
1042 return;
1045 i = sscape_read_host_ctrl( devc );
1047 if ( (i & 0x0F) > 7 ) {
1048 printk(KERN_ERR "sscape: scope.cod faild\n");
1049 sscape_pnp_free_dma(devc);
1050 return;
1052 if ( i & 0x10 ) sscape_write( devc, 7, 0x2F);
1053 code_file_name[21] = (char) ( i & 0x0F) + 0x30;
1054 if (sscape_pnp_upload_file( devc, code_file_name) == 0) {
1055 printk(KERN_ERR "sscape: faild to upload file %s\n", code_file_name);
1056 sscape_pnp_free_dma(devc);
1057 return;
1060 if (devc->ic_type != IC_ODIE) {
1061 sscape_pnp_write_codec( devc, 10, (sscape_pnp_read_codec(devc, 10) & 0x7f) |
1062 ( sscape_mic_enable == 0 ? 0x00 : 0x80) );
1064 sscape_write_host_ctrl2( devc, 0x84, 0x64 ); /* MIDI volume */
1065 sscape_write_host_ctrl2( devc, 0x86, 0x64 ); /* MIDI volume?? */
1066 sscape_write_host_ctrl2( devc, 0x8A, sscape_ext_midi);
1068 sscape_pnp_write_codec ( devc, 6, 0x3f ); //WAV_VOL
1069 sscape_pnp_write_codec ( devc, 7, 0x3f ); //WAV_VOL
1070 sscape_pnp_write_codec ( devc, 2, 0x1F ); //WD_CDXVOLL
1071 sscape_pnp_write_codec ( devc, 3, 0x1F ); //WD_CDXVOLR
1073 if (devc -> codec_type == 1) {
1074 sscape_pnp_write_codec ( devc, 4, 0x1F );
1075 sscape_pnp_write_codec ( devc, 5, 0x1F );
1076 sscape_write_host_ctrl2( devc, 0x88, sscape_mic_enable);
1077 } else {
1078 int t;
1079 sscape_pnp_write_codec ( devc, 0x10, 0x1F << 1);
1080 sscape_pnp_write_codec ( devc, 0x11, 0xC0 | (0x1F << 1));
1082 t = sscape_pnp_read_codec( devc, 0x00) & 0xDF;
1083 if ( (sscape_mic_enable == 0)) t |= 0;
1084 else t |= 0x20;
1085 sscape_pnp_write_codec ( devc, 0x00, t);
1086 t = sscape_pnp_read_codec( devc, 0x01) & 0xDF;
1087 if ( (sscape_mic_enable == 0) ) t |= 0;
1088 else t |= 0x20;
1089 sscape_pnp_write_codec ( devc, 0x01, t);
1090 sscape_pnp_write_codec ( devc, 0x40 | 29 , 0x20);
1091 outb(0, devc -> codec);
1093 if (devc -> ic_type == IC_OPUS ) {
1094 int i = sscape_read( devc, 9 );
1095 sscape_write( devc, 9, i | 3 );
1096 sscape_write( devc, 3, 0x40);
1098 if (request_region(0x228, 1, "sscape setup junk")) {
1099 outb(0, 0x228);
1100 release_region(0x228,1);
1102 sscape_write( devc, 3, (devc -> dma << 4) | 0x80);
1103 sscape_write( devc, 9, i );
1106 host_close ( devc );
1107 sscape_pnp_free_dma(devc);
1110 static int __init detect_sscape_pnp(sscape_info* devc)
1112 long i, irq_bits = 0xff;
1113 unsigned int d;
1115 DDB(printk("Entered detect_sscape_pnp(%x)\n", devc->base));
1117 if (!request_region(devc->codec, 2, "sscape codec")) {
1118 printk(KERN_ERR "detect_sscape_pnp: port %x is not free\n", devc->codec);
1119 return 0;
1122 if ((inb(devc->base + 2) & 0x78) != 0)
1123 goto fail;
1125 d = inb ( devc -> base + 4) & 0xF0;
1126 if (d & 0x80)
1127 goto fail;
1129 if (d == 0) {
1130 devc->codec_type = 1;
1131 devc->ic_type = IC_ODIE;
1132 } else if ( (d & 0x60) != 0) {
1133 devc->codec_type = 2;
1134 devc->ic_type = IC_OPUS;
1135 } else if ( (d & 0x40) != 0) { /* WTF? */
1136 devc->codec_type = 2;
1137 devc->ic_type = IC_ODIE;
1138 } else
1139 goto fail;
1141 sscape_is_pnp = 1;
1143 outb(0xFA, devc -> base+4);
1144 if ((inb( devc -> base+4) & 0x9F) != 0x0A)
1145 goto fail;
1146 outb(0xFE, devc -> base+4);
1147 if ( (inb(devc -> base+4) & 0x9F) != 0x0E)
1148 goto fail;
1149 if ( (inb(devc -> base+5) & 0x9F) != 0x0E)
1150 goto fail;
1152 if (devc->codec_type == 2) {
1153 if (devc->codec != devc->base + 8) {
1154 printk("soundscape warning: incorrect codec port specified\n");
1155 goto fail;
1157 d = 0x10 | (sscape_read(devc, 9) & 0xCF);
1158 sscape_write(devc, 9, d);
1159 sscape_write(devc, 6, 0x80);
1160 } else {
1161 //todo: check codec is not base + 8
1164 d = (sscape_read(devc, 9) & 0x3F) | 0xC0;
1165 sscape_write(devc, 9, d);
1167 for (i = 0; i < 550000; i++)
1168 if ( !(inb(devc -> codec) & 0x80) ) break;
1170 d = inb(devc -> codec);
1171 if (d & 0x80)
1172 goto fail;
1173 if ( inb(devc -> codec + 2) == 0xFF)
1174 goto fail;
1176 sscape_write(devc, 9, sscape_read(devc, 9) & 0x3F );
1178 d = inb(devc -> codec) & 0x80;
1179 if ( d == 0) {
1180 printk(KERN_INFO "soundscape: hardware detected\n");
1181 valid_interrupts = valid_interrupts_new;
1182 } else {
1183 printk(KERN_INFO "soundscape: board looks like media fx\n");
1184 valid_interrupts = valid_interrupts_old;
1185 old_hardware = 1;
1188 sscape_write( devc, 9, 0xC0 | (sscape_read(devc, 9) & 0x3F) );
1190 for (i = 0; i < 550000; i++)
1191 if ( !(inb(devc -> codec) & 0x80))
1192 break;
1194 sscape_pnp_init_hw(devc);
1196 for (i = 0; i < 4; i++)
1198 if (devc->codec_irq == valid_interrupts[i]) {
1199 irq_bits = i;
1200 break;
1203 sscape_write(devc, GA_INTENA_REG, 0x00);
1204 sscape_write(devc, GA_DMACFG_REG, 0x50);
1205 sscape_write(devc, GA_DMAA_REG, 0x70);
1206 sscape_write(devc, GA_DMAB_REG, 0x20);
1207 sscape_write(devc, GA_INTCFG_REG, 0xf0);
1208 sscape_write(devc, GA_CDCFG_REG, 0x89 | (devc->dma << 4) | (irq_bits << 1));
1210 sscape_pnp_write_codec( devc, 0, sscape_pnp_read_codec( devc, 0) | 0x20);
1211 sscape_pnp_write_codec( devc, 0, sscape_pnp_read_codec( devc, 1) | 0x20);
1213 return 1;
1214 fail:
1215 release_region(devc->codec, 2);
1216 return 0;
1219 static int __init probe_sscape(struct address_info *hw_config)
1221 devc->base = hw_config->io_base;
1222 devc->irq = hw_config->irq;
1223 devc->dma = hw_config->dma;
1224 devc->osp = hw_config->osp;
1226 #ifdef SSCAPE_DEBUG1
1228 * Temporary debugging aid. Print contents of the registers before
1229 * changing them.
1232 int i;
1234 for (i = 0; i < 13; i++)
1235 printk("I%d = %02x (old value)\n", i, sscape_read(devc, i));
1237 #endif
1238 devc->failed = 1;
1240 sscape_ports = request_region(devc->base, 2, "mpu401");
1241 if (!sscape_ports)
1242 return 0;
1244 if (!request_region(devc->base + 2, 6, "SoundScape")) {
1245 release_region(devc->base, 2);
1246 return 0;
1249 if (!detect_ga(devc)) {
1250 if (detect_sscape_pnp(devc))
1251 return 1;
1252 release_region(devc->base, 2);
1253 release_region(devc->base + 2, 6);
1254 return 0;
1257 if (old_hardware) /* Check that it's really an old Spea/Reveal card. */
1259 unsigned char tmp;
1260 int cc;
1262 if (!((tmp = sscape_read(devc, GA_HMCTL_REG)) & 0xc0))
1264 sscape_write(devc, GA_HMCTL_REG, tmp | 0x80);
1265 for (cc = 0; cc < 200000; ++cc)
1266 inb(devc->base + ODIE_ADDR);
1269 return 1;
1272 static int __init init_ss_ms_sound(struct address_info *hw_config)
1274 int i, irq_bits = 0xff;
1275 int ad_flags = 0;
1276 struct resource *ports;
1278 if (devc->failed)
1280 printk(KERN_ERR "soundscape: Card not detected\n");
1281 return 0;
1283 if (devc->ok == 0)
1285 printk(KERN_ERR "soundscape: Invalid initialization order.\n");
1286 return 0;
1288 for (i = 0; i < 4; i++)
1290 if (hw_config->irq == valid_interrupts[i])
1292 irq_bits = i;
1293 break;
1296 if (irq_bits == 0xff) {
1297 printk(KERN_ERR "soundscape: Invalid MSS IRQ%d\n", hw_config->irq);
1298 return 0;
1301 if (old_hardware)
1302 ad_flags = 0x12345677; /* Tell that we may have a CS4248 chip (Spea-V7 Media FX) */
1303 else if (sscape_is_pnp)
1304 ad_flags = 0x87654321; /* Tell that we have a soundscape pnp with 1845 chip */
1306 ports = request_region(hw_config->io_base, 4, "ad1848");
1307 if (!ports) {
1308 printk(KERN_ERR "soundscape: ports busy\n");
1309 return 0;
1312 if (!ad1848_detect(ports, &ad_flags, hw_config->osp)) {
1313 release_region(hw_config->io_base, 4);
1314 return 0;
1317 if (!sscape_is_pnp) /*pnp is already setup*/
1320 * Setup the DMA polarity.
1322 sscape_write(devc, GA_DMACFG_REG, 0x50);
1325 * Take the gate-array off of the DMA channel.
1327 sscape_write(devc, GA_DMAB_REG, 0x20);
1330 * Init the AD1848 (CD-ROM) config reg.
1332 sscape_write(devc, GA_CDCFG_REG, 0x89 | (hw_config->dma << 4) | (irq_bits << 1));
1335 if (hw_config->irq == devc->irq)
1336 printk(KERN_WARNING "soundscape: Warning! The WSS mode can't share IRQ with MIDI\n");
1338 hw_config->slots[0] = ad1848_init(
1339 sscape_is_pnp ? "SoundScape" : "SoundScape PNP",
1340 ports,
1341 hw_config->irq,
1342 hw_config->dma,
1343 hw_config->dma,
1345 devc->osp,
1346 THIS_MODULE);
1349 if (hw_config->slots[0] != -1) /* The AD1848 driver installed itself */
1351 audio_devs[hw_config->slots[0]]->coproc = &sscape_coproc_operations;
1352 devc->codec_audiodev = hw_config->slots[0];
1353 devc->my_audiodev = hw_config->slots[0];
1355 /* Set proper routings here (what are they) */
1356 AD1848_REROUTE(SOUND_MIXER_LINE1, SOUND_MIXER_LINE);
1359 #ifdef SSCAPE_DEBUG5
1361 * Temporary debugging aid. Print contents of the registers
1362 * after the AD1848 device has been initialized.
1365 int i;
1367 for (i = 0; i < 13; i++)
1368 printk("I%d = %02x\n", i, sscape_read(devc, i));
1370 #endif
1371 return 1;
1374 static void __exit unload_sscape(struct address_info *hw_config)
1376 release_region(devc->base + 2, 6);
1377 unload_mpu401(hw_config);
1378 if (sscape_is_pnp)
1379 release_region(devc->codec, 2);
1382 static void __exit unload_ss_ms_sound(struct address_info *hw_config)
1384 ad1848_unload(hw_config->io_base,
1385 hw_config->irq,
1386 devc->dma,
1387 devc->dma,
1389 sound_unload_audiodev(hw_config->slots[0]);
1392 static struct address_info cfg;
1393 static struct address_info cfg_mpu;
1395 static int __initdata spea = -1;
1396 static int mss = 0;
1397 static int __initdata dma = -1;
1398 static int __initdata irq = -1;
1399 static int __initdata io = -1;
1400 static int __initdata mpu_irq = -1;
1401 static int __initdata mpu_io = -1;
1403 module_param(dma, int, 0);
1404 module_param(irq, int, 0);
1405 module_param(io, int, 0);
1406 module_param(spea, int, 0); /* spea=0/1 set the old_hardware */
1407 module_param(mpu_irq, int, 0);
1408 module_param(mpu_io, int, 0);
1409 module_param(mss, int, 0);
1411 static int __init init_sscape(void)
1413 printk(KERN_INFO "Soundscape driver Copyright (C) by Hannu Savolainen 1993-1996\n");
1415 cfg.irq = irq;
1416 cfg.dma = dma;
1417 cfg.io_base = io;
1419 cfg_mpu.irq = mpu_irq;
1420 cfg_mpu.io_base = mpu_io;
1421 /* WEH - Try to get right dma channel */
1422 cfg_mpu.dma = dma;
1424 devc->codec = cfg.io_base;
1425 devc->codec_irq = cfg.irq;
1426 devc->codec_type = 0;
1427 devc->ic_type = 0;
1428 devc->raw_buf = NULL;
1429 spin_lock_init(&devc->lock);
1431 if (cfg.dma == -1 || cfg.irq == -1 || cfg.io_base == -1) {
1432 printk(KERN_ERR "DMA, IRQ, and IO port must be specified.\n");
1433 return -EINVAL;
1436 if (cfg_mpu.irq == -1 && cfg_mpu.io_base != -1) {
1437 printk(KERN_ERR "MPU_IRQ must be specified if MPU_IO is set.\n");
1438 return -EINVAL;
1441 if(spea != -1) {
1442 old_hardware = spea;
1443 printk(KERN_INFO "Forcing %s hardware support.\n",
1444 spea?"new":"old");
1446 if (probe_sscape(&cfg_mpu) == 0)
1447 return -ENODEV;
1449 attach_sscape(&cfg_mpu);
1451 mss = init_ss_ms_sound(&cfg);
1453 return 0;
1456 static void __exit cleanup_sscape(void)
1458 if (mss)
1459 unload_ss_ms_sound(&cfg);
1460 unload_sscape(&cfg_mpu);
1463 module_init(init_sscape);
1464 module_exit(cleanup_sscape);
1466 #ifndef MODULE
1467 static int __init setup_sscape(char *str)
1469 /* io, irq, dma, mpu_io, mpu_irq */
1470 int ints[6];
1472 str = get_options(str, ARRAY_SIZE(ints), ints);
1474 io = ints[1];
1475 irq = ints[2];
1476 dma = ints[3];
1477 mpu_io = ints[4];
1478 mpu_irq = ints[5];
1480 return 1;
1483 __setup("sscape=", setup_sscape);
1484 #endif
1485 MODULE_LICENSE("GPL");