| blob | d9ff0e7a00f7c9c0c758ada596a40c23b76a89b2 |
1 iwpriv\r
2 =================\r
3 This is detailed explanation of each parameters for iwpriv.\r
4 Before reading this document, make sure you already read README.\r
5 \r
6 -------------------------------------------------------------------------------------------------------\r
7 USAGE:\r
8 iwpriv ra0 set [parameters]=[val]\r
9 \r
10 where\r
11 \r
12 [parameters] [val] range explaination\r
13 ----------------- ----------------------- ---------------------------------------------\r
14 CountryRegion {0~7} Set country region \r
15 0: use 1 ~ 11 Channel\r
16 1: use 1 ~ 11 Channel\r
17 2: use 1 ~ 13 Channel\r
18 3: use 10, 11 Channel\r
19 4: use 10 ~ 13 Channel\r
20 5: use 14 Channel\r
21 6: use 1 ~ 14 Channel\r
22 7: use 3 ~ 9 Channel\r
23 \r
24 SSID {0~z, less than 32 characters} Set SoftAP SSID\r
25 \r
26 WirelessMode {0~2} Set Wireless Mode \r
27 0:11b/g mixed, 1:11B only\r
28 \r
29 TxRate {0~12} Set TxRate \r
30 0:Auto, 1:1Mbps, 2:2Mbps, 3:5.5Mbps, 4:11Mbps, \r
31 5:6Mbps, 6:9Mbps, 7:12Mbps, 8:18Mbps, 9:24Mbps, \r
32 10:36Mbps, 11:48Mbps, 12:54Mbps\r
33 \r
34 Channel {1~14} depends on country region Set Channel\r
35 \r
36 BGProtection {0~2} Set 11B/11G Protection\r
37 0:Auto, 1:Always on, 2:Always off\r
38 \r
39 TxPreamble {0~2} Set TxPreamble\r
40 0:Preamble Long, 1:Preamble Short, 2:Auto\r
41 \r
42 RTSThreshold {1~2347} Set RTS Threshold \r
43 \r
44 FragThreshold {256~2346} Set Fragment Threshold\r
45 \r
46 TxBurst {0,1} Set TxBurst Enable or Disable\r
47 0:Disable, 1:Enable\r
48 \r
49 TurboRate {0,1} Set TurboRate Enable or Disable\r
50 0:Disable, 1:Enable\r
51 \r
52 AdhocModeRate {0, 1} Set Adhoc mode tx rate\r
53 0: adhere WIFI spec., 1: violate WIFI spec.\r
54 (802.11g WIFI spec disallow OFDM rates in 802.11g ADHOC mode)\r
55 \r
56 NetworkType {Infra,Adhoc} Set Network type\r
57 \r
58 AuthMode {OPEN,SHARED,WPAPSK} Set Authentication mode\r
59 \r
60 EncrypType {NONE,WEP,TKIP,AES} Set Encryption Type\r
61 \r
62 DefaultKeyID {1~4} Set Default Key ID\r
63 \r
64 Key1 {5 ascii characters or Set Key1 String\r
65 10 hex number or \r
66 13 ascii characters or \r
67 26 hex numbers} \r
68 \r
69 Key2 {5 ascii characters or Set Key2 String\r
70 10 hex number or \r
71 13 ascii characters or \r
72 26 hex numbers} \r
73 \r
74 Key3 {5 ascii characters or Set Key3 String\r
75 10 hex number or \r
76 13 ascii characters or \r
77 26 hex numbers} \r
78 \r
79 Key4 {5 ascii characters or Set Key4 String\r
80 10 hex number or \r
81 13 ascii characters or \r
82 26 hex numbers} \r
83 \r
84 \r
85 WPAPSK {8~63 ASCII or 64 HEX characters} WPA Pre-Shared Key \r
86 \r
87 ApClient {0,1} Set ApClient mode\r
88 0:Disable, 1:Enable\r
89 \r
90 \r
91 Examples\r
92 ===================================================================\r
93 -------------------------------------------------------------------------------------------------------\r
94 Example I: Config STA to link with AP which is OPEN/NONE(Authentication/Encryption)\r
95 1. iwpriv ra0 set NetworkType=Infra\r
96 2. iwpriv ra0 set AuthMode=OPEN\r
97 3. iwpriv ra0 set EncrypType=NONE\r
98 4. iwpriv ra0 set SSID="AP's SSID"\r
99 \r
100 Example II: Config STA to link with AP which is SHARED/WEP(Authentication/Encryption)\r
101 1. iwpriv ra0 set NetworkType=Infra\r
102 2. iwpriv ra0 set AuthMode=SHARED\r
103 3. iwpriv ra0 set EncrypType=WEP\r
104 4. iwpriv ra0 set Key1="AP's wep key"\r
105 5. iwpriv ra0 set DefaultKeyID=1\r
106 6. iwpriv ra0 set SSID="AP's SSID"\r
107 \r
108 Example III: Config STA to link with AP which is WPAPSK/TKIP(Authentication/Encryption)\r
109 1. iwpriv ra0 set NetworkType=Infra\r
110 2. iwpriv ra0 set AuthMode=WPAPSK\r
111 3. iwpriv ra0 set EncrypType=TKIP\r
112 4. iwpriv ra0 set SSID="AP's SSID"\r
113 5. iwpriv ra0 set WPAPSK="AP's wpa-preshared key"\r
114 6. iwpriv ra0 set SSID="AP's SSID"\r
115 \r
116 Example IV: Config STA to link with AP which is WPAPSK/AES(Authentication/Encryption)\r
117 1. iwpriv ra0 set NetworkType=Infra\r
118 2. iwpriv ra0 set AuthMode=WPAPSK\r
119 3. iwpriv ra0 set EncrypType=AES\r
120 4. iwpriv ra0 set SSID="AP's SSID"\r
121 5. iwpriv ra0 set WPAPSK="AP's wpa-preshared key"\r
122 6. iwpriv ra0 set SSID="AP's SSID"\r
123 \r
124 Example V: Config STA to create/link as adhoc mode\r
125 1. iwpriv ra0 set NetworkType=Adhoc\r
126 2. iwpriv ra0 set AuthMode=OPEN\r
127 3. iwpriv ra0 set EncrypType=NONE\r
128 4. iwpriv ra0 set SSID="Adhoc's SSID"\r
129 \r
130 \r
131 \r
132 iwlist\r
133 =================\r
134 This is detailed explanation of each parameters for iwlist.\r
135 \r
136 -------------------------------------------------------------------------------------------------------\r
137 \r
138 iwlist ra0 scanning ; list the result after scanning(site survey)\r
139 \r