firmware/drivers/tuner/si4700.c

   1 /***************************************************************************
   2  *             __________               __   ___.
   3  *   Open      \______   \ ____   ____ |  | _\_ |__   _______  ___
   4  *   Source     |       _//  _ \_/ ___\|  |/ /| __ \ /  _ \  \/  /
   5  *   Jukebox    |    |   (  <_> )  \___|    < | \_\ (  <_> > <  <
   6  *   Firmware   |____|_  /\____/ \___  >__|_ \|___  /\____/__/\_ \
   7  *                     \/            \/     \/    \/            \/
   8  * $Id$
   9  *
  10  * Tuner "middleware" for Silicon Labs SI4700 chip
  11  *
  12  * Copyright (C) 2008 Nils Wallménius
  13  *
  14  * This program is free software; you can redistribute it and/or
  15  * modify it under the terms of the GNU General Public License
  16  * as published by the Free Software Foundation; either version 2
  17  * of the License, or (at your option) any later version.
  18  *
  19  * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
  20  * KIND, either express or implied.
  21  *
  22  ****************************************************************************/
  23 #include "config.h"
  24 #include <stdbool.h>
  25 #include <string.h>
  26 #include <stdlib.h>
  27 #include "kernel.h"
  28 #include "power.h"
  29 #include "tuner.h" /* tuner abstraction interface */
  30 #include "fmradio.h"
  31 #include "fmradio_i2c.h" /* physical interface driver */
  32
  33 /* some models use the internal 32 kHz oscillator which needs special attention
  34    during initialisation, power-up and power-down.
  35 */
  36 #if defined(SANSA_CLIP) || defined(SANSA_E200V2) || defined(SANSA_FUZE) || defined(SANSA_C200V2)
  37 #define USE_INTERNAL_OSCILLATOR
  38 #elif defined(TOSHIBA_GIGABEAT_S)
  39 #define SI4700_GPIO_SETUP (SYSCONFIG1_GPIO1_HI_Z | \
  40                            SYSCONFIG1_GPIO2_HI_Z | \
  41                            SYSCONFIG1_GPIO3_MO_ST_I)
  42 extern int si4700_st(void);
  43 #endif
  44
  45 #ifndef SI4700_GPIO_SETUP
  46 #define SI4700_GPIO_SETUP 0
  47 #endif
  48
  49 #define SEEK_THRESHOLD 0x16
  50
  51 #define I2C_ADR 0x20
  52
  53 /** Registers and bits - "x" denotes Si4702/03 only (so they say) **/
  54 #define DEVICEID    0x0
  55 #define CHIPID      0x1
  56 #define POWERCFG    0x2
  57 #define CHANNEL     0x3
  58 #define SYSCONFIG1  0x4
  59 #define SYSCONFIG2  0x5
  60 #define SYSCONFIG3  0x6
  61 #define TEST1       0x7
  62 #define TEST2       0x8
  63 #define BOOTCONFIG  0x9
  64 #define STATUSRSSI  0xA
  65 #define READCHAN    0xB
  66 #define RDSA        0xC /* x */
  67 #define RDSB        0xD /* x */
  68 #define RDSC        0xE /* x */
  69 #define RDSD        0xF /* x */
  70
  71 /* DEVICEID (0x0) */
  72 #define DEVICEID_PN         (0xf << 12)
  73     /* 0x01 = Si4700/01 */
  74     /* 0x01 = Si4702/03 */
  75 #define DEVICEID_MFGID      (0xfff << 0)
  76     /* always 0x242 */
  77
  78 /* CHIPID (0x1) */
  79
  80 #if 0 /* Informational */
  81 /* Si4700/01 */
  82 #define CHIPID_REV          (0x3f << 10)
  83 #define CHIPID_DEV          (0x1 << 9)
  84     /* 0 before powerup */
  85     /* 0 after powerup = Si4700 */
  86     /* 1 after powerup = Si4701 */
  87 #define CHIPID_FIRMWARE     (0xff << 0)
  88
  89 /* Si4702/03 */
  90 #define CHIPID_REV          (0x3f << 10)
  91 #define CHIPID_DEV          (0xf << 6)
  92     /* 0000 before PU = Si4702 */
  93     /* 0001 after PU = Si4702 */
  94     /* 1000 before PU = Si4703 */
  95     /* 1001 after PU = Si4703 */
  96 #define CHIPID_FIRMWARE     (0x3f << 0)
  97 #endif /* 0 */
  98
  99 /* POWERCFG (0x2) */
 100 #define POWERCFG_DSMUTE     (0x1 << 15)
 101 #define POWERCFG_DMUTE      (0x1 << 14)
 102 #define POWERCFG_MONO       (0x1 << 13)
 103 #define POWERCFG_RDSM       (0x1 << 11) /* x */
 104 #define POWERCFG_SKMODE     (0x1 << 10)
 105 #define POWERCFG_SEEKUP     (0x1 <<  9)
 106 #define POWERCFG_SEEK       (0x1 <<  8)
 107 #define POWERCFG_DISABLE    (0x1 <<  6)
 108 #define POWERCFG_ENABLE     (0x1 <<  0)
 109
 110 /* CHANNEL (0x3) */
 111 #define CHANNEL_TUNE        (0x1 << 15)
 112 #define CHANNEL_CHAN        (0x3ff << 0)
 113     #define CHANNEL_CHANw(x) ((x) & CHANNEL_CHAN)
 114
 115 /* SYSCONFIG1 (0x4) */
 116 #define SYSCONFIG1_RDSIEN   (0x1 << 15) /* x */
 117 #define SYSCONFIG1_STCIEN   (0x1 << 14)
 118 #define SYSCONFIG1_RDS      (0x1 << 12) /* x */
 119 #define SYSCONFIG1_DE       (0x1 << 11)
 120 #define SYSCONFIG1_AGCD     (0x1 << 10)
 121 #define SYSCONFIG1_BLNDADJ  (0x3 <<  6)
 122     #define SYSCONFIG1_BLNDADJ_31_39_RSSI (0x0 << 6)
 123     #define SYSCONFIG1_BLNDADJ_37_55_RSSI (0x1 << 6)
 124     #define SYSCONFIG1_BLNDADJ_19_37_RSSI (0x2 << 6)
 125     #define SYSCONFIG1_BLNDADJ_25_43_RSSI (0x3 << 6)
 126 #define SYSCONFIG1_GPIO3    (0x3 <<  4)
 127     #define SYSCONFIG1_GPIO3_HI_Z       (0x0 << 4)
 128     #define SYSCONFIG1_GPIO3_MO_ST_I    (0x1 << 4)
 129     #define SYSCONFIG1_GPIO3_LOW        (0x2 << 4)
 130     #define SYSCONFIG1_GPIO3_HI         (0x3 << 4)
 131 #define SYSCONFIG1_GPIO2    (0x3 <<  2)
 132     #define SYSCONFIG1_GPIO2_HI_Z       (0x0 << 2)
 133     #define SYSCONFIG1_GPIO2_STC_RDS_I  (0x1 << 2)
 134     #define SYSCONFIG1_GPIO2_LOW        (0x2 << 2)
 135     #define SYSCONFIG1_GPIO2_HI         (0x3 << 2)
 136 #define SYSCONFIG1_GPIO1    (0x3 <<  0)
 137     #define SYSCONFIG1_GPIO1_HI_Z       (0x0 << 0)
 138     #define SYSCONFIG1_GPIO1_LOW        (0x2 << 0)
 139     #define SYSCONFIG1_GPIO1_HI         (0x3 << 0)
 140
 141 /* SYSCONFIG2 (0x5) */
 142 #define SYSCONFIG2_SEEKTH   (0xff << 8)
 143     #define SYSCONFIG2_SKEETHw(x) (((x) << 8) & SYSCONFIG2_SEEKTH)
 144 #define SYSCONFIG2_BAND     (0x3 << 6)
 145     #define SYSCONFIG2_BANDw(x)   (((x) << 6) & SYSCONFIG2_BAND)
 146     #define SYSCONFIG2_BANDr(x)   (((x) & SYSCONFIG2_BAND) >> 6)
 147     #define SYSCONFIG2_BAND_875_1080    (0x0 << 6) /* tenth-megahertz */
 148     #define SYSCONFIG2_BAND_760_1080    (0x1 << 6)
 149     #define SYSCONFIG2_BAND_760_900     (0x2 << 6)
 150 #define SYSCONFIG2_SPACE    (0x3 << 4)
 151     #define SYSCONFIG2_SPACEw(x)  (((x) << 4) & SYSCONFIG2_SPACE)
 152     #define SYSCONFIG2_SPACEr(x)  (((x) & SYSCONFIG2_SPACE) >> 4)
 153     #define SYSCONFIG2_SPACE_200KHZ     (0x0 << 4)
 154     #define SYSCONFIG2_SPACE_100KHZ     (0x1 << 4)
 155     #define SYSCONFIG2_SPACE_50KHZ      (0x2 << 4)
 156 /* 4700/01            0000=mute,0001=-28dBFS..2dB steps..1111= +0dBFS */
 157 /* 4702/03: VOLEXT=0: 0000=mute,0001=-28dBFS..2dB steps..1111= +0dBFS */
 158 /*          VOLEXT=1: 0000=mute,0001=-58dBFS..2dB steps..1111=-30dBFS */
 159 #define SYSCONFIG2_VOLUME   (0xf << 0)
 160     #define SYSCONFIG2_VOLUMEw(x) ((x) & SYSCONFIG2_VOLUME)
 161
 162 /* SYSCONFIG3 (0x6) */
 163 #define SYSCONFIG3_SMUTER   (0x3 << 14)
 164     #define SYSCONFIG3_SMUTER_FASTEST   (0x0 << 14)
 165     #define SYSCONFIG3_SMUTER_FAST      (0x1 << 14)
 166     #define SYSCONFIG3_SMUTER_SLOW      (0x2 << 14)
 167     #define SYSCONFIG3_SMUTER_SLOWEST   (0x3 << 14)
 168 #define SYSCONFIG3_SMUTEA   (0x3 << 12)
 169     #define SYSCONFIG3_SMUTEA_16DB      (0x0 << 12)
 170     #define SYSCONFIG3_SMUTEA_14DB      (0x1 << 12)
 171     #define SYSCONFIG3_SMUTEA_12DB      (0x2 << 12)
 172     #define SYSCONFIG3_SMUTEA_10DB      (0x3 << 12)
 173 #define SYSCONFIG3_VOLEXT   (0x1 << 8) /* x */
 174 #define SYSCONFIG3_SKSNR    (0xf << 4)
 175     #define SYSCONFIG3_SKSNRw(x) (((x) << 4) & SYSCONFIG3_SKSNR)
 176 #define SYSCONFIG3_SKCNT    (0xf << 0)
 177     #define SYSCONFIG3_SKCNTw(x) (((x) << 0) & SYSCONFIG3_SKCNT)
 178
 179 /* TEST1 (0x7) */
 180 /* 4700/01: 15=always 0, 13:0 = write with preexisting values! */
 181 /* 4702/03:              13:0 = write with preexisting values! */
 182 #define TEST1_XOSCEN        (0x1 << 15) /* x */
 183 #define TEST1_AHIZEN        (0x1 << 14)
 184
 185 /* TEST2 (0x8) */
 186 /* 15:0 = write with preexisting values! */
 187
 188 /* BOOTCONFIG (0x9) */
 189 /* 15:0 = write with preexisting values! */
 190
 191 /* STATUSRSSI (0xA) */
 192 #define STATUSRSSI_RDSR     (0x1 << 15) /* x */
 193 #define STATUSRSSI_STC      (0x1 << 14)
 194 #define STATUSRSSI_SFBL     (0x1 << 13)
 195 #define STATUSRSSI_AFCRL    (0x1 << 12)
 196 #define STATUSRSSI_RDSS     (0x1 << 11) /* x */
 197 #define STATUSRSSI_BLERA    (0x3 <<  9) /* x */
 198 #define STATUSRSSI_ST       (0x1 <<  8)
 199 #define STATUSRSSI_RSSI     (0xff << 0)
 200     #define STATUSRSSI_RSSIr(x) ((x) & 0xff)
 201
 202 /* READCHAN (0xB) */
 203 #define READCHAN_BLERB      (0x3 << 14) /* x */
 204 #define READCHAN_BLERC      (0x3 << 12) /* x */
 205 #define READCHAN_BLERD      (0x3 << 10) /* x */
 206 #define READCHAN_READCHAN   (0x3ff << 0)
 207
 208 /* RDSA-D (0xC-0xF) */
 209 /* 4702/03: RDS Block A-D data */
 210
 211 static bool tuner_present = false;
 212 static int curr_frequency = 87500000; /* Current station frequency (HZ) */
 213 static uint16_t cache[16];
 214
 215 /* reads <len> registers from radio at offset 0x0A into cache */
 216 static void si4700_read(int len)
 217 {
 218     int i;
 219     unsigned char buf[32];
 220     unsigned char *ptr = buf;
 221     uint16_t data;
 222
 223     fmradio_i2c_read(I2C_ADR, buf, len * 2);
 224     for (i = 0; i < len; i++) {
 225         data = ptr[0] << 8 | ptr[1];
 226         cache[(i + STATUSRSSI) & 0xF] = data;
 227         ptr += 2;
 228     }
 229 }
 230
 231 /* writes <len> registers from cache to radio at offset 0x02 */
 232 static void si4700_write(int len)
 233 {
 234     int i;
 235     unsigned char buf[32];
 236     unsigned char *ptr = buf;
 237     uint16_t data;
 238
 239     for (i = 0; i < len; i++) {
 240         data = cache[(i + POWERCFG) & 0xF];
 241         *ptr++ = (data >> 8) & 0xFF;
 242         *ptr++ = data & 0xFF;
 243     }
 244     fmradio_i2c_write(I2C_ADR, buf, len * 2);
 245 }
 246
 247 /* Hide silly, wrapped and continuous register reading and make interface
 248  * appear sane and normal. This also makes the driver compatible with
 249  * using the 3-wire interface. */
 250 static uint16_t si4700_read_reg(int reg)
 251 {
 252     si4700_read(((reg - STATUSRSSI) & 0xF) + 1);
 253     return cache[reg];
 254 }
 255
 256 static void si4700_write_reg(int reg, uint16_t value)
 257 {
 258     cache[reg] = value;
 259     si4700_write(((reg - POWERCFG) & 0xF) + 1);
 260 }
 261
 262 static void si4700_write_masked(int reg, uint16_t bits, uint16_t mask)
 263 {
 264     si4700_write_reg(reg, (cache[reg] & ~mask) | (bits & mask));
 265 }
 266
 267 static void si4700_write_set(int reg, uint16_t mask)
 268 {
 269     si4700_write_reg(reg, cache[reg] | mask);
 270 }
 271
 272 static void si4700_write_clear(int reg, uint16_t mask)
 273 {
 274     si4700_write_reg(reg, cache[reg] & ~mask);
 275 }
 276
 277 #if (SI4700_GPIO_SETUP & SYSCONFIG1_GPIO3) != SYSCONFIG1_GPIO3_MO_ST_I
 278 /* Poll i2c for the stereo status */
 279 static inline int si4700_st(void)
 280 {
 281     return (si4700_read_reg(STATUSRSSI) & STATUSRSSI_ST) >> 8;
 282 }
 283 #endif
 284
 285 static void si4700_sleep(int snooze)
 286 {
 287     if (snooze)
 288     {
 289         /** power down **/
 290         /* ENABLE high, DISABLE high */
 291         si4700_write_set(POWERCFG,
 292                          POWERCFG_DISABLE | POWERCFG_ENABLE);
 293         /* Bits self-clear once placed in powerdown. */
 294         cache[POWERCFG] &= ~(POWERCFG_DISABLE | POWERCFG_ENABLE);
 295     }
 296     else
 297     {
 298         /** power up **/
 299         /* ENABLE high, DISABLE low */
 300         si4700_write_masked(POWERCFG, POWERCFG_ENABLE,
 301                             POWERCFG_DISABLE | POWERCFG_ENABLE);
 302         sleep(110 * HZ / 1000);
 303
 304         /* init register cache */
 305         si4700_read(16);
 306
 307 #if SI4700_GPIO_SETUP != 0
 308         si4700_write_masked(SYSCONFIG1, SI4700_GPIO_SETUP,
 309                             SYSCONFIG1_GPIO1 | SYSCONFIG1_GPIO2 |
 310                             SYSCONFIG1_GPIO3);
 311 #endif
 312         si4700_write_masked(SYSCONFIG2,
 313                             SYSCONFIG2_SKEETHw(SEEK_THRESHOLD) |
 314                             SYSCONFIG2_VOLUMEw(0xF),
 315                             SYSCONFIG2_VOLUME | SYSCONFIG2_SEEKTH);
 316     }
 317 }
 318
 319 void si4700_init(void)
 320 {
 321     tuner_power(true);
 322
 323     /* read all registers */
 324     si4700_read(16);
 325     si4700_sleep(0);
 326
 327     /* check device id */
 328     if (cache[DEVICEID] == 0x1242)
 329     {
 330         tuner_present = true;
 331
 332 #ifdef USE_INTERNAL_OSCILLATOR
 333         /* Enable the internal oscillator
 334           (Si4702-16 needs this register to be initialised to 0x100) */
 335         si4700_write_set(TEST1, TEST1_XOSCEN | 0x100);
 336         sleep(HZ/2);
 337 #endif
 338     }
 339
 340     si4700_sleep(1);
 341
 342     tuner_power(false);
 343 }
 344
 345 static void si4700_set_frequency(int freq)
 346 {
 347     static const unsigned int spacings[3] =
 348     {
 349           200000, /* SYSCONFIG2_SPACE_200KHZ */
 350           100000, /* SYSCONFIG2_SPACE_100KHZ */
 351            50000, /* SYSCONFIG2_SPACE_50KHZ  */
 352     };
 353     static const unsigned int bands[3] =
 354     {
 355         87500000, /* SYSCONFIG2_BAND_875_1080 */
 356         76000000, /* SYSCONFIG2_BAND_760_1080 */
 357         76000000, /* SYSCONFIG2_BAND_760_900  */
 358     };
 359
 360     /* check BAND and spacings */
 361     int space = SYSCONFIG2_SPACEr(cache[SYSCONFIG2]);
 362     int band = SYSCONFIG2_BANDr(cache[SYSCONFIG2]);
 363     int chan = (freq - bands[band]) / spacings[space];
 364
 365     curr_frequency = freq;
 366
 367     si4700_write_reg(CHANNEL, CHANNEL_CHANw(chan) | CHANNEL_TUNE);
 368
 369     do
 370     {
 371         /* tuning should be done within 60 ms according to the datasheet */
 372         sleep(HZ * 60 / 1000);
 373     }
 374     while ((si4700_read_reg(STATUSRSSI) & STATUSRSSI_STC) == 0); /* STC high? */
 375
 376     si4700_write_clear(CHANNEL, CHANNEL_TUNE); /* Set TUNE low */
 377 }
 378
 379 static int si4700_tuned(void)
 380 {
 381     /* Primitive tuning check: sufficient level and AFC not railed */
 382     uint16_t status = si4700_read_reg(STATUSRSSI);
 383     if (STATUSRSSI_RSSIr(status) >= SEEK_THRESHOLD &&
 384         (status & STATUSRSSI_AFCRL) == 0)
 385         return 1;
 386
 387     return 0;
 388 }
 389
 390 static void si4700_set_region(int region)
 391 {
 392     const struct si4700_region_data *rd = &si4700_region_data[region];
 393     uint16_t bandspacing = SYSCONFIG2_BANDw(rd->band) |
 394                            SYSCONFIG2_SPACEw(rd->spacing);
 395     uint16_t oldbs = cache[SYSCONFIG2] & (SYSCONFIG2_BAND | SYSCONFIG2_SPACE);
 396
 397     si4700_write_masked(SYSCONFIG1,
 398                         rd->deemphasis ? SYSCONFIG1_DE : 0,
 399                         SYSCONFIG1_DE);
 400     si4700_write_masked(SYSCONFIG2, bandspacing,
 401                         SYSCONFIG2_BAND | SYSCONFIG2_SPACE);
 402
 403     /* Retune if this region change would change the channel number. */
 404     if (oldbs != bandspacing)
 405         si4700_set_frequency(curr_frequency);
 406 }
 407
 408 /* tuner abstraction layer: set something to the tuner */
 409 int si4700_set(int setting, int value)
 410 {
 411     switch(setting)
 412     {
 413         case RADIO_SLEEP:
 414             si4700_sleep(value);
 415             break;
 416
 417         case RADIO_FREQUENCY:
 418             si4700_set_frequency(value);
 419             break;
 420
 421         case RADIO_SCAN_FREQUENCY:
 422             si4700_set_frequency(value);
 423             return si4700_tuned();
 424
 425         case RADIO_MUTE:
 426             si4700_write_masked(POWERCFG, value ? 0 : POWERCFG_DMUTE,
 427                                 POWERCFG_DMUTE);
 428             break;
 429
 430         case RADIO_REGION:
 431             si4700_set_region(value);
 432             break;
 433
 434         case RADIO_FORCE_MONO:
 435             si4700_write_masked(POWERCFG, value ? POWERCFG_MONO : 0,
 436                                 POWERCFG_MONO);
 437             break;
 438
 439         default:
 440             return -1;
 441     }
 442
 443     return 1;
 444 }
 445
 446 /* tuner abstraction layer: read something from the tuner */
 447 int si4700_get(int setting)
 448 {
 449     int val = -1; /* default for unsupported query */
 450
 451     switch(setting)
 452     {
 453         case RADIO_PRESENT:
 454             val = tuner_present ? 1 : 0;
 455             break;
 456
 457         case RADIO_TUNED:
 458             val = si4700_tuned();
 459             break;
 460
 461         case RADIO_STEREO:
 462             val = si4700_st();
 463             break;
 464     }
 465
 466     return val;
 467 }
 468
 469 void si4700_dbg_info(struct si4700_dbg_info *nfo)
 470 {
 471     memset(nfo->regs, 0, sizeof (nfo->regs));
 472
 473     if (tuner_powered())
 474     {
 475         si4700_read(16);
 476         memcpy(nfo->regs, cache, sizeof (nfo->regs));
 477     }
 478 }
 479