From 2187f287e2827556210e96c619f76f0f9dd928f0 Mon Sep 17 00:00:00 2001 From: Thomas Bogendoerfer Date: Thu, 28 Jun 2007 00:46:22 +0200 Subject: [PATCH] Extract chip specific code out of lasi_82596.c Changes to last version: - use netdev_alloc_skb - make init_rx_bufs just fail and not panic, if skb alloc fails - don/t free_irq, if request_irq failed Thomas. Extracted chip specific code out of lasi_82596.c and placed into a lib82596.c to make it usable for other 82596 drivers Signed-off-by: Thomas Bogendoerfer Signed-off-by: Jeff Garzik --- drivers/net/lasi_82596.c | 1840 ++++++---------------------------------------- drivers/net/lib82596.c | 1434 ++++++++++++++++++++++++++++++++++++ 2 files changed, 1673 insertions(+), 1601 deletions(-) rewrite drivers/net/lasi_82596.c (88%) create mode 100644 drivers/net/lib82596.c diff --git a/drivers/net/lasi_82596.c b/drivers/net/lasi_82596.c dissimilarity index 88% index 741780e14b2..efbae4b8398 100644 --- a/drivers/net/lasi_82596.c +++ b/drivers/net/lasi_82596.c @@ -1,1601 +1,239 @@ -/* lasi_82596.c -- driver for the intel 82596 ethernet controller, as - munged into HPPA boxen . - - This driver is based upon 82596.c, original credits are below... - but there were too many hoops which HP wants jumped through to - keep this code in there in a sane manner. - - 3 primary sources of the mess -- - 1) hppa needs *lots* of cacheline flushing to keep this kind of - MMIO running. - - 2) The 82596 needs to see all of its pointers as their physical - address. Thus virt_to_bus/bus_to_virt are *everywhere*. - - 3) The implementation HP is using seems to be significantly pickier - about when and how the command and RX units are started. some - command ordering was changed. - - Examination of the mach driver leads one to believe that there - might be a saner way to pull this off... anyone who feels like a - full rewrite can be my guest. - - Split 02/13/2000 Sam Creasey (sammy@oh.verio.com) - - 02/01/2000 Initial modifications for parisc by Helge Deller (deller@gmx.de) - 03/02/2000 changes for better/correct(?) cache-flushing (deller) -*/ - -/* 82596.c: A generic 82596 ethernet driver for linux. */ -/* - Based on Apricot.c - Written 1994 by Mark Evans. - This driver is for the Apricot 82596 bus-master interface - - Modularised 12/94 Mark Evans - - - Modified to support the 82596 ethernet chips on 680x0 VME boards. - by Richard Hirst - Renamed to be 82596.c - - 980825: Changed to receive directly in to sk_buffs which are - allocated at open() time. Eliminates copy on incoming frames - (small ones are still copied). Shared data now held in a - non-cached page, so we can run on 68060 in copyback mode. - - TBD: - * look at deferring rx frames rather than discarding (as per tulip) - * handle tx ring full as per tulip - * performace test to tune rx_copybreak - - Most of my modifications relate to the braindead big-endian - implementation by Intel. When the i596 is operating in - 'big-endian' mode, it thinks a 32 bit value of 0x12345678 - should be stored as 0x56781234. This is a real pain, when - you have linked lists which are shared by the 680x0 and the - i596. - - Driver skeleton - Written 1993 by Donald Becker. - Copyright 1993 United States Government as represented by the Director, - National Security Agency. This software may only be used and distributed - according to the terms of the GNU General Public License as modified by SRC, - incorporated herein by reference. - - The author may be reached as becker@scyld.com, or C/O - Scyld Computing Corporation, 410 Severn Ave., Suite 210, Annapolis MD 21403 - - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include -#include -#include - -#define LASI_82596_DRIVER_VERSION "LASI 82596 driver - Revision: 1.30" - -/* DEBUG flags - */ - -#define DEB_INIT 0x0001 -#define DEB_PROBE 0x0002 -#define DEB_SERIOUS 0x0004 -#define DEB_ERRORS 0x0008 -#define DEB_MULTI 0x0010 -#define DEB_TDR 0x0020 -#define DEB_OPEN 0x0040 -#define DEB_RESET 0x0080 -#define DEB_ADDCMD 0x0100 -#define DEB_STATUS 0x0200 -#define DEB_STARTTX 0x0400 -#define DEB_RXADDR 0x0800 -#define DEB_TXADDR 0x1000 -#define DEB_RXFRAME 0x2000 -#define DEB_INTS 0x4000 -#define DEB_STRUCT 0x8000 -#define DEB_ANY 0xffff - - -#define DEB(x,y) if (i596_debug & (x)) { y; } - - -#define CHECK_WBACK(priv, addr,len) \ - do { dma_cache_sync((priv)->dev, (void *)addr, len, DMA_TO_DEVICE); } while (0) - -#define CHECK_INV(priv, addr,len) \ - do { dma_cache_sync((priv)->dev, (void *)addr, len, DMA_FROM_DEVICE); } while(0) - -#define CHECK_WBACK_INV(priv, addr,len) \ - do { dma_cache_sync((priv)->dev, (void *)addr, len, DMA_BIDIRECTIONAL); } while (0) - - -#define PA_I82596_RESET 0 /* Offsets relative to LASI-LAN-Addr.*/ -#define PA_CPU_PORT_L_ACCESS 4 -#define PA_CHANNEL_ATTENTION 8 - - -/* - * Define various macros for Channel Attention, word swapping etc., dependent - * on architecture. MVME and BVME are 680x0 based, otherwise it is Intel. - */ - -#ifdef __BIG_ENDIAN -#define WSWAPrfd(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define WSWAPrbd(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define WSWAPiscp(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define WSWAPscb(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define WSWAPcmd(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define WSWAPtbd(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define WSWAPchar(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define ISCP_BUSY 0x00010000 -#define MACH_IS_APRICOT 0 -#else -#define WSWAPrfd(x) ((struct i596_rfd *)(x)) -#define WSWAPrbd(x) ((struct i596_rbd *)(x)) -#define WSWAPiscp(x) ((struct i596_iscp *)(x)) -#define WSWAPscb(x) ((struct i596_scb *)(x)) -#define WSWAPcmd(x) ((struct i596_cmd *)(x)) -#define WSWAPtbd(x) ((struct i596_tbd *)(x)) -#define WSWAPchar(x) ((char *)(x)) -#define ISCP_BUSY 0x0001 -#define MACH_IS_APRICOT 1 -#endif - -/* - * The MPU_PORT command allows direct access to the 82596. With PORT access - * the following commands are available (p5-18). The 32-bit port command - * must be word-swapped with the most significant word written first. - * This only applies to VME boards. - */ -#define PORT_RESET 0x00 /* reset 82596 */ -#define PORT_SELFTEST 0x01 /* selftest */ -#define PORT_ALTSCP 0x02 /* alternate SCB address */ -#define PORT_ALTDUMP 0x03 /* Alternate DUMP address */ - -static int i596_debug = (DEB_SERIOUS|DEB_PROBE); - -MODULE_AUTHOR("Richard Hirst"); -MODULE_DESCRIPTION("i82596 driver"); -MODULE_LICENSE("GPL"); -module_param(i596_debug, int, 0); -MODULE_PARM_DESC(i596_debug, "lasi_82596 debug mask"); - -/* Copy frames shorter than rx_copybreak, otherwise pass on up in - * a full sized sk_buff. Value of 100 stolen from tulip.c (!alpha). - */ -static int rx_copybreak = 100; - -#define MAX_DRIVERS 4 /* max count of drivers */ - -#define PKT_BUF_SZ 1536 -#define MAX_MC_CNT 64 - -#define I596_NULL ((u32)0xffffffff) - -#define CMD_EOL 0x8000 /* The last command of the list, stop. */ -#define CMD_SUSP 0x4000 /* Suspend after doing cmd. */ -#define CMD_INTR 0x2000 /* Interrupt after doing cmd. */ - -#define CMD_FLEX 0x0008 /* Enable flexible memory model */ - -enum commands { - CmdNOp = 0, CmdSASetup = 1, CmdConfigure = 2, CmdMulticastList = 3, - CmdTx = 4, CmdTDR = 5, CmdDump = 6, CmdDiagnose = 7 -}; - -#define STAT_C 0x8000 /* Set to 0 after execution */ -#define STAT_B 0x4000 /* Command being executed */ -#define STAT_OK 0x2000 /* Command executed ok */ -#define STAT_A 0x1000 /* Command aborted */ - -#define CUC_START 0x0100 -#define CUC_RESUME 0x0200 -#define CUC_SUSPEND 0x0300 -#define CUC_ABORT 0x0400 -#define RX_START 0x0010 -#define RX_RESUME 0x0020 -#define RX_SUSPEND 0x0030 -#define RX_ABORT 0x0040 - -#define TX_TIMEOUT 5 - -#define OPT_SWAP_PORT 0x0001 /* Need to wordswp on the MPU port */ - - -struct i596_reg { - unsigned short porthi; - unsigned short portlo; - u32 ca; -}; - -#define EOF 0x8000 -#define SIZE_MASK 0x3fff - -struct i596_tbd { - unsigned short size; - unsigned short pad; - dma_addr_t next; - dma_addr_t data; - u32 cache_pad[5]; /* Total 32 bytes... */ -}; - -/* The command structure has two 'next' pointers; v_next is the address of - * the next command as seen by the CPU, b_next is the address of the next - * command as seen by the 82596. The b_next pointer, as used by the 82596 - * always references the status field of the next command, rather than the - * v_next field, because the 82596 is unaware of v_next. It may seem more - * logical to put v_next at the end of the structure, but we cannot do that - * because the 82596 expects other fields to be there, depending on command - * type. - */ - -struct i596_cmd { - struct i596_cmd *v_next; /* Address from CPUs viewpoint */ - unsigned short status; - unsigned short command; - dma_addr_t b_next; /* Address from i596 viewpoint */ -}; - -struct tx_cmd { - struct i596_cmd cmd; - dma_addr_t tbd; - unsigned short size; - unsigned short pad; - struct sk_buff *skb; /* So we can free it after tx */ - dma_addr_t dma_addr; -#ifdef __LP64__ - u32 cache_pad[6]; /* Total 64 bytes... */ -#else - u32 cache_pad[1]; /* Total 32 bytes... */ -#endif -}; - -struct tdr_cmd { - struct i596_cmd cmd; - unsigned short status; - unsigned short pad; -}; - -struct mc_cmd { - struct i596_cmd cmd; - short mc_cnt; - char mc_addrs[MAX_MC_CNT*6]; -}; - -struct sa_cmd { - struct i596_cmd cmd; - char eth_addr[8]; -}; - -struct cf_cmd { - struct i596_cmd cmd; - char i596_config[16]; -}; - -struct i596_rfd { - unsigned short stat; - unsigned short cmd; - dma_addr_t b_next; /* Address from i596 viewpoint */ - dma_addr_t rbd; - unsigned short count; - unsigned short size; - struct i596_rfd *v_next; /* Address from CPUs viewpoint */ - struct i596_rfd *v_prev; -#ifndef __LP64__ - u32 cache_pad[2]; /* Total 32 bytes... */ -#endif -}; - -struct i596_rbd { - /* hardware data */ - unsigned short count; - unsigned short zero1; - dma_addr_t b_next; - dma_addr_t b_data; /* Address from i596 viewpoint */ - unsigned short size; - unsigned short zero2; - /* driver data */ - struct sk_buff *skb; - struct i596_rbd *v_next; - dma_addr_t b_addr; /* This rbd addr from i596 view */ - unsigned char *v_data; /* Address from CPUs viewpoint */ - /* Total 32 bytes... */ -#ifdef __LP64__ - u32 cache_pad[4]; -#endif -}; - -/* These values as chosen so struct i596_private fits in one page... */ - -#define TX_RING_SIZE 32 -#define RX_RING_SIZE 16 - -struct i596_scb { - unsigned short status; - unsigned short command; - dma_addr_t cmd; - dma_addr_t rfd; - u32 crc_err; - u32 align_err; - u32 resource_err; - u32 over_err; - u32 rcvdt_err; - u32 short_err; - unsigned short t_on; - unsigned short t_off; -}; - -struct i596_iscp { - u32 stat; - dma_addr_t scb; -}; - -struct i596_scp { - u32 sysbus; - u32 pad; - dma_addr_t iscp; -}; - -struct i596_private { - volatile struct i596_scp scp __attribute__((aligned(32))); - volatile struct i596_iscp iscp __attribute__((aligned(32))); - volatile struct i596_scb scb __attribute__((aligned(32))); - struct sa_cmd sa_cmd __attribute__((aligned(32))); - struct cf_cmd cf_cmd __attribute__((aligned(32))); - struct tdr_cmd tdr_cmd __attribute__((aligned(32))); - struct mc_cmd mc_cmd __attribute__((aligned(32))); - struct i596_rfd rfds[RX_RING_SIZE] __attribute__((aligned(32))); - struct i596_rbd rbds[RX_RING_SIZE] __attribute__((aligned(32))); - struct tx_cmd tx_cmds[TX_RING_SIZE] __attribute__((aligned(32))); - struct i596_tbd tbds[TX_RING_SIZE] __attribute__((aligned(32))); - u32 stat; - int last_restart; - struct i596_rfd *rfd_head; - struct i596_rbd *rbd_head; - struct i596_cmd *cmd_tail; - struct i596_cmd *cmd_head; - int cmd_backlog; - u32 last_cmd; - struct net_device_stats stats; - int next_tx_cmd; - int options; - spinlock_t lock; - dma_addr_t dma_addr; - struct device *dev; -}; - -static const char init_setup[] = -{ - 0x8E, /* length, prefetch on */ - 0xC8, /* fifo to 8, monitor off */ - 0x80, /* don't save bad frames */ - 0x2E, /* No source address insertion, 8 byte preamble */ - 0x00, /* priority and backoff defaults */ - 0x60, /* interframe spacing */ - 0x00, /* slot time LSB */ - 0xf2, /* slot time and retries */ - 0x00, /* promiscuous mode */ - 0x00, /* collision detect */ - 0x40, /* minimum frame length */ - 0xff, - 0x00, - 0x7f /* *multi IA */ }; - -static int i596_open(struct net_device *dev); -static int i596_start_xmit(struct sk_buff *skb, struct net_device *dev); -static irqreturn_t i596_interrupt(int irq, void *dev_id); -static int i596_close(struct net_device *dev); -static struct net_device_stats *i596_get_stats(struct net_device *dev); -static void i596_add_cmd(struct net_device *dev, struct i596_cmd *cmd); -static void i596_tx_timeout (struct net_device *dev); -static void print_eth(unsigned char *buf, char *str); -static void set_multicast_list(struct net_device *dev); - -static int rx_ring_size = RX_RING_SIZE; -static int ticks_limit = 100; -static int max_cmd_backlog = TX_RING_SIZE-1; - -#ifdef CONFIG_NET_POLL_CONTROLLER -static void i596_poll_controller(struct net_device *dev); -#endif - - -static inline void CA(struct net_device *dev) -{ - gsc_writel(0, dev->base_addr + PA_CHANNEL_ATTENTION); -} - - -static inline void MPU_PORT(struct net_device *dev, int c, dma_addr_t x) -{ - struct i596_private *lp = dev->priv; - - u32 v = (u32) (c) | (u32) (x); - u16 a, b; - - if (lp->options & OPT_SWAP_PORT) { - a = v >> 16; - b = v & 0xffff; - } else { - a = v & 0xffff; - b = v >> 16; - } - - gsc_writel(a, dev->base_addr + PA_CPU_PORT_L_ACCESS); - udelay(1); - gsc_writel(b, dev->base_addr + PA_CPU_PORT_L_ACCESS); -} - - -static inline int wait_istat(struct net_device *dev, struct i596_private *lp, int delcnt, char *str) -{ - CHECK_INV(lp, &(lp->iscp), sizeof(struct i596_iscp)); - while (--delcnt && lp->iscp.stat) { - udelay(10); - CHECK_INV(lp, &(lp->iscp), sizeof(struct i596_iscp)); - } - if (!delcnt) { - printk("%s: %s, iscp.stat %04x, didn't clear\n", - dev->name, str, lp->iscp.stat); - return -1; - } - else - return 0; -} - - -static inline int wait_cmd(struct net_device *dev, struct i596_private *lp, int delcnt, char *str) -{ - CHECK_INV(lp, &(lp->scb), sizeof(struct i596_scb)); - while (--delcnt && lp->scb.command) { - udelay(10); - CHECK_INV(lp, &(lp->scb), sizeof(struct i596_scb)); - } - if (!delcnt) { - printk("%s: %s, status %4.4x, cmd %4.4x.\n", - dev->name, str, lp->scb.status, lp->scb.command); - return -1; - } - else - return 0; -} - - -static void i596_display_data(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - struct i596_cmd *cmd; - struct i596_rfd *rfd; - struct i596_rbd *rbd; - - printk("lp and scp at %p, .sysbus = %08x, .iscp = %08x\n", - &lp->scp, lp->scp.sysbus, lp->scp.iscp); - printk("iscp at %p, iscp.stat = %08x, .scb = %08x\n", - &lp->iscp, lp->iscp.stat, lp->iscp.scb); - printk("scb at %p, scb.status = %04x, .command = %04x," - " .cmd = %08x, .rfd = %08x\n", - &lp->scb, lp->scb.status, lp->scb.command, - lp->scb.cmd, lp->scb.rfd); - printk(" errors: crc %x, align %x, resource %x," - " over %x, rcvdt %x, short %x\n", - lp->scb.crc_err, lp->scb.align_err, lp->scb.resource_err, - lp->scb.over_err, lp->scb.rcvdt_err, lp->scb.short_err); - cmd = lp->cmd_head; - while (cmd != NULL) { - printk("cmd at %p, .status = %04x, .command = %04x, .b_next = %08x\n", - cmd, cmd->status, cmd->command, cmd->b_next); - cmd = cmd->v_next; - } - rfd = lp->rfd_head; - printk("rfd_head = %p\n", rfd); - do { - printk(" %p .stat %04x, .cmd %04x, b_next %08x, rbd %08x," - " count %04x\n", - rfd, rfd->stat, rfd->cmd, rfd->b_next, rfd->rbd, - rfd->count); - rfd = rfd->v_next; - } while (rfd != lp->rfd_head); - rbd = lp->rbd_head; - printk("rbd_head = %p\n", rbd); - do { - printk(" %p .count %04x, b_next %08x, b_data %08x, size %04x\n", - rbd, rbd->count, rbd->b_next, rbd->b_data, rbd->size); - rbd = rbd->v_next; - } while (rbd != lp->rbd_head); - CHECK_INV(lp, lp, sizeof(struct i596_private)); -} - - -#if defined(ENABLE_MVME16x_NET) || defined(ENABLE_BVME6000_NET) -static void i596_error(int irq, void *dev_id) -{ - struct net_device *dev = dev_id; - volatile unsigned char *pcc2 = (unsigned char *) 0xfff42000; - - pcc2[0x28] = 1; - pcc2[0x2b] = 0x1d; - printk("%s: Error interrupt\n", dev->name); - i596_display_data(dev); -} -#endif - -#define virt_to_dma(lp,v) ((lp)->dma_addr + (dma_addr_t)((unsigned long)(v)-(unsigned long)(lp))) - -static inline void init_rx_bufs(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - int i; - struct i596_rfd *rfd; - struct i596_rbd *rbd; - - /* First build the Receive Buffer Descriptor List */ - - for (i = 0, rbd = lp->rbds; i < rx_ring_size; i++, rbd++) { - dma_addr_t dma_addr; - struct sk_buff *skb = dev_alloc_skb(PKT_BUF_SZ + 4); - - if (skb == NULL) - panic("%s: alloc_skb() failed", __FILE__); - skb_reserve(skb, 2); - dma_addr = dma_map_single(lp->dev, skb->data,PKT_BUF_SZ, - DMA_FROM_DEVICE); - skb->dev = dev; - rbd->v_next = rbd+1; - rbd->b_next = WSWAPrbd(virt_to_dma(lp,rbd+1)); - rbd->b_addr = WSWAPrbd(virt_to_dma(lp,rbd)); - rbd->skb = skb; - rbd->v_data = skb->data; - rbd->b_data = WSWAPchar(dma_addr); - rbd->size = PKT_BUF_SZ; - } - lp->rbd_head = lp->rbds; - rbd = lp->rbds + rx_ring_size - 1; - rbd->v_next = lp->rbds; - rbd->b_next = WSWAPrbd(virt_to_dma(lp,lp->rbds)); - - /* Now build the Receive Frame Descriptor List */ - - for (i = 0, rfd = lp->rfds; i < rx_ring_size; i++, rfd++) { - rfd->rbd = I596_NULL; - rfd->v_next = rfd+1; - rfd->v_prev = rfd-1; - rfd->b_next = WSWAPrfd(virt_to_dma(lp,rfd+1)); - rfd->cmd = CMD_FLEX; - } - lp->rfd_head = lp->rfds; - lp->scb.rfd = WSWAPrfd(virt_to_dma(lp,lp->rfds)); - rfd = lp->rfds; - rfd->rbd = WSWAPrbd(virt_to_dma(lp,lp->rbd_head)); - rfd->v_prev = lp->rfds + rx_ring_size - 1; - rfd = lp->rfds + rx_ring_size - 1; - rfd->v_next = lp->rfds; - rfd->b_next = WSWAPrfd(virt_to_dma(lp,lp->rfds)); - rfd->cmd = CMD_EOL|CMD_FLEX; - - CHECK_WBACK_INV(lp, lp, sizeof(struct i596_private)); -} - -static inline void remove_rx_bufs(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - struct i596_rbd *rbd; - int i; - - for (i = 0, rbd = lp->rbds; i < rx_ring_size; i++, rbd++) { - if (rbd->skb == NULL) - break; - dma_unmap_single(lp->dev, - (dma_addr_t)WSWAPchar(rbd->b_data), - PKT_BUF_SZ, DMA_FROM_DEVICE); - dev_kfree_skb(rbd->skb); - } -} - - -static void rebuild_rx_bufs(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - int i; - - /* Ensure rx frame/buffer descriptors are tidy */ - - for (i = 0; i < rx_ring_size; i++) { - lp->rfds[i].rbd = I596_NULL; - lp->rfds[i].cmd = CMD_FLEX; - } - lp->rfds[rx_ring_size-1].cmd = CMD_EOL|CMD_FLEX; - lp->rfd_head = lp->rfds; - lp->scb.rfd = WSWAPrfd(virt_to_dma(lp,lp->rfds)); - lp->rbd_head = lp->rbds; - lp->rfds[0].rbd = WSWAPrbd(virt_to_dma(lp,lp->rbds)); - - CHECK_WBACK_INV(lp, lp, sizeof(struct i596_private)); -} - - -static int init_i596_mem(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - unsigned long flags; - - disable_irq(dev->irq); /* disable IRQs from LAN */ - DEB(DEB_INIT, - printk("RESET 82596 port: %lx (with IRQ %d disabled)\n", - (dev->base_addr + PA_I82596_RESET), - dev->irq)); - - gsc_writel(0, (dev->base_addr + PA_I82596_RESET)); /* Hard Reset */ - udelay(100); /* Wait 100us - seems to help */ - - /* change the scp address */ - - lp->last_cmd = jiffies; - - - lp->scp.sysbus = 0x0000006c; - lp->scp.iscp = WSWAPiscp(virt_to_dma(lp,&(lp->iscp))); - lp->iscp.scb = WSWAPscb(virt_to_dma(lp,&(lp->scb))); - lp->iscp.stat = ISCP_BUSY; - lp->cmd_backlog = 0; - - lp->cmd_head = NULL; - lp->scb.cmd = I596_NULL; - - DEB(DEB_INIT, printk("%s: starting i82596.\n", dev->name)); - - CHECK_WBACK(lp, &(lp->scp), sizeof(struct i596_scp)); - CHECK_WBACK(lp, &(lp->iscp), sizeof(struct i596_iscp)); - - MPU_PORT(dev, PORT_ALTSCP, virt_to_dma(lp,&lp->scp)); - - CA(dev); - - if (wait_istat(dev, lp, 1000, "initialization timed out")) - goto failed; - DEB(DEB_INIT, printk("%s: i82596 initialization successful\n", dev->name)); - - /* Ensure rx frame/buffer descriptors are tidy */ - rebuild_rx_bufs(dev); - - lp->scb.command = 0; - CHECK_WBACK(lp, &(lp->scb), sizeof(struct i596_scb)); - - enable_irq(dev->irq); /* enable IRQs from LAN */ - - DEB(DEB_INIT, printk("%s: queuing CmdConfigure\n", dev->name)); - memcpy(lp->cf_cmd.i596_config, init_setup, sizeof(init_setup)); - lp->cf_cmd.cmd.command = CmdConfigure; - CHECK_WBACK(lp, &(lp->cf_cmd), sizeof(struct cf_cmd)); - i596_add_cmd(dev, &lp->cf_cmd.cmd); - - DEB(DEB_INIT, printk("%s: queuing CmdSASetup\n", dev->name)); - memcpy(lp->sa_cmd.eth_addr, dev->dev_addr, 6); - lp->sa_cmd.cmd.command = CmdSASetup; - CHECK_WBACK(lp, &(lp->sa_cmd), sizeof(struct sa_cmd)); - i596_add_cmd(dev, &lp->sa_cmd.cmd); - - DEB(DEB_INIT, printk("%s: queuing CmdTDR\n", dev->name)); - lp->tdr_cmd.cmd.command = CmdTDR; - CHECK_WBACK(lp, &(lp->tdr_cmd), sizeof(struct tdr_cmd)); - i596_add_cmd(dev, &lp->tdr_cmd.cmd); - - spin_lock_irqsave (&lp->lock, flags); - - if (wait_cmd(dev, lp, 1000, "timed out waiting to issue RX_START")) { - spin_unlock_irqrestore (&lp->lock, flags); - goto failed; - } - DEB(DEB_INIT, printk("%s: Issuing RX_START\n", dev->name)); - lp->scb.command = RX_START; - lp->scb.rfd = WSWAPrfd(virt_to_dma(lp,lp->rfds)); - CHECK_WBACK(lp, &(lp->scb), sizeof(struct i596_scb)); - - CA(dev); - - spin_unlock_irqrestore (&lp->lock, flags); - - if (wait_cmd(dev, lp, 1000, "RX_START not processed")) - goto failed; - DEB(DEB_INIT, printk("%s: Receive unit started OK\n", dev->name)); - - return 0; - -failed: - printk("%s: Failed to initialise 82596\n", dev->name); - MPU_PORT(dev, PORT_RESET, 0); - return -1; -} - - -static inline int i596_rx(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - struct i596_rfd *rfd; - struct i596_rbd *rbd; - int frames = 0; - - DEB(DEB_RXFRAME, printk("i596_rx(), rfd_head %p, rbd_head %p\n", - lp->rfd_head, lp->rbd_head)); - - - rfd = lp->rfd_head; /* Ref next frame to check */ - - CHECK_INV(lp, rfd, sizeof(struct i596_rfd)); - while ((rfd->stat) & STAT_C) { /* Loop while complete frames */ - if (rfd->rbd == I596_NULL) - rbd = NULL; - else if (rfd->rbd == lp->rbd_head->b_addr) { - rbd = lp->rbd_head; - CHECK_INV(lp, rbd, sizeof(struct i596_rbd)); - } - else { - printk("%s: rbd chain broken!\n", dev->name); - /* XXX Now what? */ - rbd = NULL; - } - DEB(DEB_RXFRAME, printk(" rfd %p, rfd.rbd %08x, rfd.stat %04x\n", - rfd, rfd->rbd, rfd->stat)); - - if (rbd != NULL && ((rfd->stat) & STAT_OK)) { - /* a good frame */ - int pkt_len = rbd->count & 0x3fff; - struct sk_buff *skb = rbd->skb; - int rx_in_place = 0; - - DEB(DEB_RXADDR,print_eth(rbd->v_data, "received")); - frames++; - - /* Check if the packet is long enough to just accept - * without copying to a properly sized skbuff. - */ - - if (pkt_len > rx_copybreak) { - struct sk_buff *newskb; - dma_addr_t dma_addr; - - dma_unmap_single(lp->dev,(dma_addr_t)WSWAPchar(rbd->b_data), PKT_BUF_SZ, DMA_FROM_DEVICE); - /* Get fresh skbuff to replace filled one. */ - newskb = dev_alloc_skb(PKT_BUF_SZ + 4); - if (newskb == NULL) { - skb = NULL; /* drop pkt */ - goto memory_squeeze; - } - skb_reserve(newskb, 2); - - /* Pass up the skb already on the Rx ring. */ - skb_put(skb, pkt_len); - rx_in_place = 1; - rbd->skb = newskb; - newskb->dev = dev; - dma_addr = dma_map_single(lp->dev, newskb->data, PKT_BUF_SZ, DMA_FROM_DEVICE); - rbd->v_data = newskb->data; - rbd->b_data = WSWAPchar(dma_addr); - CHECK_WBACK_INV(lp, rbd, sizeof(struct i596_rbd)); - } - else - skb = dev_alloc_skb(pkt_len + 2); -memory_squeeze: - if (skb == NULL) { - /* XXX tulip.c can defer packets here!! */ - printk("%s: i596_rx Memory squeeze, dropping packet.\n", dev->name); - lp->stats.rx_dropped++; - } - else { - if (!rx_in_place) { - /* 16 byte align the data fields */ - dma_sync_single_for_cpu(lp->dev, (dma_addr_t)WSWAPchar(rbd->b_data), PKT_BUF_SZ, DMA_FROM_DEVICE); - skb_reserve(skb, 2); - memcpy(skb_put(skb,pkt_len), rbd->v_data, pkt_len); - dma_sync_single_for_device(lp->dev, (dma_addr_t)WSWAPchar(rbd->b_data), PKT_BUF_SZ, DMA_FROM_DEVICE); - } - skb->len = pkt_len; - skb->protocol=eth_type_trans(skb,dev); - netif_rx(skb); - dev->last_rx = jiffies; - lp->stats.rx_packets++; - lp->stats.rx_bytes+=pkt_len; - } - } - else { - DEB(DEB_ERRORS, printk("%s: Error, rfd.stat = 0x%04x\n", - dev->name, rfd->stat)); - lp->stats.rx_errors++; - if ((rfd->stat) & 0x0001) - lp->stats.collisions++; - if ((rfd->stat) & 0x0080) - lp->stats.rx_length_errors++; - if ((rfd->stat) & 0x0100) - lp->stats.rx_over_errors++; - if ((rfd->stat) & 0x0200) - lp->stats.rx_fifo_errors++; - if ((rfd->stat) & 0x0400) - lp->stats.rx_frame_errors++; - if ((rfd->stat) & 0x0800) - lp->stats.rx_crc_errors++; - if ((rfd->stat) & 0x1000) - lp->stats.rx_length_errors++; - } - - /* Clear the buffer descriptor count and EOF + F flags */ - - if (rbd != NULL && (rbd->count & 0x4000)) { - rbd->count = 0; - lp->rbd_head = rbd->v_next; - CHECK_WBACK_INV(lp, rbd, sizeof(struct i596_rbd)); - } - - /* Tidy the frame descriptor, marking it as end of list */ - - rfd->rbd = I596_NULL; - rfd->stat = 0; - rfd->cmd = CMD_EOL|CMD_FLEX; - rfd->count = 0; - - /* Remove end-of-list from old end descriptor */ - - rfd->v_prev->cmd = CMD_FLEX; - - /* Update record of next frame descriptor to process */ - - lp->scb.rfd = rfd->b_next; - lp->rfd_head = rfd->v_next; - CHECK_WBACK_INV(lp, rfd->v_prev, sizeof(struct i596_rfd)); - CHECK_WBACK_INV(lp, rfd, sizeof(struct i596_rfd)); - rfd = lp->rfd_head; - CHECK_INV(lp, rfd, sizeof(struct i596_rfd)); - } - - DEB(DEB_RXFRAME, printk("frames %d\n", frames)); - - return 0; -} - - -static inline void i596_cleanup_cmd(struct net_device *dev, struct i596_private *lp) -{ - struct i596_cmd *ptr; - - while (lp->cmd_head != NULL) { - ptr = lp->cmd_head; - lp->cmd_head = ptr->v_next; - lp->cmd_backlog--; - - switch ((ptr->command) & 0x7) { - case CmdTx: - { - struct tx_cmd *tx_cmd = (struct tx_cmd *) ptr; - struct sk_buff *skb = tx_cmd->skb; - dma_unmap_single(lp->dev, tx_cmd->dma_addr, skb->len, DMA_TO_DEVICE); - - dev_kfree_skb(skb); - - lp->stats.tx_errors++; - lp->stats.tx_aborted_errors++; - - ptr->v_next = NULL; - ptr->b_next = I596_NULL; - tx_cmd->cmd.command = 0; /* Mark as free */ - break; - } - default: - ptr->v_next = NULL; - ptr->b_next = I596_NULL; - } - CHECK_WBACK_INV(lp, ptr, sizeof(struct i596_cmd)); - } - - wait_cmd(dev, lp, 100, "i596_cleanup_cmd timed out"); - lp->scb.cmd = I596_NULL; - CHECK_WBACK(lp, &(lp->scb), sizeof(struct i596_scb)); -} - - -static inline void i596_reset(struct net_device *dev, struct i596_private *lp) -{ - unsigned long flags; - - DEB(DEB_RESET, printk("i596_reset\n")); - - spin_lock_irqsave (&lp->lock, flags); - - wait_cmd(dev, lp, 100, "i596_reset timed out"); - - netif_stop_queue(dev); - - /* FIXME: this command might cause an lpmc */ - lp->scb.command = CUC_ABORT | RX_ABORT; - CHECK_WBACK(lp, &(lp->scb), sizeof(struct i596_scb)); - CA(dev); - - /* wait for shutdown */ - wait_cmd(dev, lp, 1000, "i596_reset 2 timed out"); - spin_unlock_irqrestore (&lp->lock, flags); - - i596_cleanup_cmd(dev,lp); - i596_rx(dev); - - netif_start_queue(dev); - init_i596_mem(dev); -} - - -static void i596_add_cmd(struct net_device *dev, struct i596_cmd *cmd) -{ - struct i596_private *lp = dev->priv; - unsigned long flags; - - DEB(DEB_ADDCMD, printk("i596_add_cmd cmd_head %p\n", lp->cmd_head)); - - cmd->status = 0; - cmd->command |= (CMD_EOL | CMD_INTR); - cmd->v_next = NULL; - cmd->b_next = I596_NULL; - CHECK_WBACK(lp, cmd, sizeof(struct i596_cmd)); - - spin_lock_irqsave (&lp->lock, flags); - - if (lp->cmd_head != NULL) { - lp->cmd_tail->v_next = cmd; - lp->cmd_tail->b_next = WSWAPcmd(virt_to_dma(lp,&cmd->status)); - CHECK_WBACK(lp, lp->cmd_tail, sizeof(struct i596_cmd)); - } else { - lp->cmd_head = cmd; - wait_cmd(dev, lp, 100, "i596_add_cmd timed out"); - lp->scb.cmd = WSWAPcmd(virt_to_dma(lp,&cmd->status)); - lp->scb.command = CUC_START; - CHECK_WBACK(lp, &(lp->scb), sizeof(struct i596_scb)); - CA(dev); - } - lp->cmd_tail = cmd; - lp->cmd_backlog++; - - spin_unlock_irqrestore (&lp->lock, flags); - - if (lp->cmd_backlog > max_cmd_backlog) { - unsigned long tickssofar = jiffies - lp->last_cmd; - - if (tickssofar < ticks_limit) - return; - - printk("%s: command unit timed out, status resetting.\n", dev->name); -#if 1 - i596_reset(dev, lp); -#endif - } -} - -#if 0 -/* this function makes a perfectly adequate probe... but we have a - device list */ -static int i596_test(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - volatile int *tint; - u32 data; - - tint = (volatile int *)(&(lp->scp)); - data = virt_to_dma(lp,tint); - - tint[1] = -1; - CHECK_WBACK(lp, tint, PAGE_SIZE); - - MPU_PORT(dev, 1, data); - - for(data = 1000000; data; data--) { - CHECK_INV(lp, tint, PAGE_SIZE); - if(tint[1] != -1) - break; - - } - - printk("i596_test result %d\n", tint[1]); - -} -#endif - - -static int i596_open(struct net_device *dev) -{ - DEB(DEB_OPEN, printk("%s: i596_open() irq %d.\n", dev->name, dev->irq)); - - if (request_irq(dev->irq, &i596_interrupt, 0, "i82596", dev)) { - printk("%s: IRQ %d not free\n", dev->name, dev->irq); - goto out; - } - - init_rx_bufs(dev); - - if (init_i596_mem(dev)) { - printk("%s: Failed to init memory\n", dev->name); - goto out_remove_rx_bufs; - } - - netif_start_queue(dev); - - return 0; - -out_remove_rx_bufs: - remove_rx_bufs(dev); - free_irq(dev->irq, dev); -out: - return -EAGAIN; -} - -static void i596_tx_timeout (struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - - /* Transmitter timeout, serious problems. */ - DEB(DEB_ERRORS, printk("%s: transmit timed out, status resetting.\n", - dev->name)); - - lp->stats.tx_errors++; - - /* Try to restart the adaptor */ - if (lp->last_restart == lp->stats.tx_packets) { - DEB(DEB_ERRORS, printk("Resetting board.\n")); - /* Shutdown and restart */ - i596_reset (dev, lp); - } else { - /* Issue a channel attention signal */ - DEB(DEB_ERRORS, printk("Kicking board.\n")); - lp->scb.command = CUC_START | RX_START; - CHECK_WBACK_INV(lp, &(lp->scb), sizeof(struct i596_scb)); - CA (dev); - lp->last_restart = lp->stats.tx_packets; - } - - dev->trans_start = jiffies; - netif_wake_queue (dev); -} - - -static int i596_start_xmit(struct sk_buff *skb, struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - struct tx_cmd *tx_cmd; - struct i596_tbd *tbd; - short length = skb->len; - dev->trans_start = jiffies; - - DEB(DEB_STARTTX, printk("%s: i596_start_xmit(%x,%p) called\n", dev->name, - skb->len, skb->data)); - - if (length < ETH_ZLEN) { - if (skb_padto(skb, ETH_ZLEN)) - return 0; - length = ETH_ZLEN; - } - - netif_stop_queue(dev); - - tx_cmd = lp->tx_cmds + lp->next_tx_cmd; - tbd = lp->tbds + lp->next_tx_cmd; - - if (tx_cmd->cmd.command) { - DEB(DEB_ERRORS, printk("%s: xmit ring full, dropping packet.\n", - dev->name)); - lp->stats.tx_dropped++; - - dev_kfree_skb(skb); - } else { - if (++lp->next_tx_cmd == TX_RING_SIZE) - lp->next_tx_cmd = 0; - tx_cmd->tbd = WSWAPtbd(virt_to_dma(lp,tbd)); - tbd->next = I596_NULL; - - tx_cmd->cmd.command = CMD_FLEX | CmdTx; - tx_cmd->skb = skb; - - tx_cmd->pad = 0; - tx_cmd->size = 0; - tbd->pad = 0; - tbd->size = EOF | length; - - tx_cmd->dma_addr = dma_map_single(lp->dev, skb->data, skb->len, - DMA_TO_DEVICE); - tbd->data = WSWAPchar(tx_cmd->dma_addr); - - DEB(DEB_TXADDR,print_eth(skb->data, "tx-queued")); - CHECK_WBACK_INV(lp, tx_cmd, sizeof(struct tx_cmd)); - CHECK_WBACK_INV(lp, tbd, sizeof(struct i596_tbd)); - i596_add_cmd(dev, &tx_cmd->cmd); - - lp->stats.tx_packets++; - lp->stats.tx_bytes += length; - } - - netif_start_queue(dev); - - return 0; -} - -static void print_eth(unsigned char *add, char *str) -{ - int i; - - printk("i596 0x%p, ", add); - for (i = 0; i < 6; i++) - printk(" %02X", add[i + 6]); - printk(" -->"); - for (i = 0; i < 6; i++) - printk(" %02X", add[i]); - printk(" %02X%02X, %s\n", add[12], add[13], str); -} - - -#define LAN_PROM_ADDR 0xF0810000 - -static int __devinit i82596_probe(struct net_device *dev, - struct device *gen_dev) -{ - int i; - struct i596_private *lp; - char eth_addr[6]; - dma_addr_t dma_addr; - - /* This lot is ensure things have been cache line aligned. */ - BUILD_BUG_ON(sizeof(struct i596_rfd) != 32); - BUILD_BUG_ON(sizeof(struct i596_rbd) & 31); - BUILD_BUG_ON(sizeof(struct tx_cmd) & 31); - BUILD_BUG_ON(sizeof(struct i596_tbd) != 32); -#ifndef __LP64__ - BUILD_BUG_ON(sizeof(struct i596_private) > 4096); -#endif - - if (!dev->base_addr || !dev->irq) - return -ENODEV; - - if (pdc_lan_station_id(eth_addr, dev->base_addr)) { - for (i=0; i < 6; i++) { - eth_addr[i] = gsc_readb(LAN_PROM_ADDR + i); - } - printk(KERN_INFO "%s: MAC of HP700 LAN read from EEPROM\n", __FILE__); - } - - dev->mem_start = (unsigned long) dma_alloc_noncoherent(gen_dev, - sizeof(struct i596_private), &dma_addr, GFP_KERNEL); - if (!dev->mem_start) { - printk(KERN_ERR "%s: Couldn't get shared memory\n", __FILE__); - return -ENOMEM; - } - - for (i = 0; i < 6; i++) - dev->dev_addr[i] = eth_addr[i]; - - /* The 82596-specific entries in the device structure. */ - dev->open = i596_open; - dev->stop = i596_close; - dev->hard_start_xmit = i596_start_xmit; - dev->get_stats = i596_get_stats; - dev->set_multicast_list = set_multicast_list; - dev->tx_timeout = i596_tx_timeout; - dev->watchdog_timeo = TX_TIMEOUT; -#ifdef CONFIG_NET_POLL_CONTROLLER - dev->poll_controller = i596_poll_controller; -#endif - - dev->priv = (void *)(dev->mem_start); - - lp = dev->priv; - memset(lp, 0, sizeof(struct i596_private)); - - lp->scb.command = 0; - lp->scb.cmd = I596_NULL; - lp->scb.rfd = I596_NULL; - spin_lock_init(&lp->lock); - lp->dma_addr = dma_addr; - lp->dev = gen_dev; - - CHECK_WBACK_INV(lp, dev->mem_start, sizeof(struct i596_private)); - - i = register_netdev(dev); - if (i) { - lp = dev->priv; - dma_free_noncoherent(lp->dev, sizeof(struct i596_private), - (void *)dev->mem_start, lp->dma_addr); - return i; - }; - - DEB(DEB_PROBE, printk(KERN_INFO "%s: 82596 at %#3lx,", dev->name, dev->base_addr)); - for (i = 0; i < 6; i++) - DEB(DEB_PROBE, printk(" %2.2X", dev->dev_addr[i])); - DEB(DEB_PROBE, printk(" IRQ %d.\n", dev->irq)); - DEB(DEB_INIT, printk(KERN_INFO "%s: lp at 0x%p (%d bytes), lp->scb at 0x%p\n", - dev->name, lp, (int)sizeof(struct i596_private), &lp->scb)); - - return 0; -} - -#ifdef CONFIG_NET_POLL_CONTROLLER -static void i596_poll_controller(struct net_device *dev) -{ - disable_irq(dev->irq); - i596_interrupt(dev->irq, dev); - enable_irq(dev->irq); -} -#endif - -static irqreturn_t i596_interrupt(int irq, void *dev_id) -{ - struct net_device *dev = dev_id; - struct i596_private *lp; - unsigned short status, ack_cmd = 0; - - if (dev == NULL) { - printk("%s: irq %d for unknown device.\n", __FUNCTION__, irq); - return IRQ_NONE; - } - - lp = dev->priv; - - spin_lock (&lp->lock); - - wait_cmd(dev, lp, 100, "i596 interrupt, timeout"); - status = lp->scb.status; - - DEB(DEB_INTS, printk("%s: i596 interrupt, IRQ %d, status %4.4x.\n", - dev->name, irq, status)); - - ack_cmd = status & 0xf000; - - if (!ack_cmd) { - DEB(DEB_ERRORS, printk("%s: interrupt with no events\n", dev->name)); - spin_unlock (&lp->lock); - return IRQ_NONE; - } - - if ((status & 0x8000) || (status & 0x2000)) { - struct i596_cmd *ptr; - - if ((status & 0x8000)) - DEB(DEB_INTS, printk("%s: i596 interrupt completed command.\n", dev->name)); - if ((status & 0x2000)) - DEB(DEB_INTS, printk("%s: i596 interrupt command unit inactive %x.\n", dev->name, status & 0x0700)); - - while (lp->cmd_head != NULL) { - CHECK_INV(lp, lp->cmd_head, sizeof(struct i596_cmd)); - if (!(lp->cmd_head->status & STAT_C)) - break; - - ptr = lp->cmd_head; - - DEB(DEB_STATUS, printk("cmd_head->status = %04x, ->command = %04x\n", - lp->cmd_head->status, lp->cmd_head->command)); - lp->cmd_head = ptr->v_next; - lp->cmd_backlog--; - - switch ((ptr->command) & 0x7) { - case CmdTx: - { - struct tx_cmd *tx_cmd = (struct tx_cmd *) ptr; - struct sk_buff *skb = tx_cmd->skb; - - if ((ptr->status) & STAT_OK) { - DEB(DEB_TXADDR, print_eth(skb->data, "tx-done")); - } else { - lp->stats.tx_errors++; - if ((ptr->status) & 0x0020) - lp->stats.collisions++; - if (!((ptr->status) & 0x0040)) - lp->stats.tx_heartbeat_errors++; - if ((ptr->status) & 0x0400) - lp->stats.tx_carrier_errors++; - if ((ptr->status) & 0x0800) - lp->stats.collisions++; - if ((ptr->status) & 0x1000) - lp->stats.tx_aborted_errors++; - } - dma_unmap_single(lp->dev, tx_cmd->dma_addr, skb->len, DMA_TO_DEVICE); - dev_kfree_skb_irq(skb); - - tx_cmd->cmd.command = 0; /* Mark free */ - break; - } - case CmdTDR: - { - unsigned short status = ((struct tdr_cmd *)ptr)->status; - - if (status & 0x8000) { - DEB(DEB_ANY, printk("%s: link ok.\n", dev->name)); - } else { - if (status & 0x4000) - printk("%s: Transceiver problem.\n", dev->name); - if (status & 0x2000) - printk("%s: Termination problem.\n", dev->name); - if (status & 0x1000) - printk("%s: Short circuit.\n", dev->name); - - DEB(DEB_TDR, printk("%s: Time %d.\n", dev->name, status & 0x07ff)); - } - break; - } - case CmdConfigure: - /* Zap command so set_multicast_list() knows it is free */ - ptr->command = 0; - break; - } - ptr->v_next = NULL; - ptr->b_next = I596_NULL; - CHECK_WBACK(lp, ptr, sizeof(struct i596_cmd)); - lp->last_cmd = jiffies; - } - - /* This mess is arranging that only the last of any outstanding - * commands has the interrupt bit set. Should probably really - * only add to the cmd queue when the CU is stopped. - */ - ptr = lp->cmd_head; - while ((ptr != NULL) && (ptr != lp->cmd_tail)) { - struct i596_cmd *prev = ptr; - - ptr->command &= 0x1fff; - ptr = ptr->v_next; - CHECK_WBACK_INV(lp, prev, sizeof(struct i596_cmd)); - } - - if ((lp->cmd_head != NULL)) - ack_cmd |= CUC_START; - lp->scb.cmd = WSWAPcmd(virt_to_dma(lp,&lp->cmd_head->status)); - CHECK_WBACK_INV(lp, &lp->scb, sizeof(struct i596_scb)); - } - if ((status & 0x1000) || (status & 0x4000)) { - if ((status & 0x4000)) - DEB(DEB_INTS, printk("%s: i596 interrupt received a frame.\n", dev->name)); - i596_rx(dev); - /* Only RX_START if stopped - RGH 07-07-96 */ - if (status & 0x1000) { - if (netif_running(dev)) { - DEB(DEB_ERRORS, printk("%s: i596 interrupt receive unit inactive, status 0x%x\n", dev->name, status)); - ack_cmd |= RX_START; - lp->stats.rx_errors++; - lp->stats.rx_fifo_errors++; - rebuild_rx_bufs(dev); - } - } - } - wait_cmd(dev, lp, 100, "i596 interrupt, timeout"); - lp->scb.command = ack_cmd; - CHECK_WBACK(lp, &lp->scb, sizeof(struct i596_scb)); - - /* DANGER: I suspect that some kind of interrupt - acknowledgement aside from acking the 82596 might be needed - here... but it's running acceptably without */ - - CA(dev); - - wait_cmd(dev, lp, 100, "i596 interrupt, exit timeout"); - DEB(DEB_INTS, printk("%s: exiting interrupt.\n", dev->name)); - - spin_unlock (&lp->lock); - return IRQ_HANDLED; -} - -static int i596_close(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - unsigned long flags; - - netif_stop_queue(dev); - - DEB(DEB_INIT, printk("%s: Shutting down ethercard, status was %4.4x.\n", - dev->name, lp->scb.status)); - - spin_lock_irqsave(&lp->lock, flags); - - wait_cmd(dev, lp, 100, "close1 timed out"); - lp->scb.command = CUC_ABORT | RX_ABORT; - CHECK_WBACK(lp, &lp->scb, sizeof(struct i596_scb)); - - CA(dev); - - wait_cmd(dev, lp, 100, "close2 timed out"); - spin_unlock_irqrestore(&lp->lock, flags); - DEB(DEB_STRUCT,i596_display_data(dev)); - i596_cleanup_cmd(dev,lp); - - disable_irq(dev->irq); - - free_irq(dev->irq, dev); - remove_rx_bufs(dev); - - return 0; -} - -static struct net_device_stats * - i596_get_stats(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - - return &lp->stats; -} - -/* - * Set or clear the multicast filter for this adaptor. - */ - -static void set_multicast_list(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - int config = 0, cnt; - - DEB(DEB_MULTI, printk("%s: set multicast list, %d entries, promisc %s, allmulti %s\n", - dev->name, dev->mc_count, dev->flags & IFF_PROMISC ? "ON" : "OFF", - dev->flags & IFF_ALLMULTI ? "ON" : "OFF")); - - if ((dev->flags & IFF_PROMISC) && !(lp->cf_cmd.i596_config[8] & 0x01)) { - lp->cf_cmd.i596_config[8] |= 0x01; - config = 1; - } - if (!(dev->flags & IFF_PROMISC) && (lp->cf_cmd.i596_config[8] & 0x01)) { - lp->cf_cmd.i596_config[8] &= ~0x01; - config = 1; - } - if ((dev->flags & IFF_ALLMULTI) && (lp->cf_cmd.i596_config[11] & 0x20)) { - lp->cf_cmd.i596_config[11] &= ~0x20; - config = 1; - } - if (!(dev->flags & IFF_ALLMULTI) && !(lp->cf_cmd.i596_config[11] & 0x20)) { - lp->cf_cmd.i596_config[11] |= 0x20; - config = 1; - } - if (config) { - if (lp->cf_cmd.cmd.command) - printk("%s: config change request already queued\n", - dev->name); - else { - lp->cf_cmd.cmd.command = CmdConfigure; - CHECK_WBACK_INV(lp, &lp->cf_cmd, sizeof(struct cf_cmd)); - i596_add_cmd(dev, &lp->cf_cmd.cmd); - } - } - - cnt = dev->mc_count; - if (cnt > MAX_MC_CNT) - { - cnt = MAX_MC_CNT; - printk("%s: Only %d multicast addresses supported", - dev->name, cnt); - } - - if (dev->mc_count > 0) { - struct dev_mc_list *dmi; - unsigned char *cp; - struct mc_cmd *cmd; - - cmd = &lp->mc_cmd; - cmd->cmd.command = CmdMulticastList; - cmd->mc_cnt = dev->mc_count * 6; - cp = cmd->mc_addrs; - for (dmi = dev->mc_list; cnt && dmi != NULL; dmi = dmi->next, cnt--, cp += 6) { - memcpy(cp, dmi->dmi_addr, 6); - if (i596_debug > 1) - DEB(DEB_MULTI, printk("%s: Adding address %02x:%02x:%02x:%02x:%02x:%02x\n", - dev->name, cp[0],cp[1],cp[2],cp[3],cp[4],cp[5])); - } - CHECK_WBACK_INV(lp, &lp->mc_cmd, sizeof(struct mc_cmd)); - i596_add_cmd(dev, &cmd->cmd); - } -} - -static int debug = -1; -module_param(debug, int, 0); -MODULE_PARM_DESC(debug, "lasi_82596 debug mask"); - -static int num_drivers; -static struct net_device *netdevs[MAX_DRIVERS]; - -static int __devinit -lan_init_chip(struct parisc_device *dev) -{ - struct net_device *netdevice; - int retval; - - if (num_drivers >= MAX_DRIVERS) { - /* max count of possible i82596 drivers reached */ - return -ENOMEM; - } - - if (num_drivers == 0) - printk(KERN_INFO LASI_82596_DRIVER_VERSION "\n"); - - if (!dev->irq) { - printk(KERN_ERR "%s: IRQ not found for i82596 at 0x%lx\n", - __FILE__, dev->hpa.start); - return -ENODEV; - } - - printk(KERN_INFO "Found i82596 at 0x%lx, IRQ %d\n", dev->hpa.start, - dev->irq); - - netdevice = alloc_etherdev(0); - if (!netdevice) - return -ENOMEM; - - netdevice->base_addr = dev->hpa.start; - netdevice->irq = dev->irq; - - retval = i82596_probe(netdevice, &dev->dev); - if (retval) { - free_netdev(netdevice); - return -ENODEV; - } - - if (dev->id.sversion == 0x72) { - ((struct i596_private *)netdevice->priv)->options = OPT_SWAP_PORT; - } - - netdevs[num_drivers++] = netdevice; - - return retval; -} - - -static struct parisc_device_id lan_tbl[] = { - { HPHW_FIO, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x0008a }, - { HPHW_FIO, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x00072 }, - { 0, } -}; - -MODULE_DEVICE_TABLE(parisc, lan_tbl); - -static struct parisc_driver lan_driver = { - .name = "lasi_82596", - .id_table = lan_tbl, - .probe = lan_init_chip, -}; - -static int __devinit lasi_82596_init(void) -{ - if (debug >= 0) - i596_debug = debug; - return register_parisc_driver(&lan_driver); -} - -module_init(lasi_82596_init); - -static void __exit lasi_82596_exit(void) -{ - int i; - - for (i=0; ipriv; - dma_free_noncoherent(lp->dev, sizeof(struct i596_private), - (void *)netdevice->mem_start, lp->dma_addr); - free_netdev(netdevice); - } - num_drivers = 0; - - unregister_parisc_driver(&lan_driver); -} - -module_exit(lasi_82596_exit); +/* lasi_82596.c -- driver for the intel 82596 ethernet controller, as + munged into HPPA boxen . + + This driver is based upon 82596.c, original credits are below... + but there were too many hoops which HP wants jumped through to + keep this code in there in a sane manner. + + 3 primary sources of the mess -- + 1) hppa needs *lots* of cacheline flushing to keep this kind of + MMIO running. + + 2) The 82596 needs to see all of its pointers as their physical + address. Thus virt_to_bus/bus_to_virt are *everywhere*. + + 3) The implementation HP is using seems to be significantly pickier + about when and how the command and RX units are started. some + command ordering was changed. + + Examination of the mach driver leads one to believe that there + might be a saner way to pull this off... anyone who feels like a + full rewrite can be my guest. + + Split 02/13/2000 Sam Creasey (sammy@oh.verio.com) + + 02/01/2000 Initial modifications for parisc by Helge Deller (deller@gmx.de) + 03/02/2000 changes for better/correct(?) cache-flushing (deller) +*/ + +/* 82596.c: A generic 82596 ethernet driver for linux. */ +/* + Based on Apricot.c + Written 1994 by Mark Evans. + This driver is for the Apricot 82596 bus-master interface + + Modularised 12/94 Mark Evans + + + Modified to support the 82596 ethernet chips on 680x0 VME boards. + by Richard Hirst + Renamed to be 82596.c + + 980825: Changed to receive directly in to sk_buffs which are + allocated at open() time. Eliminates copy on incoming frames + (small ones are still copied). Shared data now held in a + non-cached page, so we can run on 68060 in copyback mode. + + TBD: + * look at deferring rx frames rather than discarding (as per tulip) + * handle tx ring full as per tulip + * performace test to tune rx_copybreak + + Most of my modifications relate to the braindead big-endian + implementation by Intel. When the i596 is operating in + 'big-endian' mode, it thinks a 32 bit value of 0x12345678 + should be stored as 0x56781234. This is a real pain, when + you have linked lists which are shared by the 680x0 and the + i596. + + Driver skeleton + Written 1993 by Donald Becker. + Copyright 1993 United States Government as represented by the Director, + National Security Agency. This software may only be used and distributed + according to the terms of the GNU General Public License as modified by SRC, + incorporated herein by reference. + + The author may be reached as becker@scyld.com, or C/O + Scyld Computing Corporation, 410 Severn Ave., Suite 210, Annapolis MD 21403 + + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#define LASI_82596_DRIVER_VERSION "LASI 82596 driver - Revision: 1.30" + +#define PA_I82596_RESET 0 /* Offsets relative to LASI-LAN-Addr.*/ +#define PA_CPU_PORT_L_ACCESS 4 +#define PA_CHANNEL_ATTENTION 8 + +#define OPT_SWAP_PORT 0x0001 /* Need to wordswp on the MPU port */ + +#define DMA_ALLOC dma_alloc_noncoherent +#define DMA_FREE dma_free_noncoherent +#define DMA_WBACK(ndev, addr, len) \ + do { dma_cache_sync((ndev)->dev.parent, (void *)addr, len, DMA_TO_DEVICE); } while (0) + +#define DMA_INV(ndev, addr, len) \ + do { dma_cache_sync((ndev)->dev.parent, (void *)addr, len, DMA_FROM_DEVICE); } while (0) + +#define DMA_WBACK_INV(ndev, addr, len) \ + do { dma_cache_sync((ndev)->dev.parent, (void *)addr, len, DMA_BIDIRECTIONAL); } while (0) + +#define SYSBUS 0x0000006c; + +/* big endian CPU, 82596 "big" endian mode */ +#define SWAP32(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) +#define SWAP16(x) (x) + +#include "lib82596.c" + +MODULE_AUTHOR("Richard Hirst"); +MODULE_DESCRIPTION("i82596 driver"); +MODULE_LICENSE("GPL"); +module_param(i596_debug, int, 0); +MODULE_PARM_DESC(i596_debug, "lasi_82596 debug mask"); + +static inline void ca(struct net_device *dev) +{ + gsc_writel(0, dev->base_addr + PA_CHANNEL_ATTENTION); +} + + +static void mpu_port(struct net_device *dev, int c, dma_addr_t x) +{ + struct i596_private *lp = netdev_priv(dev); + + u32 v = (u32) (c) | (u32) (x); + u16 a, b; + + if (lp->options & OPT_SWAP_PORT) { + a = v >> 16; + b = v & 0xffff; + } else { + a = v & 0xffff; + b = v >> 16; + } + + gsc_writel(a, dev->base_addr + PA_CPU_PORT_L_ACCESS); + udelay(1); + gsc_writel(b, dev->base_addr + PA_CPU_PORT_L_ACCESS); +} + +#define LAN_PROM_ADDR 0xF0810000 + +static int __devinit +lan_init_chip(struct parisc_device *dev) +{ + struct net_device *netdevice; + struct i596_private *lp; + int retval; + int i; + + if (!dev->irq) { + printk(KERN_ERR "%s: IRQ not found for i82596 at 0x%lx\n", + __FILE__, dev->hpa.start); + return -ENODEV; + } + + printk(KERN_INFO "Found i82596 at 0x%lx, IRQ %d\n", dev->hpa.start, + dev->irq); + + netdevice = alloc_etherdev(sizeof(struct i596_private)); + if (!netdevice) + return -ENOMEM; + SET_NETDEV_DEV(netdevice, &dev->dev); + parisc_set_drvdata (dev, netdevice); + + netdevice->base_addr = dev->hpa.start; + netdevice->irq = dev->irq; + + if (pdc_lan_station_id(netdevice->dev_addr, netdevice->base_addr)) { + for (i = 0; i < 6; i++) { + netdevice->dev_addr[i] = gsc_readb(LAN_PROM_ADDR + i); + } + printk(KERN_INFO + "%s: MAC of HP700 LAN read from EEPROM\n", __FILE__); + } + + lp = netdev_priv(netdevice); + lp->options = dev->id.sversion == 0x72 ? OPT_SWAP_PORT : 0; + + retval = i82596_probe(netdevice); + if (retval) { + free_netdev(netdevice); + return -ENODEV; + } + return retval; +} + +static int __devexit lan_remove_chip (struct parisc_device *pdev) +{ + struct net_device *dev = parisc_get_drvdata(pdev); + struct i596_private *lp = netdev_priv(dev); + + unregister_netdev (dev); + DMA_FREE(&pdev->dev, sizeof(struct i596_private), + (void *)lp->dma, lp->dma_addr); + free_netdev (dev); + return 0; +} + +static struct parisc_device_id lan_tbl[] = { + { HPHW_FIO, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x0008a }, + { HPHW_FIO, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x00072 }, + { 0, } +}; + +MODULE_DEVICE_TABLE(parisc, lan_tbl); + +static struct parisc_driver lan_driver = { + .name = "lasi_82596", + .id_table = lan_tbl, + .probe = lan_init_chip, + .remove = __devexit_p(lan_remove_chip), +}; + +static int __devinit lasi_82596_init(void) +{ + printk(KERN_INFO LASI_82596_DRIVER_VERSION "\n"); + return register_parisc_driver(&lan_driver); +} + +module_init(lasi_82596_init); + +static void __exit lasi_82596_exit(void) +{ + unregister_parisc_driver(&lan_driver); +} + +module_exit(lasi_82596_exit); diff --git a/drivers/net/lib82596.c b/drivers/net/lib82596.c new file mode 100644 index 00000000000..5884f5bd04a --- /dev/null +++ b/drivers/net/lib82596.c @@ -0,0 +1,1434 @@ +/* lasi_82596.c -- driver for the intel 82596 ethernet controller, as + munged into HPPA boxen . + + This driver is based upon 82596.c, original credits are below... + but there were too many hoops which HP wants jumped through to + keep this code in there in a sane manner. + + 3 primary sources of the mess -- + 1) hppa needs *lots* of cacheline flushing to keep this kind of + MMIO running. + + 2) The 82596 needs to see all of its pointers as their physical + address. Thus virt_to_bus/bus_to_virt are *everywhere*. + + 3) The implementation HP is using seems to be significantly pickier + about when and how the command and RX units are started. some + command ordering was changed. + + Examination of the mach driver leads one to believe that there + might be a saner way to pull this off... anyone who feels like a + full rewrite can be my guest. + + Split 02/13/2000 Sam Creasey (sammy@oh.verio.com) + + 02/01/2000 Initial modifications for parisc by Helge Deller (deller@gmx.de) + 03/02/2000 changes for better/correct(?) cache-flushing (deller) +*/ + +/* 82596.c: A generic 82596 ethernet driver for linux. */ +/* + Based on Apricot.c + Written 1994 by Mark Evans. + This driver is for the Apricot 82596 bus-master interface + + Modularised 12/94 Mark Evans + + + Modified to support the 82596 ethernet chips on 680x0 VME boards. + by Richard Hirst + Renamed to be 82596.c + + 980825: Changed to receive directly in to sk_buffs which are + allocated at open() time. Eliminates copy on incoming frames + (small ones are still copied). Shared data now held in a + non-cached page, so we can run on 68060 in copyback mode. + + TBD: + * look at deferring rx frames rather than discarding (as per tulip) + * handle tx ring full as per tulip + * performace test to tune rx_copybreak + + Most of my modifications relate to the braindead big-endian + implementation by Intel. When the i596 is operating in + 'big-endian' mode, it thinks a 32 bit value of 0x12345678 + should be stored as 0x56781234. This is a real pain, when + you have linked lists which are shared by the 680x0 and the + i596. + + Driver skeleton + Written 1993 by Donald Becker. + Copyright 1993 United States Government as represented by the Director, + National Security Agency. This software may only be used and distributed + according to the terms of the GNU General Public License as modified by SRC, + incorporated herein by reference. + + The author may be reached as becker@scyld.com, or C/O + Scyld Computing Corporation, 410 Severn Ave., Suite 210, Annapolis MD 21403 + + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* DEBUG flags + */ + +#define DEB_INIT 0x0001 +#define DEB_PROBE 0x0002 +#define DEB_SERIOUS 0x0004 +#define DEB_ERRORS 0x0008 +#define DEB_MULTI 0x0010 +#define DEB_TDR 0x0020 +#define DEB_OPEN 0x0040 +#define DEB_RESET 0x0080 +#define DEB_ADDCMD 0x0100 +#define DEB_STATUS 0x0200 +#define DEB_STARTTX 0x0400 +#define DEB_RXADDR 0x0800 +#define DEB_TXADDR 0x1000 +#define DEB_RXFRAME 0x2000 +#define DEB_INTS 0x4000 +#define DEB_STRUCT 0x8000 +#define DEB_ANY 0xffff + + +#define DEB(x, y) if (i596_debug & (x)) { y; } + + +/* + * The MPU_PORT command allows direct access to the 82596. With PORT access + * the following commands are available (p5-18). The 32-bit port command + * must be word-swapped with the most significant word written first. + * This only applies to VME boards. + */ +#define PORT_RESET 0x00 /* reset 82596 */ +#define PORT_SELFTEST 0x01 /* selftest */ +#define PORT_ALTSCP 0x02 /* alternate SCB address */ +#define PORT_ALTDUMP 0x03 /* Alternate DUMP address */ + +static int i596_debug = (DEB_SERIOUS|DEB_PROBE); + +/* Copy frames shorter than rx_copybreak, otherwise pass on up in + * a full sized sk_buff. Value of 100 stolen from tulip.c (!alpha). + */ +static int rx_copybreak = 100; + +#define PKT_BUF_SZ 1536 +#define MAX_MC_CNT 64 + +#define ISCP_BUSY 0x0001 + +#define I596_NULL ((u32)0xffffffff) + +#define CMD_EOL 0x8000 /* The last command of the list, stop. */ +#define CMD_SUSP 0x4000 /* Suspend after doing cmd. */ +#define CMD_INTR 0x2000 /* Interrupt after doing cmd. */ + +#define CMD_FLEX 0x0008 /* Enable flexible memory model */ + +enum commands { + CmdNOp = 0, CmdSASetup = 1, CmdConfigure = 2, CmdMulticastList = 3, + CmdTx = 4, CmdTDR = 5, CmdDump = 6, CmdDiagnose = 7 +}; + +#define STAT_C 0x8000 /* Set to 0 after execution */ +#define STAT_B 0x4000 /* Command being executed */ +#define STAT_OK 0x2000 /* Command executed ok */ +#define STAT_A 0x1000 /* Command aborted */ + +#define CUC_START 0x0100 +#define CUC_RESUME 0x0200 +#define CUC_SUSPEND 0x0300 +#define CUC_ABORT 0x0400 +#define RX_START 0x0010 +#define RX_RESUME 0x0020 +#define RX_SUSPEND 0x0030 +#define RX_ABORT 0x0040 + +#define TX_TIMEOUT 5 + + +struct i596_reg { + unsigned short porthi; + unsigned short portlo; + u32 ca; +}; + +#define EOF 0x8000 +#define SIZE_MASK 0x3fff + +struct i596_tbd { + unsigned short size; + unsigned short pad; + dma_addr_t next; + dma_addr_t data; + u32 cache_pad[5]; /* Total 32 bytes... */ +}; + +/* The command structure has two 'next' pointers; v_next is the address of + * the next command as seen by the CPU, b_next is the address of the next + * command as seen by the 82596. The b_next pointer, as used by the 82596 + * always references the status field of the next command, rather than the + * v_next field, because the 82596 is unaware of v_next. It may seem more + * logical to put v_next at the end of the structure, but we cannot do that + * because the 82596 expects other fields to be there, depending on command + * type. + */ + +struct i596_cmd { + struct i596_cmd *v_next; /* Address from CPUs viewpoint */ + unsigned short status; + unsigned short command; + dma_addr_t b_next; /* Address from i596 viewpoint */ +}; + +struct tx_cmd { + struct i596_cmd cmd; + dma_addr_t tbd; + unsigned short size; + unsigned short pad; + struct sk_buff *skb; /* So we can free it after tx */ + dma_addr_t dma_addr; +#ifdef __LP64__ + u32 cache_pad[6]; /* Total 64 bytes... */ +#else + u32 cache_pad[1]; /* Total 32 bytes... */ +#endif +}; + +struct tdr_cmd { + struct i596_cmd cmd; + unsigned short status; + unsigned short pad; +}; + +struct mc_cmd { + struct i596_cmd cmd; + short mc_cnt; + char mc_addrs[MAX_MC_CNT*6]; +}; + +struct sa_cmd { + struct i596_cmd cmd; + char eth_addr[8]; +}; + +struct cf_cmd { + struct i596_cmd cmd; + char i596_config[16]; +}; + +struct i596_rfd { + unsigned short stat; + unsigned short cmd; + dma_addr_t b_next; /* Address from i596 viewpoint */ + dma_addr_t rbd; + unsigned short count; + unsigned short size; + struct i596_rfd *v_next; /* Address from CPUs viewpoint */ + struct i596_rfd *v_prev; +#ifndef __LP64__ + u32 cache_pad[2]; /* Total 32 bytes... */ +#endif +}; + +struct i596_rbd { + /* hardware data */ + unsigned short count; + unsigned short zero1; + dma_addr_t b_next; + dma_addr_t b_data; /* Address from i596 viewpoint */ + unsigned short size; + unsigned short zero2; + /* driver data */ + struct sk_buff *skb; + struct i596_rbd *v_next; + dma_addr_t b_addr; /* This rbd addr from i596 view */ + unsigned char *v_data; /* Address from CPUs viewpoint */ + /* Total 32 bytes... */ +#ifdef __LP64__ + u32 cache_pad[4]; +#endif +}; + +/* These values as chosen so struct i596_dma fits in one page... */ + +#define TX_RING_SIZE 32 +#define RX_RING_SIZE 16 + +struct i596_scb { + unsigned short status; + unsigned short command; + dma_addr_t cmd; + dma_addr_t rfd; + u32 crc_err; + u32 align_err; + u32 resource_err; + u32 over_err; + u32 rcvdt_err; + u32 short_err; + unsigned short t_on; + unsigned short t_off; +}; + +struct i596_iscp { + u32 stat; + dma_addr_t scb; +}; + +struct i596_scp { + u32 sysbus; + u32 pad; + dma_addr_t iscp; +}; + +struct i596_dma { + struct i596_scp scp __attribute__((aligned(32))); + volatile struct i596_iscp iscp __attribute__((aligned(32))); + volatile struct i596_scb scb __attribute__((aligned(32))); + struct sa_cmd sa_cmd __attribute__((aligned(32))); + struct cf_cmd cf_cmd __attribute__((aligned(32))); + struct tdr_cmd tdr_cmd __attribute__((aligned(32))); + struct mc_cmd mc_cmd __attribute__((aligned(32))); + struct i596_rfd rfds[RX_RING_SIZE] __attribute__((aligned(32))); + struct i596_rbd rbds[RX_RING_SIZE] __attribute__((aligned(32))); + struct tx_cmd tx_cmds[TX_RING_SIZE] __attribute__((aligned(32))); + struct i596_tbd tbds[TX_RING_SIZE] __attribute__((aligned(32))); +}; + +struct i596_private { + struct i596_dma *dma; + u32 stat; + int last_restart; + struct i596_rfd *rfd_head; + struct i596_rbd *rbd_head; + struct i596_cmd *cmd_tail; + struct i596_cmd *cmd_head; + int cmd_backlog; + u32 last_cmd; + struct net_device_stats stats; + int next_tx_cmd; + int options; + spinlock_t lock; /* serialize access to chip */ + dma_addr_t dma_addr; + void __iomem *mpu_port; + void __iomem *ca; +}; + +static const char init_setup[] = +{ + 0x8E, /* length, prefetch on */ + 0xC8, /* fifo to 8, monitor off */ + 0x80, /* don't save bad frames */ + 0x2E, /* No source address insertion, 8 byte preamble */ + 0x00, /* priority and backoff defaults */ + 0x60, /* interframe spacing */ + 0x00, /* slot time LSB */ + 0xf2, /* slot time and retries */ + 0x00, /* promiscuous mode */ + 0x00, /* collision detect */ + 0x40, /* minimum frame length */ + 0xff, + 0x00, + 0x7f /* *multi IA */ }; + +static int i596_open(struct net_device *dev); +static int i596_start_xmit(struct sk_buff *skb, struct net_device *dev); +static irqreturn_t i596_interrupt(int irq, void *dev_id); +static int i596_close(struct net_device *dev); +static struct net_device_stats *i596_get_stats(struct net_device *dev); +static void i596_add_cmd(struct net_device *dev, struct i596_cmd *cmd); +static void i596_tx_timeout (struct net_device *dev); +static void print_eth(unsigned char *buf, char *str); +static void set_multicast_list(struct net_device *dev); +static inline void ca(struct net_device *dev); +static void mpu_port(struct net_device *dev, int c, dma_addr_t x); + +static int rx_ring_size = RX_RING_SIZE; +static int ticks_limit = 100; +static int max_cmd_backlog = TX_RING_SIZE-1; + +#ifdef CONFIG_NET_POLL_CONTROLLER +static void i596_poll_controller(struct net_device *dev); +#endif + + +static inline int wait_istat(struct net_device *dev, struct i596_dma *dma, int delcnt, char *str) +{ + DMA_INV(dev, &(dma->iscp), sizeof(struct i596_iscp)); + while (--delcnt && dma->iscp.stat) { + udelay(10); + DMA_INV(dev, &(dma->iscp), sizeof(struct i596_iscp)); + } + if (!delcnt) { + printk(KERN_ERR "%s: %s, iscp.stat %04x, didn't clear\n", + dev->name, str, SWAP16(dma->iscp.stat)); + return -1; + } else + return 0; +} + + +static inline int wait_cmd(struct net_device *dev, struct i596_dma *dma, int delcnt, char *str) +{ + DMA_INV(dev, &(dma->scb), sizeof(struct i596_scb)); + while (--delcnt && dma->scb.command) { + udelay(10); + DMA_INV(dev, &(dma->scb), sizeof(struct i596_scb)); + } + if (!delcnt) { + printk(KERN_ERR "%s: %s, status %4.4x, cmd %4.4x.\n", + dev->name, str, + SWAP16(dma->scb.status), + SWAP16(dma->scb.command)); + return -1; + } else + return 0; +} + + +static void i596_display_data(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + struct i596_cmd *cmd; + struct i596_rfd *rfd; + struct i596_rbd *rbd; + + printk(KERN_DEBUG "lp and scp at %p, .sysbus = %08x, .iscp = %08x\n", + &dma->scp, dma->scp.sysbus, SWAP32(dma->scp.iscp)); + printk(KERN_DEBUG "iscp at %p, iscp.stat = %08x, .scb = %08x\n", + &dma->iscp, SWAP32(dma->iscp.stat), SWAP32(dma->iscp.scb)); + printk(KERN_DEBUG "scb at %p, scb.status = %04x, .command = %04x," + " .cmd = %08x, .rfd = %08x\n", + &dma->scb, SWAP16(dma->scb.status), SWAP16(dma->scb.command), + SWAP16(dma->scb.cmd), SWAP32(dma->scb.rfd)); + printk(KERN_DEBUG " errors: crc %x, align %x, resource %x," + " over %x, rcvdt %x, short %x\n", + SWAP32(dma->scb.crc_err), SWAP32(dma->scb.align_err), + SWAP32(dma->scb.resource_err), SWAP32(dma->scb.over_err), + SWAP32(dma->scb.rcvdt_err), SWAP32(dma->scb.short_err)); + cmd = lp->cmd_head; + while (cmd != NULL) { + printk(KERN_DEBUG + "cmd at %p, .status = %04x, .command = %04x," + " .b_next = %08x\n", + cmd, SWAP16(cmd->status), SWAP16(cmd->command), + SWAP32(cmd->b_next)); + cmd = cmd->v_next; + } + rfd = lp->rfd_head; + printk(KERN_DEBUG "rfd_head = %p\n", rfd); + do { + printk(KERN_DEBUG + " %p .stat %04x, .cmd %04x, b_next %08x, rbd %08x," + " count %04x\n", + rfd, SWAP16(rfd->stat), SWAP16(rfd->cmd), + SWAP32(rfd->b_next), SWAP32(rfd->rbd), + SWAP16(rfd->count)); + rfd = rfd->v_next; + } while (rfd != lp->rfd_head); + rbd = lp->rbd_head; + printk(KERN_DEBUG "rbd_head = %p\n", rbd); + do { + printk(KERN_DEBUG + " %p .count %04x, b_next %08x, b_data %08x," + " size %04x\n", + rbd, SWAP16(rbd->count), SWAP32(rbd->b_next), + SWAP32(rbd->b_data), SWAP16(rbd->size)); + rbd = rbd->v_next; + } while (rbd != lp->rbd_head); + DMA_INV(dev, dma, sizeof(struct i596_dma)); +} + + +#define virt_to_dma(lp, v) ((lp)->dma_addr + (dma_addr_t)((unsigned long)(v)-(unsigned long)((lp)->dma))) + +static inline int init_rx_bufs(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + int i; + struct i596_rfd *rfd; + struct i596_rbd *rbd; + + /* First build the Receive Buffer Descriptor List */ + + for (i = 0, rbd = dma->rbds; i < rx_ring_size; i++, rbd++) { + dma_addr_t dma_addr; + struct sk_buff *skb = netdev_alloc_skb(dev, PKT_BUF_SZ + 4); + + if (skb == NULL) + return -1; + skb_reserve(skb, 2); + dma_addr = dma_map_single(dev->dev.parent, skb->data, + PKT_BUF_SZ, DMA_FROM_DEVICE); + rbd->v_next = rbd+1; + rbd->b_next = SWAP32(virt_to_dma(lp, rbd+1)); + rbd->b_addr = SWAP32(virt_to_dma(lp, rbd)); + rbd->skb = skb; + rbd->v_data = skb->data; + rbd->b_data = SWAP32(dma_addr); + rbd->size = SWAP16(PKT_BUF_SZ); + } + lp->rbd_head = dma->rbds; + rbd = dma->rbds + rx_ring_size - 1; + rbd->v_next = dma->rbds; + rbd->b_next = SWAP32(virt_to_dma(lp, dma->rbds)); + + /* Now build the Receive Frame Descriptor List */ + + for (i = 0, rfd = dma->rfds; i < rx_ring_size; i++, rfd++) { + rfd->rbd = I596_NULL; + rfd->v_next = rfd+1; + rfd->v_prev = rfd-1; + rfd->b_next = SWAP32(virt_to_dma(lp, rfd+1)); + rfd->cmd = SWAP16(CMD_FLEX); + } + lp->rfd_head = dma->rfds; + dma->scb.rfd = SWAP32(virt_to_dma(lp, dma->rfds)); + rfd = dma->rfds; + rfd->rbd = SWAP32(virt_to_dma(lp, lp->rbd_head)); + rfd->v_prev = dma->rfds + rx_ring_size - 1; + rfd = dma->rfds + rx_ring_size - 1; + rfd->v_next = dma->rfds; + rfd->b_next = SWAP32(virt_to_dma(lp, dma->rfds)); + rfd->cmd = SWAP16(CMD_EOL|CMD_FLEX); + + DMA_WBACK_INV(dev, dma, sizeof(struct i596_dma)); + return 0; +} + +static inline void remove_rx_bufs(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_rbd *rbd; + int i; + + for (i = 0, rbd = lp->dma->rbds; i < rx_ring_size; i++, rbd++) { + if (rbd->skb == NULL) + break; + dma_unmap_single(dev->dev.parent, + (dma_addr_t)SWAP32(rbd->b_data), + PKT_BUF_SZ, DMA_FROM_DEVICE); + dev_kfree_skb(rbd->skb); + } +} + + +static void rebuild_rx_bufs(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + int i; + + /* Ensure rx frame/buffer descriptors are tidy */ + + for (i = 0; i < rx_ring_size; i++) { + dma->rfds[i].rbd = I596_NULL; + dma->rfds[i].cmd = SWAP16(CMD_FLEX); + } + dma->rfds[rx_ring_size-1].cmd = SWAP16(CMD_EOL|CMD_FLEX); + lp->rfd_head = dma->rfds; + dma->scb.rfd = SWAP32(virt_to_dma(lp, dma->rfds)); + lp->rbd_head = dma->rbds; + dma->rfds[0].rbd = SWAP32(virt_to_dma(lp, dma->rbds)); + + DMA_WBACK_INV(dev, dma, sizeof(struct i596_dma)); +} + + +static int init_i596_mem(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + unsigned long flags; + + mpu_port(dev, PORT_RESET, 0); + udelay(100); /* Wait 100us - seems to help */ + + /* change the scp address */ + + lp->last_cmd = jiffies; + + dma->scp.sysbus = SYSBUS; + dma->scp.iscp = SWAP32(virt_to_dma(lp, &(dma->iscp))); + dma->iscp.scb = SWAP32(virt_to_dma(lp, &(dma->scb))); + dma->iscp.stat = SWAP32(ISCP_BUSY); + lp->cmd_backlog = 0; + + lp->cmd_head = NULL; + dma->scb.cmd = I596_NULL; + + DEB(DEB_INIT, printk(KERN_DEBUG "%s: starting i82596.\n", dev->name)); + + DMA_WBACK(dev, &(dma->scp), sizeof(struct i596_scp)); + DMA_WBACK(dev, &(dma->iscp), sizeof(struct i596_iscp)); + DMA_WBACK(dev, &(dma->scb), sizeof(struct i596_scb)); + + mpu_port(dev, PORT_ALTSCP, virt_to_dma(lp, &dma->scp)); + ca(dev); + if (wait_istat(dev, dma, 1000, "initialization timed out")) + goto failed; + DEB(DEB_INIT, printk(KERN_DEBUG + "%s: i82596 initialization successful\n", + dev->name)); + + if (request_irq(dev->irq, &i596_interrupt, 0, "i82596", dev)) { + printk(KERN_ERR "%s: IRQ %d not free\n", dev->name, dev->irq); + goto failed; + } + + /* Ensure rx frame/buffer descriptors are tidy */ + rebuild_rx_bufs(dev); + + dma->scb.command = 0; + DMA_WBACK(dev, &(dma->scb), sizeof(struct i596_scb)); + + DEB(DEB_INIT, printk(KERN_DEBUG + "%s: queuing CmdConfigure\n", dev->name)); + memcpy(dma->cf_cmd.i596_config, init_setup, 14); + dma->cf_cmd.cmd.command = SWAP16(CmdConfigure); + DMA_WBACK(dev, &(dma->cf_cmd), sizeof(struct cf_cmd)); + i596_add_cmd(dev, &dma->cf_cmd.cmd); + + DEB(DEB_INIT, printk(KERN_DEBUG "%s: queuing CmdSASetup\n", dev->name)); + memcpy(dma->sa_cmd.eth_addr, dev->dev_addr, 6); + dma->sa_cmd.cmd.command = SWAP16(CmdSASetup); + DMA_WBACK(dev, &(dma->sa_cmd), sizeof(struct sa_cmd)); + i596_add_cmd(dev, &dma->sa_cmd.cmd); + + DEB(DEB_INIT, printk(KERN_DEBUG "%s: queuing CmdTDR\n", dev->name)); + dma->tdr_cmd.cmd.command = SWAP16(CmdTDR); + DMA_WBACK(dev, &(dma->tdr_cmd), sizeof(struct tdr_cmd)); + i596_add_cmd(dev, &dma->tdr_cmd.cmd); + + spin_lock_irqsave (&lp->lock, flags); + + if (wait_cmd(dev, dma, 1000, "timed out waiting to issue RX_START")) { + spin_unlock_irqrestore (&lp->lock, flags); + goto failed_free_irq; + } + DEB(DEB_INIT, printk(KERN_DEBUG "%s: Issuing RX_START\n", dev->name)); + dma->scb.command = SWAP16(RX_START); + dma->scb.rfd = SWAP32(virt_to_dma(lp, dma->rfds)); + DMA_WBACK(dev, &(dma->scb), sizeof(struct i596_scb)); + + ca(dev); + + spin_unlock_irqrestore (&lp->lock, flags); + if (wait_cmd(dev, dma, 1000, "RX_START not processed")) + goto failed_free_irq; + DEB(DEB_INIT, printk(KERN_DEBUG + "%s: Receive unit started OK\n", dev->name)); + return 0; + +failed_free_irq: + free_irq(dev->irq, dev); +failed: + printk(KERN_ERR "%s: Failed to initialise 82596\n", dev->name); + mpu_port(dev, PORT_RESET, 0); + return -1; +} + + +static inline int i596_rx(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_rfd *rfd; + struct i596_rbd *rbd; + int frames = 0; + + DEB(DEB_RXFRAME, printk(KERN_DEBUG + "i596_rx(), rfd_head %p, rbd_head %p\n", + lp->rfd_head, lp->rbd_head)); + + + rfd = lp->rfd_head; /* Ref next frame to check */ + + DMA_INV(dev, rfd, sizeof(struct i596_rfd)); + while (rfd->stat & SWAP16(STAT_C)) { /* Loop while complete frames */ + if (rfd->rbd == I596_NULL) + rbd = NULL; + else if (rfd->rbd == lp->rbd_head->b_addr) { + rbd = lp->rbd_head; + DMA_INV(dev, rbd, sizeof(struct i596_rbd)); + } else { + printk(KERN_ERR "%s: rbd chain broken!\n", dev->name); + /* XXX Now what? */ + rbd = NULL; + } + DEB(DEB_RXFRAME, printk(KERN_DEBUG + " rfd %p, rfd.rbd %08x, rfd.stat %04x\n", + rfd, rfd->rbd, rfd->stat)); + + if (rbd != NULL && (rfd->stat & SWAP16(STAT_OK))) { + /* a good frame */ + int pkt_len = SWAP16(rbd->count) & 0x3fff; + struct sk_buff *skb = rbd->skb; + int rx_in_place = 0; + + DEB(DEB_RXADDR, print_eth(rbd->v_data, "received")); + frames++; + + /* Check if the packet is long enough to just accept + * without copying to a properly sized skbuff. + */ + + if (pkt_len > rx_copybreak) { + struct sk_buff *newskb; + dma_addr_t dma_addr; + + dma_unmap_single(dev->dev.parent, + (dma_addr_t)SWAP32(rbd->b_data), + PKT_BUF_SZ, DMA_FROM_DEVICE); + /* Get fresh skbuff to replace filled one. */ + newskb = netdev_alloc_skb(dev, PKT_BUF_SZ + 4); + if (newskb == NULL) { + skb = NULL; /* drop pkt */ + goto memory_squeeze; + } + skb_reserve(newskb, 2); + + /* Pass up the skb already on the Rx ring. */ + skb_put(skb, pkt_len); + rx_in_place = 1; + rbd->skb = newskb; + dma_addr = dma_map_single(dev->dev.parent, + newskb->data, + PKT_BUF_SZ, + DMA_FROM_DEVICE); + rbd->v_data = newskb->data; + rbd->b_data = SWAP32(dma_addr); + DMA_WBACK_INV(dev, rbd, sizeof(struct i596_rbd)); + } else + skb = netdev_alloc_skb(dev, pkt_len + 2); +memory_squeeze: + if (skb == NULL) { + /* XXX tulip.c can defer packets here!! */ + printk(KERN_ERR + "%s: i596_rx Memory squeeze, dropping packet.\n", + dev->name); + lp->stats.rx_dropped++; + } else { + if (!rx_in_place) { + /* 16 byte align the data fields */ + dma_sync_single_for_cpu(dev->dev.parent, + (dma_addr_t)SWAP32(rbd->b_data), + PKT_BUF_SZ, DMA_FROM_DEVICE); + skb_reserve(skb, 2); + memcpy(skb_put(skb, pkt_len), rbd->v_data, pkt_len); + dma_sync_single_for_device(dev->dev.parent, + (dma_addr_t)SWAP32(rbd->b_data), + PKT_BUF_SZ, DMA_FROM_DEVICE); + } + skb->len = pkt_len; + skb->protocol = eth_type_trans(skb, dev); + netif_rx(skb); + dev->last_rx = jiffies; + lp->stats.rx_packets++; + lp->stats.rx_bytes += pkt_len; + } + } else { + DEB(DEB_ERRORS, printk(KERN_DEBUG + "%s: Error, rfd.stat = 0x%04x\n", + dev->name, rfd->stat)); + lp->stats.rx_errors++; + if (rfd->stat & SWAP16(0x0100)) + lp->stats.collisions++; + if (rfd->stat & SWAP16(0x8000)) + lp->stats.rx_length_errors++; + if (rfd->stat & SWAP16(0x0001)) + lp->stats.rx_over_errors++; + if (rfd->stat & SWAP16(0x0002)) + lp->stats.rx_fifo_errors++; + if (rfd->stat & SWAP16(0x0004)) + lp->stats.rx_frame_errors++; + if (rfd->stat & SWAP16(0x0008)) + lp->stats.rx_crc_errors++; + if (rfd->stat & SWAP16(0x0010)) + lp->stats.rx_length_errors++; + } + + /* Clear the buffer descriptor count and EOF + F flags */ + + if (rbd != NULL && (rbd->count & SWAP16(0x4000))) { + rbd->count = 0; + lp->rbd_head = rbd->v_next; + DMA_WBACK_INV(dev, rbd, sizeof(struct i596_rbd)); + } + + /* Tidy the frame descriptor, marking it as end of list */ + + rfd->rbd = I596_NULL; + rfd->stat = 0; + rfd->cmd = SWAP16(CMD_EOL|CMD_FLEX); + rfd->count = 0; + + /* Update record of next frame descriptor to process */ + + lp->dma->scb.rfd = rfd->b_next; + lp->rfd_head = rfd->v_next; + DMA_WBACK_INV(dev, rfd, sizeof(struct i596_rfd)); + + /* Remove end-of-list from old end descriptor */ + + rfd->v_prev->cmd = SWAP16(CMD_FLEX); + DMA_WBACK_INV(dev, rfd->v_prev, sizeof(struct i596_rfd)); + rfd = lp->rfd_head; + DMA_INV(dev, rfd, sizeof(struct i596_rfd)); + } + + DEB(DEB_RXFRAME, printk(KERN_DEBUG "frames %d\n", frames)); + + return 0; +} + + +static inline void i596_cleanup_cmd(struct net_device *dev, struct i596_private *lp) +{ + struct i596_cmd *ptr; + + while (lp->cmd_head != NULL) { + ptr = lp->cmd_head; + lp->cmd_head = ptr->v_next; + lp->cmd_backlog--; + + switch (SWAP16(ptr->command) & 0x7) { + case CmdTx: + { + struct tx_cmd *tx_cmd = (struct tx_cmd *) ptr; + struct sk_buff *skb = tx_cmd->skb; + dma_unmap_single(dev->dev.parent, + tx_cmd->dma_addr, + skb->len, DMA_TO_DEVICE); + + dev_kfree_skb(skb); + + lp->stats.tx_errors++; + lp->stats.tx_aborted_errors++; + + ptr->v_next = NULL; + ptr->b_next = I596_NULL; + tx_cmd->cmd.command = 0; /* Mark as free */ + break; + } + default: + ptr->v_next = NULL; + ptr->b_next = I596_NULL; + } + DMA_WBACK_INV(dev, ptr, sizeof(struct i596_cmd)); + } + + wait_cmd(dev, lp->dma, 100, "i596_cleanup_cmd timed out"); + lp->dma->scb.cmd = I596_NULL; + DMA_WBACK(dev, &(lp->dma->scb), sizeof(struct i596_scb)); +} + + +static inline void i596_reset(struct net_device *dev, struct i596_private *lp) +{ + unsigned long flags; + + DEB(DEB_RESET, printk(KERN_DEBUG "i596_reset\n")); + + spin_lock_irqsave (&lp->lock, flags); + + wait_cmd(dev, lp->dma, 100, "i596_reset timed out"); + + netif_stop_queue(dev); + + /* FIXME: this command might cause an lpmc */ + lp->dma->scb.command = SWAP16(CUC_ABORT | RX_ABORT); + DMA_WBACK(dev, &(lp->dma->scb), sizeof(struct i596_scb)); + ca(dev); + + /* wait for shutdown */ + wait_cmd(dev, lp->dma, 1000, "i596_reset 2 timed out"); + spin_unlock_irqrestore (&lp->lock, flags); + + i596_cleanup_cmd(dev, lp); + i596_rx(dev); + + netif_start_queue(dev); + init_i596_mem(dev); +} + + +static void i596_add_cmd(struct net_device *dev, struct i596_cmd *cmd) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + unsigned long flags; + + DEB(DEB_ADDCMD, printk(KERN_DEBUG "i596_add_cmd cmd_head %p\n", + lp->cmd_head)); + + cmd->status = 0; + cmd->command |= SWAP16(CMD_EOL | CMD_INTR); + cmd->v_next = NULL; + cmd->b_next = I596_NULL; + DMA_WBACK(dev, cmd, sizeof(struct i596_cmd)); + + spin_lock_irqsave (&lp->lock, flags); + + if (lp->cmd_head != NULL) { + lp->cmd_tail->v_next = cmd; + lp->cmd_tail->b_next = SWAP32(virt_to_dma(lp, &cmd->status)); + DMA_WBACK(dev, lp->cmd_tail, sizeof(struct i596_cmd)); + } else { + lp->cmd_head = cmd; + wait_cmd(dev, dma, 100, "i596_add_cmd timed out"); + dma->scb.cmd = SWAP32(virt_to_dma(lp, &cmd->status)); + dma->scb.command = SWAP16(CUC_START); + DMA_WBACK(dev, &(dma->scb), sizeof(struct i596_scb)); + ca(dev); + } + lp->cmd_tail = cmd; + lp->cmd_backlog++; + + spin_unlock_irqrestore (&lp->lock, flags); + + if (lp->cmd_backlog > max_cmd_backlog) { + unsigned long tickssofar = jiffies - lp->last_cmd; + + if (tickssofar < ticks_limit) + return; + + printk(KERN_ERR + "%s: command unit timed out, status resetting.\n", + dev->name); +#if 1 + i596_reset(dev, lp); +#endif + } +} + +static int i596_open(struct net_device *dev) +{ + DEB(DEB_OPEN, printk(KERN_DEBUG + "%s: i596_open() irq %d.\n", dev->name, dev->irq)); + + if (init_rx_bufs(dev)) { + printk(KERN_ERR "%s: Failed to init rx bufs\n", dev->name); + return -EAGAIN; + } + if (init_i596_mem(dev)) { + printk(KERN_ERR "%s: Failed to init memory\n", dev->name); + goto out_remove_rx_bufs; + } + netif_start_queue(dev); + + return 0; + +out_remove_rx_bufs: + remove_rx_bufs(dev); + return -EAGAIN; +} + +static void i596_tx_timeout (struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + + /* Transmitter timeout, serious problems. */ + DEB(DEB_ERRORS, printk(KERN_DEBUG + "%s: transmit timed out, status resetting.\n", + dev->name)); + + lp->stats.tx_errors++; + + /* Try to restart the adaptor */ + if (lp->last_restart == lp->stats.tx_packets) { + DEB(DEB_ERRORS, printk(KERN_DEBUG "Resetting board.\n")); + /* Shutdown and restart */ + i596_reset (dev, lp); + } else { + /* Issue a channel attention signal */ + DEB(DEB_ERRORS, printk(KERN_DEBUG "Kicking board.\n")); + lp->dma->scb.command = SWAP16(CUC_START | RX_START); + DMA_WBACK_INV(dev, &(lp->dma->scb), sizeof(struct i596_scb)); + ca (dev); + lp->last_restart = lp->stats.tx_packets; + } + + dev->trans_start = jiffies; + netif_wake_queue (dev); +} + + +static int i596_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct tx_cmd *tx_cmd; + struct i596_tbd *tbd; + short length = skb->len; + dev->trans_start = jiffies; + + DEB(DEB_STARTTX, printk(KERN_DEBUG + "%s: i596_start_xmit(%x,%p) called\n", + dev->name, skb->len, skb->data)); + + if (length < ETH_ZLEN) { + if (skb_padto(skb, ETH_ZLEN)) + return 0; + length = ETH_ZLEN; + } + + netif_stop_queue(dev); + + tx_cmd = lp->dma->tx_cmds + lp->next_tx_cmd; + tbd = lp->dma->tbds + lp->next_tx_cmd; + + if (tx_cmd->cmd.command) { + DEB(DEB_ERRORS, printk(KERN_DEBUG + "%s: xmit ring full, dropping packet.\n", + dev->name)); + lp->stats.tx_dropped++; + + dev_kfree_skb(skb); + } else { + if (++lp->next_tx_cmd == TX_RING_SIZE) + lp->next_tx_cmd = 0; + tx_cmd->tbd = SWAP32(virt_to_dma(lp, tbd)); + tbd->next = I596_NULL; + + tx_cmd->cmd.command = SWAP16(CMD_FLEX | CmdTx); + tx_cmd->skb = skb; + + tx_cmd->pad = 0; + tx_cmd->size = 0; + tbd->pad = 0; + tbd->size = SWAP16(EOF | length); + + tx_cmd->dma_addr = dma_map_single(dev->dev.parent, skb->data, + skb->len, DMA_TO_DEVICE); + tbd->data = SWAP32(tx_cmd->dma_addr); + + DEB(DEB_TXADDR, print_eth(skb->data, "tx-queued")); + DMA_WBACK_INV(dev, tx_cmd, sizeof(struct tx_cmd)); + DMA_WBACK_INV(dev, tbd, sizeof(struct i596_tbd)); + i596_add_cmd(dev, &tx_cmd->cmd); + + lp->stats.tx_packets++; + lp->stats.tx_bytes += length; + } + + netif_start_queue(dev); + + return 0; +} + +static void print_eth(unsigned char *add, char *str) +{ + int i; + + printk(KERN_DEBUG "i596 0x%p, ", add); + for (i = 0; i < 6; i++) + printk(" %02X", add[i + 6]); + printk(" -->"); + for (i = 0; i < 6; i++) + printk(" %02X", add[i]); + printk(" %02X%02X, %s\n", add[12], add[13], str); +} + +static int __devinit i82596_probe(struct net_device *dev) +{ + int i; + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma; + + /* This lot is ensure things have been cache line aligned. */ + BUILD_BUG_ON(sizeof(struct i596_rfd) != 32); + BUILD_BUG_ON(sizeof(struct i596_rbd) & 31); + BUILD_BUG_ON(sizeof(struct tx_cmd) & 31); + BUILD_BUG_ON(sizeof(struct i596_tbd) != 32); +#ifndef __LP64__ + BUILD_BUG_ON(sizeof(struct i596_dma) > 4096); +#endif + + if (!dev->base_addr || !dev->irq) + return -ENODEV; + + dma = (struct i596_dma *) DMA_ALLOC(dev->dev.parent, + sizeof(struct i596_dma), &lp->dma_addr, GFP_KERNEL); + if (!dma) { + printk(KERN_ERR "%s: Couldn't get shared memory\n", __FILE__); + return -ENOMEM; + } + + /* The 82596-specific entries in the device structure. */ + dev->open = i596_open; + dev->stop = i596_close; + dev->hard_start_xmit = i596_start_xmit; + dev->get_stats = i596_get_stats; + dev->set_multicast_list = set_multicast_list; + dev->tx_timeout = i596_tx_timeout; + dev->watchdog_timeo = TX_TIMEOUT; +#ifdef CONFIG_NET_POLL_CONTROLLER + dev->poll_controller = i596_poll_controller; +#endif + + memset(dma, 0, sizeof(struct i596_dma)); + lp->dma = dma; + + dma->scb.command = 0; + dma->scb.cmd = I596_NULL; + dma->scb.rfd = I596_NULL; + spin_lock_init(&lp->lock); + + DMA_WBACK_INV(dev, dma, sizeof(struct i596_dma)); + + i = register_netdev(dev); + if (i) { + DMA_FREE(dev->dev.parent, sizeof(struct i596_dma), + (void *)dma, lp->dma_addr); + return i; + }; + + DEB(DEB_PROBE, printk(KERN_INFO "%s: 82596 at %#3lx,", + dev->name, dev->base_addr)); + for (i = 0; i < 6; i++) + DEB(DEB_PROBE, printk(" %2.2X", dev->dev_addr[i])); + DEB(DEB_PROBE, printk(" IRQ %d.\n", dev->irq)); + DEB(DEB_INIT, printk(KERN_INFO + "%s: dma at 0x%p (%d bytes), lp->scb at 0x%p\n", + dev->name, dma, (int)sizeof(struct i596_dma), + &dma->scb)); + + return 0; +} + +#ifdef CONFIG_NET_POLL_CONTROLLER +static void i596_poll_controller(struct net_device *dev) +{ + disable_irq(dev->irq); + i596_interrupt(dev->irq, dev); + enable_irq(dev->irq); +} +#endif + +static irqreturn_t i596_interrupt(int irq, void *dev_id) +{ + struct net_device *dev = dev_id; + struct i596_private *lp; + struct i596_dma *dma; + unsigned short status, ack_cmd = 0; + + if (dev == NULL) { + printk(KERN_WARNING "%s: irq %d for unknown device.\n", + __FUNCTION__, irq); + return IRQ_NONE; + } + + lp = netdev_priv(dev); + dma = lp->dma; + + spin_lock (&lp->lock); + + wait_cmd(dev, dma, 100, "i596 interrupt, timeout"); + status = SWAP16(dma->scb.status); + + DEB(DEB_INTS, printk(KERN_DEBUG + "%s: i596 interrupt, IRQ %d, status %4.4x.\n", + dev->name, irq, status)); + + ack_cmd = status & 0xf000; + + if (!ack_cmd) { + DEB(DEB_ERRORS, printk(KERN_DEBUG + "%s: interrupt with no events\n", + dev->name)); + spin_unlock (&lp->lock); + return IRQ_NONE; + } + + if ((status & 0x8000) || (status & 0x2000)) { + struct i596_cmd *ptr; + + if ((status & 0x8000)) + DEB(DEB_INTS, + printk(KERN_DEBUG + "%s: i596 interrupt completed command.\n", + dev->name)); + if ((status & 0x2000)) + DEB(DEB_INTS, + printk(KERN_DEBUG + "%s: i596 interrupt command unit inactive %x.\n", + dev->name, status & 0x0700)); + + while (lp->cmd_head != NULL) { + DMA_INV(dev, lp->cmd_head, sizeof(struct i596_cmd)); + if (!(lp->cmd_head->status & SWAP16(STAT_C))) + break; + + ptr = lp->cmd_head; + + DEB(DEB_STATUS, + printk(KERN_DEBUG + "cmd_head->status = %04x, ->command = %04x\n", + SWAP16(lp->cmd_head->status), + SWAP16(lp->cmd_head->command))); + lp->cmd_head = ptr->v_next; + lp->cmd_backlog--; + + switch (SWAP16(ptr->command) & 0x7) { + case CmdTx: + { + struct tx_cmd *tx_cmd = (struct tx_cmd *) ptr; + struct sk_buff *skb = tx_cmd->skb; + + if (ptr->status & SWAP16(STAT_OK)) { + DEB(DEB_TXADDR, + print_eth(skb->data, "tx-done")); + } else { + lp->stats.tx_errors++; + if (ptr->status & SWAP16(0x0020)) + lp->stats.collisions++; + if (!(ptr->status & SWAP16(0x0040))) + lp->stats.tx_heartbeat_errors++; + if (ptr->status & SWAP16(0x0400)) + lp->stats.tx_carrier_errors++; + if (ptr->status & SWAP16(0x0800)) + lp->stats.collisions++; + if (ptr->status & SWAP16(0x1000)) + lp->stats.tx_aborted_errors++; + } + dma_unmap_single(dev->dev.parent, + tx_cmd->dma_addr, + skb->len, DMA_TO_DEVICE); + dev_kfree_skb_irq(skb); + + tx_cmd->cmd.command = 0; /* Mark free */ + break; + } + case CmdTDR: + { + unsigned short status = SWAP16(((struct tdr_cmd *)ptr)->status); + + if (status & 0x8000) { + DEB(DEB_ANY, + printk(KERN_DEBUG "%s: link ok.\n", + dev->name)); + } else { + if (status & 0x4000) + printk(KERN_ERR + "%s: Transceiver problem.\n", + dev->name); + if (status & 0x2000) + printk(KERN_ERR + "%s: Termination problem.\n", + dev->name); + if (status & 0x1000) + printk(KERN_ERR + "%s: Short circuit.\n", + dev->name); + + DEB(DEB_TDR, + printk(KERN_DEBUG "%s: Time %d.\n", + dev->name, status & 0x07ff)); + } + break; + } + case CmdConfigure: + /* + * Zap command so set_multicast_list() know + * it is free + */ + ptr->command = 0; + break; + } + ptr->v_next = NULL; + ptr->b_next = I596_NULL; + DMA_WBACK(dev, ptr, sizeof(struct i596_cmd)); + lp->last_cmd = jiffies; + } + + /* This mess is arranging that only the last of any outstanding + * commands has the interrupt bit set. Should probably really + * only add to the cmd queue when the CU is stopped. + */ + ptr = lp->cmd_head; + while ((ptr != NULL) && (ptr != lp->cmd_tail)) { + struct i596_cmd *prev = ptr; + + ptr->command &= SWAP16(0x1fff); + ptr = ptr->v_next; + DMA_WBACK_INV(dev, prev, sizeof(struct i596_cmd)); + } + + if (lp->cmd_head != NULL) + ack_cmd |= CUC_START; + dma->scb.cmd = SWAP32(virt_to_dma(lp, &lp->cmd_head->status)); + DMA_WBACK_INV(dev, &dma->scb, sizeof(struct i596_scb)); + } + if ((status & 0x1000) || (status & 0x4000)) { + if ((status & 0x4000)) + DEB(DEB_INTS, + printk(KERN_DEBUG + "%s: i596 interrupt received a frame.\n", + dev->name)); + i596_rx(dev); + /* Only RX_START if stopped - RGH 07-07-96 */ + if (status & 0x1000) { + if (netif_running(dev)) { + DEB(DEB_ERRORS, + printk(KERN_DEBUG + "%s: i596 interrupt receive unit inactive, status 0x%x\n", + dev->name, status)); + ack_cmd |= RX_START; + lp->stats.rx_errors++; + lp->stats.rx_fifo_errors++; + rebuild_rx_bufs(dev); + } + } + } + wait_cmd(dev, dma, 100, "i596 interrupt, timeout"); + dma->scb.command = SWAP16(ack_cmd); + DMA_WBACK(dev, &dma->scb, sizeof(struct i596_scb)); + + /* DANGER: I suspect that some kind of interrupt + acknowledgement aside from acking the 82596 might be needed + here... but it's running acceptably without */ + + ca(dev); + + wait_cmd(dev, dma, 100, "i596 interrupt, exit timeout"); + DEB(DEB_INTS, printk(KERN_DEBUG "%s: exiting interrupt.\n", dev->name)); + + spin_unlock (&lp->lock); + return IRQ_HANDLED; +} + +static int i596_close(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + unsigned long flags; + + netif_stop_queue(dev); + + DEB(DEB_INIT, + printk(KERN_DEBUG + "%s: Shutting down ethercard, status was %4.4x.\n", + dev->name, SWAP16(lp->dma->scb.status))); + + spin_lock_irqsave(&lp->lock, flags); + + wait_cmd(dev, lp->dma, 100, "close1 timed out"); + lp->dma->scb.command = SWAP16(CUC_ABORT | RX_ABORT); + DMA_WBACK(dev, &lp->dma->scb, sizeof(struct i596_scb)); + + ca(dev); + + wait_cmd(dev, lp->dma, 100, "close2 timed out"); + spin_unlock_irqrestore(&lp->lock, flags); + DEB(DEB_STRUCT, i596_display_data(dev)); + i596_cleanup_cmd(dev, lp); + + free_irq(dev->irq, dev); + remove_rx_bufs(dev); + + return 0; +} + +static struct net_device_stats *i596_get_stats(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + + return &lp->stats; +} + +/* + * Set or clear the multicast filter for this adaptor. + */ + +static void set_multicast_list(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + int config = 0, cnt; + + DEB(DEB_MULTI, + printk(KERN_DEBUG + "%s: set multicast list, %d entries, promisc %s, allmulti %s\n", + dev->name, dev->mc_count, + dev->flags & IFF_PROMISC ? "ON" : "OFF", + dev->flags & IFF_ALLMULTI ? "ON" : "OFF")); + + if ((dev->flags & IFF_PROMISC) && + !(dma->cf_cmd.i596_config[8] & 0x01)) { + dma->cf_cmd.i596_config[8] |= 0x01; + config = 1; + } + if (!(dev->flags & IFF_PROMISC) && + (dma->cf_cmd.i596_config[8] & 0x01)) { + dma->cf_cmd.i596_config[8] &= ~0x01; + config = 1; + } + if ((dev->flags & IFF_ALLMULTI) && + (dma->cf_cmd.i596_config[11] & 0x20)) { + dma->cf_cmd.i596_config[11] &= ~0x20; + config = 1; + } + if (!(dev->flags & IFF_ALLMULTI) && + !(dma->cf_cmd.i596_config[11] & 0x20)) { + dma->cf_cmd.i596_config[11] |= 0x20; + config = 1; + } + if (config) { + if (dma->cf_cmd.cmd.command) + printk(KERN_INFO + "%s: config change request already queued\n", + dev->name); + else { + dma->cf_cmd.cmd.command = SWAP16(CmdConfigure); + DMA_WBACK_INV(dev, &dma->cf_cmd, sizeof(struct cf_cmd)); + i596_add_cmd(dev, &dma->cf_cmd.cmd); + } + } + + cnt = dev->mc_count; + if (cnt > MAX_MC_CNT) { + cnt = MAX_MC_CNT; + printk(KERN_NOTICE "%s: Only %d multicast addresses supported", + dev->name, cnt); + } + + if (dev->mc_count > 0) { + struct dev_mc_list *dmi; + unsigned char *cp; + struct mc_cmd *cmd; + + cmd = &dma->mc_cmd; + cmd->cmd.command = SWAP16(CmdMulticastList); + cmd->mc_cnt = SWAP16(dev->mc_count * 6); + cp = cmd->mc_addrs; + for (dmi = dev->mc_list; + cnt && dmi != NULL; + dmi = dmi->next, cnt--, cp += 6) { + memcpy(cp, dmi->dmi_addr, 6); + if (i596_debug > 1) + DEB(DEB_MULTI, + printk(KERN_DEBUG + "%s: Adding address %02x:%02x:%02x:%02x:%02x:%02x\n", + dev->name, cp[0], cp[1], cp[2], cp[3], cp[4], cp[5])); + } + DMA_WBACK_INV(dev, &dma->mc_cmd, sizeof(struct mc_cmd)); + i596_add_cmd(dev, &cmd->cmd); + } +} -- 2.11.4.GIT