From 0247a7bcd4273fa10c4aba9b3f567c659bab2d2b Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Wed, 15 Dec 2010 22:31:28 -0200 Subject: [PATCH] USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport In order to read/write to the i.MX OTG viewport register it is necessary to setup the PORTSCx register first. By default i.MX OTG port is configured for USB serial PHY. In order to use a ULPI PHY the PORTSCx register needs to be configured properly. commit 724c852 (USB: ehci/mxc: compile fix) placed the PORTSC setup after the OTG viewport is accessed and this causes ULPI read/write to fail. Revert the PORTSC setup order. Tested on a MX31PDK board with a ISP1504 transceiver: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver mxc-ehci mxc-ehci.0: initializing i.MX USB Controller ULPI transceiver vendor/product ID 0x04cc/0x1504 Found NXP ISP1504 ULPI transceiver. ULPI integrity check: passed. Signed-off-by: Fabio Estevam Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-mxc.c | 26 ++++++++++++++------------ 1 file changed, 14 insertions(+), 12 deletions(-) diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c index f6e5d44c06b..535dcae7949 100644 --- a/drivers/usb/host/ehci-mxc.c +++ b/drivers/usb/host/ehci-mxc.c @@ -36,14 +36,8 @@ struct ehci_mxc_priv { static int ehci_mxc_setup(struct usb_hcd *hcd) { struct ehci_hcd *ehci = hcd_to_ehci(hcd); - struct device *dev = hcd->self.controller; - struct mxc_usbh_platform_data *pdata = dev_get_platdata(dev); int retval; - /* EHCI registers start at offset 0x100 */ - ehci->caps = hcd->regs + 0x100; - ehci->regs = hcd->regs + 0x100 + - HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase)); dbg_hcs_params(ehci, "reset"); dbg_hcc_params(ehci, "reset"); @@ -65,12 +59,6 @@ static int ehci_mxc_setup(struct usb_hcd *hcd) ehci_reset(ehci); - /* set up the PORTSCx register */ - ehci_writel(ehci, pdata->portsc, &ehci->regs->port_status[0]); - - /* is this really needed? */ - msleep(10); - ehci_port_power(ehci, 0); return 0; } @@ -128,6 +116,7 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev) int irq, ret; struct ehci_mxc_priv *priv; struct device *dev = &pdev->dev; + struct ehci_hcd *ehci; dev_info(&pdev->dev, "initializing i.MX USB Controller\n"); @@ -204,6 +193,19 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev) if (ret < 0) goto err_init; + ehci = hcd_to_ehci(hcd); + + /* EHCI registers start at offset 0x100 */ + ehci->caps = hcd->regs + 0x100; + ehci->regs = hcd->regs + 0x100 + + HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase)); + + /* set up the PORTSCx register */ + ehci_writel(ehci, pdata->portsc, &ehci->regs->port_status[0]); + + /* is this really needed? */ + msleep(10); + /* Initialize the transceiver */ if (pdata->otg) { pdata->otg->io_priv = hcd->regs + ULPI_VIEWPORT_OFFSET; -- 2.11.4.GIT