From 71839f7d162f973f5931d30d1376a2dc5c0bed5a Mon Sep 17 00:00:00 2001 From: Ben Hutchings Date: Thu, 2 Dec 2010 13:46:24 +0000 Subject: [PATCH] sfc: Distinguish critical and non-critical over-temperature conditions Set both the 'maximum' and critical temperature limits for LM87 hardware monitors on Falcon boards. Do not shut down a port until the critical temperature is reached, but warn as soon as the 'maximum' temperature is reached. Signed-off-by: Ben Hutchings Signed-off-by: David S. Miller --- drivers/net/sfc/falcon_boards.c | 109 +++++++++++++++++++++++++++++----------- 1 file changed, 80 insertions(+), 29 deletions(-) diff --git a/drivers/net/sfc/falcon_boards.c b/drivers/net/sfc/falcon_boards.c index cfc29d76758..86180ee02ec 100644 --- a/drivers/net/sfc/falcon_boards.c +++ b/drivers/net/sfc/falcon_boards.c @@ -30,17 +30,28 @@ #define FALCON_BOARD_SFN4112F 0x52 /* Board temperature is about 15°C above ambient when air flow is - * limited. */ + * limited. The maximum acceptable ambient temperature varies + * depending on the PHY specifications but the critical temperature + * above which we should shut down to avoid damage is 80°C. */ #define FALCON_BOARD_TEMP_BIAS 15 +#define FALCON_BOARD_TEMP_CRIT (80 + FALCON_BOARD_TEMP_BIAS) /* SFC4000 datasheet says: 'The maximum permitted junction temperature * is 125°C; the thermal design of the environment for the SFC4000 * should aim to keep this well below 100°C.' */ +#define FALCON_JUNC_TEMP_MIN 0 #define FALCON_JUNC_TEMP_MAX 90 +#define FALCON_JUNC_TEMP_CRIT 125 /***************************************************************************** * Support for LM87 sensor chip used on several boards */ +#define LM87_REG_TEMP_HW_INT_LOCK 0x13 +#define LM87_REG_TEMP_HW_EXT_LOCK 0x14 +#define LM87_REG_TEMP_HW_INT 0x17 +#define LM87_REG_TEMP_HW_EXT 0x18 +#define LM87_REG_TEMP_EXT1 0x26 +#define LM87_REG_TEMP_INT 0x27 #define LM87_REG_ALARMS1 0x41 #define LM87_REG_ALARMS2 0x42 #define LM87_IN_LIMITS(nr, _min, _max) \ @@ -57,6 +68,27 @@ #if defined(CONFIG_SENSORS_LM87) || defined(CONFIG_SENSORS_LM87_MODULE) +static int efx_poke_lm87(struct i2c_client *client, const u8 *reg_values) +{ + while (*reg_values) { + u8 reg = *reg_values++; + u8 value = *reg_values++; + int rc = i2c_smbus_write_byte_data(client, reg, value); + if (rc) + return rc; + } + return 0; +} + +static const u8 falcon_lm87_common_regs[] = { + LM87_REG_TEMP_HW_INT_LOCK, FALCON_BOARD_TEMP_CRIT, + LM87_REG_TEMP_HW_INT, FALCON_BOARD_TEMP_CRIT, + LM87_TEMP_EXT1_LIMITS(FALCON_JUNC_TEMP_MIN, FALCON_JUNC_TEMP_MAX), + LM87_REG_TEMP_HW_EXT_LOCK, FALCON_JUNC_TEMP_CRIT, + LM87_REG_TEMP_HW_EXT, FALCON_JUNC_TEMP_CRIT, + 0 +}; + static int efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info, const u8 *reg_values) { @@ -67,13 +99,12 @@ static int efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info, if (!client) return -EIO; - while (*reg_values) { - u8 reg = *reg_values++; - u8 value = *reg_values++; - rc = i2c_smbus_write_byte_data(client, reg, value); - if (rc) - goto err; - } + rc = efx_poke_lm87(client, reg_values); + if (rc) + goto err; + rc = efx_poke_lm87(client, falcon_lm87_common_regs); + if (rc) + goto err; board->hwmon_client = client; return 0; @@ -91,36 +122,56 @@ static void efx_fini_lm87(struct efx_nic *efx) static int efx_check_lm87(struct efx_nic *efx, unsigned mask) { struct i2c_client *client = falcon_board(efx)->hwmon_client; - s32 alarms1, alarms2; + bool temp_crit, elec_fault, is_failure; + u16 alarms; + s32 reg; /* If link is up then do not monitor temperature */ if (EFX_WORKAROUND_7884(efx) && efx->link_state.up) return 0; - alarms1 = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS1); - alarms2 = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS2); - if (alarms1 < 0) - return alarms1; - if (alarms2 < 0) - return alarms2; - alarms1 &= mask; - alarms2 &= mask >> 8; - if (alarms1 || alarms2) { + reg = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS1); + if (reg < 0) + return reg; + alarms = reg; + reg = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS2); + if (reg < 0) + return reg; + alarms |= reg << 8; + alarms &= mask; + + temp_crit = false; + if (alarms & LM87_ALARM_TEMP_INT) { + reg = i2c_smbus_read_byte_data(client, LM87_REG_TEMP_INT); + if (reg < 0) + return reg; + if (reg > FALCON_BOARD_TEMP_CRIT) + temp_crit = true; + } + if (alarms & LM87_ALARM_TEMP_EXT1) { + reg = i2c_smbus_read_byte_data(client, LM87_REG_TEMP_EXT1); + if (reg < 0) + return reg; + if (reg > FALCON_JUNC_TEMP_CRIT) + temp_crit = true; + } + elec_fault = alarms & ~(LM87_ALARM_TEMP_INT | LM87_ALARM_TEMP_EXT1); + is_failure = temp_crit || elec_fault; + + if (alarms) netif_err(efx, hw, efx->net_dev, - "LM87 detected a hardware failure (status %02x:%02x)" - "%s%s%s\n", - alarms1, alarms2, - (alarms1 & LM87_ALARM_TEMP_INT) ? + "LM87 detected a hardware %s (status %02x:%02x)" + "%s%s%s%s\n", + is_failure ? "failure" : "problem", + alarms & 0xff, alarms >> 8, + (alarms & LM87_ALARM_TEMP_INT) ? "; board is overheating" : "", - (alarms1 & LM87_ALARM_TEMP_EXT1) ? + (alarms & LM87_ALARM_TEMP_EXT1) ? "; controller is overheating" : "", - (alarms1 & ~(LM87_ALARM_TEMP_INT | LM87_ALARM_TEMP_EXT1) - || alarms2) ? - "; electrical fault" : ""); - return -ERANGE; - } + temp_crit ? "; reached critical temperature" : "", + elec_fault ? "; electrical fault" : ""); - return 0; + return is_failure ? -ERANGE : 0; } #else /* !CONFIG_SENSORS_LM87 */ -- 2.11.4.GIT