From 82a1eb11aed82b9c38059c943b5ead6abfafedb0 Mon Sep 17 00:00:00 2001 From: funman Date: Mon, 3 May 2010 22:15:56 +0000 Subject: [PATCH] as3525v2: Use CD Interrupt vs. CD polling in send_cmd() Also enable write support, test_disk passes on all targets Flyspray: FS#11140 Authors: Jack Halpin and myself git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25799 a1c6a512-1295-4272-9138-f99709370657 --- firmware/target/arm/as3525/sd-as3525v2.c | 63 +++++++++++++++++--------------- 1 file changed, 34 insertions(+), 29 deletions(-) diff --git a/firmware/target/arm/as3525/sd-as3525v2.c b/firmware/target/arm/as3525/sd-as3525v2.c index d42f7b46f..fe4d60925 100644 --- a/firmware/target/arm/as3525/sd-as3525v2.c +++ b/firmware/target/arm/as3525/sd-as3525v2.c @@ -338,7 +338,9 @@ bool sd_enabled = false; #endif static struct wakeup transfer_completion_signal; +static struct wakeup command_completion_signal; static volatile bool retry; +static volatile int cmd_error; #if defined(HAVE_MULTIDRIVE) int active_card = 0; @@ -350,7 +352,8 @@ static inline void mci_delay(void) { udelay(1000); } void INT_NAND(void) { MCI_CTRL &= ~INT_ENABLE; - const int status = MCI_MASK_STATUS; + /* use raw status here as we need to check some Ints that are masked */ + const int status = MCI_RAW_STATUS; MCI_RAW_STATUS = status; /* clear status */ @@ -360,6 +363,11 @@ void INT_NAND(void) if( status & (MCI_INT_DTO|MCI_DATA_ERROR)) wakeup_signal(&transfer_completion_signal); + cmd_error = status & MCI_CMD_ERROR; + + if(status & MCI_INT_CD) + wakeup_signal(&command_completion_signal); + MCI_CTRL |= INT_ENABLE; } @@ -394,6 +402,12 @@ static bool send_cmd(const int drive, const int cmd, const int arg, const int fl #define TRANSFER_CMD (cmd == SD_READ_MULTIPLE_BLOCK || \ cmd == SD_WRITE_MULTIPLE_BLOCK) +/* RCRC & RTO interrupts should be set together with the CD interrupt but + * in practice sometimes incorrectly precede the CD interrupt. If we leave + * them masked for now we can check them in the isr by reading raw status when + * the CD int is triggered. + */ + MCI_MASK |= MCI_INT_CD; MCI_ARGUMENT = arg; /* Construct MCI_COMMAND */ @@ -415,19 +429,17 @@ static bool send_cmd(const int drive, const int cmd, const int arg, const int fl /*b23 | CMD_CCS_EXPECTED unused */ /*b31 */ | CMD_DONE_BIT; - int max = 0x40000; - while(MCI_COMMAND & CMD_DONE_BIT) - { - if(--max == 0) /* timeout */ - return false; - } + wakeup_wait(&command_completion_signal, TIMEOUT_BLOCK); + + MCI_MASK &= ~MCI_INT_CD; + + /* Handle command responses */ /* TODO Check crc values to determine if the response was valid */ if(flags & MCI_RESP) { - int i = 0xff; while(i--) ; - /* if we read the response too fast we might read the response - * of the previous command instead */ + if(cmd_error & MCI_INT_RCRC) /* skipping timeout for now */ + return false; if(flags & MCI_LONG_RESP) { @@ -498,6 +510,9 @@ static int sd_init_card(const int drive) #endif /* End of Card Identification Mode ************************************/ + /* Card back to full speed */ + MCI_CLKDIV &= ~(0xFF); /* CLK_DIV_0 : bits 7:0 = 0x00 */ + /* Attempt to switch cards to HS timings, non HS cards just ignore this */ /* CMD7 w/rca: Select card to put it in TRAN state */ if(!send_cmd(drive, SD_SELECT_CARD, card_info[drive].rca, MCI_RESP, &response)) @@ -509,7 +524,6 @@ static int sd_init_card(const int drive) /* CMD6 */ if(!send_cmd(drive, SD_SWITCH_FUNC, 0x80fffff1, MCI_NO_RESP, NULL)) return -9; - mci_delay(); /* We need to go back to STBY state now so we can read csd */ /* CMD7 w/rca=0: Deselect card to put it in STBY state */ @@ -523,8 +537,6 @@ static int sd_init_card(const int drive) sd_parse_csd(&card_info[drive]); - /* Card back to full speed */ - MCI_CLKDIV &= ~(0xFF); /* CLK_DIV_0 : bits 7:0 = 0x00 */ #ifndef HAVE_MULTIDRIVE /* CMD7 w/rca: Select card to put it in TRAN state */ @@ -686,7 +698,7 @@ int sd_init(void) | 1; /* clock source = PLLA */ wakeup_init(&transfer_completion_signal); - + wakeup_init(&command_completion_signal); #ifdef HAVE_MULTIDRIVE /* clear previous irq */ GPIOA_IC = EXT_SD_BITS; @@ -729,9 +741,7 @@ static int sd_wait_for_state(const int drive, unsigned int state) { long tick; - if(!send_cmd(drive, SD_SEND_STATUS, card_info[drive].rca, - MCI_RESP, &response)) - return -1; + while(!(send_cmd(drive, SD_SEND_STATUS, card_info[drive].rca, MCI_RESP, &response))); if (((response >> 9) & 0xf) == state) return 0; @@ -818,15 +828,11 @@ static int sd_transfer_sectors(IF_MD2(int drive,) unsigned long start, } MCI_MASK |= (MCI_DATA_ERROR | MCI_INT_DTO); - MCI_CTRL |= DMA_ENABLE; int arg = start; if(!(card_info[drive].ocr & (1<<30))) /* not SDHC */ arg *= SD_BLOCK_SIZE; - if(!send_cmd(drive, cmd, arg, MCI_NO_RESP, NULL)) - panicf("%s multiple blocks failed", write ? "write" : "read"); - if(write) dma_enable_channel(0, dma_buf, MCI_FIFO, DMA_PERI_SD, DMAC_FLOWCTRL_PERI_MEM_TO_PERI, true, false, 0, DMA_S8, NULL); @@ -834,6 +840,12 @@ static int sd_transfer_sectors(IF_MD2(int drive,) unsigned long start, dma_enable_channel(0, MCI_FIFO, dma_buf, DMA_PERI_SD, DMAC_FLOWCTRL_PERI_PERI_TO_MEM, false, true, 0, DMA_S8, NULL); + MCI_CTRL |= DMA_ENABLE; + + unsigned long dummy; /* if we don't ask for a response, writing fails */ + if(!send_cmd(drive, cmd, arg, MCI_RESP, &dummy)) + panicf("%s multiple blocks failed", write ? "write" : "read"); + wakeup_wait(&transfer_completion_signal, TIMEOUT_BLOCK); MCI_MASK &= ~(MCI_DATA_ERROR | MCI_INT_DTO); @@ -904,14 +916,7 @@ int sd_write_sectors(IF_MD2(int drive,) unsigned long start, int count, (void) buf; return -1; #else - //return sd_transfer_sectors(IF_MD2(drive,) start, count, (void*)buf, true); -#ifdef HAVE_MULTIDRIVE - (void)drive; -#endif - (void)start; - (void)count; - (void)buf; - return -1; /* not working, seems to cause FIFO overruns */ + return sd_transfer_sectors(IF_MD2(drive,) start, count, (void*)buf, true); #endif /* defined(BOOTLOADER) */ } -- 2.11.4.GIT