From 5e15fb7713c2315ecf50ca59b83b07f820b79a44 Mon Sep 17 00:00:00 2001 From: b0hoon Date: Wed, 28 Apr 2010 20:55:27 +0000 Subject: [PATCH] Packard Bell Vibe: language corrections in the manual, thanks to: AlexP, linuxstb. git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25752 a1c6a512-1295-4272-9138-f99709370657 --- manual/rockbox_interface/main.tex | 25 ++++++++++++------------- 1 file changed, 12 insertions(+), 13 deletions(-) diff --git a/manual/rockbox_interface/main.tex b/manual/rockbox_interface/main.tex index 0acb5ad25..3103883a4 100644 --- a/manual/rockbox_interface/main.tex +++ b/manual/rockbox_interface/main.tex @@ -409,21 +409,21 @@ detail in the following paragraph. Hold or lay the \dap{} so that the side with the controls and LCD is facing towards you. Below the LCD is the touch sensitive pad with the \ButtonMenu{}, \ButtonPlay{}, \ButtonLeft{}, \ButtonRight{} controls and the scroll pad in the centre. The - scroll pad is oriented vertically and it is between the \ButtonOK{} and \ButtonCancel{} buttons. - Sliding the finger between these buttons down or up acts as \ButtonDown{} or \ButtonUp{} - action respectively. Note that the scroll pad is sensitive, so you will need to move + scroll pad is oriented vertically between the \ButtonOK{} and \ButtonCancel{} buttons. + Sliding a finger up or down the scroll pad acts as \ButtonUp{} and \ButtonDown{} respectively. + Note that the scroll pad is sensitive, so you will need to move slowly at first and get a feel for how it works. There are two buttons on the right hand side of the \dap{}: \ButtonPower{} on the top and \ButtonRec{} underneath. Under these buttons, from top to bottom you can find: USB connector, - power connector and the reset hole to make a hardware reset. + power connector and the reset hole if you need to perform a hardware reset. The \ButtonHold{} switch is located on the left hand side of the \dap{}. Note that when the - \ButtonHold{} switch is moved to the top of the \dap{}, hold is on, and none of the other - controls do anything. Be sure \ButtonHold{} is off before trying to use your player. + \ButtonHold{} switch is moved towards the top of the \dap{}, hold is turned on and all the + other controls are disabled. Be sure \ButtonHold{} is off before trying to use your player. - On the top on the \dap{} is the internal microphone on the left and the line-in jack, near - the headphone jack on the right.} + On the top on the \dap{} is the internal microphone on the left and the line-in socket on the + right, near the headphone socket.} % \opt{player}{ The main controls of this player are a four-way button on the right below @@ -639,11 +639,10 @@ To turn on and off your Rockbox enabled \dap{} use the following keys: \opt{vibe500} { - Rockbox has a dual-boot feature. It loads the original firmware from - the file \fname{/System/OF.mi4}. To boot into the original firmware, - press the \ButtonPower{} normally, without holding it. After the backlight - reaction (when it turns on) immediately press and hold the \ButtonOK{} - button. + Rockbox has a dual-boot feature where it is possible to load the original firmware from + the file \fname{/System/OF.mi4}. To boot into the original firmware press and release + \ButtonPower{} and then immediately after the backlight turns on, press the \ButtonOK{} + button and keep it pressed until the original firmware starts. } } -- 2.11.4.GIT